CMOS LDO Regulator Series for Portable Equipments High-speed Load Response FULL CMOS LDO Regulators No.09020EAT01 BUTA2WNVX Series, BUTA2WHFV Series ●Description BU□□TA2WNVX /HFV series is high-performance FULL CMOS regulator with 200-mA output, which is mounted on microminiature package SSON004X1216 (1.2 mm 1.6 mm 0.6 mm) &HVSOF5(1.6mm X 1.6mm X0.6mm). It has excellent noise characteristics and load responsiveness characteristics despite its low circuit current consumption of 40 A. It is most appropriate for various applications such as power supplies for logic IC, RF, and camera modules. Microminiature package SSON004X1216 & HVSOF5 with built-in heatsink is adopted for the package, which contributes to the space-saving design of the set. ●Features 1) High-accuracy output voltage of 1% (25 mV on 1.5-V & 1.8-V products） 2) High ripple rejection: 70 dB (Typ., 1 kHz, VOUT1.8 V)) 3) Compatible with small ceramic capacitor (CIN=Co=1.0 F) 4) Low current consumption: 40 A 5) ON/OFF control of output voltage 6) With built-in overcurrent protection circuit and overheat protection circuit 7) With built-in output discharge circuit 8) Adopting microminiature power package SSON004X1216 ●Applications Battery-powered portable equipment, etc. Absolute maximum rating Parameter Maximum applied power voltage Power dissipation Maximum junction temperature Operational temperature range Storage temperature range Symbol VMAX Pd1 Pd2 TjMAX Topr Tstg Limits -0.3 ~ +6.5 220*1 (SSON004X1216) 410*2 (HVSOF5) +125 -40 ~ +85 -55 ~ +125 Unit V mW mW °C °C °C *1 When 1 PCB (70 mm 70 mm, thickness 1.6-mm glass epoxy) a standard ROHM board is implemented. Reduced to 2.2 mW/C when used at Ta=25C or higher. *2 When 1 PCB (70 mm 70 mm, thickness 1.6-mm glass epoxy) a standard ROHM board is implemented. Reduced to 4.1 mW/C when used at Ta=25C or higher. Recommended operating range (Do not exceed Pd.） Parameter Symbol Limits Input power supply voltage VIN 2.5 ~ 5.5 Maximum output current IMAX 200 Recommended operating conditions Parameter Symbol Min. Typ. Max. Input capacitor CIN 0.5*3 1.0 － Output capacitor CO 0.5*3 1.0 － *3 Set the capacity value of the capacitor so that it does not fall below DC device characteristics, and change with time into consideration. www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 1/27 Unit V mA Unit Conditions μF A ceramic capacitor is recommended. μF A ceramic capacitor is recommended. the minimum value, taking temperature characteristics, 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series Block diagram, recommended circuit diagram, and pin configuration diagram BH□□TA2WNVX VIN VIN 4/3 VREF Cin VOUT VOUT 1 1/4 OCP 2 Co GND VSTBY STBY STBY 3/1 Discharge Recommended ceramic capacitor for Cin & Co Murata Manufacturing Co., Ltd. GRM188B11A105KA61D Fig.1 Recommended circuit diagram BU□□TA2WNVX(SSON004X1216) 4 3 1 2 PIN No. Symbol Function 1 VOUT Voltage output 2 GND Grounding 3 STBY ON/OFF control of output voltage (High: ON, Low: OFF) 4 VIN Power input BU□□TA2WHFV(HVSOF5) 5 1 4 2 PIN No. Symbol Function 1 STBY ON/OFF control of output voltage (High:ON, Low:OFF) 2 GND Grounding 3 VIN Power input 4 VOUT Voltage output 5 N.C. No Connect 3 www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 2/27 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series ●Electrical characteristics(Ta=25C, VIN=VOUT+1.0 V (VIN=3.5 V on VOUT=1.8-V and1.5-V products), STBY=1.5 V, CIN=1.0 F, CO=1.0 F, unless otherwise specified) Parameter Symbol Min. VOUT×0.99 Typ. Unit Conditions V Output voltage VOUT Circuit current IIN - 40 95 ISTBY - - 1 μA - dB Circuit current (at STBY) VOUT-25 mV VOUT Max. VOUT×1.01 IOUT=10 μA，VOUT<2.5 V VOUT+25 mV μA IOUT=0mA 70 Ripple rejection RR 55 65 Input/Output voltage difference Line regulation IOUT=10 μA，VOUT≥2.5 V STBY=0 V VRR=-20 dBv, fRR=1 kHz, IOUT=10 mA 1.5 V≤VOUT≤1.8 V VRR=-20 dBv,fRR=1 kHz, IOUT=10 mA 2.5 V≤VOUT - 400 800 mV 2.5 V≤VOUT≤2.6 V (VIN=0.98*VOUT, IOUT=200 mA) - 360 720 mV 2.7 V≤VOUT≤2.85 V (VIN=0.98*VOUT, IOUT=200 mA) - 330 660 mV 2.9 V≤VOUT≤3.1 V (VIN=0.98*VOUT,IOUT=200 mA) - 300 600 mV 3.2 V≤VOUT≤3.4 V (VIN=0.98*VOUT, IOUT=200 mA) VDL - 2 20 mV VDLO - 10 80 mV VIN=VOUT+1.0 V to 5.5 V, IOUT=10 μA IOUT=0.01 mA to 100 mA VSAT Load regulation Overcurrent protection detection current Output short-circuit current ILMAX 250 400 700 mA Vo=VOUT*0.8 ISHORT 20 70 150 mA Vo=0 V Output discharge resistance RDSC 20 40 80 Ω Standby pull-down resistance RSTB 500 1000 2000 kΩ Standby control ON VSTBH 1.5 - 5.5 V OFF VSTBL -0.3 - 0.3 V VIN=4.0 V, STBY=0 V * This product does not have radiation-proof design. www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 3/27 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series Lineup ■ 200 mA BU□□TA2WNVX / HFV series Product Name 1.5 1.8 2.5 2.6 BU□□TA2WNVX BU□□TA2WHFV 2.7 2.8 2.85 ○ ○ ○ ○ ○ ○ ○ 2.9 3.0 3.1 3.2 3.3 3.4 ○ ○ ○ ○ ○ ○ - Package SSON004X1216 HVSOF5 Model name: BU□□TA2WNVX / HFV a Symbol Contents Output voltage (V) □□ a Specification of output voltage Output □□ voltage (V) Output voltage (V) □□ 15 1.5 V(Typ.) 28 2.8 V(Typ.) 32 3.2 V(Typ.) 18 1.8 V(Typ.) 2J 2.85 V(Typ.) 33 3.3 V(Typ.) 25 2.5 V(Typ.) 29 2.9 V(Typ.) 34 3.4 V(Typ.) 26 2.5 V(Typ.) 30 3.0 V(Typ.) - - 27 2.7 V(Typ.) 31 3.1 V(Typ.) - - Input/Output terminal equivalent circuit schematic 1pin (VOUT) 2pin (GND) 3pin (STBY) VIN 4pin (VIN) VIN VOUT STBY Fig.２ About input/output capacitor Capacity value of ceramic capacitor - DC bias characteristics (Example) It is recommended to place a capacitor as close as possible to the pins between the input terminal and GND or between the output terminal and GND. The capacitor between the input terminal and GND becomes valid when source impedance increases or when wiring is long. The larger the capacity of the output capacitor between the output terminal and GND is, the better the stability and characteristics in output load fluctuation become. However, please check the status of actual implementation. Ceramic capacitors generally have variation, temperature characteristics, and direct current bias characteristics and the capacity value also decreases with time depending on the usage conditions. It is recommended to select a ceramic capacitor upon inquiring about detailed data of the related manufacturer. 10-V withstand voltage B1characteristics GRM188B11A105KA61D 10 0 -10 Capacitance Change [%] Input/Output equivalent circuit 10-V withstand voltage B characteristics -20 6.3-V withstand voltage B characteristics -30 10-V withstand voltage F characteristics -40 -50 -60 4-V withstand voltage X6S characteristics 10-V withstand voltage F characteristics -70 -80 -90 -100 0 0.5 1 1.5 2 2.5 3 3.5 4 DC Bias Voltage [V] About the equivalent series resistance (ESR) of a ceramic capacitor 100 ESR [Ω] Capacitors generally have ESR (equivalent series resistance) and it operates stably in the ESR-IOUT area shown on the right. Since ceramic capacitors, tantalum capacitors, electrolytic capacitors, etc. generally have different ESR, please check the ESR of the capacitor to be used and use it within the stability area range shown in the right graph for evaluation of the actual application. Fig.3 Capacity – bias characteristics Unstable area 10 Stability area 1 0.1 0.01 0 50 100 150 200 IOUT [mA] Fig.4 Stability area characteristics (Example) www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 4/27 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series BU15TA2WNVX / HFV Reference data (Ta=25ºC unless otherwise specified.) 100 1.55 1.54 1.5 1.2 IO=0uA IO=100uA IO=50mA IO=200mA 0.9 0.6 Temp=25°C VIN = STBY 0.3 IO=0uA IO=100uA IO=50mA IO=200mA 1.53 1.52 1.51 1.50 1.49 1.48 1.47 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 1.25 1.35 1.45 1.55 1.65 1.75 1.85 1.95 Vin Voltage (V) 0 2.05 2.15 2.25 IO=0uA VIN = STBY 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 Vin Voltage (V) Fig. 7 Circuit Current IGND 120 10 110 100 80 60 Temp=-40°C Temp=25°C Temp=85°C 40 20 IO=200mA VIN = STBY 8 Temp=85°C Temp=85°C Gnd Current (uA) STBY Current (uA) 120 Temp=25°C 6 Temp=-40°C 4 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 0 5.5 Output Voltage (V) Temp=25°C Temp=-40°C 1.51 1.50 1.49 1.48 VIN = 3.5V STBY = 1.5V 0.05 0.1 0.15 VIN=3.5V 1.25 1.00 VIN=2.5V 0.75 0.50 Temp=25°C STBY = 1.5V 0.10 Fig. 11 Load Regulation 0.20 0.30 0.40 0.50 1.52 1.51 1.50 1.49 VIN=3.5V STBY=1.5V Io=0.1mA 1.45 40.00 30.00 20.00 VIN=3.5V STBY=1.5V Io=0mA 10.00 0.00 10 35 0.5 60 85 Temp (°C) Fig. 14 VOUT vs. Temp www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. -40 -15 10 35 60 Temp (°C) Fig. 15 IGND vs. Temp 5/27 1 1.5 Fig. 13 STBY Threshold Gnd Current (uA) Input Current (uA) 1.53 -15 Temp=85°C Temp=25°C Temp=-40°C 0.50 STBY Voltage (V) 50.00 -40 0.75 0 1.54 1.46 1.00 0.25 0.60 Fig. 12 OCP Threshold 1.55 1.47 1.25 Output Current (A) Output Current (A) 1.48 1.50 0.00 0.00 0.2 0.2 1.75 1.50 0.00 0 0.15 2.00 0.25 1.45 0.1 Fig. 10 IOUT - IGND VIN=5.5V 1.75 1.46 0.05 Output Current (A) 2.00 1.54 Temp=85°C VIN = 3.5V STBY = 1.5V Fig. 9 STBY Input Current 1.55 1.47 Temp=-40°C 60 STBY Voltage (V) Fig. 8 Circuit Current IGND 1.52 70 40 Vin Voltage (V) 1.53 80 50 0 0.5 Temp=25°C 90 VIN = STBY 0 0 100 2 Output Voltage (V) Gnd Current (uA) Temp=-40°C Temp=25°C Temp=85°C Fig. 6 Line Regulation 140 Output Voltage (V) 40 Vin Voltage (V) Fig. 5 Output Voltage Output Voltage (V) 60 0 1.45 0 80 20 Temp=25°C VIN = STBY 1.46 0.0 Gnd Current (uA) Output Voltage (V) Output Voltage (V) 1.8 85 1.000 0.900 0.800 0.700 0.600 0.500 0.400 0.300 0.200 0.100 0.000 -0.100 -40 VIN=3.5V STBY=0V -15 10 35 60 85 Temp (°C) Fig. 16 IGND vs. Temp (STBY) 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series BU15TA2WNVX /HFV 80 80 0.7 f= 0 .1 kHz 70 Ripple Rejection [dB] Ripple Re je c tion (dB ) 70 (Ta=25ºC unless otherwise specified.) O u tpu t N o is e D e n s ity [μ V / √ H z ] Reference data 60 50 40 30 Vin= 3.5V Io=10mA Ta = 25℃ 20 10 f= 1 kHz 60 f= 1 0 kHz 50 40 30 f= 1 0 0 kHz Co=1.0μF Cin=none Iout=10mA temp=25℃ 20 10 0 0 2.5 0.1 1 10 100 1000 Frequency (kHz) Fig. 17 Ripple Rejection vs. Freq. 3.5 4.5 Input Voltage VIN[V] Fig. 18 Ripple Rejection vs. VIN (Iout=10 mA) 5.5 Co=1.0μF Cin=1.0μF Iout=10mA temp=25℃ 0.6 0.5 0.4 0.3 0.2 0.1 0 0.1 1 10 Frequency f [kHz] Fig. 19 Output Noise Spectral Density vs. Freq. Fig. 20 Load Response Fig. 21 Load Response Fig. 22 Load Response Fig. 23 Load Response Fig. 24 Load Response Current Pulse=10 kHz www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 100 Fig. 25 Load Response Current Pulse=10 kHz 6/27 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series Reference data BU15TA2WNVX / HFV (Ta=25ºC unless otherwise specified.) Fig. 26 Load Response Current Pulse=100 kHz Fig. 28 Startup Time Iout = 0 mA Fig. 31 Startup Time (STBY=VIN) Iout = 200mA www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. Fig. 27 Load Response Current Pulse=100 kHz Fig. 29 Startup Time Iout = 200 mA Fig. 32 Discharge Time Iout = 0 mA 7/27 Fig. 30 Startup Time (STBY=VIN) Iout = 0 mA Fig. 33 VIN Response Iout = 10 mA 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series BU18TA2WNVX / HFV ●Reference data 3.5 100 1.85 1.84 2.5 2.0 1.5 IO=0uA IO=100uA IO=50mA IO=200mA 1.0 0.5 Temp=25°C VIN = STBY IO=0uA IO=100uA IO=50mA IO=200mA 1.83 1.82 1.81 1.80 1.79 1.78 1.77 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 1.85 1.95 2.05 2.15 2.25 0 2.35 0.5 1 1.5 Fig. 35 Line Regulation 2 2.5 3 3.5 4 4.5 5 5.5 Fig. 36 Circuit Current IGND 120 10 140 IO=0uA VIN = STBY Vin Voltage (V) Vin Voltage (V) Fig. 34 Output Voltage 110 100 80 60 Temp=-40°C Temp=25°C Temp=85°C 40 IO=200mA VIN = STBY 20 Temp=85°C Temp=85°C 8 Gnd Current (uA) STBY Current (uA) 120 Temp=25°C 6 Temp=-40°C 4 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 0 5.5 0.5 1 1.5 Output Voltage (V) Temp=25°C Temp=-40°C 1.81 1.80 1.79 1.78 VIN = 3.5V STBY = 1.5V 1.76 2 2.5 3 3.5 4 4.5 5 3.50 3.00 VIN=5.5V 2.00 VIN=3.5V 1.50 1.00 VIN=2.5V Temp=25°C STBY = 1.5V 0.1 0.15 0.2 0.10 Output Current (A) Fig. 40 Load Regulation 0.20 0.30 0.40 0.50 0.60 Fig. 41 OCP Threshold 1.81 1.80 1.79 VIN=3.5V STBY=1.5V Io=0.1mA 40.00 30.00 20.00 VIN=3.5V STBY=1.5V Io=0mA 10.00 0.00 1.75 -40 -15 10 35 60 85 Temp (°C) Fig. 43 VOUT vs Temp www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. -40 -15 10 35 60 Temp (°C) Fig. 44 IGND vs Temp 8/27 0.5 1 1.5 Fig. 42 STBY Threshold G nd Current (uA) Input Current (uA) 1.82 1.76 Temp=85°C Temp=25°C Temp=-40°C 1.00 STBY Voltage (V) 1.84 1.77 1.50 0 50.00 1.78 2.00 Output Current (A) 1.83 0.2 0.00 0.00 1.85 0.15 2.50 0.50 0.00 0.05 0.1 Fig. 39 IOUT - IGND 3.00 2.50 0.05 Output Current (A) 3.50 0.50 1.75 0 VIN = 3.5V STBY = 1.5V 0 5.5 Fig. 38 STBY Input Current 1.84 Temp=85°C Temp=-40°C 60 STBY Voltage (V) 1.85 1.77 70 40 Fig. 37 Circuit Current IGND 1.82 80 50 Vin Voltage (V) 1.83 Temp=25°C 90 VIN = STBY Output Voltage (V) 0 100 2 0 0 Output Voltage (V) Temp=-40°C Temp=25°C Temp=85°C 20 0 1.75 Vin Voltage (V) Gnd Current (uA) 40 1.75 0 Output Voltage (V) 60 Temp=25°C VIN = STBY 1.76 0.0 80 Gnd Current (uA) Output Voltage (V) 3.0 Output Voltage (V) (Unless otherwise specified, Ta=25℃) 85 1.000 0.900 0.800 0.700 0.600 0.500 0.400 0.300 0.200 0.100 0.000 -0.100 -40 VIN=3.5V STBY=0V -15 10 35 60 85 Temp (°C) Fig. 45 IGND vs Temp (STBY) 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series BU18TA2WNVX / HFV 80 70 70 60 50 40 30 Vin= 3.5V Io=10mA Ta = 25℃ 20 10 (Unless otherwise specified, Ta=25℃) 0.7 f= 0 .1 kHz O u tpu t N oise D e n sity [μ V / √ H z] 80 Ripple Rejection [dB] R ipple R ejection (dB) ●Reference data f= 1 kHz 60 f= 1 0 kHz 50 40 f= 1 0 0 kHz 30 Co=1.0μF Cin=none Iout=10mA temp=25℃ 20 10 0 0 0.1 1 10 100 1000 Frequency (kHz) Fig. 46 Ripple Rejection VS Freq. 2.5 3.5 4.5 5.5 Co=1.0μF Cin=1.0μF Iout=10mA temp=25℃ 0.6 0.5 0.4 0.3 0.2 0.1 0 0.1 1 Input Voltage VIN[V] Fig. 47 Ripple Rejection VS VIN Fig. 49 Load Response 10 Frequency f [kHz] 100 Fig. 48 Output Noise Spectrl Density VS Freq. Fig. 50 Load Response Fig. 51 Load Response Fig. 52 Load Response ⇔ Fig. 53 Load Response Current Pulse=10kHz www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. Fig. 54 Load Response Current Pulse=10kHz 9/27 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series ●Reference data BU18TA2WNVX / HFV (Unless otherwise specified, Ta=25℃) ⇔ Fig. 55 Load Response Current Pulse=100kHz Fig. 57 Start Up Time Iout = 0mA Fig. 60 Start Up Time(STBY=VIN) Iout = 200mA www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. Fig. 56 Load Response Current Pulse=100kHz Fig. 58 Start Up Time Iout = 200mA Fig. 61 Discharge Time Iout = 0mA 10/27 Fig. 59 Start Up Time (STBY=VIN) Iout = 0mA Fig. 62 VIN Response Iout = 10mA 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series BU25TA2WNVX / HFV ●Reference data 3.5 100 2.55 2.54 2.5 2.0 IO=0uA IO=100uA IO=50mA IO=200mA 1.5 1.0 0.5 Temp.=25°C VIN=STBY IO=0uA IO=100uA IO=50mA IO=200mA 2.53 2.52 2.51 2.50 2.49 2.48 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 40 Temp.=-40°C Temp.=25°C Temp.=85°C 2.4 2.5 2.6 2.7 2.8 2.9 0 3 0.5 1 1.5 2.5 0.35 Temp.=25°C 0.30 0.25 Temp.=-40°C 0.20 0.15 0.10 VIN=0.98*VOUT STBY=1.5V 0.05 Temp.=85°C 8 Gnd Current (uA) STBY Current (uA) 110 Temp.=85°C Temp.=25°C 6 Temp.=-40°C 4 0.05 0.1 0.15 4 4.5 5 5.5 Temp.=-40°C 100 Temp.=25°C 90 80 Temp.=85°C 70 60 2 50 0 0.00 0 3.5 120 10 0.45 0.40 3 Fig. 65 Circuit Current IGND Fig. 64 Line Regulation 0.50 2 Vin Voltage (V) Vin Voltage (V) Fig. 63 Output Voltage IO=0uA VIN=STBY 0 Vin Voltage (V) Dropout Voltage (V) 60 Temp.=25°C VIN=STBY 2.45 0 80 20 2.47 2.46 0.0 Gnd Current (uA) Output Voltage (V) 3.0 Output Voltage (V) (Unless otherwise specified, Ta=25℃) 40 0 0.2 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 0 5.5 0.05 STBY Voltage (V) Output Current (A) Fig. 66 Dropout Voltage Fig. 67 STBY Input Current 2.55 0.1 0.15 0.2 Output Current (A) Fig. 68 IOUT - IGND 3.00 3.50 Temp.=25°C 2.52 Temp.=85°C 2.51 2.50 2.49 2.48 2.47 VIN=3.5V STBY=1.5V Temp.=-40°C 2.46 3.00 VIN=5.5V VIN=3.5V 2.00 VIN=3.0V 1.50 1.00 Temp.=25°C 0.50 0.00 0 0.05 0.1 0.15 0.2 1.50 Temp.=85°C Temp.=25°C Temp.=-40°C 1.00 0.1 0.2 0.3 0.4 0.5 0.6 0 0.5 Output Current (A) Fig. 69 Load Regulation 1.5 Fig. 71 STBY Threshold 1.000 50.00 VIN=3.5V STBY=1.5V Io=0.1mA 1 STBY Voltage (V) Fig. 70 OCP Threshold 2.55 0.900 2.52 2.51 2.50 2.49 2.48 2.47 0.800 40.00 Gnd Current (uA) Gnd Current (uA) 2.53 2.00 0.00 0 Output Current (A) 2.54 2.50 0.50 STBY=1.5V 2.45 Output Voltage (V) Output Voltage (V) 2.53 2.50 Output Voltage (V) Output Voltage (V) 2.54 VIN=3.5V STBY=1.5V Io=0mA 30.00 20.00 10.00 0.700 0.600 0.500 0.400 0.300 0.200 VIN=3.5V STBY=0V 0.100 2.46 0.000 2.45 -0.100 0.00 -40 -15 10 35 60 85 Temp. (°C) Fig. 72 VOUT vs Temp www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. -40 -15 10 35 Temp. (°C) Fig. 73 IGND vs Temp 11/27 60 85 -40 -15 10 35 60 85 Temp. (°C) Fig. 74 IGND vs Temp (STBY) 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series ●Reference data BU25TA2WNVX / HFV (Unless otherwise specified, Ta=25℃) 80 80 1.2 O utput N oise D ensity [μ V /√ H z] f= 0 .1 kHz 70 60 Ripple Rejection [dB] Ripple Rejection (dB ) 70 50 40 30 20 Vin= 3.5V Io=10mA Ta = 25℃ 10 60 f= 1 kHz 50 f= 1 0 kHz 40 f= 1 0 0 kHz 30 Co=1.0μF Cin=none Iout=10mA temp=25℃ 20 10 0 0 0.1 1 10 100 1000 Frequency (kHz) 2.5 3.5 4.5 5.5 Co=1.0μF Cin=1.0μF Iout=10mA temp=25℃ 1 0.8 0.6 0.4 0.2 0 0.1 I OU T=0m A →100m A 10 Frequency f [kHz] I OU T=100m A →0m A Fig. 79 Load Response Fig. 78 Load Response Fig. 80 Load Response Fig. 81 Load Response ⇔ ⇔ Fig. 82 Load Response Current Pulse=10kHz Fig. 83 Load Response Current Pulse=10kHz www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 100 Fig. 77 Output Noise Spectrl Density VS Freq. Fig. 76 Ripple Rejection VS VIN Fig. 75 Ripple Rejection VS Freq. 1 Input Voltage VIN[V] 12/27 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series ●Reference data BU25TA2WNVX / HFV (Unless otherwise specified, Ta=25℃) ⇔ ⇔ Fig. 84 Load Response Current Pulse=100kHz Fig. 86 Start Up Time Iout = 0mA Fig. 89 Start Up Time(STBY=VIN) Iout = 200mA www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. Fig. 85 Load Response Current Pulse=100kHz Fig. 87 Start Up Time Iout = 200mA Fig. 90 Discharge Time Iout = 0mA 13/27 Fig. 88 Start Up Time (STBY=VIN) Iout = 0mA Fig. 91 VIN Response Iout = 10mA 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series BU28TA2WNVX / HFV ●Reference data 3.5 100 2.85 IO=0uA 2.84 2.5 2.0 IO=0uA IO=100uA IO=50mA IO=200mA 1.5 1.0 Temp.=25°C VIN = STBY 0.5 IO=0uA IO=100uA IO=50mA IO=200mA 2.83 2.82 2.81 2.80 2.79 2.78 2.77 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 Temp.=-40°C Temp.=25°C Temp.=85°C VIN = STBY 0 2.7 2.8 2.9 Vin Voltage (V) 3 3.1 3.2 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 Vin Voltage (V) Fig. 92 Output Voltage Vin Voltage (V) Fig. 94 Circuit Current IGND Fig. 93 Line Regulation 10 0.40 120 0.35 110 Temp.=85°C 0.25 Temp.=25°C 0.20 Temp.=-40°C 0.15 0.10 8 Temp.=85°C Temp.=25°C 6 Temp.=-40°C 4 Temp.=85°C 100 90 Temp.=25°C 80 70 Temp.=-40°C 60 2 VIN=0.98 x VOUT 0.05 Gnd Current (uA) 0.30 STBY Current (uA) VIN = 3.8V 50 VIN = STBY STBY = 1.5V STBY = 1.5V 40 0 0.00 0 0.05 0.1 0.15 0 0.2 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 0 5.5 0.05 Fig. 95 Dropout Voltage Fig. 96 STBY Input Current 0.15 0.2 Fig. 97 IOUT - IGND 3.50 3.50 2.85 0.1 Output Currnt (A) STBY Voltage (V) Output Current (A) VIN=3.8V VIN = 3.8V 2.83 STBY = 1.5V 3.00 3.00 Output Voltage (V) 2.84 2.82 Temp.=-40°C 2.81 2.80 2.79 2.78 2.77 Temp.=85°C Temp.=25°C Output Voltage (V) Dropout Voltage (V) 40 2.75 0 Output Voltage (V) 60 20 Temp.=25°C 2.76 0.0 VIN = STBY 80 Gnd Current (uA) Output Voltage (V) 3.0 Output Voltage (V) (Unless otherwise specified, Ta=25℃) VIN=3.8V 2.50 VIN=5.5V 2.00 VIN=3.3V 1.50 1.00 Temp=25°C STBY = 1.5V 0.50 2.76 2.50 2.00 1.50 Temp.=85°C Temp.=25°C Temp.=-40°C 1.00 0.50 0.00 2.75 0 0.05 0.1 0.15 0 0.2 0.1 0.2 0.3 0.4 0.5 0.6 0.00 Output Current (A) Output Currnt (A) 0 0.5 1 1.5 STBY Voltage (V) Fig. 98 Load Regulation Fig. 99 OCP Threshold Fig. 100 STBY Threshold 50.00 2.85 1.000 0.900 2.82 2.81 2.80 2.79 2.78 VIN=3.8V STBY=1.5V Io=0.1mA 2.77 2.76 0.800 40.00 Gnd Current (uA) 2.83 Gnd Current (uA) Output Voltage (V) 2.84 30.00 20.00 VIN=3.8V STBY=1.5V Io=0mA 10.00 -40 -15 10 35 60 85 Temp. (°C) Fig. 101 VOUT vs Temp www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 0.600 0.500 0.400 0.300 VIN=3.8V STBY=0V 0.200 0.100 0.000 0.00 2.75 0.700 -0.100 -40 -15 10 35 Temp. (°C) Fig. 102 IGND vs Temp 14/27 60 85 -40 -15 10 35 60 85 Temp. (°C) Fig. 103 IGND vs Temp (STBY) 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series BU28TA2WNVX / HFV 80 80 1.6 f= 0 .1 kHz 70 60 Ripple Rejection [dB] Ripple Rejection (dB ) 70 (Unless otherwise specified, Ta=25℃) 50 40 30 20 Vin= 3.8V Io=10mA Ta = 25℃ 10 1 50 f= 1 0 kH z 40 f= 1 0 0 kH z 30 Co=1.0μF Cin=none Iout=10mA temp=25℃ 20 10 10 100 1000 Frequency (kHz) 2.8 3.8 1.2 1 0.8 0.6 0.4 0.2 0 4.8 0.1 100 Fig. 106 Output Noise Spectrl Density VS Freq. Fig. 110 Load Response Fig.109 Load Response ⇔ ⇔ Fig. 112 Load Response Current Pulse=10kHz Fig. 111 Load Response Current Pulse=10kHz www.rohm.com 10 Frequency f [kHz] Fig. 108 Load Response Fig. 107 Load Response © 2009 ROHM Co., Ltd. All rights reserved. 1 Input Voltage VIN[V] Fig. 105 Ripple Rejection VS VIN Fig. 104 Ripple Rejection VS Freq. Co=1.0μF Cin=1.0μF Iout=10mA temp=25℃ 1.4 0 0 0.1 60 f= 1 kH z O utput N oise D ensity [μ V /√ H z] ●Reference data 15/27 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series ●Reference data BU28TA2WNVX / HFV (Unless otherwise specified, Ta=25℃) ⇔ ⇔ Fig. 113 Load Response Current Pulse=100kHz Fig. 115 Start Up Time Iout = 0mA Fig. 118 Start Up Time(STBY=VIN) Iout = 200mA www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. Fig. 114 Load Response Current Pulse=100kHz Fig. 116 Start Up Time Iout = 200mA Fig. 119 Discharge Time Iout = 0mA 16/27 Fig. 117 Start Up Time (STBY=VIN) Iout = 0mA Fig.120 VIN Response Iout = 10mA 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series BU30TA2WNVX / HFV 3.05 3.0 3.04 2.5 2.0 IO=0uA IO=100uA IO=50mA IO=200mA 1.5 1.0 Temp.=25°C 0.5 (Unless otherwise specified, Ta=25℃) 100 IO=0uA IO=100uA IO=50mA IO=200mA 3.03 3.02 3.01 3.00 2.99 2.98 2.97 2.95 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 3 3.1 3.2 3.3 3.4 Temp.=-40°C Temp.=25°C Temp.=85°C 3.5 0 0.5 1 1.5 2 2.5 110 Temp.=25°C 0.20 Temp.=-40°C 0.15 0.10 VIN=0.98*VOUT STBY=1.5V 0.05 Temp.=85°C 8 Gnd Current (uA) STBY Current (uA) 0.25 Temp.=25°C 6 Temp.=-40°C 4 0.05 0.1 0.15 0.2 0.5 1 1.5 Output Current (A) 5.5 Temp.=25°C 100 Temp.=85°C 90 80 Temp=-40°C 70 60 2 2.5 3 3.5 4 4.5 5 5.5 0 0.05 STBY Voltage (V) 0.1 0.15 0.2 Output Current (A) Fig. 125 STBY Input Current Fig. 126 IOUT - IGND 3.50 3.05 5 40 0 Fig. 124 Dropout Voltage 4.5 50 0 0 VIN=STBY 4 2 VIN=STBY 0.00 3.5 120 10 Temp.=85°C 3 Fig. 123 Circuit Current IGND 0.35 0.30 IO=0uA Vin Voltage (V) Fig. 122 Line Regulation 0.40 3.50 VIN=4.0V 3.04 3.00 Output Voltage (V) Temp.=25°C 3.02 3.01 3.00 2.99 2.98 2.97 Temp.=-40°C VIN=4.0V STBY=1.5V 2.96 3.00 VIN=5.5V VIN=4.0V 2.50 VIN=3.5V 2.00 1.50 1.00 Temp.=25°C STBY=1.5V 0.50 Temp.=85°C Output Voltage (V) 3.03 0 0.05 0.1 0.15 0.1 Fig. 127 Load Regulation 0.2 0.3 0.4 0.5 0.6 0 1 1.5 Fig. 129 STBY Threshold 1.000 Input Current (µA) 0.900 3.02 3.01 3.00 2.99 2.98 2.97 0.800 40.00 30.00 20.00 VIN=4.0V STBY=1.5V Io=0mA 10.00 2.96 2.95 10 35 60 85 Temp. (°C) Fig. 130 VOUT vs Temp www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 0.700 0.600 0.500 0.400 VIN=4.0V STBY=0V Io=0mA 0.300 0.200 0.100 0.000 -0.100 0.00 -15 0.5 STBY Voltage (V) 50.00 VIN=4.0V STBY=1.5V Io=0.1mA -40 Temp.=85°C Temp.=25°C Temp.=-40°C 1.00 Fig.128 OCP Threshold 3.05 3.03 1.50 Output Current (A) Output Current (A) 3.04 2.00 0.00 0 0.2 2.50 0.50 0.00 2.95 Input Current (µA) Dropout Voltage (V) 40 Vin Voltage (V) Fig. 121 Output Voltage Output Voltage (V) 60 0 2.9 Vin Voltage (V) Output Voltage (V) 80 20 Temp.=25°C VIN=STBY 2.96 VIN=STBY 0.0 Gnd Current (uA) 3.5 Output Voltage (V) Output Voltage (V) ●Reference data -40 -15 10 35 Temp. (°C) Fig. 131 IGND vs Temp 17/27 60 85 -40 -15 10 35 60 85 Temp. (°C) Fig. 132 IGND vs Temp (STBY) 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series ●Reference data BU30TA2WNVX / HFV (Unless otherwise specified, Ta=25℃) 80 80 1.6 O u tpu t N o ise D e n sity [μ V / √ H z] f= 0 .1 kHz 70 60 Ripple Rejection [dB] Ripple Re je c tio n (dB ) 70 50 40 30 Vin= 4.0V Io=10mA Ta = 25℃ 20 10 60 f= 1 kH z 50 f= 1 0 kHz 40 30 f= 1 0 0 kHz Co=1.0μF Cin=none Iout=10mA temp=25℃ 20 10 0 3 0 0.1 1 10 100 1000 Frequency (kHz) Fig. 133 Ripple Rejection VS Freq. 4 Co=1.0μF Cin=1.0μF Iout=10mA temp=25℃ 1.4 1.2 1 0.8 0.6 0.4 0.2 0 5 0.1 1 Input Voltage VIN[V] Fig. 134 Ripple Rejection VS VIN Fig. 136 Load Response Fig. 137 Load Response Fig. 139 Load Response Fig. 140 Load Response Current Pulse=10kHz Fig. 141 Load Response Current Pulse=10kHz www.rohm.com 100 Fig. 135 Output Noise Spectrl Density VS Freq. Fig. 138 Load Response © 2009 ROHM Co., Ltd. All rights reserved. 10 Frequency f [kHz] 18/27 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series ●Reference data BU30TA2WNVX / HFV (Unless otherwise specified, Ta=25℃) Fig. 142 Load Response Current Pulse=100kHz Fig. 144 Start Up Time Iout = 0mA Fig. 147 Start Up Time(STBY=VIN) Iout = 200mA www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. Fig. 143 Load Response Current Pulse=100kHz Fig. 145 Start Up Time Iout = 200mA Fig. 148 Discharge Time Iout = 0mA 19/27 Fig. 146 Start Up Time (STBY=VIN) Iout = 0mA Fig. 149 VIN Response Iout = 10mA 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series BU33TA2WNVX / HFV ●Reference data 3.5 100 3.35 3.34 2.5 2.0 IO=0uA IO=100uA IO=50mA IO=200mA 1.5 1.0 0.5 Temp.=25°C VIN = STBY IO=0uA IO=100uA IO=50mA IO=200mA 3.33 3.32 3.31 3.30 3.29 3.28 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 40 Temp.=-40°C Temp.=25°C Temp.=85°C 3.3 3.4 3.5 3.6 0 3.7 0.5 1 1.5 2.5 110 Temp.=25°C 0.20 0.15 Temp.=-40°C 0.10 VIN=0.98 x VOUT STBY = 1.5V 0.05 Temp.=85°C 8 Gnd Current (uA) STBY Current (uA) Temp.=85°C Temp.=25°C 6 Temp.=-40°C 4 0.1 0.15 5.5 Temp.=-40°C 80 70 60 VIN = 4.3V STBY = 1.5V 40 0 0.5 1 1.5 Output Current (A) 2 2.5 3 3.5 4 4.5 5 0 5.5 0.05 V STBY Voltage (V) 0.1 0.15 0.2 Output Current (A) Fig. 154 STBY Input Current Fig. 153 Dropout Voltage Fig. 155 IOUT - IGND 3.50 3.50 3.35 5 Temp.=25°C 90 50 0.2 4.5 Temp.=85°C 2 0 0.05 4 100 VIN = STBY 0.00 0 3.5 120 10 0.30 0.25 3 Fig. 152 Circuit Current IGND Fig. 151 Line Regulation 0.35 2 Vin Voltage (V) Vin Voltage (V) Fig. 150 Output Voltage IO=0uA VIN = STBY 0 3.2 Vin Voltage (V) Dropout Voltage (V) 60 Temp=25°C VIN = STBY 3.25 0 80 20 3.27 3.26 0.0 Gnd Current (uA) Output Voltage (V) 3.0 Output Voltage (V) (Unless otherwise specified, Ta=25℃) VIN=4.3V 3.00 3.32 Temp.=25°C Temp.=-40°C 3.31 3.30 3.29 3.28 Temp.=85°C 3.27 VIN = 4.3V STBY = 1.5V 3.26 3.00 VIN=3.8V VIN=5.5V 2.50 VIN=4.3V 2.00 1.50 1.00 STBY = 1.5V 0.50 3.25 Output Voltage (V) 3.33 Output Voltage (V) Output Voltage (V) 3.34 0.05 0.1 0.15 0.1 0.2 Temp.=85°C Temp.=25°C Temp.=-40°C 1.00 0.3 0.4 0.5 0.6 0 0.5 Output Current (A) Output Current (A) Fig. 156 Load Regulation 1 1.5 STBY Voltage (V) Fig. 158 STBY Threshold Fig. 157 OCP Threshold 3.35 50.00 1.000 3.34 0.900 3.32 3.31 3.30 3.29 3.28 VIN=4.3V STBY=1.5V Io=0.1mA 3.27 3.26 0.800 40.00 30.00 20.00 VIN=4.3V STBY=1.5V Io=0mA 10.00 3.25 Gnd Current (uA) 3.33 Gnd Current (uA) Output Voltage (V) 1.50 0.00 0 0.2 2.00 0.50 Temp=25℃ 0.00 0 2.50 -15 10 35 60 85 Temp. (°C) Fig. 159 VOUT vs Temp www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 0.600 0.500 0.400 0.300 VIN=4.3V STBY=0V 0.200 0.100 0.000 0.00 -40 0.700 -0.100 -40 -15 10 35 60 Temp. (°C) Fig. 160 IGND vs Temp 20/27 85 -40 -15 10 35 60 85 Temp. (°C) Fig. 161 IGND vs Temp (STBY) 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series ●Reference data BU33TA2WNVX / HFV (Unless otherwise specified, Ta=25℃) 80 1.8 70 60 Ripple Rejection [dB] R ipple R e je c tio n (dB ) f= 1 kHz 50 40 30 Vin= 4.3V Io=10mA Ta = 25℃ 20 10 60 f= 0 .1 kHz 50 f= 1 0 kHz 40 30 f= 1 0 0 kHz 20 10 Co=1.0μF Cin=none Iout=10mA temp=25℃ 0 0 3.3 0.1 1 10 100 1000 Frequency (kHz) Fig. 162 Ripple Rejection VS Freq. 4.3 5.3 Input Voltage VIN[V] Fig. 163 Ripple Rejection VS VIN Fig. 165 Load Response O u tpu t N o ise D e n sity [μ V / √ H z ] 80 70 1.6 Co=1.0μF Cin=1.0μF Iout=10mA temp=25℃ 1.4 1.2 1 0.8 0.6 0.4 0.2 0 0.1 1 Fig. 166 Load Response Fig. 168 Load Response Fig. 169 Load Response Current Pulse=10kHz Fig. 170 Load Response Current Pulse=10kHz www.rohm.com 100 Fig. 164 Output Noise Spectrl Density VS Freq. Fig. 167 Load Response © 2009 ROHM Co., Ltd. All rights reserved. 10 Frequency f [kHz] 21/27 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series ●Reference data BU33TA2WNVX / HFV (Unless otherwise specified, Ta=25℃) Fig. 172 Load Response Current Pulse=100kHz Fig. 171 Load Response Current Pulse=100kHz Fig. 173 Start Up Time Iout = 0mA Fig. 176 Start Up Time(STBY=VIN) Iout = 200mA www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. Fig. 174 Start Up Time Iout = 200mA Fig. 177 Discharge Time Iout = 0mA 22/27 Fig. 175 Start Up Time (STBY=VIN) Iout = 0mA Fig. 178 VIN Response Iout = 10mA 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series ●About power dissipation (Pd) As for power dissipation, an approximate estimate of the heat reduction characteristics and internal power consumption of IC are shown, so please use these for reference. Since power dissipation changes substantially depending on the implementation conditions (board size, board thickness, metal wiring rate, number of layers and through holes, etc.), it is recommended to measure Pd on a set board. Exceeding the power dissipation of IC may lead to deterioration of the original IC performance, such as causing operation of the thermal shutdown circuit or reduction in current capability. Therefore, be sure to prepare sufficient margin within power dissipation for usage. Calculation of the maximum internal power consumption of IC (PMAX) PMAX=(VIN-VOUT)×IOUT(MAX.) (VIN: Input voltage VOUT: Output voltage IOUT(MAX): Maximum output current) ○ SSON004X1216 Measurement conditions Evaluation Board 1 (Single-side Board) Evaluation Board 2 (Double-side Board) 40 40 20 20 40 20 40 20 Layout of Board for Measurement (Unit: mm) Top Layer (Top View) Top Layer (Top View) 40 40 20 IC Implementation Position 40 40 20 Bottom Layer (Top View) Bottom Layer (Top View) Measurement State With board implemented (Wind speed 0 m/s) With board implemented (Wind speed 0 m/s) Board Material Glass epoxy resin (Single-side board) Glass epoxy resin (Double-side board) Board Size 40 mm x 40 mm x 0.8 mm 40 mm x 40 mm x 0.8 mm Top layer Metal (GND) wiring rate: Approx. 25% Metal (GND) wiring rate: Approx. 25% Bottom layer Metal (GND) wiring rate: Approx 0% Metal (GND) wiring rate: Approx 25% 0 holes Wiring Rate Power Dissipation 1100 mW Diameter 0.5 mm 12 holes 1250 mW Thermal Resistance θja=91°C/W θja=80°C/W Through Hole 1500 1250 mW Evaluation board 2 (Double-side board) 1000 Pd (mW) 1100 mW * Please design the margin so that PMAX becomes is than Pd (PMAXPd) within the usage temperature range. Evaluation board 1 (Single-side board) 500 - Standard ROHM board Size: 70 mm 70 mm 1.6 mm Material: Glass epoxy board Standard ROHM board 220 mW 0 0 25 50 75 100 125 Ta ( ℃) Fig.179 SSON004X1216 www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. Power dissipation heat reduction characteristics (Reference) 23/27 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series HVSOF5 Pd（W) ○ * Please design the margin so that PMAX becomes is than Pd (PMAXPd) within the usage temperature range. Fig.180 HVSOF5 Power dissipation heat reduction characteristics (Reference) ●DEVICE TYPE & Mark ○SSON004X1216 Device type: ○HVSOF5 BUXXTA2WNVX Device typce: BUXXTA2WHFV a a package a www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. XX output voltage SSON004 X1216 HVSOF5 15 1.5V typ. AA BA 18 1.8V typ. AB BB 23 2.3V typ. AG BC 25 2.5V typ. AC BD 26 2.6V typ. AD BE 27 2.7V typ. AE BF 28 2.8V typ. AF BG 2J 2.85V typ. AG BH 29 2.9V typ. AH BJ 30 3.0V typ. AJ BK 31 3.1V typ. AK BL 32 3.2V typ. AL BM 33 3.3V typ. AM BN 34 3.4V typ. AN BP 24/27 2009.05 - Rev.B BUTA2WNVX Series, BUTA2WHFV Series ○ Technical Note SSON004X1216 Mark Lot No. ○ HVSOF5 標印 Makrk Lot No. www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 25/27 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series Other notes - About absolute maximum rating Breakage may occur when absolute maximum ratings such as applied voltage and operating temperature range are exceeded. Short mode or open mode cannot be specified at occurrence of a break, so please prepare physical safety measures (e.g., fuse) if such special mode in which the absolute maximum rating is exceeded can be assumed. - About GND potential Please be sure that the potential of the GND terminal is the lowest in any operating condition. - About thermal design Please provide thermal design with sufficient margin, taking power dissipation (Pd) in actual usage conditions into consideration. - About short between pins and misattachment Please be careful regarding the IC direction and misalignment at attachment onto a printed circuit board. Misattachment may cause a break of IC. Short caused by foreign matter between outputs, output and power supply, or GNDs may also lead to a break. - About operation in a strong electromagnetic field Please note that usage in a strong electromagnetic field may cause malfunction. - About common impedance Please give due consideration to wiring of the power source and GND by reducing common-mode ripple or making ripple as small as possible (e.g., making the wiring as thick and short as possible, or reducing ripple by LC), etc. - About STBY terminal voltage Set STBY terminal voltage to 0.3 V or less to put each channel into a standby state and to 1.5 V or more to put each channel into an operating state. Do not fix STBY terminal voltage to 0.3 V or more and 1.5 V or less or do not lengthen the transition time. This may cause malfunction or failure. When shorting the VIN terminal and STBY terminal for usage, the status will be “STBY=VIN＝LOW” at turning the power OFF, and discharge of the VOUT terminal cannot operate, which means voltage may remain for a certain time in the VOUT terminal. Since turning the power ON again in this state may cause overshoot, turn the power ON for use after the VOUT terminal is completely discharged. - About overcurrent protection circuit Output has a built-in overcurrent protection circuit, which prevents IC break at load short. Note that this protection circuit is effective for prevention of breaks due to unexpected accidents. Please avoid usage by which the protection circuit operates continuously. - About thermal shutdown Output is OFF when the thermal circuit operates since a temperature protection circuit is built in to prevent thermal breakdown. However, it recovers when the temperature returns to a certain temperature. The thermal circuit operates at emergency such as overheating of IC. Since it is prepared to prevent IC breakdown, please do not use it in a state in which protection works. Reverse current About reverse current For applications on which reverse current is assumed to flow into IC, it is recommended to prepare a path to let the current out by putting a bypass diode between the VIN-VOUT terminals. VIN STBY OUT GND Fig.181 Example of bypass diode connection About testing on a set board When connecting a capacitor to a terminal with low impedance for testing on a set board, please be sure to discharge for each process since IC may be stressed. As a countermeasure against static electricity, prepare grounding in the assembly process and take sufficient care in transportation and storage. In addition, when connecting a capacitor to a jig in a testing process, please do so after turning the power OFF and remove it after turning the power OFF. www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 26/27 2009.05 - Rev.B Technical Note BUTA2WNVX Series, BUTA2WHFV Series ●Selection of order type B 1 U ROHM type 5 T A 2 Output voltage 15 : 1.5V 18 : 1.8V 25 : 2.5V 26 : 2.6V 27 : 2.7V 28 : 2.8V 2J : 2.85V 29 : 2.9V 30 : 3.0V 31 : 3.1V 32 : 3.2V 33 : 3.3V 34 : 3.4V W Lineup High-speed Load Response Full CMOS LDO Regulators N V X T Package NVX : SSON004X1216 HFV : HVSOF5 R Package specification TR : reel shape emboss taping SSON004X1216 <Tape and Reel information> 1.6 ± 0.1 1.2±0.1 Tape Embossed carrier tape Quantity 5000pcs Direction of feed 0.6MAX 1PIN MARK 1 2 4 3 +0.03 0.02 -0.02 0.65±0.1 ) 0.8 ± 0.1 0.2 ± 0.1 0.08 S +0.05 0.2 -0.04 The direction is the 1pin of product is at the upper right when you hold ( reel on the left hand and you pull out the tape on the right hand (0.12) S TR Direction of feed 1pin 0.75±0.1 Reel (Unit : mm) ∗ Order quantity needs to be multiple of the minimum quantity. HVSOF5 1.0±0.05 3000pcs 4 4 (0.91) 5 0.2MAX Embossed carrier tape Quantity (0.05) Tape (0.3) 5 (0.41) 1.6±0.05 (0.8) Direction of feed TR The direction is the 1pin of product is at the upper right when you hold ( reel on the left hand and you pull out the tape on the right hand ) 3 2 1 1 2 3 1pin 0.13±0.05 S +0.03 0.02 –0.02 0.6MAX 1.2±0.05 (MAX 1.28 include BURR) <Tape and Reel information> 1.6±0.05 0.1 S 0.5 0.22±0.05 0.08 Direction of feed M (Unit : mm) www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. Reel 27/27 ∗ Order quantity needs to be multiple of the minimum quantity. 2009.05 - Rev.B Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. R0039A