Series AM15EW-IZ 15 Watt | DC-DC Converter FEATURES: RoHS compliant Wide 4:1 input range Low ripple and noise Remote On/Off control Power modules for PCB mounting Regulated output Operating temperature range: -40 to +85ºC Capacitive loading up to 4500 µF (18-75V input) Models Single output Model AM15EW-2403SIZ AM15EW-2405SIZ AM15EW-2412SIZ AM15EW-2415SIZ AM15EW-4803SIZ AM15EW-4805SIZ AM15EW-4812SIZ AM15EW-4815SIZ AM15EW-11005SIZ AM15EW-11012SIZ AM15EW-11015SIZ AM15EW-11024SIZ AM15EW-2403SH30IZ AM15EW-2405SH30IZ AM15EW-2412SH30IZ AM15EW-2415SH30IZ AM15EW-4803SH30IZ AM15EW-4805SH30IZ AM15EW-4812SH30IZ AM15EW-4815SH30IZ Input Voltage (V) Output Voltage (V) Output Current max (A) Ripple & Noise typ Isolation (VDC) Efficiency (%) 9-36 9-36 9-36 9-36 18-75 18-75 18-75 18-75 36-160 36-160 36-160 36-160 3.3 5 12 15 3.3 5 12 15 5 12 15 24 4 3 1.25 1 4 3 1.25 1 3 1.25 1 0.625 80mV p-p 80mV p-p 120mVp-p 150mVp-p 80mV p-p 80mV p-p 120mVp-p 150mVp-p 80mV p-p 120mVp-p 150mVp-p 240mVp-p 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 77 80 85 84 77 80 85 84 80 82 80 80 9-36 9-36 9-36 9-36 18-75 18-75 18-75 18-75 3.3 5 12 15 3.3 5 12 15 4 3 1.25 1 4 3 1.25 1 80mV p-p 120mVp-p 150mVp-p 240mVp-p 80mV p-p 120mVp-p 150mVp-p 240mVp-p 3000 3000 3000 3000 3000 3000 3000 3000 74 78 80 83 76 75 79 83 Input Voltage (V) Output Voltage (V) Ripple & Noise typ Isolation (VDC) Efficiency (%) Models Dual output Model AM15EW-2405DIZ AM15EW-2412DIZ AM15EW-2415DIZ AM15EW-4805DIZ AM15EW-4812DIZ AM15EW-4815DIZ AM15EW-11005DIZ AM15EW-11012DIZ AM15EW-11015DIZ AM15EW-2405DH30IZ AM15EW-2412DH30IZ AM15EW-2415DH30IZ AM15EW-4805DH30IZ AM15EW-4812DH30IZ AM15EW-4815DH30IZ Output Current max (A) 9-36 9-36 9-36 18-72 18-72 18-72 36-160 36-160 36-160 ±5 ±12 ±15 ±5 ±12 ±15 ±5 ±12 ±15 ±1.5 ±0.625 ±0.5 ±1.5 ±0.625 ±0.5 ±1.5 ±0.62 ±0.5 50mVp-p 120mVp-p 150mVp-p 50mVp-p 120mVp-p 150mVp-p 50mVp-p 120mVp-p 150mVp-p 1500 1500 1500 1500 1500 1500 1500 1500 1500 80 85 84 80 85 84 78 80 81 9-36 9-36 9-36 18-72 18-72 18-72 ±5 ±12 ±15 ±5 ±12 ±15 ±1.5 ±0.62 ±0.5 ±1.5 ±0.62 ±0.5 50mVp-p 120mVp-p 150mVp-p 50mVp-p 120mVp-p 150mVp-p 3000 3000 3000 3000 3000 3000 79 83 83 78 80 82 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. www.aimtec.com F 051e R8.F Tel: +1 514 620 2722 1 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM15EW-IZ 15 Watt | DC-DC Converter Input Specifications Parameters Nominal Typical 24 48 110 Voltage range Maximum 9-36 18-75 36-160 Units VDC (Pi) Network Filter 24 Vin 48 Vin 110 Vin Absolute Maximum Rating 40 83 220 2 Permissible absolute maximum duration VDC h Isolation Specifications Parameters Tested I/O voltage Resistance Capacitance Conditions 60 sec Typical Rated 1500 & 3000 > 1000 1000 Units VDC MOhm pF 1500 Output Specifications Parameters Voltage accuracy Short Circuit protection Short Circuit restart Over voltage protection Over load protection Line voltage regulation (Single) Line voltage regulation (Dual) Load voltage regulation (Single) Load voltage regulation (Dual) Temperature coefficient Recommended Input Fuse (slow blow) Conditions Typical Maximum ±2 Auto recovery HL-LL HL-LL 25-100% 25-100% 24 Vin 48 Vin 110 Vin Units % Continuous Auto recovery Zener diode clamp protection Over 110% full load ±0.5 ±0.5 ±0.5 ±2 ±0.05 4A/250V 2A/250V 1A/250V % % % % %/oC General Specifications Parameters Switching frequency Operating temperature Storage temperature Max Case temperature Cooling Humidity Case material Weight Dimensions(L x W x H) MTBF Conditions Typical 100% load With derating above +75 200 Maximum -40 to +85 -55 to +115 95 Units KHz o C o C o C Free air convection 95 % Nickel coated copper with non-conductive base 33 g Tolerance ±0.5mm 2.00 x 1.00 x 0.40 inches 50.80 x 25.40 x 10.50 mm > 800 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25oC) Safety Specifications Parameters Agency Approvals Standards www.aimtec.com F 051e R8.F CE EN 55022, EN 55024 IEC61000-3-2 IEC61000-3-3 IEC61000-4-2, Perf. Criteria B IEC61000-4-3 Perf. Criteria A IEC61000-4-4, Perf. Criteria B IEC61000-4-6, Perf. Criteria A IEC61000-4-8, Perf. Criteria A NOTE: also designed to meet standard IEC 60950-1:2001 Tel: +1 514 620 2722 2 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM15EW-IZ 15 Watt | DC-DC Converter Pin Out Specifications Pin Single Dual 1 2 3 4 5 6 On/Off Control -V Input +V Input -V Output No pin +V Output On/Off Control -V Input +V Input -V Output Common +V Output Dimensions 1 5 4 20.32 (0.80) 15.24 (0.60) 10.16 (0.40) Bottom View 2.54 (0.10) 2 10.16 (0.40) 3 7.62 5.08 (0.30) (0.20) 25.40 (1.00) 10.16 (0.40) 6 15.24 (0.60) Notes: All dimensions are typical in millimeters (inches). Tolerance ±0.25 (±0.01) 6.00 (0.24) 10.50 (0.41) DIA 1.00 (0.04) 2.54 (0.10) 50.80 (2.00) Derating Free Air Convection 50º C Output Power (%) 100 80 Safe Operating Area 60 40 20 0 - 40 - 20 0 20 40 60 80 85 100 Ambient Temperature º C www.aimtec.com F 051e R8.F Tel: +1 514 620 2722 3 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM15EW-IZ 15 Watt | DC-DC Converter Block diagram NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R8.F Tel: +1 514 620 2722 4 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only