TI LMV822DRE4 Low-voltage rail-to-rail output operational amplifier Datasheet

LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
FEATURES
•
•
•
•
•
•
•
2.5-V, 2.7-V, and 5-V Performance
–40°C to 125°C Operation
No Crossover Distortion
Low Supply Current at VCC+ = 5 V:
– LMV821…0.3 mA Typ
– LMV822…0.5 mA Typ
– LMV824…1 mA Typ
Rail-to-Rail Output Swing
Gain Bandwidth of 5.5 MHz Typ at 5 V
Slew Rate of 1.9 V/µs Typ at 5 V
DESCRIPTION/
ORDERING INFORMATION
The LMV821 single, LMV822 dual, and LMV824
quad devices are low-voltage (2.5 V to 5.5 V),
low-power
commodity
operational
amplifiers.
Electrical characteristics are very similar to the
LMV3xx operational amplifiers (low supply current,
rail-to-rail outputs, input common-mode range that
includes ground). However, the LMV8xx devices
offer a higher bandwidth (5.5 MHz typical) and faster
slew rate (1.9 V/µs typical).
The LMV8xx devices are cost-effective solutions for
applications
requiring
low-voltage/low-power
operation and space-saving considerations. The
LMV821 is available in the ultra-small DCK package,
which is approximately half the size of SOT-23-5.
The DCK package saves space on printed circuit
boards and enables the design of small portable
electronic devices (cordless and cellular phones,
laptops, PDAs, PCMIA). It also allows the designer
to place the device closer to the signal source to
reduce noise pickup and increase signal integrity.
SLOS434I – FEBRUARY 2004 – REVISED JULY 2006
LMV824 . . . D, DGV, OR PW PACKAGE
(TOP VIEW)
1OUT
1IN−
1IN+
VCC+
2IN+
2IN−
2OUT
1
14
2
13
3
12
4
11
5
10
6
9
7
8
4OUT
4IN−
4IN+
GND/VCC−
3IN+
3IN−
3OUT
LMV822 . . . D OR DGK PACKAGE
(TOP VIEW)
1OUT
1IN −
1IN+
GND/VCC−
1
8
2
7
3
6
4
5
VCC+
2OUT
2IN −
2IN+
LMV821 . . . DBV OR DCK PACKAGE
(TOP VIEW)
IN+
GND/VCC−
IN−
1
5
VCC+
4
OUT
2
3
The LMV8xx devices are characterized for operation
from –40°C to 85°C. The LMV8xxI devices are
characterized for operation from –40°C to 125°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2004–2006, Texas Instruments Incorporated
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434I – FEBRUARY 2004 – REVISED JULY 2006
ORDERING INFORMATION
PACKAGE (1)
TA
SC-70 – DCK
Single
SOT-23 – DBV
SOIC – D
–40°C to 85°C
Dual
MSOP/VSSOP – DGK
SOIC – D
Quad
TSSOP – PW
TVSOP – DGV
SC-70 – DCK
Single
SOT-23 – DBV
SOIC – D
–40°C to 125°C
Dual
MSOP/VSSOP – DGK
SOIC – D
Quad
TSSOP – PW
TVSOP – DGV
(1)
(2)
2
ORDERABLE PART NUMBER
Reel of 3000
LMV821DCKR
Reel of 250
LMV821DCKT
Reel of 3000
LMV821DBVR
Reel of 250
LMV821DBVT
Tube of 75
LMV822D
Reel of 2500
LMV822DR
Tube of 100
LMV822DGK
Reel of 2500
LMV822DGKR
Tube of 50
LMV824D
Reel of 2500
LMV824DR
Tube of 90
LMV824PW
Reel of 2000
LMV824PWR
Reel of 2000
LMV824DGVR
Reel of 3000
LMV821IDCKR
Reel of 250
LMV821IDCKT
Reel of 3000
LMV821IDBVR
Reel of 250
LMV821IDBVT
Tube of 75
LMV822ID
Reel of 2500
LMV822IDR
Tube of 100
LMV822IDGK
Reel of 2500
LMV822IDGKR
Tube of 50
LMV824ID
Reel of 2500
LMV824IDR
Tube of 90
LMV824IPW
Reel of 2000
LMV824IPWR
Reel of 2000
LMV824IDGVR
TOP-SIDE MARKING (2)
RY_
RB8_
MV822
RA_
LMV824
MV824
MV824
RZ_
RB1_
MV822I
R8_
LMV824I
MV824I
MV824I
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
DBV/DCK/DGK: The actual top-side marking has one additional character that designates the assembly/test site.
Submit Documentation Feedback
www.ti.com
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
SLOS434I – FEBRUARY 2004 – REVISED JULY 2006
SYMBOL (EACH AMPLIFIER)
−
IN −
OUT
+
IN +
LMV824 SIMPLIFIED SCHEMATIC
VCC
VBIAS1
+
VCC
−
VBIAS2
VBIAS5
+
+
Output
−
VCC VCC
−
VBIAS3
+
IN−
IN+
VBIAS4−
+
−
Submit Documentation Feedback
3
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434I – FEBRUARY 2004 – REVISED JULY 2006
Absolute Maximum Ratings (1)
over operating free-air temperature range (unless otherwise noted)
MIN
VCC
Supply voltage (2)
VID
Differential input voltage (3)
VI
Input voltage range (either input)
VCC–
Duration of output short circuit (one amplifier) to ground (4)
At or below TA = 25°C, VCC ≤ 5.5 V
D package
θJA
Package thermal impedance (5) (6)
TJ
Operating virtual junction temperature
Tstg
Storage temperature range
(1)
(2)
(3)
(4)
(5)
(6)
MAX
UNIT
5.5
V
±VCC
V
VCC+
V
Unlimited
8 pin
97
14 pin
86
DBV package
206
DCK package
252
DGK package
172
DGV package
127
PW package
113
–65
°C/W
150
°C
150
°C
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating
conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values (except differential voltages and VCC specified for the measurement of IOS) are with respect to the network GND.
Differential voltages are at IN+ with respect to IN–.
Short circuits from outputs to VCC can cause excessive heating and eventual destruction.
Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
The package thermal impedance is calculated in accordance with JESD 51-7.
Recommended Operating Conditions
VCC
TA
4
MIN
MAX
2.5
5
LMV8xxI
–40
125
LMV8xx
–40
85
Supply voltage (single-supply operation)
Operating free-air temperature
Submit Documentation Feedback
UNIT
V
°C
www.ti.com
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
SLOS434I – FEBRUARY 2004 – REVISED JULY 2006
LMV8xx 2.5-V Electrical Characteristics
VCC+ = 2.5 V, VCC– = 0 V, VIC = 1 V, VO = 1.25 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
VIO
TEST CONDITIONS
TA
25°C
Input offset voltage
TYP
MAX
1
3.5
–40°C to 85°C
High level
VCC+ = 2.5 V, RL = 600 Ω to 1.25 V
Low level
VO
LMV8xx
MIN
Output swing
High level
VCC+ = 2.5 V, RL = 2 kΩ to 1.25 V
Low level
4
25°C
2.3
–40°C to 85°C
2.2
25°C
0.13
0.2
0.3
2.4
–40°C to 85°C
2.3
25°C
mV
2.37
–40°C to 85°C
25°C
UNIT
2.46
0.08
–40°C to 85°C
V
0.12
0.2
LMV8xxI 2.5-V Electrical Characteristics
VCC+ = 2.5 V, VCC– = 0 V, VIC = 1 V, VO = 1.25 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
VIO
TEST CONDITIONS
TA
25°C
Input offset voltage
TYP
MAX
1
3.5
–40°C to 125°C
High level
VCC+ = 2.5 V, RL = 600 Ω to 1.25 V
Low level
VO
LMV8xxI
MIN
Output swing
High level
VCC+ = 2.5 V, RL = 2 kΩ to 1.25 V
Low level
5.5
25°C
2.28
–40°C to 125°C
2.18
25°C
0.13
–40°C to 125°C
2.28
25°C
–40°C to 125°C
Submit Documentation Feedback
0.22
0.32
2.38
mV
2.37
–40°C to 125°C
25°C
UNIT
2.46
0.08
V
0.14
0.22
5
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434I – FEBRUARY 2004 – REVISED JULY 2006
LMV8xx 2.7-V Electrical Characteristics
VCC+ = 2.7 V, VCC– = 0 V, VIC = 1 V, VO = 1.35 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Average temperature coefficient
of input offset voltage
IIB
Input bias current
IIO
Input offset current
CMRR Common-mode rejection ratio
TEST CONDITIONS
TA
25°C
25°C
30
–40°C to 85°C
25°C
0.5
–40°C to 85°C
VIC = 0 to 1.7 V
25°C
70
68
–40°C to 85°C
70
–kSVR
Negative supply-voltage
rejection ratio
VCC+ = 1.7 V, VCC– = –1 V to –3.3 V,
VO = 0, VIC = 0
25°C
73
–40°C to 85°C
70
VICR
Common-mode input
voltage range
CMRR ≥ 50 dB
RL = 600 Ω to 1.35 V,
VO = 1.35 V to 2.2 V
Sourcing
RL = 600 Ω to 1.35 V,
VO = 1.35 V to 0.5 V
Sinking
RL = 2 kΩ to 1.35 V,
VO = 1.35 V to 2.2 V
Sourcing
RL = 2 kΩ to 1.35 V,
VO = 1.35 V to 0.5 V
Sinking
High level
VCC+ = 2.7 V,
RL = 600 Ω to 1.35 V
Low level
Output swing
High level
VCC+ = 2.7 V,
RL = 2 kΩ to 1.35 V
Low level
ICC
Supply current
–0.3
to 2
100
25°C
90
–40°C to 85°C
85
25°C
85
–40°C to 85°C
80
25°C
95
90
–40°C to 85°C
85
25°C
2.5
–40°C to 85°C
2.4
25°C
2.58
0.13
2.6
–40°C to 85°C
2.5
25°C
2.66
0.08
–40°C to 85°C
16
VO = 2.7 V
Sinking
25°C
12
26
0.22
–40°C to 85°C
Submit Documentation Feedback
V
0.12
0.2
12
mA
0.3
0.5
0.45
–40°C to 85°C
25°C
0.2
0.3
25°C
–40°C to 85°C
dB
95
25°C
LMV824 (all four amplifiers)
V
100
Sourcing
LMV822 (both amplifiers)
dB
90
–40°C to 85°C
25°C
nA
90
25°C
25°C
nA
dB
85
–0.2
to 1.9
mV
dB
85
VO = 0 V
LMV821
30
85
25°C
–40°C to 85°C
90
50
–40°C to 85°C
UNIT
µV/°C
140
75
Output current
3.5
1
25°C
IO
1
25°C
VCC+ = 1.7 V to 4 V, VCC– = –1 V,
VO = 0, VIC = 0
VO
MAX
4
Positive supply-voltage
rejection ratio
Large-signal voltage
amplification
TYP
–40°C to 85°C
+kSVR
AV
6
LMV8xx
MIN
0.6
0.8
0.72
1
1.2
mA
www.ti.com
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
SLOS434I – FEBRUARY 2004 – REVISED JULY 2006
LMV8xx 2.7-V Electrical Characteristics (continued)
VCC+ = 2.7 V, VCC– = 0 V, VIC = 1 V, VO = 1.35 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
LMV8xx
MIN
TYP
MAX
UNIT
SR
Slew rate (1)
25°C
1.7
V/µs
GBW
Gain bandwidth product
(2)
25°C
5
MHz
Φm
Phase margin
(2)
25°C
60
deg
Gain margin
(2)
25°C
8.6
dB
135
dB
Amplifier-to-amplifier isolation
VCC+ = 5 V, RL = 100 kΩ to 2.5 V (3)
25°C
Vn
Equivalent input noise voltage
f = 1 kHz, VIC = 1 V
25°C
45
nV/√Hz
In
Equivalent input noise current
f = 1 kHz
25°C
0.18
pA/√Hz
Total harmonic distortion
f = 1 kHz, AV = –2, RL = 10 kΩ,
VO = 4.1 Vp-p
25°C
0.01
%
THD
(1)
(2)
(3)
Connected as voltage follower with 1-V step input. Value specified is the slower of the positive and negative slew rates.
40-dB closed-loop dc gain, CL = 22 pF
Each amplifier excited in turn with 1 kHz to produce VO = 3 Vp-p
Submit Documentation Feedback
7
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434I – FEBRUARY 2004 – REVISED JULY 2006
LMV8xxI 2.7-V Electrical Characteristics
VCC+ = 2.7 V, VCC– = 0 V, VIC = 1 V, VO = 1.35 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Average temperature coefficient
of input offset voltage
IIB
Input bias current
IIO
Input offset current
CMRR Common-mode rejection ratio
TEST CONDITIONS
LMV8xxI
MIN
25°C
25°C
30
–40°C to 125°C
25°C
0.5
–40°C to 125°C
VIC = 0 to 1.7 V
25°C
70
68
–40°C to 125°C
70
–kSVR
Negative supply-voltage
rejection ratio
VCC+ = 1.7 V, VCC– = –1 V to –3.3 V,
VO = 0, VIC = 0
25°C
73
–40°C to 125°C
70
VICR
Common-mode input
voltage range
CMRR ≥ 50 dB
RL = 600 Ω to 1.35 V,
VO = 1.35 V to 2.2 V
Sourcing
RL = 600 Ω to 1.35 V,
VO = 1.35 V to 0.5 V
Sinking
RL = 2 kΩ to 1.35 V,
VO = 1.35 V to 2.2 V
Sourcing
RL = 2 kΩ to 1.35 V,
VO = 1.35 V to 0.5 V
Sinking
High level
VCC+ = 2.7 V,
RL = 600 Ω to 1.35 V
Low level
Output swing
High level
VCC+ = 2.7 V,
RL = 2 kΩ to 1.35 V
Low level
ICC
Supply current
–0.3
to 2
100
25°C
90
–40°C to 125°C
85
25°C
85
–40°C to 125°C
80
25°C
95
–40°C to 125°C
90
25°C
90
–40°C to 125°C
85
25°C
2.5
–40°C to 125°C
2.4
25°C
2.58
2.5
25°C
0.08
–40°C to 125°C
16
VO = 2.7 V
Sinking
25°C
12
26
0.22
–40°C to 125°C
Submit Documentation Feedback
0.12
mA
0.3
0.5
0.45
–40°C to 125°C
25°C
V
0.2
12
–40°C to 125°C
0.2
2.66
25°C
LMV824 (all four amplifiers)
dB
95
Sourcing
LMV822 (both amplifiers)
V
0.3
–40°C to 125°C
25°C
dB
100
0.13
2.6
nA
90
–40°C to 125°C
25°C
nA
dB
85
–0.2
to 1.9
mV
dB
85
25°C
25°C
30
85
VO = 0 V
LMV821
90
50
–40°C to 125°C
UNIT
µV/°C
140
75
Output current
3.5
1
25°C
IO
1
25°C
VCC+ = 1.7 V to 4 V, VCC– = –1 V,
VO = 0, VIC = 0
VO
MAX
5.5
Positive supply-voltage
rejection ratio
Large-signal voltage
amplification
TYP
–40°C to 125°C
+kSVR
AV
8
TA
0.6
0.8
0.72
1
1.2
mA
www.ti.com
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
SLOS434I – FEBRUARY 2004 – REVISED JULY 2006
LMV8xxI 2.7-V Electrical Characteristics (continued)
VCC+ = 2.7 V, VCC– = 0 V, VIC = 1 V, VO = 1.35 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
LMV8xxI
MIN
TYP
MAX
UNIT
SR
Slew rate (1)
25°C
1.7
V/µs
GBW
Gain bandwidth product
(2)
25°C
5
MHz
Φm
Phase margin
(2)
25°C
60
deg
Gain margin
(2)
25°C
8.6
dB
135
dB
Amplifier-to-amplifier isolation
VCC+ = 5 V, RL = 100 kΩ to 2.5 V (3)
25°C
Vn
Equivalent input noise voltage
f = 1 kHz, VIC = 1 V
25°C
45
nV/√Hz
In
Equivalent input noise current
f = 1 kHz
25°C
0.18
pA/√Hz
Total harmonic distortion
f = 1 kHz, AV = –2, RL = 10 kΩ,
VO = 4.1 Vp-p
25°C
0.01
%
THD
(1)
(2)
(3)
Connected as voltage follower with 1-V step input. Value specified is the slower of the positive and negative slew rates.
40-dB closed-loop dc gain, CL = 22 pF
Each amplifier excited in turn with 1 kHz to produce VO = 3 Vp-p
Submit Documentation Feedback
9
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434I – FEBRUARY 2004 – REVISED JULY 2006
LMV8xx 5-V Electrical Characteristics
VCC+ = 5 V, VCC– = 0 V, VIC = 2 V, VO = 2.5 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Average temperature coefficient
of input offset voltage
IIB
Input bias current
IIO
Input offset current
CMRR Common-mode rejection ratio
TEST CONDITIONS
TA
LMV8xx
MIN
25°C
1
25°C
40
–40°C to 85°C
25°C
0.5
–40°C to 85°C
VIC = 0 to 4 V
25°C
72
70
75
–40°C to 85°C
70
–kSVR
Negative supply-voltage
rejection ratio
VCC+ = 1.7 V, VCC– = –1 V to –3.3 V,
VO = 0, VIC = 0
25°C
73
–40°C to 85°C
70
VICR
Common-mode input
voltage range
CMRR ≥ 50 dB
RL = 600 Ω to 2.5 V,
VO = 2.5 V to 4.5 V
Sourcing
RL = 600 Ω to 2.5 V,
VO = 2.5 V to 0.5 V
Sinking
RL = 2 kΩ to 2.5 V,
VO = 2.5 V to 4.5 V
Sourcing
RL = 2 kΩ to 2.5 V,
VO = 2.5 V to 0.5 V
Sinking
High level
VCC+ = 5 V,
RL = 600 Ω to 2.5 V
Low level
Output swing
High level
VCC+ = 5 V,
RL = 2 kΩ to 2.5 V
Low level
VO = 0 V
Sourcing
VO = 5 V
Sinking
Output current
LMV821
ICC
Supply current
95
90
25°C
95
–40°C to 85°C
90
25°C
95
LMV822 (both amplifiers)
95
–40°C to 85°C
90
25°C
4.75
–40°C to 85°C
4.7
25°C
Submit Documentation Feedback
dB
105
4.84
0.17
0.25
0.3
25°C
4.85
–40°C to 85°C
4.8
25°C
4.9
0.1
–40°C to 85°C
V
0.15
0.2
25°C
20
–40°C to 85°C
15
25°C
20
–40°C to 85°C
15
45
mA
40
0.3
0.4
0.6
0.5
–40°C to 85°C
–40°C to 85°C
V
105
–40°C to 85°C
25°C
dB
90
25°C
25°C
nA
105
–40°C to 85°C
LMV824 (all four amplifiers)
10
105
25°C
–40°C to 85°C
nA
dB
85
–0.3
to 4.3
mV
dB
85
–0.2
to 4.2
25°C
30
90
25°C
–40°C to 85°C
100
50
–40°C to 85°C
UNIT
µV/°C
150
25°C
IO
3.5
25°C
VCC+ = 1.7 V to 4 V, VCC– = –1 V,
VO = 0, VIC = 0
VO
1
4
Positive supply-voltage
rejection ratio
Large-signal voltage
amplification
MAX
–40°C to 85°C
+kSVR
AV
TYP
0.7
0.9
1
1.3
1.5
mA
www.ti.com
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
SLOS434I – FEBRUARY 2004 – REVISED JULY 2006
LMV8xx 5-V Electrical Characteristics (continued)
VCC+ = 5 V, VCC– = 0 V, VIC = 2 V, VO = 2.5 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC+ = 5 V (1)
TA
25°C
LMV8xx
MIN
TYP
1.4
MAX
UNIT
SR
Slew rate
1.9
V/µs
GBW
Gain bandwidth product
(2)
25°C
5.5
MHz
Φm
Phase margin
(2)
25°C
64.2
deg
Gain margin
(2)
25°C
8.7
dB
135
dB
Amplifier-to-amplifier isolation
VCC+ = 5 V, RL = 100 kΩ to 2.5 V (3)
25°C
Vn
Equivalent input noise voltage
f = 1 kHz, VIC = 1 V
25°C
42
nV/√Hz
In
Equivalent input noise current
f = 1 kHz
25°C
0.2
pA/√Hz
Total harmonic distortion
f = 1 kHz, AV = –2, RL = 10 kΩ,
VO = 4.1 Vp-p
25°C
0.01
%
THD
(1)
(2)
(3)
Connected as voltage follower with 3-V step input. Value specified is the slower of the positive and negative slew rates.
40-dB closed-loop dc gain, CL = 22 pF
Each amplifier excited in turn with 1 kHz to produce VO = 3 Vp-p
Submit Documentation Feedback
11
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434I – FEBRUARY 2004 – REVISED JULY 2006
LMV8xxI 5-V Electrical Characteristics
VCC+ = 5 V, VCC– = 0 V, VIC = 2 V, VO = 2.5 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Average temperature coefficient
of input offset voltage
IIB
Input bias current
IIO
Input offset current
CMRR Common-mode rejection ratio
TEST CONDITIONS
TA
LMV8xxI
MIN
25°C
1
25°C
40
–40°C to 125°C
25°C
0.5
–40°C to 125°C
VIC = 0 to 4 V
25°C
72
70
75
–40°C to 125°C
70
–kSVR
Negative supply-voltage
rejection ratio
VCC+ = 1.7 V, VCC– = –1 V to –3.3 V,
VO = 0, VIC = 0
25°C
73
–40°C to 125°C
70
VICR
Common-mode input
voltage range
CMRR ≥ 50 dB
RL = 600 Ω to 2.5 V,
VO = 2.5 V to 4.5 V
Sourcing
RL = 600 Ω to 2.5 V,
VO = 2.5 V to 0.5 V
Sinking
RL = 2 kΩ to 2.5 V,
VO = 2.5 V to 4.5 V
Sourcing
RL = 2 kΩ to 2.5 V,
VO = 2.5 V to 0.5 V
Sinking
High level
VCC+ = 5 V,
RL = 600 Ω to 2.5 V
Low level
Output swing
High level
VCC+ = 5 V,
RL = 2 kΩ to 2.5 V
Low level
VO = 0 V
Sourcing
VO = 5 V
Sinking
Output current
LMV821
ICC
Supply current
LMV824 (all four amplifiers)
12
–0.3
to 4.3
105
25°C
95
–40°C to 125°C
90
25°C
95
–40°C to 125°C
90
25°C
95
–40°C to 125°C
90
25°C
95
–40°C to 125°C
90
25°C
4.75
–40°C to 125°C
4.6
25°C
4.8
25°C
4.84
V
0.15
0.2
20
–40°C to 125°C
15
25°C
20
–40°C to 125°C
15
45
mA
40
0.3
0.4
0.6
0.5
–40°C to 125°C
Submit Documentation Feedback
0.25
4.9
0.1
25°C
–40°C to 125°C
dB
105
–40°C to 125°C
25°C
V
0.3
–40°C to 125°C
25°C
dB
105
0.17
4.85
nA
105
–40°C to 125°C
25°C
nA
dB
85
–0.2
to 4.2
mV
dB
85
–40°C to 125°C
LMV822 (both amplifiers)
30
90
25°C
25°C
100
50
–40°C to 125°C
UNIT
µV/°C
150
25°C
IO
3.5
25°C
VCC+ = 1.7 V to 4 V, VCC– = –1 V,
VO = 0, VIC = 0
VO
1
5.5
Positive supply-voltage
rejection ratio
Large-signal voltage
amplification
MAX
–40°C to 125°C
+kSVR
AV
TYP
0.7
0.9
1
1.3
1.5
mA
www.ti.com
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
SLOS434I – FEBRUARY 2004 – REVISED JULY 2006
LMV8xxI 5-V Electrical Characteristics (continued)
VCC+ = 5 V, VCC– = 0 V, VIC = 2 V, VO = 2.5 V, and RL > 1 MΩ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC+ = 5 V (1)
TA
25°C
LMV8xxI
MIN
TYP
1.4
MAX
UNIT
SR
Slew rate
1.9
V/µs
GBW
Gain bandwidth product
(2)
25°C
5.5
MHz
Φm
Phase margin
(2)
25°C
64.2
deg
Gain margin
(2)
25°C
8.7
dB
135
dB
Amplifier-to-amplifier isolation
VCC+ = 5 V, RL = 100 kΩ to 2.5 V (3)
25°C
Vn
Equivalent input noise voltage
f = 1 kHz, VIC = 1 V
25°C
42
nV/√Hz
In
Equivalent input noise current
f = 1 kHz
25°C
0.2
pA/√Hz
Total harmonic distortion
f = 1 kHz, AV = –2, RL = 10 kΩ,
VO = 4.1 Vp-p
25°C
0.01
%
THD
(1)
(2)
(3)
Connected as voltage follower with 3-V step input. Value specified is the slower of the positive and negative slew rates.
40-dB closed-loop dc gain, CL = 22 pF
Each amplifier excited in turn with 1 kHz to produce VO = 3 Vp-p
Submit Documentation Feedback
13
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434I – FEBRUARY 2004 – REVISED JULY 2006
TYPICAL CHARACTERISTICS
TA = 25°C, VCC+ = 5-V Single Supply (Unless Otherwise Noted)
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
1200
INPUT CURRENT
vs
TEMPERATURE
−30
LMV824
All Channels
VCC+ = 5 V
Vin = VCC+/2
TA = 855C
−40
II − Input Current − nA
ICC − Supply Current − µA
1000
TA = 255C
800
600
TA = −405C
400
−50
−60
200
−70
−40
0
0
1
2
3
4
VCC+ − Supply Voltage − V
5
6
80
100
0.01
0.1
1
Output Voltage Referenced to V+ − (V)
10
Figure 2.
SOURCING CURRENT
vs
OUTPUT VOLTAGE
SOURCING CURRENT
vs
OUTPUT VOLTAGE
100
VCC+ = 2.7 V
VCC+ = 5 V
IO − Source Current − mA
10
1
0.1
0.01
0.001
0.01
0.1
1
Output Voltage Referenced to V+ − (V)
10
10
1
0.1
0.01
0.001
Figure 3.
14
0
20
40
60
TA − Temperature − °C
Figure 1.
100
IO − Source Current − mA
−20
Figure 4.
Submit Documentation Feedback
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434I – FEBRUARY 2004 – REVISED JULY 2006
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V Single Supply (Unless Otherwise Noted)
SINKING CURRENT
vs
OUTPUT VOLTAGE
SINKING CURRENT
vs
OUTPUT VOLTAGE
100
100
VCC+ = 2.7 V
VCC+ = 5 V
10
IO − Sink Current − mA
IO − Sink Current − mA
10
1
1
0.1
0.1
0.01
0.01
0.1
0.01
1
10
Output Voltage Referenced to GND − V
Figure 5.
Figure 6.
OUTPUT VOLTAGE SWING
vs
SUPPLY VOLTAGE
OUTPUT VOLTAGE SWING
vs
SUPPLY VOLTAGE
RL = 2 kΩ to Mid Rail
Output Voltage From Supply Voltage − mV
Output Voltage From Supply Voltage − mV
10
80
RL = 10 kΩ to Mid Rail
40
30
Negative Swing
20
0
2.6
1
Output Voltage Referenced to GND − V
50
10
0.1
0.01
Positive Swing
3
3.4
3.8
4.2
4.6
5
70
60
50
Negative Swing
40
Positive Swing
30
20
10
0
2.6
VCC+ − Supply Voltage − V
Figure 7.
3
3.4
3.8
4.2
VCC+ − Supply Voltage − V
4.6
5
Figure 8.
Submit Documentation Feedback
15
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434I – FEBRUARY 2004 – REVISED JULY 2006
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V Single Supply (Unless Otherwise Noted)
OUTPUT VOLTAGE SWING
vs
SUPPLY VOLTAGE
160
RL = 600 Ω to Mid Rail
Output Voltage From Supply Voltage − mV
Output Voltage From Supply Voltage − mV
160
OUTPUT VOLTAGE SWING
vs
LOAD RESISTANCE
150
140
Negative Swing
130
120
110
Positive Swing
100
90
80
70
60
2.6
RlL = 5 kΩ to Mid Rail
VCC+ = 5 V
140
120
100
80
60
40
20
0
3
3.4
3.8
4.2
4.6
100
5
VCC+ − Supply Voltage − V
1000
10k
Resistive Load − Ω
Figure 9.
Figure 10.
CROSSTALK REJECTION
vs
FREQUENCY
+PSRR
vs
FREQUENCY
100
160
100k
VCC+ = +2.5 V
90
150
140
70
VCC+ = +1.35 V
PSRR − dB
Crosstalk Rejection − dB
80
130
120
110
100
90
100
60
50
40
30
VCC+ = ±2.5 V
VI = 3 VPP
RL = 5 kΩ
AV = 1
20
10
1k
10k
100k
0
100
Frequency − Hz
Figure 11.
16
1k
10k
Frequency − Hz
Figure 12.
Submit Documentation Feedback
100k
1M
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434I – FEBRUARY 2004 – REVISED JULY 2006
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V Single Supply (Unless Otherwise Noted)
–PSRR
vs
FREQUENCY
100
VCC+ = +2.5 V
90
80
PSRR − dB
70
60 VCC+ = +1.35 V
50
40
30
20
10
0
100
1k
10k
100k
Frequency − Hz
1M
Figure 13.
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 2.7 V, RL = 600 Ω, 2 kΩ, 100 kΩ)
80
140
Gain − dB
Phase
60
100
50
80
40
60
30
40
Gain
20
20
0
10
VCC+ = 2.7 V
600 Ω
2 kΩ
100 kΩ
0
−10
−20
−40
−20
1k
Phase Margin − Deg
120
70
10k
100k
1M
−60
10M
Frequency − Hz
Figure 14.
Submit Documentation Feedback
17
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434I – FEBRUARY 2004 – REVISED JULY 2006
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V Single Supply (Unless Otherwise Noted)
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 5 V, RL = 600 Ω, 2 kΩ, 100 kΩ)
80
140
70
120
100
Phase
50
80
40
60
30
40
20
20
Gain
0
10
−10
−20
−20
VCC+ = 5 V
600 Ω
2 kΩ
100 kΩ
0
1k
Phase Margin − Deg
Gain − dB
60
−40
10k
100k
Frequency − Hz
1M
−60
10M
Figure 15.
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 2.7 V, RL = 10 kΩ, CL = 22 pF, 100 pF, 200 pF)
80
100
70
Gain − dB
60
60
50
40
40
20
30
0
20
−20
Gain
−40
10
VCC+ = 2.7 V
RL = 10 kΩ
22 pF
100 pF
200 pF
0
−10
−60
−80
−20
1k
10k
100k
Frequency − Hz
Figure 16.
18
Submit Documentation Feedback
1M
−100
10M
Phase Margin − Deg
80
Phase
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434I – FEBRUARY 2004 – REVISED JULY 2006
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V Single Supply (Unless Otherwise Noted)
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 5 V, RL = 10 kΩ, CL = 22 pF, 100 pF, 200 pF)
80
100
80
70
Phase
60
50
40
40
20
0
30
Gain
−20
20
10
0
−10
−20
−40
VCC+ = 5 V
RL = 10 kΩ
22 pF
100 pF
200 pF
1k
Phase Margin − Deg
Gain − dB
60
−60
−80
10k
100k
1M
−100
10M
Frequency − Hz
Figure 17.
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 2.7 V, RL = 600 Ω, CL = 22 pF, 100 pF, 200 pF)
80
140
70
120
Phase
100
50
80
40
60
30
40
20
20
Gain
VCC+ = 2.7 V
RL = 600 Ω
10
0
−20
22 pF
100 pF
200 pF
−10
−20
0
1k
Phase Margin − Deg
Gain − dB
60
−40
10k
100k
1M
−60
10M
Frequency − Hz
Figure 18.
Submit Documentation Feedback
19
LMV821 SINGLE, LMV822 DUAL, LMV824 QUAD
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
www.ti.com
SLOS434I – FEBRUARY 2004 – REVISED JULY 2006
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VCC+ = 5-V Single Supply (Unless Otherwise Noted)
GAIN AND PHASE MARGIN
vs
FREQUENCY
(VCC+ = 5 V, RL = 600 Ω, CL = 22 pF, 100 pF, 200 pF)
80
140
70
120
Phase
100
50
80
40
60
40
30
Gain
20
20
10
0
−20
22 pF
100 pF
200 pF
−10
−20
0
VCC+ = 5 V
RL = 600 Ω
1k
−40
10k
100k
Frequency − Hz
Figure 19.
20
Submit Documentation Feedback
1M
−60
10M
Phase Margin − Deg
Gain − dB
60
PACKAGE OPTION ADDENDUM
www.ti.com
18-Sep-2008
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
LMV821DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821DBVRE4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821DBVTE4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821DCKR
ACTIVE
SC70
DCK
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821DCKRE4
ACTIVE
SC70
DCK
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821DCKRG4
ACTIVE
SC70
DCK
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821DCKT
ACTIVE
SC70
DCK
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821DCKTE4
ACTIVE
SC70
DCK
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821DCKTG4
ACTIVE
SC70
DCK
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821IDBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821IDBVRE4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821IDBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821IDBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821IDBVTE4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821IDBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821IDCKR
ACTIVE
SC70
DCK
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821IDCKRE4
ACTIVE
SC70
DCK
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821IDCKRG4
ACTIVE
SC70
DCK
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821IDCKT
ACTIVE
SC70
DCK
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821IDCKTE4
ACTIVE
SC70
DCK
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV821IDCKTG4
ACTIVE
SC70
DCK
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822D
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Addendum-Page 1
Lead/Ball Finish
MSL Peak Temp (3)
PACKAGE OPTION ADDENDUM
www.ti.com
18-Sep-2008
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
LMV822DE4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822DG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822DGKR
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822DGKRG4
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822DR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822DRE4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822DRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822ID
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822IDE4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822IDG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822IDGKR
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822IDGKRG4
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822IDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822IDRE4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV822IDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824D
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824DE4
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824DG4
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824DGVR
ACTIVE
TVSOP
DGV
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824DGVRE4
ACTIVE
TVSOP
DGV
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824DGVRG4
ACTIVE
TVSOP
DGV
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824DR
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824DRE4
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824DRG4
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824ID
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824IDE4
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Addendum-Page 2
Lead/Ball Finish
MSL Peak Temp (3)
PACKAGE OPTION ADDENDUM
www.ti.com
18-Sep-2008
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
LMV824IDG4
ACTIVE
SOIC
D
14
LMV824IDGVR
ACTIVE
TVSOP
DGV
LMV824IDGVRE4
ACTIVE
TVSOP
LMV824IDGVRG4
ACTIVE
LMV824IDR
50
Lead/Ball Finish
MSL Peak Temp (3)
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
DGV
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TVSOP
DGV
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824IDRE4
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824IDRG4
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824IPW
ACTIVE
TSSOP
PW
14
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824IPWE4
ACTIVE
TSSOP
PW
14
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824IPWG4
ACTIVE
TSSOP
PW
14
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824IPWR
ACTIVE
TSSOP
PW
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824IPWRE4
ACTIVE
TSSOP
PW
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824IPWRG4
ACTIVE
TSSOP
PW
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824PW
ACTIVE
TSSOP
PW
14
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824PWE4
ACTIVE
TSSOP
PW
14
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824PWG4
ACTIVE
TSSOP
PW
14
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824PWR
ACTIVE
TSSOP
PW
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824PWRE4
ACTIVE
TSSOP
PW
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LMV824PWRG4
ACTIVE
TSSOP
PW
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
Addendum-Page 3
PACKAGE OPTION ADDENDUM
www.ti.com
18-Sep-2008
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LMV821, LMV822 :
• Automotive: LMV821-Q1, LMV822-Q1
NOTE: Qualified Version Definitions:
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 4
PACKAGE MATERIALS INFORMATION
www.ti.com
30-Jul-2010
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
LMV821DBVR
SOT-23
DBV
5
3000
180.0
9.2
LMV821DBVR
SOT-23
DBV
5
3000
178.0
LMV821DBVT
SOT-23
DBV
5
250
178.0
LMV821DBVT
SOT-23
DBV
5
250
LMV821DCKR
SC70
DCK
5
W
Pin1
(mm) Quadrant
3.23
3.17
1.37
4.0
8.0
Q3
9.0
3.23
3.17
1.37
4.0
8.0
Q3
9.0
3.23
3.17
1.37
4.0
8.0
Q3
180.0
9.2
3.23
3.17
1.37
4.0
8.0
Q3
3000
180.0
9.2
2.24
2.34
1.22
4.0
8.0
Q3
LMV821DCKT
SC70
DCK
5
250
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
LMV821IDBVR
SOT-23
DBV
5
3000
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LMV821IDBVT
SOT-23
DBV
5
250
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LMV821IDCKT
SC70
DCK
5
250
178.0
9.0
2.4
2.5
1.2
4.0
8.0
Q3
LMV822DGKR
MSOP
DGK
8
2500
330.0
12.4
5.3
3.3
1.3
8.0
12.0
Q1
LMV822DR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
LMV822IDGKR
MSOP
DGK
8
2500
330.0
12.4
5.3
3.3
1.3
8.0
12.0
Q1
LMV822IDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
LMV824DGVR
TVSOP
DGV
14
2000
330.0
12.4
6.8
4.0
1.6
8.0
12.0
Q1
LMV824DR
SOIC
D
14
2500
330.0
16.4
6.5
9.0
2.1
8.0
16.0
Q1
LMV824IDGVR
TVSOP
DGV
14
2000
330.0
12.4
6.8
4.0
1.6
8.0
12.0
Q1
LMV824IDR
SOIC
D
14
2500
330.0
16.4
6.5
9.0
2.1
8.0
16.0
Q1
LMV824IPWR
TSSOP
PW
14
2000
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
30-Jul-2010
Device
LMV824PWR
Package Package Pins
Type Drawing
TSSOP
PW
14
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2000
330.0
12.4
6.9
B0
(mm)
K0
(mm)
P1
(mm)
5.6
1.6
8.0
W
Pin1
(mm) Quadrant
12.0
Q1
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LMV821DBVR
SOT-23
DBV
5
3000
205.0
200.0
33.0
LMV821DBVR
SOT-23
DBV
5
3000
180.0
180.0
18.0
LMV821DBVT
SOT-23
DBV
5
250
180.0
180.0
18.0
LMV821DBVT
SOT-23
DBV
5
250
205.0
200.0
33.0
LMV821DCKR
SC70
DCK
5
3000
205.0
200.0
33.0
LMV821DCKT
SC70
DCK
5
250
180.0
180.0
18.0
LMV821IDBVR
SOT-23
DBV
5
3000
203.0
203.0
35.0
LMV821IDBVT
SOT-23
DBV
5
250
203.0
203.0
35.0
LMV821IDCKT
SC70
DCK
5
250
180.0
180.0
18.0
LMV822DGKR
MSOP
DGK
8
2500
346.0
346.0
35.0
LMV822DR
SOIC
D
8
2500
340.5
338.1
20.6
LMV822IDGKR
MSOP
DGK
8
2500
370.0
355.0
55.0
LMV822IDR
SOIC
D
8
2500
340.5
338.1
20.6
LMV824DGVR
TVSOP
DGV
14
2000
346.0
346.0
29.0
LMV824DR
SOIC
D
14
2500
346.0
346.0
33.0
LMV824IDGVR
TVSOP
DGV
14
2000
346.0
346.0
29.0
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
30-Jul-2010
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LMV824IDR
SOIC
D
14
2500
346.0
346.0
33.0
LMV824IPWR
TSSOP
PW
14
2000
346.0
346.0
29.0
LMV824PWR
TSSOP
PW
14
2000
346.0
346.0
29.0
Pack Materials-Page 3
MECHANICAL DATA
MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000
DGV (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
24 PINS SHOWN
0,40
0,23
0,13
24
13
0,07 M
0,16 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
0°–8°
1
0,75
0,50
12
A
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,08
14
16
20
24
38
48
56
A MAX
3,70
3,70
5,10
5,10
7,90
9,80
11,40
A MIN
3,50
3,50
4,90
4,90
7,70
9,60
11,20
DIM
4073251/E 08/00
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side.
Falls within JEDEC: 24/48 Pins – MO-153
14/16/20/56 Pins – MO-194
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DLP® Products
www.dlp.com
Communications and
Telecom
www.ti.com/communications
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
www.ti.com/clocks
Consumer Electronics
www.ti.com/consumer-apps
Interface
interface.ti.com
Energy
www.ti.com/energy
Logic
logic.ti.com
Industrial
www.ti.com/industrial
Power Mgmt
power.ti.com
Medical
www.ti.com/medical
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
www.ti.com/video
Wireless
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated