A2SI-E Advanced AS-Interface IC Features Description • • • A²SI-E is a monolithic CMOS integrated circuit certified for AS-i (Actuator Sensor-interface) networks. AS-i networks are intended for industrial automation. • • • • • • • AS-i Complete Specification V2.11 compliant Integrated EEPROM Additional addressing channel using an optoelectronic interface Extended address mode operation as programmable option (up to 62 slaves) High impedance AS-i line input, additional pins for further impedance optimizations DC voltage output, approximately 24 volts, not stabilized 5 volt DC voltage output, stabilized, CMOS logic can be supplied directly (e.g. µC) LED status indicator output (compliant with the standard indication recommendation) Integrated watchdog Temperature range -25°C to + 105°C The main advantage of AS-i solutions is that actuators and sensors are connected using a twowire unshielded cable that is easy to install. This cable transports both power and information/data. AS-i network communication is based on the master-slave principle. The network can be extended (to cable lengths greater than 100m) by using the A²SI-E in the repeater mode configuration. Furthermore, the A²SI-E is used as slave interface to sensors / actuators and as master interface. AS-i is a standard for the automation industry based on IEC 62026-2 and EN 50295. The device is available in a 28-pin SOP (300 mils) package. Block Diagram 2.2 µF 5V 24V 8 MHz 10 µF UIN CAP RCAP A2SI-E UOUT U5R ELECTRONIC INDUCTOR U5RD POWER SUPPLY OSC1/2 OSCILLATOR CCAP POWERFAIL DETECTION ASI+ 4 DOx RECEIVE 4 ASIP DIGITAL LOGIC ASI– DIx DSR ASIN PST TRANSMIT 4 Px THERMAL PROTECTION GND2 0V GND1 GND IRD AMP IRD LED FID Copyright © 2002, ZMD AG Data Sheet, Rev. 1.2, October 21, 2002 Printed in Germany, All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The Information furnished in this publication is preliminary and subject to changes without notice. A2SI-E Advanced AS-Interface IC Application The A²SI-E is packaged in 28-pin SOP, which exhibits a lower thermal resistance than the 28-pin SSOP package of A²SI IC. Besides applications that require higher operating ambient temperature than possible with A²SI, A²SI-E accommodates applications which require a higher power dissipation of the integrated circuit. The thermal resistance of the SOP package of the A²SI-E integrated circuit is ideal for master and/or repeater applications. Ordering Information Ordering Code Description Operating Temperature Range Package Type Device Marking Shipping Form A2SI-E-ST Standard version of A²SI-E -25°C to 105°C 28-pin SOP (300 mils) A²SI-E Tubes (27 parts/tube) A2SI-E-SR Standard version of A²SI-E -25°C to 105°C 28-pin SOP (300 mils) A²SI-E Tape-and-Reel (1000 parts/reel) A2SI-E-MT Pre-programmed master function -25°C to 105°C 28-pin SOP (300 mils) A²SI-E + yellow dot Tubes (27 parts/tube) A2SI-E-MR Pre-programmed master function -25°C to 105°C 28-pin SOP (300 mils) A²SI-E + yellow dot Tape-and-Reel (1000 parts/reel) ZMD Stuttgart Office For further Nord-West-Ring 34 information: 70974 Filderstadt- Bernhausen Tel.: +49 (0)711.674.517-0 Fax: +49 (0)711.674.517-99 [email protected] ZMD AG Grenzstrasse 28 01109 Dresden, Germany Tel.: +49 (0)351.8822.310 Fax: +49 (0)351.8822.337 [email protected] ZMD America Inc. 201 Old Country Road, Ste 204 Melville, NY 11747 Tel.: (631) 549-2666 Fax: (631) 549-2882 [email protected] Copyright © 2002, ZMD AG Data Sheet, Rev. 1.2, October 21, 2002 Printed in Germany, All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The Information furnished in this publication is preliminary and subject to changes without notice.