Click on Series name for product info on aimtec.com Series AM8TW-Z 8Watt | DC-DC Converter FEATURES: Wide 4:1 input range Remote On/Off control High efficiency up to 87% Over Voltage/Overload Protection Operating temperature -40oC to + 85oC Input / Output Isolation 1600 & 3000VDC Continuous short circuit protection Under voltage lockout for 3000VDC models Models Single output Model Input Voltage (V) Output Voltage (V) Output Current max (mA) Isolation (VDC) Max Capacitive Load(uF) Efficiency (%) AM8TW-2403SZ AM8TW-2405SZ AM8TW-2412SZ AM8TW-2415SZ AM8TW-4803SZ AM8TW-4805SZ AM8TW-4812SZ AM8TW-4815SZ 9-36 9-36 9-36 9-36 18-75 18-75 18-75 18-75 3.3 5 12 15 3.3 5 12 15 2000 1500 665 535 2000 1500 665 535 1600 1600 1600 1600 1600 1600 1600 1600 1330 1330 288 200 1330 1330 288 200 83 86 87 87 82 86 87 87 AM8TW-2403SH30Z AM8TW-2405SH30Z AM8TW-2412SH30Z AM8TW-2415SH30Z AM8TW-11003SH30Z AM8TW-11005SH30Z AM8TW-11012SH30Z AM8TW-11015SH30Z 13-70 13-70 13-70 13-70 42-176 42-176 42-176 42-176 3.3 5 12 15 3.3 5 12 15 2000 1500 665 535 2000 1500 665 535 3000 3000 3000 3000 3000 3000 3000 3000 1330 1330 330 220 1330 1330 330 220 83 86 85 86 81 84 84 83 Input Voltage (V) Output Voltage (V) Output Current max (mA) Isolation (VDC) Max Capacitive Load(uF) Efficiency (%) Models Dual output Model AM8TW-2405DZ AM8TW-2412DZ AM8TW-2415DZ AM8TW-4805DZ AM8TW-4812DZ AM8TW-4815DZ 9-36 9-36 9-36 18-75 18-75 18-75 ±5 ±12 ±15 ±5 ±12 ±15 ±800 ±335 ±265 ±800 ±335 ±265 1600 1600 1600 1600 1600 1600 ±900 ±133 ±90 ±900 ±133 ±90 84 86 87 84 87 87 AM8TW-2405DH30Z AM8TW-2412DH30Z AM8TW-2415DH30Z AM8TW-11005DH30Z AM8TW-11012DH30Z AM8TW-11015DH30Z 13-70 13-70 13-70 42-176 42-176 42-176 ±5 ±12 ±15 ±5 ±12 ±15 ±800 ±335 ±265 ±800 ±335 ±265 3000 3000 3000 3000 3000 3000 ±900 ±220 ±100 ±900 ±220 ±100 83 85 86 80 82 83 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. www.aimtec.com F 051e R12.F Tel: +1 514 620 2722 1 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM8TW-Z 8Watt | DC-DC Converter Input Specifications Parameters Voltage range Nominal Typical 24 for 1600VDC models 48 for 1600VDC models 24V or 48V for 3000VDC models 110V Filter Startup time Absolute Maximum Rating For 1600VDC Isolation models For 3000VDC Isolation models 24 for 1600VDC models 48 for 1600VDC models 24V or 48V for 3000VDC models 110V Maximum 9-36 18-75 13-70 42-176 (Pi) Network 20 30 VDC ms -0.7-50 -0.7-100 100 185 100 Peak Input Voltage time On/Off control No Load Input Current Input reflected current Under voltage Lockout (On/Off) Transient recovery time Transient recovery deviation Units ON – 3.0 ~ 12VDC (or open) OFF -0~1.2VDC (or short between pin 1 and 2/3), Idle current 5mA, typ. 15 With 12uH inductance 20 24V or 48V for 3000VDC models On – 12V/ Off – 11.7 110V On – 39.5V/ Off – 38 25% load step change, 1A/us 250 ±3 3.3V output models only ±5 VDC ms mA mAp-p VDC uS % Isolation Specifications Parameters Conditions Tested I/O voltage Tested metal case to Input and Output Resistance 60 sec 60 sec Capacitance Typical Rated Units 1600 & 3000 1000 VDC VDC MOhm >1000 1500 1000 For 1600VDC Isolation models For 3000VDC Isolation models pF Output Specifications Parameters Voltage accuracy Over voltage protection Over load protection Conditions Typical Short Circuit protection Short circuit restart Line voltage regulation Load voltage regulation Cross regulation (Dual) Temperature coefficient Ripple & Noise* Minimum Load Current ±1 ±1.5 48V nom 3000VDC models only Zener Diode Clamp For 1600VDC Isolation models For 3000VDC Isolation models For 3000VDC Isolation models 48V nom Maximu m Units % % 150 160 170 % Continuous Auto-Recovery HL-LL 1600VDC models HL-LL 3000VDC models 0 – 100% load 25% load on one output - 100% load on second load 20MHz Bandwidth ±0.2 ±0.5 ±0.5 ±5 ±0.02 75 0 % of Vin % % %/oC mV p-p % of Max *Measured with 1uF ceramic capacitor. www.aimtec.com F 051e R12.F Tel: +1 514 620 2722 2 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM8TW-Z 8Watt | DC-DC Converter General Specifications Parameters Conditions Switching frequency Operating temperature Storage temperature Maximum case temperature Cooling Humidity Case material Weight Dimensions (L x W x H) MTBF Maximum soldering temperature Typical 100% load 1600VDC models 270 24 & 48V nom 3000VDC models 330 110V 220 Derating above +70 -55 to +125 Maximum Units KHz oC -40 to +85 oC oC 105 Free air convection 95 Nickel plated Cooper 18 1.25 x 0.80 x 0.40 inches 31.80 x 20.30 x 10.20 mm > 1,000,100 hours(MIL-HDBK-217F , Ground Benign, t=+25oC) 1.5mm from case for 10sec 260 % RH g oC Safety Specifications Parameters Pin 1 2 3 9 11 14 16 22 23 Single Remote On/Off -V Input -V Input No Pin N.C. +V Output -V Output +V Input +V Input Dual Remote On/Off -V Input -V Input Common -V Output +V Output Common +V Input +V Input Dimensions 31.80 (1.25) 0.50 (0.02) 1 2 3 11 Bottom View 23 22 2.54 (0.10) Printed Face 9 16 15.20 (0.60) Pin Out Specifications 0.50 (0.02) Standards for 1600VDC models CE (1600VDC models) EN55022 Class A, EN55024 IEC61000-4-2, Perf. Criteria B IEC61000-4-3, Perf. Criteria A IEC61000-4-4, Perf. Criteria B (external 330uF/100V cap required) IEC61000-4-5, Perf. Criteria B (external 330uF/100V cap required) IEC61000-4-6, Perf. Criteria A IEC61000-4-8, Perf. Criteria A Meets IEC/EN60950-1 20.30 (0.80) Agency Approval 14 5.08 (0.20) 3.05 (0.12) 10.20 (0.40) N.C.: Not Connected www.aimtec.com F 051e R12.F Tel: +1 514 620 2722 3 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM8TW-Z 8Watt | DC-DC Converter Derating 70 ºC Output Power (%) 100 80 Safe Operating Area 60 40 20 0 - 20 - 40 0 20 40 60 80 85 100 Ambient Temperature º C Recommended Circuits for 1600VDC isolated models C1 2.2uF, 100V L 12uH C2 2.2uF, 100V C1 330uF, 100V NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R12.F Tel: +1 514 620 2722 4 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only