APR3001/2/3 MicroPower Microprocessor Reset Circuit Features • • • • • • • • General Description 1.2V to 6V Input Voltage Range The APR3001/2/3 are designed to monitor voltage Low Quiescent Current : less Than 1.5 µA supplies in µP and digital systems. The quiescent High accuracy detection threshold : ±1.5% current is extremely low, typically 1.5 µA, making it Fixed trimmed reset thresholds for 1.5V, 1.75V, ideal for portable battery operated equipment. The 2.32V, 2.63V, 2.93V, 3.08V, 3.9V, 4.38V. APR3001/2/3 operate by monitoring the system Reset Timeout Period 250ms power supply voltage. When the input voltage drops Available output configurations below a fixed threshold, the device asserts a reset - Open-drain output - CMOS active high output - CMOS active low output signal for a fixed time period after Vcc rises above the fixed threshold. The APR3001/2/3 series is available with three output stage versions : APR3001 SOT-23 , SOT-23-5 and SOT-89 packages push-pull active low output, APR3002 push-pull ac- No external components tive high output and APR3003 open drain active low Applications output. They are also designed to reject fast line tran- • • • • a miniature SOT-23, SOT-23-5, SOT-89 packages. sient glitches on Vcc. The APR3001/2/3 are come in Computers Cell Phones Pin Configuration Portable Electronics µP Power Supply Monitoring NC V CC 3 5 1 2 1 (3 0 0 1 /3 ) R e s e t G N D (3 0 0 2 ) R e s e t (3001/3) Reset (3002) Reset 2 4 2 3 (3001/3) Reset V CC GND (3002) Reset SOT-23 (Top View) 1 NC SOT-23-5 (Top View) 3 V CC GND SOT-89 (Top View) ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 1 www.anpec.com.tw APR3001/2/3 Ordering and Marking Information Package Code A : SOT-23 B : SOT-23-5 D : SOT-89 Temp. Range I : -40 to 85 ° C Handling Code TR : Tape & Reel Voltage Code : 15 : 1.5V ~ 43 : 4.38V Lead Free Code L : Lead Free Device Blank : Original Device APR3001/2/3 Lead Free Code Handling Code Temp. Range Package Code Voltage Code APR3001/2/3 A/B : 01/2/3 X X APR3001/2/3 -15 D : Date Code Voltage Code A:1.5V B:1.75V C:2.32V D:2.63V E:2.93V F:3.08V G:3.9V H:4.38V APR3001/2/3 XXXXX 15 XXXXX - Date Code ; 15 - 1.5V Absolute Maximum Ratings Symbol VCC Parameter VCC to GND Value Unit -0.3 to 6 V VRESET RESET to GND (Push-Pull Output) RESET to GND (Open Drain Output) -0.3 to VCC +0.3 -0.3 to 6 V IMAX Maximum Continuous Input Current 20 mA RESET/RESET Current 20 mA Rate of Rise of VCC 100 V/µs -40 to 150 °C 260 357 357 180 Internally Limited °C IRESET dVcc/dt TJ Junction Temperature Range TL Lead Temperature (Soldering, 10 second) RTH,JA PD Thermal Resistance – Junction to Ambient SOT-23 SOT-23-5 SOT-89 Power Dissipation °C/W W Pin Function Descrpition No. 1 2 3 PIN Name RESET (APR3001/3) RESET (APR3002) GND VCC Description RESET output remains low while VCC is below the reset threshold and remains so for a fixed time period after VCC raises above the reset threshold RESET output remains high while VCC is below the reset threshold and remains so for a fixed time period after VCC raises above the reset threshold. Ground connection Supply Voltage (+1.2V to +6V) Note: The pin sequence here might not be correct for all different package types, and please refer pin configuration in page1 for correct pin assignment. Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 2 www.anpec.com.tw APR3001/2/3 Block Diagram Vc c Reset Generator + Timer RESET Oscillator VREF APR3001 GND Vc c Reset Generator + Timer RESET Oscillator VREF APR3002 GND RESET Vc c Reset Generator + Timer Oscillator VREF GND Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 APR3003 3 www.anpec.com.tw APR3001/2/3 Part Number Description Part Number APR3001 APR3002 APR3003 Part Description Reset Output Push Pull Active Low with Delay Reset Output Push Pull Active High with Delay Reset Output Open Drain Active Low with Delay Electrical Characteristics VIN = 5V, TA = -40 to 85°C unless otherwise noted. Typical values are at TA=25°C, VCC = 5V for 4.38V versions, VCC = 3.3V for 3.08/2.93V versions, VCC = 3.0V for 2.63V. versions and VCC = 2.5V for 2.32V versions, VCC = 2.0V for 1.75V versions , VCC = 1.8V for 1.5V versions. APR3001/2/3 Symbol Parameter Test Conditions Unit Min. Typ. Max. VCC 1.2 6 Supply Voltage V ICC Supply Current VCC=1.5V~6V 1.5 4 µA T A=-40 to 85°C 3 5 T A=25°C ±1.5% VTH Reset Threshold T A=-40 to 85°C ±2% VHYST Hysteresis Range 20 mV Reset Timeout Period ms TRTP 150 250 350 VOL Reset Output Low ISINK=1.2mA 0.5 V VOH Reset Output High ISOURCE=0.6mA 0.8*VCC TD VCC to Reset Delay VCC=VTH to (VTH-100mV) 25 µS ILE Reset Output Leakage 0.5 µA Application Circuit VCC VCC VCC 100k APR3003 RESET GND Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 VCC VCC RESET µ P INPUT APR3001 RESET APR3002 (RESET) GND GND 4 VCC RESET µP INPUT GND www.anpec.com.tw APR3001/2/3 Timing Chart Reset Threshold Reset Threshold Vcc (APR3002) RESET Reset Timeout Period 250ms Vcc to Reset Delay 25us (APR3001/3) RESET Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 5 www.anpec.com.tw APR3001/2/3 Typical Characteristics Maximum Transient Duration vs. Reset Threshold Overdrive VTH - VCC Supply Current vs. Supply Voltage 120 Maximum Transient Duration (us) 2 Supply Current (uA) 1.6 1.2 0.8 0.4 0 0 1 2 3 4 5 generate a reset signal 80 60 40 20 never generate a reset signal 0 10 6 100 1000 Reset Threshold Overdrive VTH - VCC (mV) Supply Voltage (V) Output Source Current vs. Reset High Output Voltage Output Sink Current vs. Reset Low Output Voltage 50 70 Vcc=5V 50 Vcc=4V 40 30 Vcc=2.9V 45 60 Output Sink Current (mA) Output Source Current (mA) 100 Vcc=3V 20 10 40 35 Vcc=2.5V 30 25 Vcc=2V 20 15 Vcc=1.5 10 5 0 0 0 1 2 3 4 5 0 6 Reset High Output Voltage (V) Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 1 2 3 4 5 6 Reset Low Output Voltage (V) 6 www.anpec.com.tw APR3001/2/3 Typical Characteristics Reset Propagation Delay vs. Temperature 60 1.008 Reset Propagation Delay (us) Normalized Reset Threshold (%) Normalized Reset Threshold vs. Temperature 1.006 1.004 1.002 1 0.998 0.996 0.994 50 40 VOD=100mV 30 20 10 0 -40 -20 0 20 40 60 80 100 120 -40 -20 Temperature (°C) 20 40 60 80 100 120 Temperature (°C) Supply Current vs. Temperature Reset Timeout Period vs. Temperature 600 3.5 500 3 Supply Current (uA) Reset Timeout Period (ms) 0 400 300 200 100 2.5 Vcc=5V 2 1.5 Vcc=3V 1 0.5 0 0 -40 -20 0 20 40 60 80 100 120 -40 Temperature (°C) Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 7 -20 0 20 40 60 Temperature (°C) 80 100 120 www.anpec.com.tw APR3001/2/3 Typical Characteristics Power Up Power Down Vcc(2V/div) Vcc(2V/div) RESET(2V/div) RESET(2V/div) Time (50ms/div) Time (200ms/div) Vcc to RESET Delay Vcc(0.5V/div) Vcc=V TH to (VTH-100mV) RESET(2V/div) Time (10us/div) Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 8 www.anpec.com.tw APR3001/2/3 Application Information VCC Transient Rejection V CC The APR3001/2/3 have the function to reject the tranV CC sient glitches from the power line. The Maximum Transient Duration vs. Reset Threshold Overdrive shows RESET at Typical Characteristics.The transient voltage with the duration under the curve will not generate a reset signal, e.g. a transient of 100mV below the reset threshold voltage have the duration more than 35us, it will generate a reset signal. Connect a 0.1uF bypass capacitor to the VCC pin can improve the transient immunity. 100K GND Figure 1. Ensuring RESET Valid to VCC = 0 V +3.3V Reset Output The APR3001/2/3 have 3 output stage versions: APR3001 is an active low push-pull output, when the VCC drops below the reset threshold, the RESET output generates a low signal. APR3002 is an active high push-pull output, when the VCC drops below the reset threshold, the RESET output generates a high signal (see Timing Chart). APR3003 is an active low open drain output, the RESET output must be connected a pull-up resistor to a supply voltage that is lower than 6V, it suits to use in multiple voltage systems (see Figure 2). The APR3001 RESET output is valid until the VCC=1.2V, below 1.2V the IC is shutdown, and +5.0V V CC V CC APR3003 RESET GND 100k RESET 5V INPUT System GND Figure 2. APR3003 Open Drain Output with Multiple Supplies the output becomes a floating state. If it is a trouble, a resistor should be connected from reset output to ground to keep the reset output low (see Figure 1). For The APR3002, a pull-up resistor to VCC is required to keep the valid reset output for VCC below 1.2V. Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 9 www.anpec.com.tw APR3001/2/3 Packaging Information SOT-23 D B 3 E H 2 1 e A L A1 D im A A1 B C D E e H L C M illim e t e rs M in . 1 .0 0 0 .0 0 0 .3 5 0 .1 0 2 .7 0 1 .4 0 In c h e s M ax. 1 .3 0 0 .1 0 0 .5 1 0 .2 5 3 .1 0 1 .8 0 M in . 0 .0 3 9 0 .0 0 0 0 .0 1 4 0 .0 0 4 0 .1 0 6 0 .0 5 5 3 .0 0 0 .0 9 4 0 .0 1 5 1 .9 0 /2 .1 B S C 2 .4 0 0 .3 7 Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 M ax. 0 .0 5 1 0 .0 0 4 0 .0 2 0 0 .0 1 0 0 .1 2 2 0 .0 7 1 0 .0 7 5 /0 .0 8 3 B S C 10 0 .11 8 www.anpec.com.tw APR3001/2/3 Packaging Information SOT-23-5 e1 5 4 E1 1 E 3 2 e b D A2 A a A1 Dim A A1 A2 b D E E1 e e1 L L1 L2 N α L2 L M illimeters M in . 0.95 0.05 0.90 0.30 2.8 2.6 1.5 Inches M ax. 1.45 0.15 1.30 0.50 3.00 3.00 1.70 M in. 0.037 0.002 0.035 0.011 0.110 0.102 0.059 0.55 0.014 0.7 0.020 0.20 BSC 0.5 Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 0.022 0.008 BSC 5 0° M ax. 0.057 0.006 0.051 0.019 0.118 0.118 0.067 0.037BSC 0.074BSC 0.95BSC 1.90BSC 0.35 L1 0.028 5 10° 11 0° 10° www.anpec.com.tw APR3001/2/3 Packaging Information SOT-89 (Reference EIAJ ED-7500A Reg stration SC-62) D D1 a E H 1 2 3 L C B1 B e e1 A a D im A B B1 C D D1 e e1 E H L α M illim eters M in. 1.40 0.40 0.35 0.35 4.40 1.35 Inches M ax. 1.60 0.56 0.48 0.44 4.60 1.83 M in. 0.055 0.016 0.014 0.014 0.173 0.053 1.50 B SC 3.00 B SC 2.29 3.75 0.80 Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 M ax. 0.063 0.022 0.019 0.017 0.181 0.072 0.059 BSC 0.118 B SC 2.60 4.25 1.20 10° 12 0.090 0.148 0.031 0.102 0.167 0.047 10° www.anpec.com.tw APR3001/2/3 Physical Specifications Terminal Material Lead Solderability Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb), 100%Sn Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3. Reflow Condition (IR/Convection or VPR Reflow) tp TP Critical Zone T L to T P Temperature Ram p-up TL tL Tsm ax Tsm in Ram p-down ts Preheat 25 t 25 °C to Peak Tim e Classificatin Reflow Profiles Profile Feature Sn-Pb Eutectic Assembly Large Body Small Body Average ramp-up rate 3°C/second max. (TL to TP) Preheat - Temperature Min (Tsmin) 100°C - Temperature Mix (Tsmax) 150°C - Time (min to max)(ts) 60-120 seconds Tsmax to TL - Ramp-up Rate Tsmax to TL - Temperature(TL) 183°C - Time (tL) 60-150 seconds Peak Temperature(Tp) 225 +0/-5°C 240 +0/-5°C Time within 5°C of actual Peak 10-30 seconds 10-30 seconds Temperature(tp) Ramp-down Rate 6°C/second max. 6 minutes max. Time 25°C to Peak Temperature Pb-Free Assembly Large Body Small Body 3°C/second max. 150°C 200°C 60-180 seconds 3°C/second max 217°C 60-150 seconds 245 +0/-5°C 250 +0/-5°C 10-30 seconds 20-40 seconds 6°C/second max. 8 minutes max. Note: All temperatures refer to topside of the package. Measured on the body surface. Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 13 www.anpec.com.tw APR3001/2/3 Reliability test program Test item SOLDERABILITY HOLT PCT TST ESD Latch-Up Method MIL-STD-883D-2003 MIL-STD-883D-1005.7 JESD-22-B,A102 MIL-STD-883D-1011.9 MIL-STD-883D-3015.7 JESD 78 Description 245°C, 5 SEC 1000 Hrs Bias @125°C 168 Hrs, 100%RH, 121°C -65°C~150°C, 200 Cycles VHBM > 2KV, VMM > 200V 10ms, 1tr > 100mA Carrier Tape & Reel Dimensions t D P Po E P1 Bo F W Ao D1 Ko T2 J C A B T1 Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 14 www.anpec.com.tw APR3001/2/3 Carrier Tape & Reel Dimensions A p p lic a t io n S O T -2 3 A p p lic a t io n S O T -2 3 -5 A p p lic a t io n S O T -8 9 A B C J T1 178±1 6 0 ± 1 .0 1 2 .0 F D D1 P E 1 .4 W 8 .0 + 0 .3 - 0 .3 Po P1 4 .0 1 .7 5 Ao Bo Ko t 3 .5 ± 0 .0 5 1 .5 + 0 .1 φ 0 .1 M IN 4 .0 A B C J 2 .0 ± 0 .0 5 3 .1 3 .0 1 .3 0 .2 ± 0 .0 3 T1 T2 W P 178 ±1 7 2 ± 1 .0 1 3 .0 + 0 .2 E 2 .5 ± 0 .1 5 8 .4 ± 2 1 .5 ± 0 .3 8 .0 ± 0 .3 4 ± 0 .1 1 .7 5 ± 0 .1 F D D1 Po P1 Ao Bo Ko t 3 .5 ± 0 .0 5 A 1 .5 ± 0 .1 1 .5 ± 0 .1 4 .0 ± 0 .1 3 .2 ± 0 .1 1 .4 ± 0 .1 0 .2 ± 0 .0 3 3 B C J T1 T2 P E 70 ± 2 1 3 .5 ± 0 .1 5 3 ± 0 .1 5 14 ± 2 1 .3 ± 0 .3 W 1 2 + 0 .3 1 2 - 0 .1 178 ±1 8 ± 0 .1 1 .7 5 ± 0 .1 Ko t 2 .5 ± 0 .1 5 9 .0 ± 0 .5 T2 2 .0 ± 0 .1 3 .1 5 ± 0 .1 F D D1 Po P1 Ao Bo 5 .5 ± 0 .0 5 1 .5 ± 0 .1 1 .5 ± 0 .1 4 .0 ± 0 .1 2 .0 ± 0 .1 4 .8 ± 0 .1 4 .5 ± 0 .1 1 .8 0 ± 0 .1 0 .3 ± 0 .0 1 3 (mm) Cover Tape Dimensions Application SOT- 23 SOT- 23-5 SOT- 89 Carrier Width 8 8 12 Cover Tape Width 5.3 5.3 9.3 Devices Per Reel 3000 3000 1000 Customer Service Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369 Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 15 www.anpec.com.tw