Vitec MTWA11-S03 10w wall mount power supply for i.t. equipment Datasheet

MTWA11 SERIES
10W Wall Mount Power Supply for I.T. Equipment
–
–
–
–
–
–
–
1 Year Warranty
Wide Input Voltage 90 to 264 VAC, 47 to 63Hz
European type 2 prong plug
Output Voltage Available From 5VDC Thru 48VDC
Optional Output Connector (See appendix)
Single Output
Class II Insulation
CEC Level V, Energy Star 2.0, and RoHS Compliance
Approvals:
Single Output
Product Number
Output Voltage
Max. Output Current
MTWA11-S02
5 ~ 6 VDC
1.60 ~ 1.33 A
MTWA11-S03
6 ~ 8 VDC
1.33 ~ 1.00 A
MTWA11-S04
8 ~ 11 VDC
1.25 ~ 0.91 A
MTWA11-S05
11 ~ 13 VDC
0.91 ~ 0.77 A
MTWA11-S06
13 ~ 16 VDC
0.77 ~ 0.63 A
MTWA11-S07
16 ~ 21 VDC
0.63 ~ 0.48 A
MTWA11-S08
21 ~ 27 VDC
0.48 ~ 0.37 A
MTWA11-S09
27 ~ 33 VDC
0.37 ~ 0.30 A
MTWA11-S10
33 ~ 40 VDC
0.30 ~ 0.25 A
MTWA11-S11
40 ~ 48 VDC
0.25 ~ 0.20 A
The total regulation on model S02-S05 is required to use AWG#20/4FT output cable.
The total regulation on model S06-S10 is required to use AWG#24/4FT output cable.
The regulation and efficiency will be changed by modified output cable.
Total Regulation
Maximum Output Power
5%
5%
5%
5%
5%
3%
3%
3%
3%
3%
8W
8W
10W
10W
10W
10W
10W
10W
10W
10W
Electrical Characteristics
Parameter
Input Voltage
Input Frequency
Output Power Range
Input Current (Low Line)
Input Current (High Line)
Low Line Inrush Current
High Line Inrush Current
Efficiency
Line Regulation
Load Regulation
Over Voltage Protection
Over Current Protection
Transient Response
Hold-Up Time
Start Up Time
* Ripple & Noise (Peak to Peak)
Safety Ground Leakage Current
No-Load Power Consumption
Temperature Coefficient
Test Conditions
Operating Voltage
Vin=90 to 264VAC
Io=Full load, Vin=115VAC
Io=Full load, Vin=230VAC
Io=Full load, 25°C, Cool start, Vin=115VAC
Io=Full load, 25°C, Cool start, Vin=230VAC
Io=Full Load, Vin=230VAC
Io=Full Load
Vin=230VAC
Nil But, Output protected to short circuit conditions
Io=Full Load to Half Load, Vin=100VAC
Io=Full Load, Vin=110VAC
Io=Full Load, Vin=100VAC
Full Load, Vin=90VAC
Io=Full Load, Vin=240VAC
No load,Vin=240VAC
All output
Min.
Typ.
90
47
0
71
35
70
76
0.5
3
Nil
Max.
Unit
264
63
10
0.3
0.2
40
80
85
1
5
VAC
Hz
W
A
A
A
A
%
%
%
%
%
mS
mS
S
%
mA
W
%/°C
4
5
-0.04
10
2
0.5
0.2
0.2
3
1
0.25
0.3
0.04
Conditions
Parameter
Test Conditions
Operating Temperature
Storage Temperature
Relative Humidity
No-Condensing
Operating Temperature at 25°C, Calculated per MIL-HDBK-217F
De-rate linearly from 100% load at 40°C to 50% load at 70°C
Min.
Typ.
Max.
Unit
0
-40
5
0.1
40
70
85
95
°C
°C
%
M Hrs
Min.
Unit
4242
B
B
VDC
CLASS
CLASS
Approvals and Compliance
Parameter
Dielectric Withstanding Voltage for Primary to secondary
EMI requirements for CISPR-22
EMI requirements for FCC PART-15
Test Conditions
Primary to secondary
Vin=220VAC
Vin=110VAC
Mechanical and PIN out
Note:
1.
Dimensions are shown in mm.
2.
Weight: 90g approx.
3.
Optional output connector.
Similar pages