DATA SHEET CLL130-0101A5-40AM1B1 and are trademarks or registered trademarks of CITIZEN HOLDINGS CO., LTD. JAPAN. is a trademark or a registered trademark of CITIZEN ELECTRONICS CO., LTD. JAPAN. Ref.CE-P2153 09/12 DATA SHEET 1/13 1. Scope of Application These data sheet are applied to the chip type LED lamp , model CLL130-0101A5-40AM1B1 2. Part code CLL130-0101A5-40AM1B1 [1] [2] [3] [4] [5] [6] [7] [1]Series CLL : LED for general lighting [2]Outline dimensions 130 : 2.0(L) x 1.6(W) x 0.75(H) [3]Dies in series quantity 01 : 1 [4]Dies in parallel quantity 01 : 1 [5]Correlated color temperature 40 : 4000K [6]Chromaticity range A : ANSI C78,377-2008 [7]CRI M1 : Ra Min 80 Type Symbol CITILED Name CLL130-0101A5-40AM1B1 CITIZEN ELECTRONICS CO.,LTD. JAPAN Ref.CE-P2153 09/12 DATA SHEET 2/13 3. Outline drawing Unit ：mm Tolerance ：±0.1mm 4. Performance ( 1 ) Absolute Maximum Rating Parameter Symbol Raiting Value Unit Power Dissipation PD 292 mW Forward Current IF 85 mA Forward Pulse Current IFP 100 mA Minimum current IF min 5 mA Reverse Current IR 1 mA Operating Temperature T OP -30 ～ +85 C Storage Temperature T ST -40 ～ +100 C 120 C Junction Temperature Tj Max *1 *2 *1 Forward Current : Duty<=1/10 , Pulse Width<=10msec *2 D.C. Current : Tj = Ts + Rj-s × PD Pulse Current : Tj = Ts + Rj-s × Pw(Power Dissipation / One-Pulse) × Duty *Ts : Solder terminal(Anode)temperature Symbol CITILED Name CLL130-0101A5-40AM1B1 CITIZEN ELECTRONICS CO.,LTD. JAPAN Ref.CE-P2153 09/12 DATA SHEET ( 2 ) Electro-optical Characteristics Parameter Symbol Condition IF =50mA Forward Voltage VF *1 Junction-solder Thermal Resistance Rj-s IF =50mA Luminous Flux Φv General Color Rendering Index IF =50mA Ra Min. 2.65 14.7 80 3/13 Typ. 2.95 45 18.4 - Tｓ=25C Unit V C/W lm - Max. 3.25 22.2 - *1 Thermal Resistance : Junction - Solder terminal (Anode) Ranking (Condition : IF=50mA , Ts=25C) Parameter Symbol Forward Voltage VF Luminous Flux Φv Rank Q R S C D Min. 2.65 2.90 3.10 14.7 18.4 Max. 2.90 3.10 3.30 18.4 22.2 0 0 x 0.4006 0.3871 0.3828 0.3952 0.4006 x 0.3952 0.3828 0.3784 0.3898 y 0.4044 0.3959 0.3803 0.3880 0.4044 y 0.3880 0.3803 0.3647 0.3716 Unit V lm Chromaticity coordinates ( Condition : IF=50mA ,Ts=25C) Color Rank 1 Color Rank 3 x 0.3871 0.3736 0.3703 0.3828 0.3871 x 0.3828 0.3703 0.3670 0.3784 y 0.3959 0.3874 0.3726 0.3803 0.3959 y 0.3803 0.3726 0.3578 0.3647 Color Rank 2 Color Rank 4 *1 The tolerance of measurement at our tester is VF±3% , Φv±7% , Chromaticity(x,y)±0.01 *For an order, products within the rank listed above will be delivered. Except designation of a delivery proportion of each rank. Symbol CITILED Name CLL130-0101A5-40AM1B1 CITIZEN ELECTRONICS CO.,LTD. JAPAN Ref.CE-P2153 09/12 DATA SHEET 4/13 x, y Chromaticity 0.41 0.40 2 y 0.39 1 0.38 4 0.37 3 0.36 0.35 0.36 0.37 0.38 0.39 0.40 0.41 x Symbol CITILED Name CLL130-0101A5-40AM1B1 CITIZEN ELECTRONICS CO.,LTD. JAPAN Ref.CE-P2153 09/12 DATA SHEET 5/13 5. Characteristics ・Forward Current vs. Forward Voltage ・Forward Current vs. Relative Luminous Intensity Ts=25C 3.1 VF [V] 3.0 2.9 2.8 2.7 2.6 2.5 2.4 0 20 40 60 IF [mA] 80 120% 100% 80% 60% 40% 20% 0% 40 60 IF [mA] 80 100 IF=50mA 0.020 0.015 ⊿x 0.015 ⊿x 0.010 ⊿y 0.010 ⊿y 0.005 0.000 -0.005 0.005 0.000 -0.005 -0.010 -0.010 -0.015 -0.015 -0.020 -0.020 0 20 40 60 IF [mA] 80 100 ・Solder Temperature vs. Forward Voltage 0 Relative Luminous Intensity [a.u.] 3.0 2.9 2.8 2.7 2.6 0 20 40 60 80 20 40 60 Ts [C] 80 100 ・Solder Temperature vs. Relative Luminous Intensity IF=50mA 3.1 VF [V] 20 ・Solder Temperature vs. Chromaticity Coordinate ⊿x,⊿y ⊿x,⊿y 140% 0 Ts=25C 0.020 160% 100 ・Forward Current vs. Chromaticity Coordinate Ts=25C 180% Relative Luminous Intensity [a.u.] 3.2 100 IF=50mA 120% 100% 80% 60% 40% 20% 0% 0 Ts [C] 20 40 60 Ts [C] 80 100 Symbol CITILED Name CLL130-0101A5-40AM1B1 CITIZEN ELECTRONICS CO.,LTD. JAPAN Ref.CE-P2153 09/12 DATA SHEET 6/13 ・Solder Temperature vs. Allowable Forward Current Relative Emission Intensity [a.u.] 90 80 70 IF [ｍA] ・Spectrum 60 50 40 30 20 10 0 0 25 50 75 100 Ts [C] 125 150 IF=50mA, Ts=25C 120% 100% 80% 60% 40% 20% 0% 350 450 550 650 750 850 λ [nm] ・Directive Characteristic IF=50mA Ts=25℃ -40° -30° -50° -20° -10° 100% 10° 20° 30° 40° 50° 80% -60° 60% -70° 40% -80° 20% 80° -90° 0% 90° θ=0 θ 60° 70° IF=50mA Ts=25℃ -40° -50° -30° -20° -10° 100% 10° 20° 30° 40° 50° 80% θ=0 -60° 60% 60° -70° 40% 70° -80° 20% 80° -90° 0% 90° θ LED chip is mounted on White color PCB. Symbol CITILED Name CLL130-0101A5-40AM1B1 CITIZEN ELECTRONICS CO.,LTD. JAPAN Ref.CE-P2153 09/12 DATA SHEET 7/13 6. Reliability (1) Details of the tests Test Item Continuous Operation Test Test Condition Ta=60C, IF=50mA , 1000 hours(with Al-fin) Ta=85C, IF=50mA , 1000 hours(with Al-fin) Low Temperature Storage Test Ta=-40C , 1000 hours High Temperature Storage Test Ta=100C, 1000 hours Moisture-proof Test Ta=60C, 90%RH, 1000 hours Thermal Shock Test Ta=-40C 30minutes～100C 30minuets, 100cycle (2) Judgment Criteria of Failure for Reliability Test Ta=25C Measuring Item Symbol Measuring Condition Judgment Criteria for Failure IF =50mA Forward Voltage VF > U×1.2 IF =50mA Luminous Flux < S×0.7 Φv U defines the upper limit of the specified characteristics. S defines the initial value. Note : Measurement shall be taken between 2 hours and 24 hours, and the test pieces should be return to the normal ambient conditions after the completion of each test. Symbol CITILED Name CLL130-0101A5-40AM1B1 CITIZEN ELECTRONICS CO.,LTD. JAPAN Ref.CE-P2153 09/12 DATA SHEET 8/13 7. Taping Specifications (in accordance with JIS standard) (1) Shape and Dimensions of Reel 21 ±0.8 (Unit: mm) 13 ±0.5 +1 0 0 3 60 1 80 - 2 ±0.5 Name. Qty Lot No. 9 ±0.3 11.4 ±1.0 (Unit: mm) 3 .5 0 ±0 .0 5 1.5-+0.1 0 (2 .2 4 ) (1) 8 ±0 .2 1 .7 5 ±0 .1 (2) Dimensions of Tape (2) (1) (1.84) 0.25 ±0.05 (0.9) 2 ±0.05 ( 1.0) (2) Polarity 4 ±0.1 4 ±0.1 Progressive direction (3) Configuration of Tape (END) more than 40mm Mounted with CITILED (START) Leading part more than 400mm Unloaded tape (4) Quantity: 2500pcs/reel Symbol CITILED Name CLL130-0101A5-40AM1B1 CITIZEN ELECTRONICS CO.,LTD. JAPAN Ref.CE-P2153 09/12 DATA SHEET 9/13 8. Packing Specifications 8-1. Moisture-proof Packing To prevent moisture absorption during transportation and storage, reels are packed in aluminum envelopes which contain a desiccant. Aluminum envelop Reel Desiccant Polyester Zip fastener Label 8-2. Storage To prevent moisture absorption, it is strongly recommended that reels (in bulk or taped) should be stored in the dry box (or the desiccator) with a desiccant as the appropriate storage place. If not, the following is recommended. Temperature : Humidity : 5~30C 60%RH max. The devices should be mounted as soon as possible after unpacking. If you store the unpacked reels, please store them in the dry box or seal them into the envelop again. Moisture Sensitive Level 1. (IPC/JEDEC J-STD-020C) Symbol CITILED Name CLL130-0101A5-40AM1B1 CITIZEN ELECTRONICS CO.,LTD. JAPAN Ref.CE-P2153 09/12 DATA SHEET 10/13 9. Precautions 9-1. Soldering (1) Lead free soldering 1) Following soldering paste is recommended Melting temperature : 216 ~ 220C. Composition : Sn 3.5Ag 0.75Cu 2) The temperature profile at the top surface of the parts is recommended as shown below. T em p e ra tu re 3) It is requested that products should be handled after their temperature has dropped down to the normal room temperature 4 °C/sec. Max 4 °C/sec. Max 220 °C 160 ~ 180 °C 140sec 260 °C Max 3sec. Max 60 ~ 70sec Time 9-2. Washing (1) When washing after soldering is needed, following conditions are requested. a) Washing solvent: Pure Water b) Temperature, time: 50C or less × 30 seconds max or 30C or less × 3 minutes max. Symbol CITILED Name CLL130-0101A5-40AM1B1 CITIZEN ELECTRONICS CO.,LTD. JAPAN Ref.CE-P2153 09/12 DATA SHEET 11/13 9-3. Eye Safety - The International Electrical Commission (IEC) published in 2006 IEC 62471 ”2006 Photobiological safety oflamps and lamp systems ” which includes LEDs within its scope. When sorting single LEDs according to IEC 62471, most LEDs can be classified as belonging to either Exempt Group or Risk Group 1. - Optical characteristics of LEDs such as radiant flux, spectrum and light distribution are factors that affect the risk group determination of the LED, and especially a high-power LED, that emits light containing blue wavelengths, may have properties equivalent to those of Risk Group 2. - Great care should be taken when directly viewing an LED that is driven at high current, has multiple uses as a module or when focusing the light with optical instruments, as these actions may greatly increase the hazard to your eyes. - In addition, LED sources that were included within the scope of IEC 60825-1 / Edition 1.2 “laser safety standard”, published 2001 were removed from the scope of the IEC 60825-1 / Edition 2.0 revised 2007. - However, keep in mind that some countries and regions have adopted standards based on the IEC laser safety standard IEC 60825-1:2001 which includes LEDs within its scope. 9-4. Other directions (1) It is requested to avoid any stress added to the resin portion while it is heated. (2) It is requested to avoid any friction by sharp metal nail etc. to the resin portion. (3) If the product might to be used under the following conditions, the customer must evaluate its appropriateness them. This product is not designed for use under the following conditions. in places where the product might: - get wet due to rain - suffer from damage caused by salt. - be exposed to corrosive gas such as Cl, H2S, NH3, SO2, NOx and so on. - be exposed to dust, fluid or oil. Symbol CITILED Name CLL130-0101A5-40AM1B1 CITIZEN ELECTRONICS CO.,LTD. JAPAN Ref.CE-P2153 09/12 DATA SHEET 12/13 10. Designing precautions 1. The current limiting resistor should be placed in the circuit so that is driven within its rating. Also avoid reverse voltage (over-current) applied instantaneously when ON or OFF. 2. When pulse driving current is applied, average current consumption should be within the rating. Also avoid reverse voltage applied when put off. 3. Recommended soldering pattern < For reflow soldering > Anode Pad Outline Center Cathode Pad Unit : mm Mountability and solderability need to be optimized with actual conditions such as amount of solder, reflow temperature applied in the process. 4. When assembling the circuit board into the finished products, care must be taken to avoid the component parts from touching other parts. 5. When using multiple LEDs, it is required to connect a current limiting resistor on each path which the current flows to the LEDs. (ex-1) (ex-2) (ex-3) R R R R R R R 6. Other This product complies with RoHS directives. Symbol CITILED Name CLL130-0101A5-40AM1B1 CITIZEN ELECTRONICS CO.,LTD. JAPAN Ref.CE-P2153 09/12 DATA SHEET 13/13 11. Precautions with regard to product use 1. This document is provided for reference purposes only so that CITIZEN ELECTRONICS' products are used as intended. CITIZEN ELECTRONICS neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any any other rights of CITIZEN ELECTRONICS or any third party with respect to the information in this document. 2. All information included in this document such as product data, diagrams, charts, is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any CITIZEN ELECTRONICS' products listed in this document, please confirm the latest product information with a CITIZEN ELECTRONICS' sales office, and formal specifications must be exchanged and signed by both parties prior to mass production. 3. CITIZEN ELECTRONICS has used reasonable care in compiling the information included in this document, but CITIZEN ELECTRONICS assumes no liability whatsoever for any damages incurred as a result of errors or omissions in the information included in this document. 4. Absent ａ written signed agreement, except as provided in the relevant terms and conditions of sale for product, and to the maximum extent allowable by law, CITIZEN ELECTRONICS assumes no liability whatsoever, including without limitation, indirect, consequential, special, or incidental damages or loss, including without limitation, loss of profits, loss of opportunities, business interruption and loss of data, and disclaims any and all express or implied warranties and conditions related to sale, use of product, or information, including warranties or conditions of merchantability, fitness for a particular purpose, accuracy of information, or no infringement. 5. Though CITIZEN ELECTRONICS works continually to improve products' quality and reliability, products can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards to minimize risk and avoid situations in which a malfunction or failure of a product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. In addition, customers are also responsible for determining the appropriateness of use of any information contained in this document such as application cases not only with evaluating by their own but also by the entire system. CITIZEN ELECTRONICS assumes no liability for customers' product design or applications. 6. Please contact CITIZEN ELECTRONICS' sales office if you have any questions regarding the information contained in this document, or if you have any other inquiries. Symbol CITILED Name CLL130-0101A5-40AM1B1 CITIZEN ELECTRONICS CO.,LTD. JAPAN Ref.CE-P2153 09/12