MICROWAVE CORPORATION HMC337 v01.0803 GaAs MMIC SUB-HARMONICALLY PUMPED MIXER, 17 - 25 GHz Typical Applications Features The HMC337 is ideal for: Integrated LO Amplifier: -5 dBm Input • 18 and 23 GHz Microwave Radios Sub-Harmonically Pumped (x2) LO • Up and Down Converter for Point to Point Radios High 2LO/RF Isolation: > 25 dB Small Size: 0.97mm x 1.32mm • Satellite Communication Systems Functional Diagram General Description The HMC337 chip is a sub-harmonically pumped (x2) MMIC mixer with an integrated LO amplifier which can be used as an upconverter or downconverter. The chip utilizes a GaAs PHEMT technology that results in a small overall chip area of 1.28mm2. The 2LO to RF isolation is excellent eliminating the need for additional filtering. The LO amplifier is a single bias (+3V to +4V) two stage design with only -5 dBm nominal drive requirement. All data is measured with the chip in a 50 ohm test fixture connected via 0.076 mm (3 mil) ribbon bonds of minimal length <0.31 mm (<12 mils). MIXERS - CHIP 5 Electrical Specifications, TA = +25° C, As a Function of Vdd IF = 1 GHz LO = -5 dBm & Vdd = +4V Parameter Min. Typ. IF = 1 GHz LO = -5 dBm & Vdd = +3V Max. Min. Typ. Units Max. Frequency Range, RF 17 - 25 18 - 24 GHz Frequency Range, LO 8.5 - 12.5 9 - 12 GHz Frequency Range, IF DC - 3 DC - 3 GHz Conversion Loss 9 13 9 13 dB Noise Figure (SSB) 9 13 9 13 dB 2LO to RF Isolation 10 25 - 30 10 25 - 30 dB 2LO to IF Isolation 27 40 - 50 30 40 - 50 dB IP3 (Input) 3 10 2 9 dBm 1 dB Compression (Input) -5 0 -6 -1 dBm 25 mA Supply Current (Idd) 28 * Unless otherwise noted, all measurements performed as downconverter, IF= 1 GHz. 5 - 94 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com HMC337 v01.0803 MICROWAVE CORPORATION GaAs MMIC SUB-HARMONICALLY PUMPED MIXER, 17 - 25 GHz Conversion Gain vs. Temperature @ LO = -5 dBm, Vdd= +3V 0 0 -4 -4 CONVERSION GAIN (dB) -8 -12 + 25 C + 85 C -16 - 55 C -20 -8 -12 + 25 C + 85 C - 55 C -16 -20 16 17 18 19 20 21 22 23 24 25 26 16 17 18 19 FREQUENCY (GHz) 0 0 -4 -4 -8 -12 - 7 dBm - 5 dBm - 3 dBm -20 22 23 24 25 26 23 24 25 26 -8 -12 -7 dBm -5 dBm -3 dBm -16 5 -20 16 17 18 19 20 21 22 23 24 25 26 16 17 18 19 FREQUENCY (GHz) 20 21 22 FREQUENCY (GHz) Isolation @ LO = -5 dBm, Vdd = +4V Isolation @ LO = -5 dBm, Vdd = +3V 0 0 -10 -10 ISOLATION (dB) ISOLATION (dB) 21 Conversion Gain vs. LO Drive @ Vdd = +3V CONVERSION GAIN (dB) CONVERSION GAIN (dB) Conversion Gain vs. LO Drive @ Vdd = +4V -16 20 FREQUENCY (GHz) MIXERS - CHIP CONVERSION GAIN (dB) Conversion Gain vs. Temperature @ LO = -5 dBm, Vdd= +4V -20 -30 -40 RF/IF LO/RF LO/IF 2LO/RF 2LO/IF -50 -20 -30 -40 RF/IF LO/RF LO/IF 2LO/RF 2LO/IF -50 -60 -60 16 17 18 19 20 21 22 FREQUENCY (GHz) 23 24 25 26 16 17 18 19 20 21 22 23 24 25 26 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 5 - 95 MICROWAVE CORPORATION HMC337 v01.0803 GaAs MMIC SUB-HARMONICALLY PUMPED MIXER, 17 - 25 GHz Input IP3 vs. LO Drive @ Vdd = +4V * Input IP3 vs. LO Drive @ Vdd = +3V * -7 dBm -5 dBm -3 dBm 16 12 8 4 0 5 -7 dBm -5 dBm -3 dBm 16 12 8 4 0 19 20 21 22 23 24 25 19 20 FREQUENCY (GHz) 22 23 25 THIRD ORDER INTERCEPT (dBm) 20 + 25 C + 85 C - 55 C 16 12 8 4 0 + 25 C + 85 C - 55 C 16 12 8 4 0 19 20 21 22 23 24 25 19 20 FREQUENCY (GHz) 21 22 23 24 25 FREQUENCY (GHz) Input IP2 vs. LO Drive @ Vdd = +4V * Input IP2 vs. LO Drive @ Vdd = +3V * 60 SECOND ORDER INTERCEPT (dBm) 60 50 40 30 20 -7 dBm -5 dBm -3 dBm 10 0 50 40 30 20 -7 dBm -5 dBm -3 dBm 10 0 19 20 21 22 23 24 25 FREQUENCY (GHz) 19 20 21 22 23 FREQUENCY (GHz) * Two-tone input power = -10 dBm each tone, 1 MHz spacing. 5 - 96 24 Input IP3 vs. Temperature @ LO = -5 dBm, Vdd = +3V * 20 SECOND ORDER INTERCEPT (dBm) 21 FREQUENCY (GHz) Input IP3 vs. Temperature @ LO = -5 dBm, Vdd = +4V * THIRD ORDER INTERCEPT (dBm) MIXERS - CHIP 20 THIRD ORDER INTERCEPT (dBm) THIRD ORDER INTERCEPT (dBm) 20 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 24 25 MICROWAVE CORPORATION HMC337 v01.0803 GaAs MMIC SUB-HARMONICALLY PUMPED MIXER, 17 - 25 GHz Input IP2 vs. Temperature @ LO = -5 dBm, Vdd = +4V * Input IP2 vs. Temperature @ LO = -5 dBm, Vdd = +3V * 60 SECOND ORDER INTERCEPT (dBm) 50 40 30 20 + 25 C + 85 C - 55 C 10 0 50 40 30 20 +25 C + 85 C - 55 C 10 0 19 20 21 22 23 24 25 19 20 21 FREQUENCY (GHz) 10 10 8 8 6 6 4 4 2 0 -2 -8 24 25 + 25 C + 85 C - 55 C 2 0 -2 -4 + 25 C + 85 C - 55 C -6 23 Input P1dB vs. Temperature @ LO = -5 dBm, Vdd = +3V P1dB (dBm) P1dB (dBm) Input P1dB vs. Temperature @ LO = -5 dBm, Vdd = +4V -4 22 FREQUENCY (GHz) -6 -8 -10 5 MIXERS - CHIP SECOND ORDER INTERCEPT (dBm) 60 -10 19 20 21 22 23 24 25 19 20 21 FREQUENCY (GHz) 22 23 24 25 FREQUENCY (GHz) RF & LO Return Loss @ LO = -5 dBm, Vdd = +4V IF Return Loss @ LO = -5 dBm, Vdd = +4V 0 0 RETURN LOSS (dB) RETURN LOSS (dB) -5 -5 -10 -15 LO RF -10 -15 -20 -25 -30 IF -35 -20 -40 0 5 10 15 20 25 30 35 40 FREQUENCY (GHz) 0 0.5 1 1.5 2 2.5 3 3.5 4 FREQUENCY (GHz) * Two-tone input power = -10 dBm each tone, 1 MHz spacing. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 5 - 97 MICROWAVE CORPORATION HMC337 v01.0803 GaAs MMIC SUB-HARMONICALLY PUMPED MIXER, 17 - 25 GHz Upconverter Performance Conversion Gain, LO = -5 dBm Vdd = +4V IF Bandwidth @ LO = -5 dBm Vdd=3V Vdd=4V -4 -8 -12 -16 -20 Vdd=3V Vdd=4V -4 -8 -12 -16 -20 0 0.5 1 1.5 2 2.5 3 3.5 4 16 17 18 19 FREQUENCY (GHz) 20 21 RF / IF Input (Vdd = +5V) +13 dBm LO Drive (Vdd = +5V) +13 dBm Vdd 5.5V Continuous Pdiss (Ta = 85 °C) (derate 2.64 mW/°C above 85 °C) 238 mW Storage Temperature -65 to +150 °C Operating Temperature -55 to +85 °C 23 24 25 26 MXN Spurious @ RF Port, Vdd = +4V MxN Spurious @ IF Port, Vdd = +4V nLO mRF ±5 ±4 ±3 nLO ±2 ±1 0 -3 -2 61 -1 59 31 0 52 23 1 2 3 88 49 48 71 95 RF = 22 GHz @ -10 dBm LO = 10.5 GHz @ -5 dBm All values in dBc below IF power level. Measured as downconverter. 5 - 98 22 FREQUENCY (GHz) Absolute Maximum Ratings MIXERS - CHIP 5 0 CONVERSION GAIN (dB) CONVERSION GAIN (dB) 0 34 -5 X 47 79 60 19 mIF ±5 ±4 ±3 ±2 ±1 -3 56 86 48 102 -2 65 25 59 53 -1 33 X 48 0 -10 16 -9 1 37 X 43 17 2 30 50 40 61 3 77 57 80 66 IF = 1 GHz @ -10 dBm LO = 10.5 GHz @ -5 dBm All values in dBc below RF power level. Measured as upconverter. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 0 MICROWAVE CORPORATION HMC337 v01.0803 GaAs MMIC SUB-HARMONICALLY PUMPED MIXER, 17 - 25 GHz Outline Drawing NOTES: 1. ALL DIMENSIONS IN INCHES (MILLIMETERS) 2. ALL TOLERANCES ARE ±0.001 (0.025) 3. DIE THICKNESS IS 0.004 (0.100) BACKSIDE IS GROUND 5. BOND PAD SPACING, CTR-CTR: 0.006 (0.150) 6. BACKSIDE METALLIZATION: GOLD 7. BOND PAD METALLIZATION: GOLD Pad Descriptions Pad Number Function Description 1 Vdd Power supply for the LO Amplifier. An external RF bypass capacitor of 100 - 330 pF is required. A MIM border capacitor is recommended. The bond length to the capacitor should be as short as possible. The ground side of the capacitor should be connected to the housing ground. 2 RF Port RF Port. This pad is AC coupled and matched to 50 Ohm from 15 - 30 GHz. 3 IF Port IF Port. This pad is DC coupled and should be DC blocked externally using a series capacitor whose value has been chosen to pass the necessary IF frequency range. Any applied DC voltage to this pin will result in die non-function and possible die failure. 4 LO Port LO Port. This pad is AC coupled and matched to 50 ohm from 8 - 12 GHz Interface Schematic For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 5 MIXERS - CHIP 4. BOND PADS ARE 0.004 (0.100) SQUARE 5 - 99 MICROWAVE CORPORATION HMC337 v01.0803 GaAs MMIC SUB-HARMONICALLY PUMPED MIXER, 17 - 25 GHz Assembly Diagram MIXERS - CHIP 5 Mounting & Bonding Techniques for Millimeterwave GaAs MMICs The die should be attached directly to the ground plane eutectically or with conductive epoxy (see HMC general Handling, Mounting, Bonding Note). 50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina thin film substrates are recommended for bringing RF to and from the chip (Figure 1). If 0.254mm (10 mil) thick alumina thin film substrates must be used, the die should be raised 0.150mm (6 mils) so that the surface of the die is coplanar with the surface of the substrate. One way to accomplish this is to attach the 0.102mm (4 mil) thick die to a 0.150mm (6 mil) thick molybdenum heat spreader (moly-tab) which is then attached to the ground plane (Figure 2). Microstrip substrates should be brought as close to the die as possible in order to minimize ribbon bond length. Typical die-to-substrate spacing is 0.076mm (3 mils). Gold ribbon of 0.075 mm (3 mil) width and minimal length <0.31 mm (<12 mils) is recommended to minimize inductance on RF, LO & IF ports. An RF bypass capacitor should be used on the Vdd input. A 100 pF single layer capacitor (mounted eutectically or by conductive epoxy) placed no further than 0.762mm (30 Mils) from the chip is recommended. 3 mil Ribbon Bond 3 mil Ribbon Bond 5 - 100 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION HMC337 v01.0803 GaAs MMIC SUB-HARMONICALLY PUMPED MIXER, 17 - 25 GHz GaAs Precautions MMIC SUB-HARMONICALLY PUMPED MIXER 17 - 25 GHz Handling Follow these precautions to avoid permanent damage. Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean the chip using liquid cleaning systems. Static Sensitivity: Follow ESD precautions to protect against > ± 250V ESD strikes. Transients: General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The surface of the chip has fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers. Mounting The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy. The mounting surface should be clean and flat. Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 °C and a tool temperature of 265 °C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 °C. DO NOT expose the chip to a temperature greater than 320 °C for more than 20 seconds. No more than 3 seconds of scrubbing should be required for attachment. 5 MIXERS - CHIP Suppress instrument and bias supply transients while bias is applied. Use shielded signal and bias cables to minimize inductive pick-up. Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule. Wire Bonding RF bonds made with 0.003” x 0.0005” ribbon are recommended. These bonds should be thermosonically bonded with a force of 40-60 grams. DC bonds of 0.001” (0.025 mm) diameter, thermosonically bonded, are recommended. Ball bonds should be made with a force of 40-50 grams and wedge bonds at 18-22 grams. All bonds should be made with a nominal stage temperature of 150 °C. A minimum amount of ultrasonic energy should be applied to achieve reliable bonds. All bonds should be as short as possible, less than 12 mils (0.31 mm). For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 5 - 101