NICHIA STS-DA1-2080 <Cat.No.111130> NICHIA CORPORATION SPECIFICATIONS FOR WHITE LED NSPW515DS ● RoHS Compliant NICHIA STS-DA1-2080 <Cat.No.111130> SPECIFICATIONS (1) Absolute Maximum Ratings Symbol Absolute Maximum Rating Unit Forward Current Item IF 30 mA Pulse Forward Current IFP 100 mA Reverse Voltage VR 5 V Power Dissipation PD 105 mW Operating Temperature Topr -30~85 °C Storage Temperature Tstg -40~100 °C Junction Temperature TJ 100 °C * Absolute Maximum Ratings at TA=25°C. * IFP conditions with pulse width ≤10ms and duty cycle ≤10%. (2) Initial Electrical/Optical Characteristics Symbol Condition Typ Unit Forward Voltage Item VF IF=20mA 3.2 V Luminous Intensity Iv IF=20mA 2.3 cd x - IF=20mA 0.31 - y - IF=20mA 0.32 - Chromaticity Coordinate * Characteristics at TA=25°C. * Chromaticity Coordinates as per CIE 1931 Chromaticity Chart. 1 NICHIA STS-DA1-2080 <Cat.No.111130> RANKS Item Rank Min Max Unit Forward Voltage - 2.65 3.50 V Reverse Current - - 50 µA W 2.32 3.22 V 1.61 2.32 U 1.16 1.61 Luminous Intensity cd Color Ranks Rank a0 Rank b1 x 0.280 0.264 0.283 0.296 x 0.287 0.283 0.330 0.330 y 0.248 0.267 0.305 0.276 y 0.295 0.305 0.360 0.339 Rank b2 Rank c0 x 0.296 0.287 0.330 0.330 x 0.330 0.330 0.361 0.356 y 0.276 0.295 0.339 0.318 y 0.318 0.360 0.385 0.351 * Ranking at TA=25°C. * Reverse Current at VR=5V. * Tolerance of measurements of the Forward Voltage is ±3%. * Tolerance of measurements of the Luminous Intensity is ±10%. * Tolerance of measurements of the Chromaticity Coordinate is ±0.01. * A shipment shall consist of LEDs in a combination of the above ranks. The percentage of each rank in the shipment shall be determined by Nichia. 2 NICHIA STS-DA1-2080 <Cat.No.111130> CHROMATICITY DIAGRAM 0.45 0.40 c0 0.35 y b1 b2 0.30 a0 0.25 0.20 0.20 0.25 0.30 0.35 0.40 0.45 x 3 NICHIA STS-DA1-2080 <Cat.No.111130> OUTLINE DIMENSIONS * 本製品はRoHS指令に適合しております。 This product complies with RoHS Directive. 管理番号 No. NSPW515DS STS-DA7-1865 (単位 Unit:±0.2) mm) (単位 Unit: mm, 公差 Tolerance: 1.5 MAX 1 5.6 5.3 Φ5 1.1 (2.5) Cathode □0.5±0.05 Anode 7.3 8.3 12.1±0.5 (2) 28.6±1 樹脂材質 Resin Materials エポキシ樹脂(一部蛍光体入り) Epoxy Resin(partly using phosphor) レンズ色 Lens Color 乳白色(拡散剤入り) Milky(with diffuser) リードフレーム材質 Lead Frame Materials 銅合金+銀メッキ Ag-plated Copper Alloy 質量 Weight 0.29g(TYP) * タイバーを切り取った部分は銅合金が露出しております。 またLEDには鋭利な部分があります。特にリード部分は、人体を傷つける ことがありますので、取り扱いに際しては十分注意して下さい。 The tie bar cut-end surface exhibits exposed copper alloy base metal. Care must be taken to handle the LEDs, as it may contain sharp parts such as lead, and can cause injury. 0.3 内容 Description 0.3 項目 Item ストッパー部詳細図 Lead Standoff 1 4 NICHIA STS-DA1-2080 <Cat.No.111130> SOLDERING • Recommended Hand Soldering Condition • Recommended Dip Soldering Condition Temperature 350°C Max Pre-Heat 120°C Max Soldering Time 3sec Max Pre-Heat Time 60sec Max No closer than 3mm from Solder Bath the base of the lens. Temperature Position Dipping Time Dipping Position 260°C Max 10sec Max No closer than 3mm from the base of the lens. * For a better thermal performance, copper alloy is used for the leadframe of the product. Care must be taken for the soldering conditions and handling of the products after soldering. * Solder the LED no closer than 3mm from the base of the lens. Soldering beyond the base of the tie bar is recommended. * Dip soldering/hand soldering must not be performed more than once. * Care should be taken to avoid cooling at a rapid rate and ensure the peak temperature ramps down slowly. * When soldering, do not apply stress to the lead frame while the LED is hot. * After soldering, the LED position must not be corrected. * After soldering, NO mechanical shock or vibration should be applied to LED lens until the LEDs cool down to room temperature. * In order to avoid damage on the lens during cutting and clinching the leads, it is not recommended to solder the LEDs directly on customer PCB without any gap between the lens and the board. If it is unavoidable, customer is advised to check whether such soldering will not cause wire breakage or lens damage. Direct soldering to double-sided PCBs must be avoided due to an increased effect of heat on the lens. * When it is necessary to clamp the LEDs to prevent soldering failure, it is important to minimize the mechanical stress on the LEDs. * Cut the LED lead frames at room temperature. Cutting the lead frames at high temperature may cause failure of the LEDs. 5 NICHIA STS-DA1-2080 <Cat.No.111130> PACKAGING - BULK 管理番号 No. Nxxxxxxx STS-DA7-0001B 袋の表示 Label printed on the bag 帯電防止袋 Anti-electrostatic Bag XXXX LED Type Nxxxxxxx ******* Lot YMxxxx-RRR Qty pcs RoHS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN CAUTION TO ELECTROSTATIC DAMAGE 静電気に注意 帯電防止袋を並べて入れ、ダンボールで仕切ります。 Anti-electrostatic bags are packed in cardboard boxes with corrugated partitions. ラベル Label attached to the box XXXX LED TYPE Nxxxxxxx ******* RANK RRR QTY. PCS RoHS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Nichia LED * 客先型名を*******で示します。 客先型名が設定されていない場合は空白です。 ******* is the customer part number. If not provided, it is not indicated on the label. * ロット表記方法についてはロット番号の項を 参照して下さい。 For details, see "LOT NUMBERING SCHEME" in this document. * 本製品は帯電防止袋に入れたのち、輸送の衝撃から保護するためダンボールで梱包します。 Products are packed in an anti-electrostatic bag. They are shipped in cardboard boxes to protect them from external forces during transportation. * 取り扱いに際して、落下させたり、強い衝撃を与えたりしますと、製品を損傷させる原因になりますので注意して下さい。 Do not drop or shock the box. It may damage the products. * ダンボールには防水加工がされておりませんので、梱包箱が水に濡れないよう注意して下さい。 Do not expose to water, the box is not water-resistant. * 輸送、運搬に際して弊社よりの梱包状態あるいは同等の梱包を行って下さい。 Using an original packaging material or equivalent in transit is recommended. 6 NICHIA STS-DA1-2080 <Cat.No.111130> LOT NUMBERING SCHEME Lot Number is presented by using the following alphanumeric code. YMxxxx - RRR Y - Year Year Y 2009 9 2010 A 2011 B 2012 C 2013 D 2014 E M - Month Month M Month M 1 1 7 7 2 2 8 8 3 3 9 9 4 4 10 A 5 5 11 B 6 6 12 C xxxx-Nichia's Product Number RRR-Ranking by Color Coordinates, Ranking by Luminous Intensity 7 NICHIA STS-DA1-2080 <Cat.No.111130> DERATING CHARACTERISTICS 管理番号 No. NSPW515D(S) STS-DA7-1813 周囲温度-許容順電流特性 Ambient Temperature vs Allowable Forward Current Derating1 許容順電流 Allowable Forward Current(mA) 50 40 (47, 30.0) 30 20 10 (85, 8.50) 0 0 20 40 60 80 100 120 周囲温度 Ambient Temperature(°C) デューティー比-許容順電流特性 Duty Ratio vs Allowable Forward Current Duty TA =25°C 許容順電流 Allowable Forward Current(mA) 1000 100 30 10 1 10 100 デューティー比 Duty Ratio(%) 8 NICHIA STS-DA1-2080 <Cat.No.111130> OPTICAL CHARACTERISTICS * 本特性は参考です。 All characteristics shown are for reference only and are not guaranteed. 管理番号 No. 発光スペクトル Spectrum NSPW515D(S) STS-DA7-1814 T A=25°C IF=20mA Spectrum 1.0 相対発光強度 Relative Emission Intensity(a.u.) 0.8 0.6 0.4 0.2 0.0 350 400 450 500 550 600 650 700 750 波長 Wavelength(nm) Directivity1 指向特性 Directivity T A=25°C IFP=20mA -20° -10° 0° 10° 20° 30° -30° 40° -40° 50° 放射角度 Radiation Angle -50° -60° 60° 70° -70° 80° -80° -90° 90° 1 0.5 0 0.5 1 相対光度 Relative Luminosity(a.u.) 9 NICHIA STS-DA1-2080 <Cat.No.111130> FORWARD CURRENT CHARACTERISTICS / TEMPERATURE CHARACTERISTICS * 本特性は参考です。 All characteristics shown are for reference only and are not guaranteed. 順電圧-順電流特性 Forward Voltage vs Forward Current 管理番号 No. 周囲温度-順電圧特性 Ambient Temperature vs Forward Voltage VfIf T A=25°C 100 NSPW515D(S) STS-DA7-1815 IFP= 5mA IFP=20mA IFP= 60mA TaVf 4.5 順電圧 Forward Voltage(V) 順電流 Forward Current(mA) 4.0 20 10 3.5 3.0 1 2.5 2.5 3.0 3.5 4.0 4.5 -60 -40 -20 順電圧 Forward Voltage(V) 20 40 60 80 100 120 周囲温度 Ambient Temperature(°C) 周囲温度-相対光度特性 順電流-相対光度特性 Forward Current vs Relative Luminosity Ambient Temperature vs Relative Luminosity IfIv T A=25°C TaIv IFP= 20mA 1.4 5 相対光度 Relative Luminosity(a.u.) 4 相対光度 Relative Luminosity(a.u.) 0 3 2 1.2 1.0 0.8 1 0.6 0 0 20 40 60 80 順電流 Forward Current(mA) 100 120 -60 -40 -20 0 20 40 60 80 100 120 周囲温度 Ambient Temperature(°C) 10 NICHIA STS-DA1-2080 <Cat.No.111130> FORWARD CURRENT CHARACTERISTICS / TEMPERATURE CHARACTERISTICS * 本特性は参考です。 All characteristics shown are for reference only and are not guaranteed. 順電流-色度特性 Forward Current vs Chromaticity Coordinate 管理番号 No. NSPW515D(S) STS-DA7-1816 Ifxy TA =25°C 0.34 1mA 0.33 y 5mA 20mA 0.32 30mA 0.31 100mA 0.30 0.29 0.30 0.31 0.32 0.33 x 周囲温度-色度特性 Ambient Temperature vs Chromaticity Coordinate Taxy I FP= 20mA 0.34 -30°C 0.33 y 0°C 0.32 25°C 50°C 0.31 0.30 0.29 85°C 0.30 0.31 0.32 0.33 x 11 NICHIA STS-DA1-2080 <Cat.No.111130> RELIABILITY (1) Tests and Results Reference Test Test Test Conditions Standard Duration Resistance to JEITA ED-4701 Tsld=260±5°C, 10sec, 1dip, Soldering Heat 300 302 3mm from the base of the lens JEITA ED-4701 Tsld=245±5°C, 5sec, 303 303A Lead-free Solder(Sn-3.0Ag-0.5Cu) JEITA ED-4701 -40°C(30min)~25°C(5min)~ 100 105 100°C(30min)~25°C(5min) Moisture Resistance JEITA ED-4701 25°C~65°C~-10°C, 90%RH, (Cyclic) 200 203 24hr per cycle Terminal Bend JEITA ED-4701 5N, 0°~90°~0°bend, Strength 400 401 2bending cycles Terminal Pull JEITA ED-4701 Strength 400 401 High Temperature JEITA ED-4701 Storage 200 201 Temperature Humidity JEITA ED-4701 Storage 100 103 Low Temperature JEITA ED-4701 Storage 200 202 Solderability Temperature Cycle Room Temperature Operating Life Temperature Humidity Operating Life Low Temperature Operating Life Failure Criteria # Units Failed/Tested #1 0/50 #2 0/50 100cycles #1 0/50 10cycles #1 0/50 #1 0/50 #1 0/50 10N, 10±1sec TA=100°C 1000hours #1 0/50 TA=60°C, RH=90% 1000hours #1 0/50 TA=-40°C 1000hours #1 0/50 TA=25℃, IF=30mA 1000hours #1 0/50 60°C, RH=90%, IF=20mA 500hours #1 0/50 TA=-30°C, IF=20mA 1000hours #1 0/50 NOTES: Measurements are performed after allowing the LEDs to return to room temperature. (2) Failure Criteria Criteria # Items Conditions Failure Criteria Forward Voltage(VF) IF=20mA >U.S.L.×1.1 #1 Luminous Intensity(IV) IF=20mA <L.S.L.×0.7 Reverse Current(IR) VR=5V >U.S.L.×2.0 #2 Solderability - Less than 95% solder coverage U.S.L. : Upper Specification Limit L.S.L. : Lower Specification Limit 12 NICHIA STS-DA1-2080 <Cat.No.111130> CAUTIONS (1) Lead Forming ● When forming leads, the leads should be bent at a point at lease 3mm from the base of the epoxy bulb. Do not use the base of the leadframe as a fulcrum during lead forming. ● Lead forming should be done before soldering. ● Do not apply any bending stress to the base of the lead. The stress to the base may damage the LED's characteristics or it may break the LEDs. ● When mounting the product onto a printed circuit board, the via-holes on the board should be exactly aligned with the lead pitch of the product. If the LEDs are mounted with stress at the leads, it causes deterioration of the epoxy resin and this will degrade the LEDs. (2) Storage ● Shelf life of the products in unopened bag is 3 months(max.) at <30°C and 70% RH from the delivery date. If the shelf life exceeds 3 months or more, the LEDs need to be stored in a sealed container with silica gel desiccants to ensure their shelf life will not exceed 1 year. ● Nichia LED leadframe are silver plated copper alloy. This silver surface may be affected by environments which contain corrosive substances. Please avoid conditions which may cause the LED to corrode, tarnish or discolor. This corrosion or discoloration may cause difficulty during soldering operation. It is recommended that the LEDs be used as soon as possible. ● To avoid condensation, the products must not be stored in the areas where temperature and humidity fluctuate greatly. (3) Directions for Use ● When designing a circuit, the current through each LED must not exceed the Absolute Maximum Rating. Operating at a constant current per LED is recommended. In case of operating at a constant voltage, Circuit B is recommended. If the LEDs are operated with constant voltage using Circuit A, the current through the LEDs may vary due to the variation in Forward Voltage characteristics of the LEDs. (A) (B) ... ... ● LEDs should be operated in forward bias. Driving circuits must not subject LEDs to either forward or reverse voltage while off. Continuous reverse voltage can cause migration and LED damage. ● For stabilizing the LED characteristics, it is recommended to operate at greater than 10% nominal current. ● Care must be taken to ensure that the reverse voltage will not exceed the Absolute Maximum Rating when using the LEDs with matrix drive. ● For outdoor use, necessary measures should be taken to prevent water, moisture and salt air damage. (4) Handling Precautions ● Do not handle LEDs with bare hands, it may contaminate the LED surface and affect optical characteristics. In the worst case, catastrophic failure from excess pressure through wire-bond breaks and package damage may result. ● Dropping the product may cause damage. ● Do not stack assembled PCBs together. Failure to comply can cause the resin portion of the product to be cut, chipped, delaminated and/or deformed. It may cause wire to break, leading to catastrophic failures. (5) Design Consideration ● PCB warpage after mounting the products onto a PCB can cause the package to break. The LED should be placed in a way to minimize the stress on the LEDs due to PCB bow and twist. ● The position and orientation of the LEDs affect how much mechanical stress is exerted on the LEDs placed near the score lines. The LED should be placed in a way to minimize the stress on the LEDs due to board flexing. ● Board separation must be performed using special jigs, not using hands. 13 NICHIA STS-DA1-2080 <Cat.No.111130> (6) Electrostatic Discharge (ESD) ● The products are sensitive to static electricity or surge voltage. ESD can damage a die and its reliability. When handling the products, the following measures against electrostatic discharge are strongly recommended: Eliminating the charge Grounded wriststrap, ESD footwear, clothes, and floors Grounded workstation equipment and tools ESD table/shelf mat made of conductive materials ● Proper grounding is required for all devices, equipment, and machinery used in product assembly. Surge protection should be considered when designing of commercial products. ● If tools or equipment contain insulating materials such as glass or plastic, the following measures against electrostatic discharge are strongly recommended: Dissipating static charge with conductive materials Preventing charge generation with moisture Neutralizing the charge with ionizers ● The customer is advised to check if the LEDs are damaged by ESD when performing the characteristics inspection of the LEDs in the application. Damage can be detected with a forward voltage measurement or a light-up test at low current (≤1mA). ● ESD damaged LEDs may have an increased leakage current, current flow at a low voltage or no longer illuminate at a low current. Failure Criteria: VF<2.0V at IF=0.5mA (7) Thermal Management ● Proper thermal management is an important when designing products with LEDs. LED die temperature is affected by PCB thermal resistance and LED spacing on the board. Please design products in a way that the LED die temperature does not exceed the maximum Junction Temperature (TJ). ● Drive current should be determined for the surrounding ambient temperature (TA) to dissipate the heat from the product. (8) Cleaning ● If required, isopropyl alcohol (IPA) should be used. Other solvents may cause premature failure to the LEDs due to the damage to the resin portion. The effects of such solvents should be verified prior to use. In addition, the use of CFCs such as Freon is heavily regulated. ● Ultrasonic cleaning is not recommended since it may have adverse effects on the LEDs depending on the ultrasonic power and how LED is assembled. If ultrasonic cleaning must be used, the customer is advised to make sure the LEDs will not be damaged prior to cleaning. (9) Eye Safety ● In 2006, the International Electrical Commission (IEC) published IEC 62471:2006 Photobiological safety of lamps and lamp systems, which added LEDs in its scope. On the other hand, the IEC 60825-1:2007 laser safety standard removed LEDs from its scope. However, please be advised that some countries and regions have adopted standards based on the IEC laser safety standard IEC 60825-1:20112001, which still includes LEDs in its scope. Most of Nichia's LEDs can be classified as belonging into either the Exempt Group or Risk Group 1. High-power LEDs, that emit light containing blue wavelengths, may be classified as Risk Group 2. Please proceed with caution when viewing directly any LEDs driven at high current, or viewing LEDs with optical instruments which may greatly increase the damages to your eyes. ● Viewing a flashing light may cause eye discomfort. When incorporating the LED into your product, please be careful to avoid adverse effects on the human body caused by light stimulation. 14 NICHIA STS-DA1-2080 <Cat.No.111130> (10) Others ● The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment, communications equipment, measurement instruments and household appliances). Consult Nichia's sales staff in advance for information on the applications in which exceptional quality and reliability are required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control system, automobiles, traffic control equipment, life support systems and safety devices). ● The customer shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent from Nichia. When defective LEDs are found, the customer shall inform Nichia directly before disassembling or analysis. ● Both the customers and Nichia will agree on official specifications of supplied products before a customer's volume production. ● Specifications and appearance subject to change for improvement without notice. 15