MN101C35D Type MN101C35D ROM (×× 8-bit) 64 K RAM (×× 8-bit) 2K Package QFP100-P-1818B *Lead-free Minimum Instruction Execution Time 0.25 µs (at 2.7 V to 5.5 V, 8 MHz) 125 µs (at 2.2 V to 5.5 V, 32 kHz)* * The lower limit for operation guarantee for EPROM built-in type is 2.7 V. Interrupts • RESET • Watchdog • External 0 • External 1 • External 2 • External 3 • External 4 • Timer 0 • Timer 1 • Timer 2 • Timer 3 • Timer 4 • Timer 5 • Time base • Serial 0 • Serial 1 • Serial 2 • Automatic transfer finish • A/D conversion finish • Key scan Timer Counter Timer counter 0 : 8-bit × 1 (square-wave/8-bit PWM output, event count, generation of remote control carrier) Clock source ····················· 1/1, 1/4 of system clock frequency; 1/1 of OSC oscillation clock frequency; external clock input Interrupt source ················ coincidence with compare register 0 Timer counter 1 : 8-bit × 1 (square-wave output, event count, synchronous output event) Clock source ····················· 1/16, 1/64 of system clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ················ coincidence with compare register 1 Timer counter 0, 1 can be cascade-connected. Timer counter 2 : 8-bit × 1 (square-wave/8-bit PWM output, event count, synchronous output event) Clock source ····················· 1/1, 1/4 of system clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ················ coincidence with compare register 2 Timer counter 3 : 8-bit × 1 (square-wave output, event count, generation of remote control carrier, serial 0 baud rate timer) Clock source ····················· 1/4, 1/16 of system clock frequency; 1/1 of OSC oscillation clock frequency; external clock input Interrupt source ················ coincidence with compare register 3 Timer counter 2, 3 can be cascade-connected. Timer counter 4 : 16-bit × 1 (square-wave/16-bit PWM output, event count, synchronous output event, input capture) Clock source ····················· 1/4, 1/16 of system clock frequency; 1/1 of OSC oscillation clock frequency; external clock input Interrupt source ················ coincidence with compare register 4 Time base timer (one-minute count setting, independently operable 8-bit timer counter 5) Clock source ····················· 1/4 of system clock frequency; 1/1, 1/8192 of OSC oscillation clock frequency; 1/1, 1/8192 of XI oscillation clock frequency Interrupt source ················ coincidence with compare register 5; 1/8192 prescaler overflow Watchdog timer Interrupt source ················ 1/2097152 of system clock frequency Serial Interface Serial 0 : synchronous type/simple UART (half-duplex) × 1 Clock source ····················· 1/2, 1/4, 1/16 of system clock frequency; 1/2 of timer counter 3 frequency Serial 1 : synchronous type × 1 Clock source ····················· 1/2, 1/8, 1/64 of system clock frequency; 1/2 of timer counter 3 frequency Serial 2 : synchronous type/simple I2C × 1 Clock source ····················· 1/1, 1/2, 1/4 of system clock frequency; 1/2 of timer counter 0 frequency 1 MAD00024DEM MN101C35D I/O Pins I/O 36 • Common use : 28 • Specified pull-up resistor available • Input/output selectable (bit unit) High Voltage 53 • Output: 29 • I/O: 24 • P-ch open drain (breakdown voltage −30V): FL drive: 53 • Specified pull-down resistor mask option: 35 A/D Inputs 8-bit × 8-ch. (with S/H) FL (35 to 43) segments × (18 to 10) digits Special Ports Buzzer output, remote control carrier signal output Electrical Characteristics Supply current Limit Parameter Symbol Condition Unit min typ max IDD1 fosc = 8 MHz, VDD = 5 V 25 mA IDD2 fx = 32 kHz, VDD = 3 V 120 µA Supply current at HALT IDD3 fx = 32 kHz, VDD = 3 V 10 µA Supply current at STOP IDD4 VDD = 3 V 10 µA Operating supply current P95(→SEG18) P96(→SEG17) P97(→SEG16) P80(→SEG15) P81(→SEG14) P82(→SEG13) P83(→SEG12) P84(→SEG11) P85(→SEG10) P86(→SEG9) P87(→SEG8) P70(→SEG7/DGT0) P71(→SEG6/DGT1) P72(→SEG5/DGT2) P73(→SEG4/DGT3) P74(→SEG3/DGT4) P75(→SEG2/DGT5) P76(→SEG1/DGT6) P77(→SEG0/DGT7) P40(→DGT8) P41(→DGT9) P60(→DGT10) P61(→DGT11) P62(→DGT12) P63(→DGT13) 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 Pin Assignment P94(←SEG19) 76 50 P64(→DGT14) P93(←SEG20) 77 49 P65(→DGT15) P92(←SEG21) 78 48 P66(→DGT16) P91(←SEG22) 79 47 P67(→DGT17) P90(←SEG23) 80 46 P54 PC2(←SEG24) 81 45 P53 PC1(←SEG25) 82 44 P52 PC0(←SEG26) 83 43 P51 PB7(←SEG27) 84 42 P50 PB6(←SEG28) 85 41 P32(SBT2↔) PB5(←SEG29) 86 40 P31(SBI2←) 39 P30(SBO2→) 38 P25 37 P24(←IRQ4) PB4(←SEG30) 87 PB3(←SEG31) 88 PB2(←SEG32) 89 PB1(←SEG33) 90 36 P23(←IRQ3) MN101C35D 12 13 14 15 16 17 18 19 20 21 22 23 24 25 XI MMOD VREF- (AN0→)PA0 (AN1→)PA1 (AN2→)PA2 (AN3→)PA3 (AN4→)PA4 (AN5→)PA5 (AN6→)PA6 (AN7→)PA7 VREF+ P07 P27(NRST↔) XO 26 11 P10(RMOUT→,TM0IO↔) 100 VPP VSS 27 10 99 9 P11(TM1IO↔) PD0(←SEG42) OSC1 P12(TM2IO↔) 28 OSC2 29 98 8 97 PD1(←SEG41) VDD P13(TM3IO↔) PD2(←SEG40) 7 30 6 96 (SBT1↔)P05 P14(TM4IO↔) PD3(←SEG39) (DK,BUZZER↔)P06 P15 31 5 32 95 (SBI1→)P04 94 PD4(←SEG38) 4 P20(←IRQ0) PD5(←SEG37) 3 33 (SBT0↔)P02 93 (SBO1←)P03 P21(←SENS,IRQ1) PD6(←SEG36) 2 P22(←IRQ2) 34 1 35 92 (RXD,SBI0→)P01 91 (TXD,SBO0←)P00 PB0(←SEG34) PD7(←SEG35) QFP100-P-1818B *Lead-free See the next page for support tool. MAD00024DEM 2 Support Tool In-circuit Emulator PX-ICE101C / D + PX-PRB101C35-QFP100-P-1818B EPROM Built-in Type Type MN101CP35D ROM (× 8-bit) 64 K RAM (× 8-bit) 2K Minimum instruction execution time 0.25 µs (at 2.7 V to 5.5 V, 8 MHz) 125 µs (at 2.7 V to 5.5 V, 32 kHz) Package 3 QFP100-P-1818B *Lead-free MAD00024DEM MN101C35D MAD00024DEM 4 Request for your special attention and precautions in using the technical information and semiconductors described in this material (1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. It neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) We are not liable for the infringement of rights owned by a third party arising out of the use of the product or technologies as described in this material. (4) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: • Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. • Any applications other than the standard applications intended. (5) The products and product specifications described in this material are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (6) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage, and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) When using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd. 2002 JUL