BATTERY DRIVEN, FTP-608 Series 2” HIGH SPEED THERMAL PRINTER FTP-628MCL053/054 ■ OVERVIEW The FTP-628 MCL Series are battery driven high-speed ultracompact printers with a 2-inch paper width equivalent. Paper can be easily set using our unique platen release mechanism. The FTP-628 MCL Series can be used for a variety of applications, such as portable terminals, POS, ticket issuing terminals, label printers, banking terminals, and measurement and medical equipment. ■ HIGHLIGHTS • Ultra compact Height 15.5 mm, width 69.6 mm, depth 34.3 mm • High speed printing It can print at 60 mm/s (480 dotlines/s) maximum by using Fujitsu's unique head drive control. • High resolution printing / Kanji supported 8 dots/mm of resolution printing is possible. • Easy paper setting Our unique platen release mechanism allows a wide paper route even if the printer is ultra-compact, so paper can be easily inserted. Conventional auto loading is also available. • Two types of paper routes Front or bottom feed, depending on the paper route. • Easy mounting Wiring for the head, motor, sensor are housed within one flexible cable (053, 054) or in two cables (051, 052). The mechanism can be secured by one hook and two screws at two locations, making mounting easy. 1 FTP-628MCL053/054 ■ PART NUMBERS Part Number Printer mechanism FTP-628MCL053 (front paper insertion with head open detection switch and knob) FTP-628MCL054 (bottom paper insertion with head open detection switch) LSI for driving FTP-628CU301 (ANK only) Interface Board Parallel FTP-628DCL300 (Centronics) Serial FTP-628DSL305 Serial (RS232C) Interface cables Parallel FTP-628Y202 Serial FTP-628Y302 Power cable Head, motor FTP-628Y402 ■ SPECIFICATIONS Item Specifications Part number FTP-628MCL053/054 Printing method Thermal-line dot method Dot structure 384 dots/line Dot pitch (Horizontal) 0.125 mm (8 dots/mm)—Dot density Dot pitch (Vertical) 0.125 mm (8 dots/mm)—Line feed pitch Effective printing area 48 mm Number of columns ANK 32 columns/line (maximum 12 x 24 dot font) Paper width 58 mm+0 -1 Paper thickness 60 to 100 µ m (some paper in this range may not be used because of paper characteristics) Printing Speed Maximum 60mm/sec. (480 dot line/sec.) at 8.5V Character types Alphanumeric, katakana: International and special characters: JIS Kanji level 1, level 2, non-Kanji (supported only by FTP-628DSL228, DCL208): Character, dimensions (W×H), number of columns 159 types 195 types about 6800 types 12 × 24 dots, (1.54 × 3.0 mm), 32 columns: alphanumeric, katakana 24 × 24 dots, (3.0 × 3.0 mm), 16 columns: alphanumeric, katakana, Kanji 8 × 16 dots, (1.0 × 2.0 mm), 48 columns: alphanumeric, katakana 16 × 16 dots, (1.0 × 2.0 mm), 24 columns: alphanumeric, katakana, Kanji 2 FTP-628MCL053/054 ■ SPECIFICATIONS Item Interface Power supply Specification Conforms to RS232C / Centronics For print head 4.2 - 8.5 VDC average current, 0.87 (0.93) A peak value (print ratio: 12.5%, print speed: 50mm/sec. at 7.2V ) For motor 4.2 - 8.5 VDC, 1A maximum Note: 5.8 to 8.5 V is recommended for automatic paper loading For logic 5 VDC ± 5%, 0.1 A maximum Printer mechanism 72.3 x 34.3 x 15.5 mm (WxDxH) Interface board 69.3 x 52 x 15 mm Printer mechanism Approximately 47g (without knob) Interface board Approximately 20g Dimensions Weight Pulse resistance: 100 million pulses/dot (under our standard conditions) Abrasion resistance: paper traveling distance 50km (print ratio: 25% or less) Head life Operating temperature* Operating humidity Operating environment Storage temperature Detection function 0˚ C to +50˚ C 20 to 85% RH (no condensation) -20˚ C to +60˚ C (paper not included) Storage humidity 5 to 95% RH (no condensation) Head temperature detection Detected by thermistor Paper out/mark detection Detected by photo-interrupter Head up detection Detected by micro-switch Recommended thermal sensitive paper High Sensitive Paper TF50KS-E4 (Nippon Paper) Standard paper: TF60KS-E(Nippon Paper) FTP-020PU001 (58mm) PD105R (Oji Paper) FTP-020P0701 (58mm) Medium Life Paper TF60KS-F1 FTP-020P0102 (58mm) PD170R (Oji Paper) P220VBB-1 Mitsubishi Paper) Long Life Paper PD160R-N (Oji Paper) *+5˚C to +40˚C printing density assurance rance (-25 to 70˚C capability) 3 FTP-628MCL053/054 ■ DIMENSIONS 1. Printer mechanism FTP-628MCL054 FTP-628MCL053 Unit: mm Note: 1. Dimensions are nominal value (tolerance ±5 unless otherwise specified). 2. Platen unit (lever, platen, etc) moves by approximately 0.7mm toward paper insertion direction when platen is open. 2. Interface board Unit: mm 4 FTP-628MCL053/054 Connector (FPC) specification (1) Connector Mechanical unit side: FPC connector Remote side (housing site): 52030-3090 (made by Molex) (2) Pin assignment on the mechanical side No Signal I/O Contents — Cathode for photo interruptor 1 PHK 2 VSEN I paper sensor power 3 PHE O Emittor for photo interruptor 4 SW1 O Platen release switch 5 SW2 I Platen release switch 6 VH I 7 VH I 8 DI I Data in 9 CLK I Synchronous clock for communication 10 GND — 11 GND — 12 STB6 I 13 STB5 I 14 STB4 I 15 VDD I Logic power 16 TM O Thermally sensitive resistor input termnial 1 17 TM O Thermally sensitive resistor input termnial 2 18 STB3 I 19 STB2 I 20 STB1 I 21 GND — 22 GND — 23 LAT I Data latch 24 DO O Data out 25 VH I 26 VH I 27 MT/A I 28 MT/A I 29 MT/B I 30 MT/B I Head drive power Ground power supply for thermal head Thermal head energizing control signal Thermal head energizing control signal Ground power supply for thermal head Power supply for thermal head Stepping motor excitation signal 5 FTP-628MCL053/054 ■ FUNCTION OF INTERFACE BOARD Item Item 1. Test print function 8. Motor power saving function 2. Paper out detection 9. Mark detection function 3. Paper near end detection 10. MCU operation abnormality detection 4. Platen open detection 11. Power ON/OFF sequence protection 5. Thermal head temperature abnormality detection 12. Motor over-current protection 6. Blow-out fuse detection 13. Hardware timer 7. Head voltage abnormality detection Sensor (Photointerruptor) Platen unit Thermal head Motor FPC Connect terminal: surface side Connector No 30,29, .....................2,1 (FPC pin numbers) Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: [email protected] Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: [email protected] Web: www.fceu.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: [email protected] Web: www.fcai.fujitsu.com Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #04-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: [email protected] www.fcal.fujitsu.com © 2004 Fujitsu Components America, Inc. All company and product names are trademarks or registered trademarks of their respective owners. Rev. 11/15/2004. 6