LH28F008SA FEATURES 8M (1M × 8) Flash Memory 40-PIN TSOP TOP VIEW • Very High-Performance Read – 85 ns Maximum Access Time • High-Density Symmetrically Blocked Architecture – Sixteen 64K Blocks • Extended Cycling Capability – 100,000 Block Erase Cycles – 1.6 Million Block Erase Cycles per Chip • Automated Byte Write and Block Erase – Command User Interface – Status Register • System Performance Enhancements – RY /» BY » Status Output – Erase Suspend Capability • Deep-Powerdown Mode – 0.20 µA ICC Typical • SRAM-Compatible Write Interface • Hardware Data Protection Feature – Erase/Write Lockout during Power Transitions • Independent Software Vendor Support A19 1 40 NC A18 2 39 NC A17 3 38 WE A16 4 37 OE A15 5 36 RY/BY A14 6 35 DQ7 A13 7 34 DQ6 A12 8 33 DQ5 CE 9 32 DQ4 VCC 10 31 VCC VPP 11 30 GND PWD 12 29 GND A11 13 28 DQ3 A10 14 27 DQ2 A9 15 26 DQ1 A8 16 25 DQ0 A7 17 24 A0 A6 18 23 A1 A5 19 22 A2 A4 20 21 A3 28F008SA-1 Figure 1. 40-Pin TSOP Configuration – Microsoft Flash File System™ (FFS) • ETOX™ Nonvolatile Flash Technology – 12 V Byte Write/Block Erase • Industry Standard Packaging – 40-Pin 1.2 mm × 10 mm × 20 mm TSOP (Type I) Package – 44-Pin 600-mil SOP Package 1 LH28F008SA 8M (1M × 8) Flash Memory 44-PIN SOP TOP VIEW VPP 1 44 VCC RP 2 43 CE A11 3 42 A12 A10 4 41 A13 A9 5 40 A14 A8 6 39 A15 A7 7 38 A16 A6 8 37 A17 A5 9 36 A18 A4 10 35 A19 NC 11 34 NC NC 12 33 NC A3 13 32 NC A2 14 31 NC A1 15 30 WE A0 16 29 OE DQ0 17 28 RY/BY DQ1 18 27 DQ7 DQ2 19 26 DQ6 DQ3 20 25 DQ5 GND 21 24 DQ4 GND 22 23 VCC SHARP’s LH28F008SA employs advanced CMOS circuitry for systems requiring low power consumption and noise immunity. Its 85 ns access time provides superior performance when compared with magnetic storage media. A deep powerdown mode lowers power consumption to 1 µW typical through VCC, crucial in portable computing, handheld instrumentation and other low-power applications. The PWD power control input also provides absolute data protection during system power up/down. DESCRIPTION 28F008SA-16 Figure 2. 44-Pin SOP Configuration INTRODUCTION SHARP’S LH28F008SA 8M Flash File™ Memory is the highest density nonvolatile read/write solution for solid state storage. The LH28F008SA’s extended cycling, symmetrically blocked architecture, fast access time, write automation and low power consumption provide a more reliable, lower power, lighter weight and higher performance alternative to traditional rotating disk technology. The LH28F008SA brings new capabilities to portable computing. Application and operating system software stored in resident flash memory arrays provide instant-on rapid execute-in-place and protection from obsolescence through in-system software updates. Resident software also extends system battery life and increases relaibility by reducing disk drive accesses. For high density data acquisition applications, the LH28F008SA offers a more cost-effective and reliable alternative to SRAM and battery. Traditional high density embedded applications, such as telecommunications, can take advantage of the LH28F008SA’s nonvolatility, blocking and minimal system code requirements for flexible firmware and modular software designs. 2 The LH28F008SA is offered in 40-pin TSOP (standard) package. Pin assignments simplify board layout when integrating multiple devices in a flash memory array or subsystem. This device uses an integrated Command User Interface and state machine for simplified block erasure and byte write. The LH28F008SA memory map consists of 16 separately erasable 64K blocks. The LH28F008SA is a high-performance 8M (8,388,608 bit) memory organized at 1M (1,048,576 bytes) of 8 bits each. Sixteen 64K (65,536 Byte) blocks are included on the LH28F008SA. A memory map is shown in Figure 4 of this specification. A block erase operation erases one of the sixteen blocks of memory in typically 1.6 seconds, independent of the remaining blocks. Each block can be independently erased and written 100,000 cyles. Erase Suspend mode allows system software to suspend block erase to read data or execute code from any other block of the LH28F008SA. The LH28F008SA is available in the 40-pin TSOP (Thin Small Outline Package, 1.2 mm thick) package. Pinouts are shown in Figure 1 of this specification. The Command User Interface serves as the interface between the microprocessor or microcontroller and the internal operation of the LH28F008SA. Byte Write and Block Erase Automation allow byte write and block erase operations to be executed using a two-write command sequence to the Command User Interface. The internal Write State Machine (WSM) automatically executes the algorithms and timings necessary for byte write and block erase operations, including verifications, thereby unburdening the microprocessor or microcontroller. Writing of memory data is performed in byte increments typically within 9 µs, an 80% improvement over current flash memory products. IPP byte write and block erase currents are 10 mA typical, 30 mA maximum. VPP byte write and block erase voltage is 11.4 V to 12.5 V. The Status Register indicates the status of the WSM and when the WSM successfully completes the desired byte write or block erase operation. 8M (1M × 8) Flash Memory LH28F008SA DQ0 - DQ7 OUTPUT BUFFER INPUT BUFFER IDENTIFIER REGISTER OUTPUT MULTIPLEXER STATUS REGISTER I/O LOGIC DATA REGISTER DATA COMPARATOR A0 - A19 Y-GATING INPUT BUFFER COMMAND USER INTERFACE WRITE STATE MACHINE CE WE OE PWD RY/BY Y-DECODER X-DECODER ... ADDRESS LATCH 16 64KB BLOCKS ADDRESS COUNTER PROGRAM/ ERASE VOLTAGE SWITCH VPP VCC GND 28F008SA-2 Figure 3. LH28F008SA Block Diagram 3 LH28F008SA 8M (1M × 8) Flash Memory PIN DESCRIPTION SYMBOL TYPE INPUT ADDRESS INPUTS: For memory addresses. Addresses are internally latched during a write cycle. INPUT/OUTPUT DATA INPUT/OUTPUTS: Inputs data and commands during Command User Interface write cycles; outputs data during memory array. Status Register and Identifier read cycles. The data pins are active high and float to tri-state off when the chip is deselected or the outputs are disabled. Data is internally latched during a write cycle. CE » INPUT CHIP ENABLE: Activates the device’s control logic input buffers, decoders, and sense amplifiers. CE » is active low: CE » high deselects the memory device and reduces power consumption to standby levels. PWD INPUT POWERDOWN: Puts the device in deep powerdown mode. PWD is active low; PWD high gates normal operation. PWD also locks out block erase or byte write operations when active low, providing data protection during power transitions. OE » INPUT OUTPUT ENABLE: Gates the device’s outputs through the data buffers during a read cycle. OE » is active low. WE INPUT WRITE ENABLE: Controls writes to the Command User Interface and array blocks. WE is active low. Addresses and data are latched on the rising edge of the WE Pulse. RY /» BY » OUTPUT READY/BUSY: Indicates the status of the internal Write State Machine. When low, it indicates that the WSM is performing a block erase or byte write operation. RY/» BY » high indicates that the WSM is ready for new commands, block erase is suspended or the device is in deep powerdown mode. RY »/BY i» s always active and does NOT float to tri-state off when the chip is deselected or data outputs are disabled. VPP SUPPLY BLOCK ERASE/BYTE WRITE POWER SUPPLY: for erasing blocks of the array or writing bytes of each block. NOTE: With VPP < VPPLMAX, memory contents cannot be altered. A0 - A19 DQ0 - DQ7 DEVICE POWER SUPPLY: (5 V ±10%, 5 V ±5%) VCC GND 4 NAME AND FUNCTION SUPPLY GROUND 8M (1M × 8) Flash Memory LH28F008SA The RY »/BY » output gives an additional indicator of WSM activity, providing capability for both hardware signal of status (versus software polling) and status masking (interrupt masking for background erase, for example). Status polling using RY »/BY » minimizes both CPU overhead and system power consumption. When low, RY /» BY » indicates that the WSM is performing a block erase or byte write operation. RY /» BY » high indicates that the WSM is ready for new commands, block erase is suspended or the device is in deep power down mode. MEMORY MAP Maximum access time is 85 ns (tACC) over the commercial temperature range (0°C to +70°C) and over VCC supply voltage range (4.5 V to 5.5 V and 4.75 V to 5.25 V). ICC active current (CMOS Read) is 20 mA typical, 35 mA maximum at 8 MHz. C0000 BFFFF When the CE » and PWD pins are at VCC, the ICC CMOS Standby mode is enabled. 90000 8FFFF A Deep Powerdown mode is enabled when the PWD pin is at GND, minimizing power consumption and providing write protection. ICC current in deep power down is 0.20 µA typical. Reset time of 400 ns is required from PWD switching high until outputs are valid to read attempts. Equivalently, the device has a wake time of 1 µs from PWD high until writes to the Command User Interface are recognized by the LH28F008SA. With PWD at GND, the WSM is reset and the Status Register is cleared. FFFFF F0000 EFFFF E0000 DFFFF D0000 CFFFF B0000 AFFFF A0000 9FFFF 80000 7FFFF 70000 6FFFF 60000 5FFFF 50000 4FFFF 40000 3FFFF 30000 2FFFF PRINCIPLES OF OPERATION 20000 1FFFF The LH28F008SA includes on-chip write automation to manage write and erase functions. The Write State Machine allows for 100% TTL-level control inputs; fixed power supplies during block erasure and byte write; and minimal processor overhead with SRAM like interface timings. 10000 0FFFF After initial device powerup, or after return from deep powerdown mode (see Bus Operations), the LH28F008SA functions as a read-only memory. Manipulation of external memory-control pins allow array read, standby and output disable operations. Both Status Register and intelligent identifiers can also be accessed through the Command User Interface when VPP = VPPL. This same subset of operations is also available when high voltage is applied to the VPP pin. In addition, high voltage on VPP enables successful block erasure and byte writing of the device. All functions associated with altering memory contents - byte write, block erase, status and intelligent identifier - are accessed via the Command User Interface and verified through the Status Register. 00000 64KB BLOCK 64KB BLOCK 64KB BLOCK 64KB BLOCK 64KB BLOCK 64KB BLOCK 64KB BLOCK 64KB BLOCK 64KB BLOCK 64KB BLOCK 64KB BLOCK 64KB BLOCK 64KB BLOCK 64KB BLOCK 64KB BLOCK 64KB BLOCK 28F008SA-4 Figure 4. Memory Map Commands are written using standard microprocessor write timings. Command User Interface contents serve as input to the WSM, which controls the block erase and byte write circuitry. Write cycles also internally latch addresses and data needed for byte write or block erase operations. With the appropriate command written to the register, standard microprocessor read timings output array data, access the intelligent identifier codes, or output byte write and block erase status for verification. 5 LH28F008SA 8M (1M × 8) Flash Memory 12 V SA0 - SA16 LA17 - LA20 SA1 - SA16 LA17 - LA20 µPLD WE FLSHDCS RD OE PRDY CS1 VGACS CS2 CTRL SD0 - SD15 CS3 XCVR FD0 - FD7 82360SL CONTROLLER VPP OE RY/BY WR WE DQ0 - DQ7 80386SL PM/IO VPP LH28F008SA CS TO OTHER LH28F008SA's LH28F008SA CE PSTART PCMD GPIO RESET CE CSH1 SBHE PW/R A0 - A19 PWD SBHE CSL1 DQ0 - DQ7 LATCH A0 - A19 RY/BY SA0 LA21 - LA22 VPP SWITCH INT FD8 - FD15 RY/BY RESET PWRGOOD RD WR RY/BY1 RY/BY2 EPLD(s) RY/BY FROM OTHER LH28F008SA's PWD PWD TO OTHER LH28F008SA PAIRS 28F008SA-3 Figure 3. LH28F008SA Array Interface to 386SL Microprocessor Superset through PI Bus (Including RY »/BY » Masking and Selective Powerdown), for DRAM Backup during System SUSPEND, Resident O/S and Applications and Motherboard Solid-State Disk. 6 8M (1M × 8) Flash Memory LH28F008SA Data Protection Interface software to initiate and poll progress of internal byte write and block erase can be stored in any of the LH28F008SA blocks. This code is copied to, and executed from, system RAM during actual flash memory update. After successful completion of byte write and/or block erase, code/data reads from the LH28F008SA are again possible via the Read Array command. Erase suspend/resume capability allows system software to suspend block erase to read data and execute code from any other block. Depending on the application, the system designer may choose to make the VPP power switchable (available only when memory byte writes/block erases are required) or hardwired to VPPH. When VPP = VPPL, memory contents cannot be altered. The LH28F008SA Command User interface architecture provides protection from unwanted byte write or block erase operations even when high voltage is applied to VPP. Additionally, all functions are disabled whenever VCC is below the write lockout voltage VLKO, or when PWD is at VIL. The LH28F008SA accomodates either design practice and encourages optimization of the processormemory interface. Command User Interface and Write Automation An on-chip state machine controls block erase and byte write, freeing the system processor for other tasks. After receiving the Erase Setup and Erase Confirm commands, the state machine controls block pre-conditioning and erase, returning progress via the Status Register and RY »/BY » output. Byte write is similarly controlled, after destination address and expected data are supplied. The program and erase algorithms of past standard Flash memories are now regulated by the state machine, including pulse repetition where required and internal verification and margining of data. The two-step byte write/block erase Command User Interface write sequence provides additional software write protection. BUS OPERATION Flash memory reads, erases and writes in-system via the local CPU. All bus cycles to or from the flash memory conform to standard microprocessor bus cycles. Read The LH28F008SA has three read modes. The memory can be read from any of its blocks, and information can be read from the intelligent identifier or Status Register. VPP can be at either VPPL or VPPH. Bus Operations PWD CE » OE » WE A0 VPP DQ0 - DQ7 RY »/BY » NOTE Read VIH VIL VIL VIH X X DOUT X 1, 2, 3 Output Disable VIH VIL VIH VIH X X High-Z X 3 Standby VIH VIH X X X X High-Z X 3 Deep Power Down VIL X X X X X High-Z VOH Intelligent Identifier (Mfr) VIH VIL VIL VIH VIL X 89H VOH Intelligent Identifier (Device) VIH VIL VIL VIH VIH X A2H VOH Write VIH VIL VIH VIL X X DIN X MODE 3, 4, 5 NOTES: 1. Refer to DC Characteristics. When VPP = VPPL, memory contents can be read but not written or erased. 2. X can be VIL or VIH for control pins and addresses, and VPPL or VPPH for VPP. See DC Characteristics for VPPL and VPPH voltages. 3. RY »/BY » is VOL when the Write State Machine is executing internal block erase or byte write algorithms. It is V OH when the WSM is not busy, in Erase Suspend mode or deep powerdown mode. 4. Command writes involving block erase or byte write are only successfully executed when VPP = VPPH. 5. Refer to the Command Definitions Table for valid DIN during a write operation. 7 LH28F008SA 8M (1M × 8) Flash Memory The first task is to write the appropriate read mode command to the Command User Interface (array, intelligent identifier, or Status Register). The LH28F008SA automatically resets to Read Array mode upon initial device powerup or after exit from deep powerdown. The LH28F008SA has four control pins, two of which must be logically active to obtain data at the outputs. Chip Enable (CE ») is the device selection control, and when active enables the selected memory device. Output Enable (OE ») is the data input/output (DQ0 - DQ7) direction control, and when active drives data from the selected memory onto the I/O bus. PWD and WE » must also be at VIH. Figure 8 illustrates read bus cycle waveforms. Output Disable With OE » at a logic-high level (VIH), the device outputs are disabled. Output pins (DQ0 - DQ7) are placed in a high-impedance state. Standby CE » at a logic-high level (VIH) places the LH28F008SA in standby mode. Standby operation disables much of the LH28F008SA’s circuitry and substantially reduces device power consumption. The outputs (DQ0 - DQ7) are placed in a high-impedance state independent of the status of OE .» If the LH28F008SA is deselected during block erase or byte write, the device will continue functioning and consuming normal active power until the operation completes. Deep Power-Down The LH28F008SA offers a deep power-down feature, entered when PWD is at VIL. Current draw through VCC is 0.20 µA typical in deep powerdown mode, with current draw through VPP typically 0.1 µA. During read modes, PWD-low deselects the memory, places output drivers in a high-impedence state and turns off all internal circuits. The LH28F008SA requires time tPHQV (see AC Characteristics-Read-Only Operations) after return from powerdown until initial memory access outputs are valid. After this wakeup interval, normal operation is restored. The Command User interface is reset to Read Array, and the upper 5 bits of the Status Register are cleared to value 100,000, upon return to normal operation. During block erase or byte write modes, PWD low will abort either operation. Memory contents of the block being altered are no longer valid as the data will be partially written or erased. Time tPHWL after PWD goes to logic-high (VIH) is required before another command can be written. Command Definitions BUS CYCLES REQ'D OPER. ADDRESS DATA Read Array/Reset 1 Write X FFH Intelligent Identifier 3 Write X 90H Read IA IID 2, 3, 4 Read Status Register 2 Write X 70H Read X SRD 3 Clear Status Register 1 Write X 50H Erase Setup/Erase Confirm 2 Write BA 20H Write BA D0H 2 Erase Suspend/Erase Resume 2 Write X B0H Write X D0H Byte Write Setup/Write 2 Write WA 40H Write WD WD 2, 3, 5 Alternate Byte Write Setup/Write 2 Write WA 10H Write WD WD 2, 3, 5 COMMAND FIRST BUS CYCLE SECOND BUS CYCLE NOTE OPER. ADDRESS DATA 1 NOTES: 1. Bus operations are defined in Bus Operations Table. 2. IA = Identifier Address: D0H for manufacturer code, 01H for device code. BA = Address within the block being erased. WA = Address of memory location to be written. 3. SRD = Data read from Status Register. See Status Register Definitions Table for a description of the Status Register bits. WD = Data to be written at location WA. Data is latched on the rising edge of WE ». IID = Data read from intelligent identifiers. 4. Following the intelligent identifier command, two read operations access manufacture and device codes. 5. Either 40H or 10H are recognized by the WSM as the Byte Write Setup command. 6. Commands other than those shown above are reserved by Intel for future device implementations and should not be used. 8 8M (1M × 8) Flash Memory LH28F008SA Intelligent Identifier Operation The intelligent identifier operation outputs the manufacturer code 89H; and the device code, A2H for the LH28F008SA. The system CPU can then automatically match the device with its proper block erase and byte write algorithms. The manufacturer and device-codes are read via the Command User Interface. Following a write of 90H to the Command User Interface, a read from address location 00000H outputs the manufacturer code (89H). A read from address 00001H outputs the device code (A2H). It is not necessary to have high voltage applied to VPP to read the intelligent identifiers from the Command User Interface. data information needed to execute the command. Erase Setup and Erase Confirm commands require both appropriate command data and an address within the block to be erased. The Byte Write Setup command requires both appropriate command data and the address of the location to be written, while the Byte Write command consists of the data to be written and the address of the location to be written. The Command User Interface is written by bringing WE » to a logic-low level (VIL) while CE » is low. Addresses and data are latched on the rising edge of WE ». Standard microprocessor write timings are used. Refer to AC Write Characteristics and the AC Waveforms for Write Operations, Figure 9, for specific timing parameters. Write Writes to the Command User Interface enable reading of device data and intelligent identifiers. They also control inspection and clearing of the Status Register. Additionally, when VPP = VPPH, the Command User Interface controls block erasure and byte write. The contents of the interface register serve as input to the internal state machine. The Command User Interface itself does not occupy an addressable memory location. The interface register is a latch used to store the command and address and COMMAND DEFINITIONS When VPPL is applied to the VPP pin, read operations from the Status Register, intelligent identifiers, or array blocks are enabled. Placing VPPH on VPP enables successful byte write and block erase operations as well. Device operations are selected by writing specific commands into the Command User Interface. Command Definitions Table defines the LH28F008SA commands. Status Register Definitions WSMS ESS ES BWS VPPS R R R 7 6 5 4 3 2 1 0 SR.7 = WRITE STATE MACHINE STATUS (WSMS) 1 = Ready 0 = Busy SR.6 = ERASE-SUSPEND STATUS (ESS) 1 = Erase Suspended 0 = Erase in Progress/Completed SR.5 = ERASE STATUS (ES) 1 = Error in Block Erasure 0 = Successful Block Erase SR.4 = BYTE WRITE STATUS (BWS) 1 = Error in Byte Write 0 = Successful Byte Write SR.3 = VPP STATUS (VPPS) 1 = VPP Low Detect, Operation Abort 0 = VPP OK NOTES: 1. RY »/BY » or the Write State Machine Status bit must first be checked to determine byte write or block erase operation, before the Byte Write or Erase Status bit are checked to success. 2. If the Byte Write AND Erase Status bits are set to '1's during a block erase attempt, an improper command sequence was entered. Attempt the operation again. 3. If VPP low status is detected, the Status Register must be cleared before another byte write or block erase operation is attempted. The VPP Status bit, unlike an A/D converter, does not provide continuous indication of VPP level. The WSM interrogates the VPP level only after the byte write or block erase command sequences have been entered and informs the system if VPP has not been switched on. The VPP Status bit is not gauranteed to report accurate feedback between VPPL and VPPH. 4. SR.2 - SR.0 = Reserved for future enhancements. These bits are reserved for future use and should be masked out when polling the Status Register. 9 LH28F008SA Read Array Command Upon initial device powerup and after exit from deep powerdown mode, the LH28F008SA defaults to Read Array mode. This operation is also initiated by writing FFH into the Command User Interface. Microprocessor read cycles retrieve array data. The device remains enabled for reads until the Command User Interface contents are altered. Once the internal Write State Machine has started a block erase or byte write operation, the device will not recognize the Read Array command, until the WSM has completed its operation. The Read Array command is functional when VPP = VPPL or VPPH. Intelligent Identifier Command The LH28F008SA contains an intelligent identifier operation, initiated by writing 90H into the Command User Interface. Following the command write, a read cycle from address 00000H retrieves the manufacturer code of 89H. A read cycle from address 00001H returns the device code of A2H. To terminate the operation, it is necessary to write another valid command into the register. Like the Read Array command, the intelligent identifier command is functional when VPP = VPPL or VPPH. Read Status Register Command The LH28F008SA contains a Status Register which may be read to determine when a byte write or block erase operation is complete, and whether that operation completed successfully. The Status Register may be read at any time by writing the Read Status Register command (70H) to the Command User Interface. After writing this command, all subsequent read operations output data from the Status Register, until another valid command is written to the Command User Interface. The contents of the Status Register are latched on the falling edge of OE » or CE », whichever occurs last in the read cycle. OE » or CE » must to toggled to VIH before further reads to update the Status Register latch. The Read Status Register command functions when VPP = VPPL or VPPH. Clear Status Register Command The Erase Status and Byte Write Status bits are set to '1's by the Write State Machine and can only be reset by the Clear Status Register Command. These bits indicate various failure conditions (see Status Register Definitions). By allowing system software to control the resetting of these bits, several operations may be performed (such as cumulatively writing several bytes or erasing multiple blocks in sequence). The Status Register may then be polled to determine if an error occurred during that sequence. This adds flexibility to the way the device may be used. 10 8M (1M × 8) Flash Memory Additionally, the VPP Status bit (SR.3) MUST be reset by system software before further byte writes or block erases are attempted. To clear the Status Register, the Clear Status Register command (50H) is written to the Command User Interface. The Clear Status Register command is functional when VPP = VPPL or VPPH. Erase Setup/Erase Confirm Commands Erase is executed one block at a time, initiated by a two-cycle command sequence. An Erase Setup command (20H) is first written to the Command User Interface, followed by the Erase Confirm command (D0H). These commands require both appropriate sequencing and an address within the block to be erased to FFH. Block preconditioning, erase and verify are all handled internally by the Write State Machine, invisible to the system. After the two-command erase sequence is written to it, the LH28F008SA automatically outputs Status Register data when read (see Block Erase Flowchart). The CPU can detect the completion of the erase event by analyzing the output of the RY »/BY » pin, or the WSM Status bit of the Status Register. When erase is completed, the Erase Status bit should be checked. If erase error is detected, the Status Register should be cleared. The Command User Interface remains in Read Status Register mode until further commands are issued to it. This two-step sequence of set-up followed by execution insures that memory contents are not accidentially erased. Also, reliable block erasure can only occur when VPP = VPPH. In the absence of this high voltage, memory contents are protected against erasure. If block erase is attempted while VPP = VPPL, the VPP Status bit will be set to '1'. Erase attempts while VPPL < VPP < VPPH produce spurious results and should not be attempted. Erase Suspend/Erase Resume Commands The Erase Suspend command allows block erase interruption in order to read data from another block of memory. Once the erase process starts, writing the Erase Suspend command (B0H) to the Command User Interface requests that the WSM suspend the erase sequence at a predetermined point in the erase algorithm. The LH28F008SA continues to output Status Register data when read, after the Erase Suspend command is written to it. Polling the WSM Status and Erase Suspend Status bits will determined when the erase operation has been suspended (both will be set to '1'). RY »/BY » will also transition to VOH. 8M (1M × 8) Flash Memory At this point, a Read Array command can be written to the Command User Interface to read data from blocks other than that which is suspended. The only other valid commands at this time are Read Status Register (70H) and Erase Resume (D0H), at which time the WSM will continue with the erase process. The Erase Suspend Status and WSM Status bits of the Status Register will be automatically cleared and RY »/BY » will return to VOL. After the Erase Resume command is written to it, the LH28F008SA automatically outputs Status Register data when read (see Erase Suspend/Resume Flowchart). V PP must remain at V PPH while the LH28F008SA is in Erase Suspend. Byte Write Setup/Write Commands Byte write is executed by a two-command sequence. The Byte Write Setup command (40H) is written to the Command User Interface, followed by a second write specifying the address and data (latched on the rising edge of WE ») to be written. The WSM then takes over, controlling the byte write and write verify algorithms internally. After the two-command byte write sequence is written to it, the LH28F008SA automatically outputs Status Register data when read (see Byte Write Flowchart). The CPU can detect the completion of the byte write event by analyzing the output of the RY /» BY » pin, or the WSM Status bit of the Status Register. Only the Read Status Register command is valid while byte write is active. When byte write is complete, the Byte Write Status bit should be checked. If byte write error is detected, the Status Register should be cleared. The internal WSM verify only detects errors for '1's that do not successfully write to '0's. The Command User Interface remains in Read Status Register mode until further commands are issued to it. If byte write is attempted while VPP = VPPL, the VPP Status bit will be set to '1'. Byte write attempts while VPPL < VPP < VPPH produce spurious results and should not be attempted. EXTENDED BLOCK ERASE/BYTE WRITE CYCLING The LH28F008SA is designed for 100,000 byte write/ block erase cycles on each of the sixteen 64K blocks. Low electric fields, advanced oxides and minimal oxide area per cell subjected to the tunneling electric field combine to greatly reduce oxide stress and the probability of failure. A 20M solid-state drive using an array of LH28F008SAs has a MTBF (Mean Time Between Failure) of 33.3 million hours(1), over 600 times more reliable than equivalent rotating disk technology. LH28F008SA AUTOMATED BYTE WRITE The LH28F008SA integrates the Quick-Pulse programming algorithm using the Command User Interface, Status Register and Write State Machine (WSM). On-chip integration dramatically simplifies system software and provides processor interface timings to the Command User Interface and Status Register. WSM operation, internal verifyand V PP high voltage presence are monitored and reported via the RY »/BY » output and appropriate Status Register bits. Figure 5 shows a system software flowchart for device byte write. The entire sequence is performed with VPP at VPPH. Byte write abort occurs when PWD transitions to VIL, or VPP drops to VPPL. Although the WSM is halted, byte data is partially written at the location where byte write aborted. Block erasure, or a repeat of byte write, is required to initialize this data to a known value. AUTOMATED BLOCK ERASE As above, the Quick-Erase algorithm is now implemented internally, including all preconditioning of block data. WSM operation, erase success and VPP high voltage presence are monitored and reported through RY »/BY » and the Status Register. Additionally, if a command other than Erase Confirm is written to the device following Erase Setup, both the Erase Status and Byte Write Status bits will be set to '1's. When issuing the Erase Setup and Erase Confirm commands, they should be written to an address within the address range of the block to be erased. Figure 6 shows a system software flowchart for block erase. Erase typically takes 1.6 seconds per block. The Erase Suspend/Erase Resume command sequence allows suspension of this erase operation to read data from a block other than that in which erase is being performed. A system software flowchart is shown in Figure 7. The entire sequence is performed with VPP at VPPH. Abort occurs when PWD transitions to VIL or VPP fails to VPPL, while erase is in progress. Block data is partially erased by this operation, and a repeat of erase is required to obtain a fully erased block. 11 LH28F008SA DESIGN CONSIDERATIONS Three-Line Output Control The LH28F008SA will often be used in large memory arrays. Intel provides three control inputs to accommodate multiple memory connections. Three-line control provides for: • Lowest possible memory power dissipation • Complete assurance that data bus contention will not occur To efficiently use these control input, an address decoder should enable CE ,» while OE » should be connected to all memory devices and the system’s READ control line. This assures that only selected memory devices have active outputs while deselected memory devices are in Standby Mode. Finally, PWD should either be tied to the system RESET, or connected to VCC if unused. NOTE: 1. Assumptions: 10K file written every 10 minutes. (20M array 10K file) = 2,000 file writes before erase required. (2000 files writes/erase) × (100,000 cycles per LH28F008SA block) = 200 million file writes. (200 × 106 file writes) × 10 minutes/write) × 1 hr/60 minutes) = 33.3 × 102 MTBF. RY /» BY » and Byte Write/Block Erase Polling RY »/BY » is a full CMOS output that provides a hardware method of detecting byte write and block erase completion. It transitions low time tWHRL after a write or erase command sequence is written to the LH28F008SA, and returns to VOH when the WSM has finished executing the internal algorithm. RY /» BY » can be connected to the interrupt input of the system CPU or controller. It is active at all times, not instated if the LH28F008SA CE» or OE » inputs are brought to VIH. RY »/BY » is also VOH when the device is in Erase Suspend or deep powerdown modes. Power Supply Decoupling Flash memory power switching characteristics require careful device decoupling. System designers are interested in 3 supply current issues: standby current levels (ISB), active current levels (ICC) and transient peaks produced by falling and rising edges of CE .» Transient current magnitudes depend on the device outputs’ capacitive and inductive loading. Two-line control and proper decoupling capacitor selection will supress transient voltage peaks. Each device should have a 0.1 µF ceramic capacitor connected between each VCC and GND, and between its VPP and GND. These high frequency, low inherent-inductance capacitors should be placed as close as possible to package leads. Addition- 12 8M (1M × 8) Flash Memory ally, for every 8 devices, a 4.7 µF electrolytic capacitor should be placed at the array’s power supply connection between V CC and GND. The bulk capacitor will overcome voltage slumps caused by PC board trace inductances. VPP Trace on Printed Circuit Boards Writing flash memories, while they reside in the target system, requires that the printed circuit board designer pay attention to the VPP power supply trace. The VPP pin supplies the memory cell current for writing and erasing. Use similar trace widths and layout considerations given to the VCC power bus. Adequate VPP Supply traces and decoupling will decrease VPP voltage spikes and overshoots. VCC, VPP, PWD Transitions and the Command/Status Registers Byte write and block erase completion are not guaranteed if VPP drops below VPPH. If the VPP Status bit of the Status Register (SR.3) is set to '1', a Clear Status Register command MUST be issued before further byte write/block erase attempts are allowed by the WSM. Otherwise, the Byte Write (SR.4) or Erase (SR.5) Status bits of the Status Register will be set to '1's if error is detected. PWD transitions to VIL during byte write and block erase also abort the operations. Data is partially altered in either case, and the command sequence must be repeated after normal operation is restored. Device poweroff, or PWD transitions to VIL, clear the Status Register to initial value 10,000 for the upper 5 bits. The Command User Interface latches commands as issued by system software and is not altered by VPP or CE » transitions or WSM actions. Its state upon power up, after exit from deep powerdown or after VCC transitions below VLKO, is Read Array Mode. After byte write or block erase is complete, even after VPP transitions down to VPPL, the Command User Interface must be reset to Read Array mode via the Read Array command if access to the memory array is desired. Power Up/Down Protection The LH28F008SA is designed to offer protection against accidental block erasure or byte writing during power transitions. Upon power-up, the LH28F008SA is indifferent as to which power supply, VPP or VCC, powers up first. Power supply sequencing is not required. Internal circuitry in the LH28F008SA ensures that the Command User Interface is reset to the Read Array mode on power up. 8M (1M × 8) Flash Memory LH28F008SA START BUS OPERATION WRITE 40H (10H), BYTE ADDRESS WRITE BYTE ADDRESS/DATA COMMAND COMMENTS Write Byte Write Setup Data = 40H (10H) Addr = Byte to be written Write Byte Write Data to be written Addr = Byte to be written Check RY/BY VOH = Ready, VOL = Busy Standby/Read or WSM READY? Read Status Register Check SR.7 1 = Ready, 0 = Busy Toggle OE or CE to update Status Register NO YES Repeat for subsequent bytes. FULL STATUS CHECK IF DESIRED Full status check can be done after each byte or after a sequence of bytes. BYTE WRITE COMPLETED Write FFH after the last byte write operation to reset the device to Read Array Mode. FULL STATUS CHECK PROCEDURE STATUS REGISTER DATA READ (see above) SR.3 = 0 ? NO BUS OPERATION VPP RANGE ERROR YES SR.4 = 0 ? NO YES BYTE WRITE SUCCESSFUL BYTE WRITE ERROR COMMAND COMMENTS Optional Read CPU may already have read Status Register data in WSM Ready polling above Standby Check SR.3 1 = VPP Low Detect Standby Check SR.4 1 = Byte Write Error SR.3 must be cleared, if set during a byte write attempt, before further attempts are allowed by the Write State Machine. SR.4 is only cleared by the Clear Status Register Command, in cases where multiple bytes are written before full status is checked. If error is detected, clear the Status Register before attempting retry or other error recovery. 28F008SA-5 Figure 5. Automated Byte Write Flowchart 13 LH28F008SA 8M (1M × 8) Flash Memory BUS OPERATION START COMMAND Write Erase Setup Data = 20H Addr = Within block to be erased Write Erase Data = D0H Addr = Within block to be erased WRITE 20H BLOCK ADDRESS WRITE D0H BLOCK ADDRESS Standby/Read NO WSM READY? NO Check RY/BY VOH = Ready, VOL = Busy ERASE SUSPEND LOOP SUSPEND ERASE? or Read Status Register Check SR.7 1 = Ready, 0 = Busy Toggle OE or CE to update Status Register YES YES FULL STATUS CHECK IF DESIRED COMMENTS Repeat for subsequent bytes. Full status check can be done after each block or after a sequence of blocks. BLOCK ERASE COMPLETED Write FFH after the last block erase operation to reset the device to Read Array Mode. FULL STATUS CHECK PROCEDURE BUS OPERATION STATUS REGISTER DATA READ (see above) SR.3 = 0 ? NO COMMAND Optional Read CPU may already have read Status Register data in WSM Ready polling above Standby Check SR.3 1 = VPP Low Detect Standby Check SR.4, 5 Both 1 = Command Sequence Error Standby Check SR.5 1 = Block Erase Error VPP RANGE ERROR YES SR.4, 5 = 1 ? YES COMMAND SEQUENCE ERROR SR.3 must be cleared, if set during a block erase attempt, before further attempts are allowed by the Write State Machine. NO SR.5 = 0 ? COMMENTS NO YES BLOCK ERASE SUCCESSFUL BLOCK ERASE ERROR SR.5 is only cleared by the Clear Status Register Command, in cases where multiple blocks are erased before full status is checked. If error is detected, clear the Status Register before attempting retry or other error recovery. 28F008SA-6 Figure 6. Automated Block Erase Flowchart 14 8M (1M × 8) Flash Memory LH28F008SA START BUS OPERATION WRITE B0H COMMAND Write Erase Suspend Data = B0H Write Read Status Register Data = 70H WRITE 70H Check RY/BY VOH = Ready, VOL = Busy or Read Status Register Standby/Read READ STATUS REGISTER SR.7 = 1 ? Check SR.7 1 = Ready, 0 = Busy Toggle OE or CE to Update Status Register NO Standby Check SR.6 1 = Suspended YES Write SR.6 = 1 ? YES COMMENTS Read Array Data = FFH NO Read ERASE HAS COMPLETED Write Read array data from block other than that being erased. Erase Resume Data = D0H WRITE FFH DONE READING ? NO YES WRITE D0H CONTINUE ERASE 28F008SA-7 Figure 7. Erase Suspend/Erase Resume Flowchart A system designer must guard against spurious writes for VCC voltages above VLKO when VPP is active. Since both WE » and CE » must be low for a command write, driving either to VIH will inhibit writes. The Command User Interface architecture provides an added level of protection since alteration of memory contents only occurs after successful completion of the two-setup command sequences. Finally, the device is disabled until PWD is brought to VIH, regardless of the state of its control inputs. This provides an additional level of memory protection. Power Dissipation When designing portable systems, designers must consider battery power consumption not only during device operation, but also for data retention during system idle time. Flash nonvolatility increases usable battery life, because the LH28F008SA does not consume any power to retain code or data when the system is off. In addition, the LH28F008SA’s deep powerdown mode ensures extremely low power dissipation even when system power is applied. For example, portable PCs and other power sensitive applications, using an array of LH28F008SAs for solid-state storage, can lower PWD to VIL in standby or sleep modes, producing negligible power consumption. If access to the LH28F008SA is again needed, the part can again be read, following the tPHQV and tPHWL wakeup cycles required after PWD is first raised back to VIH. See AC Characteristics - ReadOnly and Write Operations and Figures 8 and 9 for more information. 15 LH28F008SA 8M (1M × 8) Flash Memory *WARNING: Stressing the device beyond ABSOLUTE MAXIMUM RATINGS* Operating Temperature During Read ......................................... 0°C to +70°C1 During Block Erase/Byte Write ............... 0°C to +70°C Temperature Under Bias ..................... -10°C to +80°C the “Absolute Maximum Ratings” may cause permanent damage. These are stress ratings only. Operation beyond the “Operating Conditions” is not recommended and extended exposure beyond the “Operating Conditions” may affect device reliability. Storage Temperature ......................... -65°C to +125°C Voltage on Any Pin (except VCC and VPP) with Respect to GND ..................... -2.0 V to +7.0 V2 VPP Program Voltage with Respect to GND during Block Erase/Byte Write .............-2.0 V to +14.0 V2, 3 VCC Supply Voltage with Respect to GND ........................................... -2.0 V to +7.0 V2 Output Short Circuit Current .......................... 100 mA4 OPERATING CONDITIONS SYMBOL TA PARAMETER MIN. MAX. UNITS 0 70.0 °C Operating Temperature NOTE VCC VCC Supply Voltage (10%) 4.50 5.50 V 5 VCC VCC Supply Voltage (5%) 4.75 5.25 V 5 NOTES: 1. Operating temperature is for commercial product defined by this specification. 2. Minimum DC voltage is -0.5 V on input/output pins. During transitions, this level may undershoot to -2.0 V for periods < 20 ns. Maximum DC voltage on input/output pins is VCC + 0.5 V which, during transitions, may overshoot to VCC + 2.0 V for periods < 20 ns. 3. Maximum DC voltage on VPP may overshoot to +14.0 V for periods < 20 ns. 4. Output shorted for no more than one second. No more than one output shorted at a time. 5. 5% VCC specification reference the LH28F008SA-85 in its High Speed configuration, 10% V CC specifications reference the LH28F008SA-85 in its Standard configuration, and the LH28F008SA-12. DC CHARACTERISTICS SYMBOL PARAMETER TYP. MAX. UNITS TEST CONDITIONS NOTE ILI Input Load Current ±1.0 µA VCC = VCC MAX., VIN = VCC or GND 1 ILO Output Leakage Current ±10.0 µA VCC = VCC MAX., VOUT = VCC or GND 1 1.0 2.0 mA VCC = VCC MAX., CE » = PWD = VIH 30 100.0 µA VCC = VCC MAX., CE » = PWD = Vcc ±0.2 V 0.20 1.2 µA PWD = GND ±0.2 IOUT (RY »/BY ») = 0 mA 20 35.0 mA VCC = VCC MAX., CE » = GND f = 8 MHz, IOUT = 0 mA CMOS Inputs mA VCC = VCC MAX., CE » = VIL f = 8 MHz, IOUT = 0 mA TTL Inputs ICCS VCC Standby Current ICCD VCC Deep Power Down Current ICCR VCC Read Current 1, 3 1 1 25 16 MIN. 50.0 8M (1M × 8) Flash Memory LH28F008SA DC Characteristics (Continued) SYMBOL PARAMETER TYP. MIN. MAX. UNITS TEST CONDITIONS NOTE ICCW VCC Byte Write Current 10 30 mA Byte Write in Progress 1 ICCE VCC Block Erase Current 10 30 mA Block Erase in Progress 1 ICCES VCC Erase Suspend Current 5 10 mA Block Erase Suspended CE » = VIH 1, 2 ±1 ±10 µA VPP ≤ VCC 90 200 µA VPP ≤ VCC 0.10 5.0 µA PWD = GND ±0.2 V 1 IPPS VPP Standby Current 1 IPPD VPP Deep Power Down Current IPPW VPP Byte Write Current 10 30 mA VPP = VPPH Byte Write in Progress 1 IPPE VPP Block Erase Current 10 30 mA VPP = VPPH, Block Erase in Progress 1 IPPES VPP Erase Suspend Current 90 200 µA VPP = VPPH, Block Erase Suspended 1 VIL Input Low Voltage -0.5 0.8 V VIH Input High Voltage 2.0 VCC + 0.5 V VOL Output Low Voltage 0.45 V VCC = VCC MIN. IOL = 5.8 mA 3 VOH Output High Voltage 2.4 V VCC = VCC MIN. IOL = 2.5 mA 3 VPPL VPP during Normal Operations 0.0 6.5 V VPPH VPP during Write/Erase Operations 11.4 12.6 V VLKO VCC Erase/Write Lock Voltage 12 2.0 4 V Capacitance5 TA = 25°C, f = 1MHz SYMBOL CIN COUT PARAMETER TYP. MAX. UNITS TEST CONDITIONS Input Capacitance 6 8 pF VIN = 0 V Output Capacitance 8 12 pF VIN = 0 V NOTES: 1. All currents are in RMS unless otherwise noted. Typical values at VCC = 5.0 V, VPP = 12.0 V, T = 25°C. These currents are valid for all product versions (package and speeds). 2. ICCES is specified with the device deseleted. If the LH28F008SA is read while in Erase Suspend Mode, current draw is the sum of ICCES and ICCR. 3. Includes RY »/BY ». 4. Block Erases/Byte Writes are inhibited when VPP = VPPL and not guaranteed in the range between V PPH and VPPL. 5. Sampled, not 100% tested. 17 LH28F008SA 8M (1M × 8) Flash Memory AC INPUT/OUTPUT REFERENCE WAVEFORM1 2.4 INPUT 0.45 2.0 0.8 HIGH SPEED AC INPUT/OUTPUT REFERENCE WAVEFORM2 2.0 TEST POINTS 0.8 3.0 OUTPUT INPUT 1.5 1.5 OUTPUT TEST POINTS 0.0 NOTE: AC test inputs are driven at VOH (2.4 VTTL) for a Logic '1' and VOL (0.45 VTTL) for a Logic '0.' Input timing begins at VIH (2.0 VTTL) and VIL (0.8 VTTL). Output timing ends at VIH and VIL. Input rise and fall times (10% to 90%) < 10 ns. NOTE: AC test inputs are driven at 3.0 V for a Logic '1' and 0.0 V for a Logic '0'. Input timing begins, and output timing ends at 1.5 V. Input rise and fall times (10% to 90%) < 10 ns. 28F008SA-9 28F008SA-8 AC TESTING LOAD CIRCUIT1 HIGH SPEED AC TESTING LOAD CIRCUIT2 1.3 V 1.3 V 1N914 1N914 RL DEVICE UNDER TEST RL DEVICE UNDER TEST OUT CL NOTE: CL = 100 pF CL Includes Jig Capacitance RL = 3.3 kΩ CL 28F008SA-10 NOTES: 1. Testing characteristics for LH28F008SA-85 in Standard configuration, and LH28F008SA-12. 2. Testing characteristics for LH28F008SA-85 in High Speed configuration 18 OUT NOTE: CL = 30 pF CL Includes Jig Capacitance RL = 3.3 kΩ 28F008SA-11 8M (1M × 8) Flash Memory LH28F008SA AC CHARACTERISTICS - Read Only Operations1 SYMBOL PARAMETER LH28F008SA-854 LH28F008SA-855 LH28F008SA-125 VCC ± 5% VCC ± 10% VCC ± 10% MIN. MAX. 85 MIN. MAX. 90 MIN. UNIT NOTE MAX. tAVAV tAC Read Cycle Time tAVQV tACC Address to Output Delay 85 90 120 ns tELQV tCE CE » to Output Delay 85 90 120 ns tPHQV tPWH PWD High to Output Delay 400 400 400 ns tGLQV tOE OE » to Output Delay 40 45 50 ns 2 tELQX tLZ CE » to Output Low Z ns 3 tEHQZ tHZ CE » High to Output High Z ns 3 tGLQX tOLZ OE » to Output Low Z ns 3 tGHQZ tDF OE » High to Output High Z ns 3 tOH Output Hold from Addresses, CE » or OE » change, whichever is first ns 3 0 0 55 0 0 55 0 30 0 ns 0 55 30 0 120 30 0 2 NOTES: 1. See AC Input/Output Reference Waveform for timing measurements. 2. OE » may be delayed up to tCE - tOE after the falling edge of CE » without impact on tCE. 3. Sampled, not 100% tested. 4. See High Speed AC Input/Output Reference Waveforms and High Speed AC Testing Load circuits for testing characteristics. 5. See AC Input/Output Reference Waveforms and AC Testing Load Circuits for testing characteristics. 19 LH28F008SA 8M (1M × 8) Flash Memory VCC POWER-UP ADDRESSES (A) DEVICE AND ADDRESS STANDBY SELECTION VIH VIL OUTPUTS ENABLED DATA VALID ADDRESSES STABLE ... VCC STANDBY POWER-DOWN ... tAVAV CE (E) VIH ... VIL tEHQZ OE (G) VIH VIL ... tGHQZ WE (W) VIH VIL tGLQV tELQV tOH tGLQX tELQX DATA (D/Q) VOH ... ... HIGH-Z VALID OUTPUT VOL HIGH-Z tAVQV VCC 5.0 V GND tPHQV PWD (P) VIH VIL 28F008SA-12 Figure 8. AC Waveform for Read Operations 20 8M (1M × 8) Flash Memory LH28F008SA AC CHARACTERISTICS - Write Operations1 SYMBOL PARAMETER LH28F008SA-857 LH28F008SA-858 LH28F008SA-128 VCC ± 5% VCC ± 10% VCC ± 10% MIN. MAX. MIN. MAX. MIN. UNIT NOTE MAX. tAVAV tWC Write Cycle Time 85 90 120 ns tPHWL tPS PWD High Recovery to WE Going Low 1 1 1 µs tELWL tCS CE » Setup to WE Going Low 10 10 10 ns tWLWH tWP WE Pulse Width 40 40 40 ns tVPWH tVPS VPP Setup to WE Going High 100 100 100 ns 2 tAVWH tAS Address Setup to WE Going High 40 40 40 ns 3 tDVWH tOS Data Setup to WE Going High 40 40 40 ns tWHDX tDH Data Hold from WE High 5 5 5 ns tWHAX tAH Address Hold from WE High 5 5 5 ns tWHEH tOH OE » Hold from WE High 10 10 10 ns 30 30 30 ns tWHWL tWHP WE Pulse Width High tWHRL WE High to RY »/BY » Going Low tWHQV1 Duration of Byte Write Operation tWHQV2 Duration of Block Erase Operation tWHGL tQVVL tVPH 100 100 100 2 4 ns 6 6 6 µs 0.3 0.3 0.3 s Write Recovery before Read 0 0 0 µs VPP Hold from Valid SRD, RY »/BY » High 0 0 0 ns NOTES: 1. Read timing characteristics during erase and byte write operations are the same as during read-only operations. Refer to AC Characteristics for Read-Only Operations. 2. Sampled, not 100% tested. 3. Refer to Command Definitions Table for Valid AIN for byte write or block erasure. 4. Refer to Command Definitions Table for valid DIN for byte write or block erasure. 5. The on-chip Write State Machine incorporates all byte write and block erase system functions and overhead of standard Intel flash memory, including byte program and verify (byte write) and block precondition, precondition verify, erase and erase verify (block erase). 6. Byte write and block erase durations are measure to completion (SR.7 = 1. RY /» BY » = VOH). VPP should be held at VPPH until determination of byte write/block erase success (SR.3/4/5 = 0). 7. See High Speed AC Input/Output Reference Waveforms and High Speed AC Testing Load Circuits for testing characteristics. 8. See AC Input/Output Reference Waveforms and AC Testing Load Circuits for testing characteristics. 21 LH28F008SA 8M (1M × 8) Flash Memory BLOCK ERASE AND BYTE WRITE PERFORMANCE LH28F008SA-85 PARAMETER TYP.1 MIN. LH28F008SA-12 MAX. TYP.1 MIN. UNIT NOTE MAX. Block Erase Time 1.6 10 1.6 10 s 2 Block Write Time 0.6 2.1 0.6 2.1 s 2 NOTES: 1. 25°C, 12.0 VPP. 2. Excludes System-Level Overhead. VCC POWER-UP AND STANDBY ADDRESSES (A) WRITE BYTE WRITE OR ERASE SETUP COMMAND WRITE VALID ADDRESS AND DATA (BYTE WRITE) OR ERASE CONFIRM COMMAND AIN AIN VIH VIL tAVAV CE (E) tAVWH AUTOMATED BYTE WRITE OR ERASE DELAY READ STATUS REGISTER DATA WRITE READ ARRAY COMMAND tWHAX VIH VIL tELWL tWHGL tWHEH OE (G) VIH VIL tWHWL WE (W) tWHQV1, 2 VIH VIL tWLWH tDVWH tWHDX DATA (D/Q) VIH VIL HIGH-Z DIN tPHWL RY/BY (R) PWD (P) VALID SRD DIN DIN tWHRL VOH VOL VIH VIL tVPWH tQVVL VPPH VPPL VPP (V) V IH VIL 28F008SA-13 Figure 9. AC Waveform for Write Operations 22 8M (1M × 8) Flash Memory LH28F008SA ALTERNATIVE CE » - CONTROLLED WRITES SYMBOL PARAMETER LH28F008SA-856 LH28F008SA-857 LH28F008SA-127 VCC ± 5% VCC ± 10% VCC ± 10% MIN. MAX. MIN. MAX. MIN. UNIT NOTE MAX. tAVAV tWC Write Cycle Time 85 90 120 ns tPHEL tPS PWD High Recovery to CE » Going Low 1 1 1 µs tWLEL tWS WE Setup to CE » Going Low 0 0 0 ns tELEH tCP CE » Pulse Width 50 50 50 ns tVPEH tVPS VPP Setup to CE » Going High 100 100 100 ns 2 tAVEH tAS Address Setup to CE » Going High 40 40 40 ns 3 tDVEH tDS Data Setup to CE » Going High 40 40 40 ns 4 tEHDX tDH Data Hold from CE » High 5 5 5 ns tEHAX tAH Address Hold from CE » High 5 5 5 ns tEHWH tWH WE Hold from CE » High 0 0 0 ns tEHEL tEPH CE » Pulse Width High 25 25 25 ns tEHRL CE » High to RY »/BY » Going Low tEHOV1 Duration of Byte Write Operation tEHOV2 Duration of Block Erase Operation tEHGL tQVVL tVPH 100 100 100 2 ns 6 6 6 µs 5 0.3 0.3 0.3 s 5 Write Recovery before Read 0 0 0 µs VPP Hold from Valid SRD, RY »/BY » High 0 0 0 ns 2, 5 NOTE: 1. Chip-Enable Controlled Writes: Write operations are driven by the valid combinations of CE » and WE ». In systems where CE » defines the write pulsewidth (within a longer WE » timing waveform), all setup, hold and inactive WE » times should be measured relative to the CE » waveform. 2. Sampled, not 100% tested. 3. Refer to Command Definitions Table for valid AIN for byte write or block erasure. 4. Refer to Command Definitions Table for valid DIN for byte write or block erasure. 5. Byte write and block erase durations are measured to completion (SR.7 = 1, RY »/BY » = VOH). VPP should be held at VPPH until determination of byte write/block erase success (SR.3/4/5 = 0). 6. See High Speed AC Input/Output Reference Waveforms and High Speed AC Testing Load Circuits for testing characteristics. 7. See AC Input/Output Reference Waveforms and AC Testing Load Circuits for testing characteristics. 23 LH28F008SA 8M (1M × 8) Flash Memory VCC POWER-UP AND STANDBY ADDRESSES (A) WRITE BYTE WRITE OR ERASE SETUP COMMAND WRITE VALID ADDRESS AND DATA (BYTE WRITE) OR ERASE CONFIRM COMMAND AIN AIN VIH VIL tAVAV WE (W) VIH VIL tAVEH AUTOMATED BYTE WRITE OR ERASE DELAY READ STATUS REGISTER DATA WRITE READ ARRAY COMMAND tEHAX tWLEL tEHGL tEHWH OE (G) VIH VIL tEHEL CE (E) tEHQV1, 2 VIH VIL tELEH tDVEH tEHDX DATA (D/Q) VIH HIGH-Z VIL DIN tPHEL RY/BY (R) VOH VOL PWD (P) VIH VIL VALID SRD DIN DIN tEHRL tVPEH tQVVL VPPH VPPL VPP (V) V IH VIL 28F008SA-14 Figure 10. Alternate AC Waveform for Write Operations 24 8M (1M × 8) Flash Memory LH28F008SA 44SOP (SOP044-P-0600) 0.50 [0.020] 0.30 [0.012] 1.27 [0.050] TYP. 44 23 13.40 [0.528] 13.00 [0.512] 1 16.40 [0.646] 15.60 [0.614] 14.40 [0.567] SEE DETAIL 22 0.20 [0.008] 0.10 [0.004] 28.40 [1.118] 28.00 [1.102] 2.9 [0.114] 2.5 [0.098] DETAIL 1.275 [0.050] 0.15 [0.006] 1.275 [0.050] 0.25 [0.010] 0.05 [0.002] 2.9 [0.114] 2.5 [0.098] 3.25 [0.128] 2.45 [0.096] 0.25 [0.010] 0.05 [0.002] 1.275 [0.050] DIMENSIONS IN MM [INCHES] MAXIMUM LIMIT MINIMUM LIMIT 0 - 10° 0.80 [0.031] 44SOP 25 LH28F008SA 8M (1M × 8) Flash Memory 40TSOP (TSOP040-P-1020) 40 1 0.50 [0.020] TYP. 10.20 [0.402] 9.80 [0.386] 0.25 [0.010] 0.15 [0.006] 20 21 1.10 [0.043] 0.90 [0.035] SEE DETAIL 1.19 [0.047] MAX. 0.49 [0.019] 0.39 [0.015] DETAIL 0.125 [0.005] 18.60 [0.732] 18.20 [0.717] 19.30 [0.760] 18.70 [0.736] 20.30 [0.799] 19.70 [0.776] DIMENSIONS IN MM [INCHES] MAXIMUM LIMIT MINIMUM LIMIT 0.49 [0.019] 0.39 [0.015] 0.22 [0.009] 0.02 [0.001] 0 - 10° 0.18 [0.007] 0.08 [0.003] 40TSOP ORDERING INFORMATION LH28F008SA Device Type X Package -## Speed 85 85 12 120 Access Time (ns) T 40-pin, 1.2 mm x 10 mm x 20 mm TSOP (Type I) (TSOP040-P-1020) N 44-pin, 600-mil SOP (SOP044-P-0600) 8M (1M x 8) Flash Memory Example: LH28F008SAT-85 (8M (1M x 8) Flash Memory, 85 ns, 40-pin TSOP) 28F008SA-15 26 8M (1M × 8) Flash Memory LH28F008SA LIFE SUPPORT POLICY SHARP components should not be used in medical devices with life support functions or in safety equipment (or similiar applications where component failure would result in loss of life or physical harm) without the written approval of an officer of the SHARP Corporation. WARRANTY SHARP warrants to Customer that the Products will be free from defects in material and workmanship under normal use and service for a period of one year from the date of invoice. Customer's exclusive remedy for breach of this warranty is that SHARP will either (i) repair or replace, at its option, any Product which fails during the warranty period because of such defect (if Customer promptly reported the failure to SHARP in writing) or, (ii) if SHARP is unable to repair or replace, SHARP will refund the purchase price of the Product upon its return to SHARP. This warranty does not apply to any Product which has been subjected to misuse, abnormal service or handling, or which has been altered or modified in design or construction, or which has been serviced or repaired by anyone other than SHARP. The warranties set forth herein are in lieu of, and exclusive of, all other warranties, express or implied. ALL EXPRESS AND IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED. SHARP reserves the right to make changes in specifications at any time and without notice. SHARP does not assume any responsibility for the use of any circuitry described; no circuit patent licenses are implied. ® NORTH AMERICA EUROPE ASIA SHARP Electronics Corporation Microelectronics Group 5700 NW Pacific Rim Blvd., M/S 20 Camas, WA 98607, U.S.A. Phone: (360) 834-2500 Telex: 49608472 (SHARPCAM) Facsimile: (360) 834-8903 http://www.sharpmeg.com SHARP Electronics (Europe) GmbH Microelectronics Division Sonninstraße 3 20097 Hamburg, Germany Phone: (49) 40 2376-2286 Telex: 2161867 (HEEG D) Facsimile: (49) 40 2376-2232 SHARP Corporation Integrated Circuits Group 2613-1 Ichinomoto-Cho Tenri-City, Nara, 632, Japan Phone: (07436) 5-1321 Telex: LABOMETA-B J63428 Facsimile: (07436) 5-1532 ©1997 by SHARP Corporation Issued July 1994 Reference Code SMT96105