AD ADG1609BCPZ-REEL7 4.5 î© ron, 4-/8-channel â±5 v,12 v, 5 v, and 3.3 v multiplexer Datasheet

4.5 Ω RON, 4-/8-Channel
±5 V,+12 V, +5 V, and +3.3 V Multiplexers
ADG1608/ADG1609
FEATURES
FUNCTIONAL BLOCK DIAGRAMS
4.5 Ω typical on resistance
1 Ω on-resistance flatness
Up to 470 mA continuous current
±3.3 V to ±8 V dual-supply operation
3.3 V to 16 V single-supply operation
No VL supply required
3 V logic-compatible inputs
Rail-to-rail operation
16-lead TSSOP and 16-lead, 3 mm × 3 mm LFCSP
ADG1608
S1
D
S8
APPLICATIONS
A0 A1 A2 EN
08318-001
1-OF-8
DECODER
Figure 1.
Communication systems
Medical systems
Audio signal routing
Video signal routing
Automatic test equipment
Data acquisition systems
Battery-powered systems
Sample-and-hold systems
Relay replacements
ADG1609
S1A
DA
S4A
S1B
DB
S4B
A0
A1
EN
08318-002
1-OF-4
DECODER
Figure 2.
GENERAL DESCRIPTION
The ADG1608/ADG1609 are monolithic CMOS analog multiplexers comprising eight single channels and four differential
channels, respectively. The ADG1608 switches one of eight
inputs to a common output, as determined by the 3-bit binary
address lines, A0, A1, and A2. The ADG1609 switches one of
four differential inputs to a common differential output, as
determined by the 2-bit binary address lines, A0 and A1. An
EN input on both devices is used to enable or disable the device.
When disabled, all channels are switched off.
The low on resistance of these switches make them ideal solutions for data acquisition and gain switching applications where
low on resistance and distortion is critical. The on-resistance
profile is very flat over the full analog input range, ensuring
excellent linearity and low distortion when switching audio
signals.
Each switch conducts equally well in both directions when on
and has an input signal range that extends to the supplies. In the
off condition, signal levels up to the supplies are blocked. All
switches exhibit break-before-make switching action. Inherent
in the design is low charge injection for minimum transients
when switching the digital inputs.
PRODUCT HIGHLIGHTS
CMOS construction ensures ultralow power dissipation,
making the parts ideally suited for portable and batterypowered instruments.
1.
2.
3.
4.
5.
6.
8 Ω maximum on resistance over temperature.
Minimum distortion: THD + N = 0.04%
3 V logic-compatible digital inputs: VINH = 2.0 V, VINL = 0.8 V.
No VL logic power supply required.
Ultralow power dissipation: <8 nW.
16-lead TSSOP and 16-lead, 3 mm × 3 mm LFCSP.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2009 Analog Devices, Inc. All rights reserved.
ADG1608/ADG1609
TABLE OF CONTENTS
Features .............................................................................................. 1
Continuous Current per Channel, S or D ..................................7
Applications ....................................................................................... 1
Absolute Maximum Ratings ............................................................8
Functional Block Diagrams ............................................................. 1
ESD Caution...................................................................................8
General Description ......................................................................... 1
Pin Configurations and Function Descriptions ............................9
Product Highlights ........................................................................... 1
Typical Performance Characteristics ........................................... 11
Revision History ............................................................................... 2
Test Circuits ..................................................................................... 14
Specifications..................................................................................... 3
Terminology .................................................................................... 17
±5 V Dual Supply ......................................................................... 3
Outline Dimensions ....................................................................... 18
12 V Single Supply ........................................................................ 4
Ordering Guide .......................................................................... 18
5 V Single Supply .......................................................................... 4
3.3 V Single Supply ....................................................................... 6
REVISION HISTORY
7/09—Revision 0: Initial Version
Rev. 0 | Page 2 of 20
ADG1608/ADG1609
SPECIFICATIONS
±5 V DUAL SUPPLY
VDD = +5 V ± 10%, VSS = −5 V ± 10%, GND = 0 V, unless otherwise noted.
Table 1.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
On-Resistance Match Between Channels (∆RON)
On-Resistance Flatness (RFLAT(ON))
LEAKAGE CURRENTS
Source Off Leakage, IS (Off)
Drain Off Leakage, ID (Off)
ADG1608
ADG1609
Channel On Leakage, ID, IS (On)
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IINL or IINH
25°C
−40°C to
+85°C
−40°C to
+125°C
VDD to VSS
4.5
5
0.12
0.25
1
1.3
7
8
0.3
0.35
1.7
2
tON (EN)
tOFF (EN)
Break-Before-Make Time Delay, tD
VS = ±4.5 V, IS = −10 mA
VS = ±4.5 V, VD = ∓4.5 V; see Figure 26
VS = ±4.5 V, VD = ∓4.5 V; see Figure 26
±0.5
±3
nA max
nA typ
±0.15
±0.15
±0.03
±0.15
±2
±1
±14
±7
±2
±14
nA max
nA max
nA typ
nA max
2.0
0.8
±1
4
150
182
106
132
113
144
47
V min
V max
nA typ
μA max
pF typ
VS = VD = ±4.5 V; see Figure 27
VIN = VGND or VDD
24
−64
−64
0.04
ns typ
ns max
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
dB typ
dB typ
% typ
40
71
20
MHz typ
MHz typ
pF typ
VS = 0 V, f = 1 MHz
120
61
pF typ
pF typ
VS = 0 V, f = 1 MHz
VS = 0 V, f = 1 MHz
153
85
pF typ
pF typ
VS = 0 V, f = 1 MHz
VS = 0 V, f = 1 MHz
VDD = +5.5 V, VSS = −5.5 V
Digital inputs = 0 V or VDD
230
258
150
160
178
202
0.001
VDD/VSS
1
VS = ±4.5 V, IS = −10 mA; see Figure 25
VDD = ±4.5 V, VSS = ±4.5 V
VS = ±4.5 V, IS = −10 mA
nA typ
±0.1
±0.03
30
Charge Injection
Off Isolation
Channel-to-Channel Crosstalk
Total Harmonic Distortion + Noise (THD + N)
−3 dB Bandwidth
ADG1608
ADG1609
CS (Off)
CD (Off)
ADG1608
ADG1609
CD, CS (On)
ADG1608
ADG1609
POWER REQUIREMENTS
IDD
V
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
Test Conditions/Comments
VDD = +5.5 V, VSS = −5.5 V
±0.02
±0.1
Digital Input Capacitance, CIN
DYNAMIC CHARACTERISTICS 1
Transition Time, tTRANSITION
Unit
1.0
±3.3/±8
Guaranteed by design, but not subject to production test.
Rev. 0 | Page 3 of 20
μA typ
μA max
V min/max
RL = 300 Ω, CL = 35 pF
VS = 2.5 V; see Figure 28
RL = 300 Ω, CL = 35 pF
VS = 2.5 V; see Figure 30
RL = 300 Ω, CL = 35 pF
VS = 2.5 V; see Figure 30
RL = 300 Ω, CL = 35 pF
VS1 = VS2 = 2.5 V; see Figure 29
VS = 0 V, RS = 0 Ω, CL = 1 nF; see Figure 31
RL = 50 Ω, CL = 5 pF, f = 1 MHz; see Figure 32
RL = 50 Ω, CL = 5 pF, f = 1 MHz; see Figure 34
RL = 110 Ω, VS = 5 V p-p, f = 20 Hz to 20 kHz; see Figure 35
RL = 50 Ω, CL = 5 pF; see Figure 33
ADG1608/ADG1609
12 V SINGLE SUPPLY
VDD = 12 V ± 10%, VSS = 0 V, GND = 0 V, unless otherwise noted.
Table 2.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
On-Resistance Match Between Channels (∆RON)
On-Resistance Flatness (RFLAT(ON))
LEAKAGE CURRENTS
Source Off Leakage, IS (Off)
Drain Off Leakage, ID (Off)
ADG1608
ADG1609
Channel On Leakage, ID, IS (On)
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IINL or IINH
25°C
−40°C to
+85°C
−40°C to
+125°C
0 V to VDD
4
4.5
0.12
0.25
0.9
1.2
±0.02
±0.1
±0.03
±0.15
±0.15
±0.03
±0.15
6.5
7.5
0.3
0.35
1.6
1.9
±0.5
±3
±2
±1
±14
±7
±2
±14
2.0
0.8
±1
±0.1
Digital Input Capacitance, CIN
DYNAMIC CHARACTERISTICS1
Transition Time, tTRANSITION
tON (EN)
tOFF (EN)
Break-Before-Make Time Delay, tD
4
113
141
80
94
77
93
47
VDD = 13.2 V, VSS = 0 V
VS = 1 V/10 V, VD = 10 V/1 V; see Figure 26
VS = 1 V/10 V, VD = 10 V/1 V; see Figure 26
VS = VD = 1 V or 10 V; see Figure 27
VIN = VGND or VDD
MHz typ
MHz typ
pF typ
VS = 6 V, f = 1 MHz
117
59
pF typ
pF typ
VS = 6 V, f = 1 MHz
VS = 6 V, f = 1 MHz
149
84
pF typ
pF typ
VS = 6 V, f = 1 MHz
VS = 6 V, f = 1 MHz
VDD = 12 V
Digital inputs = 0 V or VDD
110
117
140
0.001
300
225
VDD
1
V min
V max
nA typ
μA max
pF typ
VS = 0 V to 10 V, IS = −10 mA
40
78
19
101
480
ADG1609
nA typ
nA max
nA typ
nA max
nA max
nA typ
nA max
VS = 0 V to 10 V, IS = −10 mA; see Figure 25
VDD = 10.8 V, VSS = 0 V
VS = 10 V, IS = −10 mA
29
−64
−64
0.04
196
1.0
ADG1608
V
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
Test Conditions/Comments
ns typ
ns max
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
dB typ
dB typ
% typ
172
30
Charge Injection
Off Isolation
Channel-to-Channel Crosstalk
Total Harmonic Distortion + Noise (THD + N)
−3 dB Bandwidth
ADG1608
ADG1609
CS (Off)
CD (Off)
ADG1608
ADG1609
CD, CS (On)
ADG1608
ADG1609
POWER REQUIREMENTS
IDD
Unit
360
3.3/16
μA typ
μA max
μA typ
μA max
μA typ
μA max
V min/max
Guaranteed by design, but not subject to production test.
Rev. 0 | Page 4 of 20
RL = 300 Ω, CL = 35 pF
VS = 8 V; see Figure 28
RL = 300 Ω, CL = 35 pF
VS = 8 V; see Figure 30
RL = 300 Ω, CL = 35 pF
VS = 8 V; see Figure 30
RL = 300 Ω, CL = 35 pF
VS1 = VS2 = 8 V; see Figure 29
VS = 6 V, RS = 0 Ω, CL = 1 nF; see Figure 31
RL = 50 Ω, CL = 5 pF, f = 1 MHz; see Figure 32
RL = 50 Ω, CL = 5 pF, f = 1 MHz; see Figure 34
RL = 110 Ω, VS = 5 V p-p, f = 20 Hz to 20 kHz; see Figure 35
RL = 50 Ω, CL = 5 pF; see Figure 33
Digital inputs = 5 V
Digital inputs = 5 V
ADG1608/ADG1609
5 V SINGLE SUPPLY
VDD = 5 V ± 10%, VSS = 0 V, GND = 0 V, unless otherwise noted.
Table 3.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
On-Resistance Match Between Channels (∆RON)
On-Resistance Flatness (RFLAT(ON))
LEAKAGE CURRENTS
Source Off Leakage, IS (Off)
Drain Off Leakage, ID (Off)
ADG1608
ADG1609
Channel On Leakage, ID, IS (On)
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IINL or IINH
25°C
−40°Cto
+85°C
−40°C to
+125°C
0 V to VDD
8.5
10
0.15
0.3
1.7
2.3
±0.01
±0.1
±0.01
±0.15
±0.15
±0.01
±0.15
12.5
14
0.35
0.4
2.7
3
±0.5
±3
±2
±1
±14
±7
±2
±14
2.0
0.8
±1
±0.1
Digital Input Capacitance, CIN
DYNAMIC CHARACTERISTICS 1
Transition Time, tTRANSITION
tON (EN)
tOFF (EN)
Break-Before-Make Time Delay, tD
4
193
251
115
152
140
184
66
nA typ
nA max
nA typ
nA max
nA max
nA typ
nA max
V min
V max
nA typ
μA max
pF typ
11
−64
−64
0.3
37
72
22
MHz typ
MHz typ
pF typ
136
68
pF typ
pF typ
168
94
pF typ
pF typ
0.001
μA typ
μA max
V min/max
339
171
184
225
259
Test Conditions/Comments
VS = 0 V to 4.5 V, IS = −10 mA; see Figure 25
VDD = 4.5 V, VSS = 0 V
VS = 0 V to 4.5 V, IS = −10 mA
VS = 0 V to 4.5 V, IS = −10 mA
VDD = 5.5 V, VSS = 0 V
VS = 1 V/4.5 V, VD = 4.5 V/1 V; see Figure 26
VS = 1 V/4.5 V, VD = 4.5 V/1 V; see Figure 26
VS = VD = 1 V or 4.5 V; see Figure 27
VIN = VGND or VDD
RL = 300 Ω, CL = 35 pF
VS = 2.5 V; see Figure 28
RL = 300 Ω, CL = 35 pF
VS = 2.5 V; see Figure 30
RL = 300 Ω, CL = 35 pF
VS = 2.5 V; see Figure 30
RL = 300 Ω, CL = 35 pF
VS1 = VS2 = 2.5 V; see Figure 29
VS = 2.5 V, RS = 0 Ω, CL = 1 nF; see Figure 31
RL = 50 Ω, CL = 5 pF, f = 100 kHz; see Figure 32
RL = 50 Ω, CL = 5 pF, f = 100 kHz; see Figure 34
RL = 110 Ω, f = 20 Hz to 20 kHz, VS = 3.5 V p-p; see Figure 35
RL = 50 Ω, CL = 5 pF; see Figure 33
VS = 2.5 V, f = 1 MHz
VS = 2.5 V, f = 1 MHz
VS = 2.5 V, f = 1 MHz
VDD
1
V
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
ns typ
ns max
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
dB typ
dB typ
% typ
301
37
Charge Injection
Off Isolation
Channel-to-Channel Crosstalk
Total Harmonic Distortion + Noise (THD + N)
−3 dB Bandwidth
ADG1608
ADG1609
CS (Off)
CD (Off)
ADG1608
ADG1609
CD, CS (On)
ADG1608
ADG1609
POWER REQUIREMENTS
IDD
Unit
1.0
3.3/16
Guaranteed by design, but not subject to production test.
Rev. 0 | Page 5 of 20
VDD = 5.5 V
Digital inputs = 0 V or VDD
ADG1608/ADG1609
3.3 V SINGLE SUPPLY
VDD = 3.3 V, VSS = 0 V, GND = 0 V, unless otherwise noted.
Table 4.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
On-Resistance Match Between Channels (∆RON)
On-Resistance Flatness (RFLAT(ON))
LEAKAGE CURRENTS
Source Off Leakage, IS (Off)
Drain Off Leakage, ID (Off)
ADG1608
ADG1609
Channel On Leakage, ID, IS (On)
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IINL or IINH
25°C
−40°C to
+85°C
−40°C to
+125°C
Unit
13.5
15
0 V to VDD
16.5
V
Ω typ
0.25
5
0.28
5.5
0.3
6.5
Ω typ
Ω typ
±0.5
±3
±2
±1
±14
±7
±2
±14
±0.01
±0.1
±0.01
±0.15
±0.15
±0.01
±0.15
2.0
0.8
±1
±0.1
Digital Input Capacitance, CIN
DYNAMIC CHARACTERISTICS 1
Transition Time, tTRANSITION
tON (EN)
tOFF (EN)
Break-Before-Make Time Delay, tD
4
312
437
216
309
236
316
104
6
−64
−64
0.5
34
72
23
MHz typ
MHz typ
pF typ
145
72
pF typ
pF typ
173
95
pF typ
pF typ
0.001
μA typ
μA max
V min/max
542
331
344
367
411
VS = 0 V to VDD, IS = −10 mA; see Figure 25, VDD = 3.3 V,
VSS = 0 V
VS = 0 V to VDD, IS = −10 mA
VS = 0 V to VDD, IS = −10 mA
VDD = 3.6 V, VSS = 0 V
VS = 0.6 V/3 V, VD = 3 V/0.6 V; see Figure 26
VS = 0.6 V/3 V, VD = 3 V/0.6 V; see Figure 26
VS = VD = 0.6 V or 3 V; see Figure 27
VIN = VGND or VDD
RL = 300 Ω, CL = 35 pF
VS = 1.5 V; see Figure 28
RL = 300 Ω, CL = 35 pF
VS = 1.5 V; see Figure 30
RL = 300 Ω, CL = 35 pF
VS = 1.5 V; see Figure 30
RL = 300 Ω, CL = 35 pF
VS1 = VS2 = 1.5 V; see Figure 29
VS = 1.5 V, RS = 0 Ω, CL = 1 nF; see Figure 31
RL = 50 Ω, CL = 5 pF, f = 100 kHz; see Figure 32
RL = 50 Ω, CL = 5 pF, f = 100 kHz; see Figure 34
RL = 110 Ω, f = 20 Hz to 20 kHz, VS = 2 V p-p; see Figure 35
RL = 50 Ω, CL = 5 pF; see Figure 33
VS = 1.5 V, f = 1 MHz
VS = 1.5 V, f = 1 MHz
VS = 1.5 V, f = 1 MHz
VDD
1
V min
V max
nA typ
μA max
pF typ
ns typ
ns max
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
dB typ
dB typ
% typ
498
48
Charge Injection
Off Isolation
Channel-to-Channel Crosstalk
Total Harmonic Distortion + Noise (THD + N)
−3 dB Bandwidth
ADG1608
ADG1609
CS (Off)
CD (Off)
ADG1608
ADG1609
CD, CS (On)
ADG1608
ADG1609
POWER REQUIREMENTS
IDD
nA typ
nA max
nA typ
nA max
nA max
nA typ
nA max
Test Conditions/Comments
1.0
3.3/16
Guaranteed by design, but not subject to production test.
Rev. 0 | Page 6 of 20
VDD = 3.6 V
Digital inputs = 0 V or VDD
ADG1608/ADG1609
CONTINUOUS CURRENT PER CHANNEL, S OR D
Table 5. ADG1608
Parameter
CONTINUOUS CURRENT, S OR D
VDD = +5 V, VSS = −5 V
TSSOP (θJA = 112.6°C/W)
LFCSP (θJA = 48.7°C/W)
VDD = 12 V, VSS = 0 V
TSSOP (θJA = 112.6°C/W)
LFCSP (θJA = 48.7°C/W)
VDD = 5 V, VSS = 0 V
TSSOP (θJA = 112.6°C/W)
LFCSP (θJA = 48.7°C/W)
VDD = 3.3 V, VSS = 0 V
TSSOP (θJA = 112.6°C/W)
LFCSP (θJA = 48.7°C/W)
25°C
85°C
125°C
Unit
290
470
180
255
100
120
mA max
mA max
213
346
129
185
73
84
mA max
mA max
157
252
101
150
63
77
mA max
mA max
126
206
87
129
56
73.5
mA max
mA max
25°C
85°C
125°C
Unit
147
245
98
147
63
77
mA max
mA max
157
255
101
150
63
77
mA max
mA max
115
189
80
119
52
70
mA max
mA max
94
154
66
101
45
63
mA max
mA max
Table 6. ADG1609
Parameter
CONTINUOUS CURRENT, S OR D
VDD = +5 V, VSS = −5 V
TSSOP (θJA = 112.6°C/W)
LFCSP (θJA = 48.7°C/W)
VDD = 12 V, VSS = 0 V
TSSOP (θJA = 112.6°C/W)
LFCSP (θJA = 48.7°C/W)
VDD = 5 V, VSS = 0 V
TSSOP (θJA = 112.6°C/W)
LFCSP (θJA = 48.7°C/W)
VDD = 3.3 V, VSS = 0 V
TSSOP (θJA = 112.6°C/W)
LFCSP (θJA = 48.7°C/W)
Rev. 0 | Page 7 of 20
ADG1608/ADG1609
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 7.
Parameter
VDD to VSS
VDD to GND
VSS to GND
Analog Inputs 1
Digital Inputs1
Peak Current, S or D
Continuous Current, S or D 2
Operating Temperature Range
Industrial (Y Version)
Storage Temperature Range
Junction Temperature
16-Lead TSSOP, θJA Thermal
Impedance, 0 Airflow
(4-Layer Board)
16-Lead LFCSP, θJA Thermal
Impedance, 0 Airflow
(4-Layer Board)
Reflow Soldering Peak
Temperature, Pb free
1
2
Rating
18 V
−0.3 V to +18 V
+0.3 V to −18 V
VSS − 0.3 V to VDD + 0.3 V or
30 mA, whichever occurs first
GND − 0.3 V to VDD + 0.3 V or
30 mA, whichever occurs first
710 mA (pulsed at 1 ms,
10% duty cycle maximum)
Data + 15%
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
−40°C to +125°C
−65°C to +150°C
150°C
112.6°C/W
48.7°C/W
260°C
Overvoltages at IN, S, or D are clamped by internal diodes. Current should be
limited to the maximum ratings given.
See Table 5 and Table 6.
Rev. 0 | Page 8 of 20
ADG1608/ADG1609
A2
VSS 3
GND
13
TOP VIEW
(Not to Scale)
VDD
12
S5
6
11
S6
S4 7
10
S7
D 8
9
S8
S1
S2 5
S3
10 S5
9 S6
14 A1
NOTES
1. THE EXPOSED PAD IS CONNECTED
INTERNALLY. FOR INCREASED
RELIABILITY OF THE SOLDER
JOINTS AND MAXIMUM THERMAL
CAPABILITY, IT IS RECOMMENDED
THAT THE PAD BE SOLDERED TO
THE SUBSTRATE, VSS.
08318-003
14
ADG1608
4
TOP VIEW
(Not to Scale)
Figure 3. ADG1608 Pin Configuration (TSSOP)
08318-004
15
S3 4
12 GND
11 VDD
S7 8
EN 2
S2 3
S8 7
A1
D 6
16
ADG1608
S4 5
A0 1
13 A2
PIN 1
INDICATOR
VSS 1
S1 2
15 A0
16 EN
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
Figure 4. ADG1608 Pin Configuration (LFCSP)
Table 8. ADG1608 Pin Function Descriptions
Pin No.
TSSOP LFCSP
1
15
2
16
Mnemonic
A0
EN
3
4
5
6
7
8
9
10
11
12
13
14
15
16
N/A
VSS
S1
S2
S3
S4
D
S8
S7
S6
S5
VDD
GND
A2
A1
EP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
EP
Description
Logic Control Input.
Active High Digital Input. When this pin is low, the device is disabled and all switches are off. When this pin
is high, Ax logic inputs determine on switches.
Most Negative Power Supply Potential. In single-supply applications, this pin can be connected to ground.
Source Terminal 1. Can be an input or an output.
Source Terminal 2. Can be an input or an output.
Source Terminal 3. Can be an input or an output.
Source Terminal 4. Can be an input or an output.
Drain Terminal. Can be an input or an output.
Source Terminal 8. Can be an input or an output.
Source Terminal 7. Can be an input or an output.
Source Terminal 6. Can be an input or an output.
Source Terminal 5. Can be an input or an output.
Most Positive Power Supply Potential.
Ground (0 V) Reference.
Logic Control Input.
Logic Control Input.
Exposed Pad. The exposed pad is connected internally. For increased reliability of the solder joints and
maximum thermal capability, it is recommended that the pad be soldered to the substrate, VSS.
Table 9. ADG1608 Truth Table
A2
X1
0
0
0
0
1
1
1
1
1
A1
X1
0
0
1
1
0
0
1
1
A0
X1
0
1
0
1
0
1
0
1
EN
0
1
1
1
1
1
1
1
1
X = don’t care.
Rev. 0 | Page 9 of 20
On Switch
None
1
2
3
4
5
6
7
8
VSS 3
14
VDD
ADG1609
13
TOP VIEW
(Not to Scale)
S1B
12
S2B
S3A 6
11
S3B
S4A 7
10
S4B
DA 8
9
DB
S1A 4
S2A 5
11 S1B
10 S2B
9 S3B
14 A1
NOTES
1. THE EXPOSED PAD IS CONNECTED
INTERNALLY. FOR INCREASED
RELIABILITY OF THE SOLDER
JOINTS AND MAXIMUM THERMAL
CAPABILITY, IT IS RECOMMENDED
THAT THE PAD BE SOLDERED TO
THE SUBSTRATE, VSS.
08318-006
GND
12 VDD
S4B 8
15
SB 7
EN 2
S3A 4
TOP VIEW
(Not to Scale)
DA 6
A1
ADG1609
S4A 5
16
08318-005
A0 1
S2A 3
13 GND
PIN 1
INDICATOR
VSS 1
S1A 2
15 A0
16 EN
ADG1608/ADG1609
Figure 6. ADG1609 Pin Configuration (LFCSP)
Figure 5. ADG1609 Pin Configuration (TSSOP)
Table 10. ADG1609 Pin Function Descriptions
Pin No.
TSSOP LFCSP
1
15
2
16
Mnemonic
A0
EN
3
4
5
6
7
8
9
10
11
12
13
14
15
16
N/A
VSS
S1A
S2A
S3A
S4A
DA
DB
S4B
S3B
S2B
S1B
VDD
GND
A1
EP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
EP
Description
Logic Control Input.
Active High Digital Input. When this pin is low, the device is disabled and all switches are off. When this pin
is high, Ax logic inputs determine on switches.
Most Negative Power Supply Potential. In single-supply applications, this pin can be connected to ground.
Source Terminal 1A. Can be an input or an output.
Source Terminal 2A. Can be an input or an output.
Source Terminal 3A. Can be an input or an output.
Source Terminal 4A. Can be an input or an output.
Drain Terminal A. Can be an input or an output.
Drain Terminal B. Can be an input or an output.
Source Terminal 4B. Can be an input or an output.
Source Terminal 3B. Can be an input or an output.
Source Terminal 2B. Can be an input or an output.
Source Terminal 1B. Can be an input or an output.
Most Positive Power Supply Potential.
Ground (0 V) Reference.
Logic Control Input.
Exposed Pad. The exposed pad is connected internally. For increased reliability of the solder joints and
maximum thermal capability, it is recommended that the pad be soldered to the substrate, VSS.
Table 11. ADG1609 Truth Table
A1
X1
0
0
1
1
1
A0
X1
0
1
0
1
EN
0
1
1
1
1
On Switch Pair
None
1
2
3
4
X = don’t care.
Rev. 0 | Page 10 of 20
ADG1608/ADG1609
TYPICAL PERFORMANCE CHARACTERISTICS
7
7
TA = 25°C
5
VDD = +3.3V
VSS = –3.3V
4
3
VDD = +5V
VSS = –5V
2
VDD = +8V
VSS = –8V
1
5
TA = +125°C
4
TA = +85°C
TA = +25°C
3
TA = –40°C
2
–8
–6
–4
–2
0
2
4
6
8
SOURCE OR DRAIN VOLTAGE (V)
0
0
2
4
6
Figure 7. On Resistance vs. VD (VS) for Dual Supply
10
12
Figure 10. On Resistance vs. VD (VS) for Different Temperatures,
12 V Single Supply
12
16
TA = 25°C
VDD = 3.3V
VSS = 0V
14
10
TA = +125°C
ON RESISTANCE (Ω)
12
ON RESISTANCE (Ω)
8
SOURCE OR DRAIN VOLTAGE (V)
08318-032
1
08318-029
0
VDD = 12V
VSS = 0V
6
ON RESISTANCE (Ω)
ON RESISTANCE (Ω)
6
10
VDD = 5V
VSS = 0V
8
6
VDD = 16V
VSS = 0V
VDD = 12V
VSS = 0V
4
TA = +85°C
8
TA = +25°C
6
TA = –40°C
4
2
2
6
4
8
12
10
14
16
SOURCE OR DRAIN VOLTAGE (V)
0
VDD = +5V
VSS = –5V
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
VDD = 3.3V
VSS = 0V
16
6
14
ON RESISTANCE (Ω)
TA = +125°C
5
TA = +85°C
4
TA = +25°C
3
TA = –40°C
2
12
TA = +125°C
TA = +85°C
TA = +25°C
TA = –40°C
10
8
6
4
0
–4
–3
–2
–1
0
1
2
3
4
5
SOURCE OR DRAIN VOLTAGE (V)
Figure 9. On Resistance vs. VD (VS) for Different Temperatures,
±5 V Dual Supply
0
0.5
1.0
1.5
2.0
2.5
3.0
SOURCE OR DRAIN VOLTAGE (V)
Figure 12. On Resistance vs. VD (VS) for Different Temperatures,
3.3 V Single Supply
Rev. 0 | Page 11 of 20
08318-020
2
1
08318-031
ON RESISTANCE (Ω)
1.0
Figure 11. On Resistance vs. VD (VS) for Different Temperatures,
5 V Single Supply
18
7
0.5
SOURCE OR DRAIN VOLTAGE (V)
Figure 8. On Resistance vs. VD (VS) for Single Supply
0
–5
0
08318-033
2
0
08318-030
0
VDD = 5V
VSS = 0V
ADG1608/ADG1609
9
12
VDD = +5V
VSS = –5V
VBIAS = +4.5V/–4.5V
10
7
LEAKAGE CURRENT (nA)
ID (OFF) – +
ID, IS (ON) + +
IS (OFF) + –
2
0
–2
ID, IS (ON) – –
IS (OFF) – +
ID (OFF) + –
–4
–6
5
3
2
1
0
–1
0
20
40
60
80
100
120
TEMPERATURE (°C)
20
ID, IS (ON) + +
ID (OFF) – +
IS (OFF) + –
IDD (µA)
300
IDD = +5V
ISS = –5V
IDD = +5V
ISS = 0V
ID, IS (ON) – –
IS (OFF) – +
ID (OFF) + –
60
80
100
IDD = +3.3V
ISS = 0V
100
120
TEMPERATURE (°C)
0
08318-034
40
0
2
4
10
12
14
30
25
8
CHARGE INJECTION (pC)
7
6
5
ID, IS (ON) + +
ID (OFF) – +
ID, IS (ON) – –
IS (OFF) + –
IS (OFF) – +
ID (OFF) + –
4
3
2
1
VDD = +12V
VSS = 0V
VDD = +5V
VSS = –5V
20
15
10
VDD = +5V
VSS = 0V
5
20
40
60
80
100
120
TEMPERATURE (°C)
08318-036
0
0
–6
–4
–2
0
2
4
VS (V)
6
8
10
Figure 18. Charge Injection vs. Source Voltage
Figure 15.ADG1608 Leakage Currents vs. Temperature,
5 V Single Supply
Rev. 0 | Page 12 of 20
12
14
08318-026
VDD = +3.3V
VSS = 0V
0
–1
8
Figure 17. IDD vs. Logic Level
VDD = 5V
VSS = 0V
VBIAS = 1V/4.5V
9
6
LOGIC (V)
Figure 14. ADG1608 Leakage Currents vs. Temperature,
12 V Single Supply
10
120
400
200
20
100
IDD = +12V
ISS = 0V
0
0
80
IDD PER CHANNEL
TA = 25°C
500
5
–10
60
600
VDD = 12V
VSS = 0V
VBIAS = 1V/10V
–5
LEAKAGE CURRENT (nA)
40
Figure 16. ADG1608 Leakage Currents vs. Temperature,
3.3 V Single Supply
10
LEAKAGE CURRENT (nA)
0
TEMPERATURE (°C)
Figure 13. ADG1608 Leakage Currents vs. Temperature,
±5 V Dual Supply
15
ID, IS (ON) + +
ID (OFF) – +
ID, IS (ON) – –
IS (OFF) + –
ID (OFF) + –
IS (OFF) – +
4
08318-018
4
6
08318-019
6
08318-035
LEAKAGE CURRENT (nA)
8
–8
VDD = 3.3V
VSS = 0V
VBIAS = 0.6V/3V
8
ADG1608/ADG1609
450
0
TA = 25°C
400
–1
250
200
VDD = +5V, VSS = 0V
150
100
VDD = +5V, VSS = –5V
50
–2
–3
–4
–5
VDD = +12V, VSS = 0V
0
–40
–20
0
20
40
60
80
100
120
TEMPERATURE (°C)
–6
10k
TA = 25°C
VDD = +5V
VSS = –5V
–10
10M
100M
Figure 22. On Response vs. Frequency
0
TA = 25°C
VDD = +5V
VSS = –5V
TA = 25°C
VDD = +5V
VSS = –5V
–20
–20
–30
ACPSRR (dB)
OFF ISOLATION (dB)
1M
FREQUENCY (Hz)
Figure 19. Transition Time vs. Temperature
0
100k
08318-021
INSERTION LOSS (dB)
VDD = +3.3V, VSS = 0V
300
08318-024
TRANSITION TIME (ns)
350
–40
–50
–60
NO DECOUPLING
CAPACITORS
–40
DECOUPLING
CAPACITORS
–60
–80
–70
–80
–100
100k
1M
10M
100M
1G
FREQUENCY (Hz)
–120
08318-023
–100
10k
1k
Figure 20. Off Isolation vs. Frequency
0
–10
10k
100k
1M
FREQUENCY (Hz)
10M
100M
08318-027
–90
Figure 23. ACPSRR vs. Frequency
0.6
TA = 25°C
VDD = +5V
VSS = –5V
LOAD = 110Ω
TA = 25°C
0.5
–20
VDD = +3.3V, VS = 2V p-p
0.4
THD + N (%)
–40
–50
–60
0.3
VDD = +5V, VS = 3.5V p-p
0.2
–70
–80
VDD = +5V, VSS = –5V, VS = 5V p-p
0.1
–90
100k
1M
10M
100M
FREQUENCY (Hz)
1G
Figure 21. Crosstalk vs. Frequency
0
0
5k
10k
FREQUENCY (Hz)
15k
Figure 24. THD + N vs. Frequency
Rev. 0 | Page 13 of 20
20k
08318-028
–100
10k
VDD = +12V, VS = 5V p-p
08318-022
CROSSTALK (dB)
–30
ADG1608/ADG1609
TEST CIRCUITS
V
IS (OFF)
D
A
IDS
D
ID (OFF)
VS
08318-007
VS
S
A
VD
Figure 25. On Resistance
08318-008
S
Figure 26. Off Leakage
ID (ON)
D
NC = NO CONNECT
A
VD
08318-009
S
NC
Figure 27. On Leakage
3V
ADDRESS
DRIVE (VIN)
50%
50%
tr < 20ns
tf < 20ns
VDD
VSS
VDD
VSS
A0
0V
VIN
S1
A1
50Ω
A2
tTRANSITION
VS1
S2 TO S7
tTRANSITION
VS8
S8
90%
ADG1608*
2.4V
OUTPUT
OUTPUT
D
EN
100Ω
GND
35pF
08318-010
90%
*SIMILAR CONNECTION FOR ADG1609.
Figure 28. Address to Output Switching Times, tTRANSITION
3V
ADDRESS
DRIVE (VIN)
VDD
VSS
VDD
VSS
A0
VIN
0V
S1
A1
50Ω
A2
VS
S2 TO S7
S8
80%
ADG1608*
80%
OUTPUT
2.4V
OUTPUT
D
EN
GND
100Ω
35pF
*SIMILAR CONNECTION FOR ADG1609.
Figure 29. Break-Before-Make Delay, tBBM
Rev. 0 | Page 14 of 20
08318-011
tBBM
ADG1608/ADG1609
3V
50%
VSS
VDD
VSS
A0
50%
S1
A1
0V
A2
tON (EN)
ADG1608*
tOFF (EN)
0.9VO
0.9VO
OUTPUT
50Ω
OUTPUT
D
EN
VIN
VS
S2 TO S8
35pF
100Ω
GND
08318-012
ENABLE
DRIVE (VIN)
VDD
*SIMILAR CONNECTION FOR ADG1609.
Figure 30. Enable Delay, tON (EN), tOFF (EN)
3V
VDD
VSS
VDD
VSS
A0
A1
VIN
A2
ADG1608*
ΔVOUT
QINJ = CL × ΔVOUT
S
D
EN
VS
GND
VOUT
CL
1nF
VIN
*SIMILAR CONNECTION FOR ADG1609.
Figure 31. Charge Injection
Rev. 0 | Page 15 of 20
08318-013
VOUT
RS
ADG1608/ADG1609
VDD
VSS
VDD
NETWORK
ANALYZER
NETWORK
ANALYZER
VSS
S
VOUT
D
VS
S2
GND
VOUT
GND
OFF ISOLATION = 20 log
VOUT
VS
CHANNEL-TO-CHANNEL CROSSTALK = 20 log
Figure 32. Off Isolation
VDD
0.1µF
VSS
0.1µF
0.1µF
NETWORK
ANALYZER
VSS
VOUT
VS
Figure 34. Channel-to-Channel Crosstalk
VSS
VDD
R
50Ω
VS
08318-014
RL
50Ω
VSS
S1
D
VDD
0.1µF
VDD
RL
50Ω
50Ω
50Ω
0.1µF
VSS
0.1µF
0.1µF
08318-015
VDD
0.1µF
VDD
AUDIO PRECISION
VSS
RS
S
S
50Ω
IN
VS
D
VS
V p-p
D
INSERTION LOSS = 20 log
VOUT WITH SWITCH
VOUT WITHOUT SWITCH
VIN
GND
RL
10kΩ
Figure 35. THD + Noise
Figure 33. Bandwidth
Rev. 0 | Page 16 of 20
VOUT
08318-017
GND
VOUT
08318-016
RL
50Ω
ADG1608/ADG1609
TERMINOLOGY
IDD
The positive supply current.
CIN
The digital input capacitance.
ISS
The negative supply current.
tTRANSITION
The delay time between the 50% and 90% points of the digital
input and switch on condition when switching from one address
state to another.
VD (VS)
The analog voltage on Terminal D and Terminal S.
RON
The ohmic resistance between Terminal D and Terminal S.
RFLAT(ON)
Flatness that is defined as the difference between the maximum
and minimum value of on resistance measured over the specified
analog signal range.
tON (EN)
The delay between applying the digital control input and the
output switching on.
tOFF (EN)
The delay between applying the digital control input and the
output switching off .
Charge Injection
A measure of the glitch impulse transferred from the digital
input to the analog output during switching.
IS (Off)
The source leakage current with the switch off.
ID (Off)
The drain leakage current with the switch off.
Off Isolation
A measure of unwanted signal coupling through an off switch.
ID, IS (On)
The channel leakage current with the switch on.
Crosstalk
A measure of unwanted signal that is coupled through from one
channel to another as a result of parasitic capacitance.
VINL
The maximum input voltage for Logic 0.
Bandwidth
The frequency at which the output is attenuated by 3 dB.
VINH
The minimum input voltage for Logic 1.
On Response
The frequency response of the on switch.
IINL (IINH)
The input current of the digital input.
Insertion Loss
The loss due to the on resistance of the switch.
CS (Off)
The off switch source capacitance, which is measured with
reference to ground.
Total Harmonic Distortion + Noise (THD + N)
The ratio of the harmonic amplitude plus noise of the signal to
the fundamental.
CD (Off)
The off switch drain capacitance, which is measured with
reference to ground.
CD, CS (On)
The on switch capacitance, which is measured with reference to
ground.
AC Power Supply Rejection Ratio (ACPSRR)
The ratio of the amplitude of signal on the output to the amplitude
of the modulation. This is a measure of the ability of the part to
avoid coupling noise and spurious signals that appear on the supply
voltage pin to the output of the switch. The dc voltage on the device
is modulated by a sine wave of 0.62 V p-p.
Rev. 0 | Page 17 of 20
ADG1608/ADG1609
OUTLINE DIMENSIONS
5.10
5.00
4.90
16
9
4.50
4.40
4.30
6.40
BSC
1
8
PIN 1
1.20
MAX
0.15
0.05
0.30
0.19
0.65
BSC
COPLANARITY
0.10
0.20
0.09
0.75
0.60
0.45
8°
0°
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-153-AB
Figure 36. 16-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-16)
Dimensions shown in millimeters
PIN 1
INDICATOR
0.30
0.23
0.18
0.50
BSC
13
PIN 1
INDICATOR
16
1
12
1.75
1.60 SQ
1.55
EXPOSED
PAD
9
TOP VIEW
0.80
0.75
0.70
0.50
0.40
0.30
4
8
BOTTOM VIEW
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
5
0.20 MIN
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-WEED.
070209-C
3.10
3.00 SQ
2.90
Figure 37. 16-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
3 mm x 3 mm Body, Very Very Thin Quad
(CP-16-22)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADG1608BRUZ 1
ADG1608BRUZ-REEL71
ADG1608BCPZ-REEL71
ADG1609BRUZ1
ADG1609BRUZ-REEL71
ADG1609BCPZ-REEL71
1
Temperature Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Package Description
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
Z = RoHS Compliant Part.
Rev. 0 | Page 18 of 20
Package
Option
RU-16
RU-16
CP-16-22
RU-16
RU-16
CP-16-22
Branding
S38
S39
ADG1608/ADG1609
NOTES
Rev. 0 | Page 19 of 20
ADG1608/ADG1609
NOTES
©2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D08318-0-7/09(0)
Rev. 0 | Page 20 of 20
Similar pages