NICHIA NSSM124 Specifications for full color led Datasheet

NICHIA STS-DA1-2472A <Cat.No.120522>
NICHIA CORPORATION
SPECIFICATIONS FOR FULL COLOR LED
NSSM124T
● Pb-free Reflow Soldering Application
● RoHS Compliant
● RGB Sorted (RGB die lit separately.)
NICHIA STS-DA1-2472A <Cat.No.120522>
SPECIFICATIONS
(1) Absolute Maximum Ratings
Item
Absolute Maximum Rating
Symbol
Blue
Green
Unit
Red
Forward Current
IF
25
35
50
mA
Pulse Forward Current
IFP
80
110
150
mA
Reverse Voltage
VR
Power Dissipation
5
PD
88.7
V
124
127
mW
Total Power Dissipation
PTOT
150
mW
Operating Temperature
Topr
-30~85
°C
Storage Temperature
Tstg
Junction Temperature
TJ
-40~100
100
°C
100
100
°C
* Absolute Maximum Ratings at TA=25°C.
* IFP conditions with pulse width ≤10ms and duty cycle ≤10%.
* The absolute maximum Power Dissipation per die.
* The absolute maximum Power Dissipation in total per package.
(2) Initial Electrical/Optical Characteristics
Item
Symbol
Condition
Typ
Unit
Blue
Green
Red
3.2
3.2
2.2
V
-
-
-
µA
450
2100
750
mcd
0.133
0.189
0.700
0.075
0.718
0.299
B IF=20mA
Forward Voltage
VF
G IF=20mA
R IF=20mA
B VR=5V
Reverse Current
IR
G VR=5V
R VR=5V
B IF=20mA
Luminous Intensity
IV
G IF=20mA
R IF=20mA
B IF=20mA
x
Chromaticity Coordinate
y
-
G IF=20mA
R IF=20mA
-
* Characteristics at TA=25°C.
* Luminous Intensity value as per CIE 127:2007 standard.
* Chromaticity Coordinates as per CIE 1931 Chromaticity Chart.
1
NICHIA STS-DA1-2472A <Cat.No.120522>
RANKS
Item
Blue
Green
Red
Unit
Min
Max
Min
Max
Min
Max
Forward Voltage
2.80
3.55
2.75
3.55
1.80
2.55
V
Reverse Current
-
50
-
50
-
50
µA
300
600
1400
2800
500
1000
mcd
Luminous Intensity
Color Rank
Blue
Rank W
x
0.139
0.129
0.113
0.134
0.145
0.152
y
0.035
0.050
0.080
0.105
0.072
0.056
x
0.136
0.190
0.219
0.250
0.220
0.176
y
0.739
0.628
0.637
0.638
0.745
0.750
x
0.674
0.648
0.677
0.708
y
0.296
0.323
0.323
0.292
Green
Rank G0d
Red
Rank R
* Ranking at TA=25°C.
* Tolerance of measurements of the Forward Voltage is ±0.05V.
* Tolerance of measurements of the Luminous Intensity is ±10%.
* Tolerance of measurements of the Chromaticity Coordinate is ±0.01.
2
NICHIA STS-DA1-2472A <Cat.No.120522>
CHROMATICITY DIAGRAM
0.9
520
530
0.8
540
510
0.7
550
G0d
560
0.6
570
500
0.5
y
580
590
0.4
600
0.3
R
490
610
620
630
0.2
480
0.1
W
470
0.0
0.0
460
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
x
3
NICHIA STS-DA1-2472A <Cat.No.120522>
OUTLINE DIMENSIONS
* 本製品はRoHS指令に適合しております。
This product complies with RoHS Directive.
管理番号 No.
NSSM124
STS-DA7-0041B
(単位 Unit: mm, 公差 Tolerance:
(単位 Unit:±0.2)
mm)
3.3
2.8
Pin-1 Mark
(2.25)
2
5
3
4
項目 Item
内容 Description
パッケージ材質
Package Materials
耐熱性ポリマー
Heat-resistant Polymer
0.5
封止樹脂材質
Encapsulating Resin
Materials
エポキシ樹脂 （拡散剤入り）
Epoxy Resin (with diffuser)
0.5
0.1
0.75 ± 0.1
Red
3
6
(2.55)
1
電極材質
Electrodes Materials
銅合金+銀メッキ
Ag-plated Copper Alloy
0.5
Green
(0.7)(0.7)
Blue
質量
Weight
0.014g (TYP)
2.1
(0.34)
* Redダイ、Blueダイ、Greenダイは カソード側に実装されています。
The Red, Blue and Green die are connected to the Cathode side.
1
6
Blue
2
5
Green
3
4
Red
4
NICHIA STS-DA1-2472A <Cat.No.120522>
SOLDERING
• Recommended Reflow Soldering Condition(Lead-free Solder)
1 to 5°C per sec
260°C Max
10sec Max
Pre-heat
180 to 200°C
• Recommended Hand Soldering Condition
Temperature
350°C Max
Soldering Time
3sec Max
60sec Max
Above 220°C
120sec Max
● Recommended Soldering Pad Pattern
4.5
2.2
1.15
0.85
3.05
0.75
0.85
1.15
(単位 Unit: mm)
* This LED is designed to be reflow soldered on to a PCB. If dip soldered, Nichia cannot guarantee its reliability.
* Reflow soldering must not be performed more than twice. Hand soldering must not be performed more than once.
* Avoid rapid cooling. Ramp down the temperature gradually from the peak temperature.
* Nitrogen reflow soldering is recommended. Air flow soldering conditions can cause optical degradation,
caused by heat and/or atmosphere.
* Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable,
a double-head soldering iron should be used.
It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
* When soldering, do not apply stress to the LED while the LED is hot.
* This product can differ in optical characteristics depending on the number of reflow cycles.
In a single display, only LEDs with same number of reflow cycles should be used regardless of the application type,
such as rental and/or permanent installations.
5
NICHIA STS-DA1-2472A <Cat.No.120522>
TAPE AND REEL DIMENSIONS
3.5±0.05
Pin-1 Mark
0.2±0.05
Nxxx124x
STS-DA7-0042
(単位 Unit: mm)
3.5±0.1
2±0.05
1.75±0.1
4±0.1
Φ 1.5+0.1
-0
管理番号 No.
8+0.3
-0.1
テーピング部 Tape
1.05±0.1
4±0.1
Φ
1+0.2
-0
3.1±0.1
エンボスキャリアテープ
Embossed Carrier Tape
トレーラ部/リーダ部 Trailer and Leader
トップカバーテープ
Top Cover Tape
引き出し方向
Feed
Direction
トレーラ部MIN 160mm（空部）
Trailer 160 mm MIN (Empty Pockets)
LED装着部
Loaded Pockets
引き出し部MIN 100mm（空部）
Leader with Top Cover Tape
100 mm MIN (Empty Pocket)
リーダ部MIN 400mm
Leader without Top Cover Tape 400 mm MIN
リール部 Reel
180+0
-3
11.4±1
9±0.3
* 数量は1リールにつき 3500個入りです。
Quantity per reel = 3500 pcs
Φ
* JIS C 0806電子部品テーピングに準拠しています。
The tape packing method complies with JIS C 0806
(Packaging of Electronic Components on Continuous Tapes).
±
21
±0.2
ラベル
Label
Φ
13 ±
0.
2
f 13
.8
Φ 60+1
-0
8
0.
f2
1 ±0
6
NICHIA STS-DA1-2472A <Cat.No.120522>
PACKAGING - TAPE & REEL
シリカゲルとともにリールをアルミ防湿袋に入れ、熱シールにより封をします。
Reels are shipped with desiccants in heat-sealed moisture-proof bags.
管理番号 No.
Nxxxxxxx
STS-DA7-0006B
ラベル Label
リール
Reel
シリカゲル
Desiccants
XXXX LED
TYPE Nxxxxxxx
*******
LOT YMxxxx-RRR
QTY.
PCS
RoHS
NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
熱シール
Seal
アルミ防湿袋
Moisture-proof Bag
アルミ防湿袋を並べて入れ、ダンボールで仕切ります。
Moisture-proof bags are packed in cardboard boxes
with corrugated partitions.
ラベル Label
XXXX LED
TYPE Nxxxxxxx
*******
RANK RRR
QTY.
PCS
RoHS
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
Nichia
LED
* 客先型名を*******で示します。
客先型名が設定されていない場合は空白です。
******* is the customer part number.
If not provided, it is not indicated on the label.
* ロット表記方法についてはロット番号の項を
参照して下さい。
For details, see "LOT NUMBERING SCHEME"
in this document.
* ランク分けがない場合はランク表記はありません。
The label does not have the RANK field for
un-ranked products.
* 本製品はテーピングしたのち、輸送の衝撃から保護するためダンボールで梱包します。
Products shipped on tape and reel are packed in a moisture-proof bag.
They are shipped in cardboard boxes to protect them from external forces during transportation.
* 取り扱いに際して、落下させたり、強い衝撃を与えたりしますと、製品を損傷させる原因になりますので注意して下さい。
Do not drop or shock the box. It may damage the products.
* ダンボールには防水加工がされておりませんので、梱包箱が水に濡れないよう注意して下さい。
Do not expose to water, the box is not water-resistant.
* 輸送、運搬に際して弊社よりの梱包状態あるいは同等の梱包を行って下さい。
Using an original packaging material or equivalent in transit is recommended.
7
NICHIA STS-DA1-2472A <Cat.No.120522>
LOT NUMBERING SCHEME
Lot Number is presented by using the following alphanumeric code.
YMxxxx - RRR
Y - Year
Year
Y
2009
9
2010
A
2011
B
2012
C
2013
D
2014
E
M - Month
Month
M
Month
M
1
1
7
7
2
2
8
8
3
3
9
9
4
4
10
A
5
5
11
B
6
6
12
C
xxxx-Nichia's Product Number
RRR-Rank
* The label does not have the RANK field for un-ranked products.
8
NICHIA STS-DA1-2472A <Cat.No.120522>
DERATING CHARACTERISTICS
NSSM124x
管理番号 No. STS-DA7-0043B
周囲温度-許容損失特性
周囲温度-全許容損失特性
Ambient Temperature vs
Total Power Dissipation
BLUE
GREEN
RED
200
200
全許容損失
250
150
(32, 124)GREEN
(38, 127)RED
100
(47, 88.7)BLUE
(85, 30.0)RED
50
(85, 27.0)GREEN
(85, 25.0)BLUE
20
40
60
(40, 150)
150
100
50
(85, 37.5)
0
0
0
**
Derating2
250
Total Power Dissipation(mW)
許容損失
Power Dissipation(mW)
*
Ambient Temperature vs
Power Dissipation
Derating1
80
100
120
0
20
40
60
80
周囲温度
周囲温度
Ambient Temperature(°C)
Ambient Temperature(°C)
デューティー比-許容順電流特性
Duty Ratio vs
Allowable Forward Current
100
120
T A=25°C
Duty
BLUE
GREEN
RED
許容順電流
Allowable Forward Current(mA)
1000
150
110
100
80
50
35
25
10
1
10
100
デューティー比
Duty Ratio(%)
*
多色点灯の際も、1素子当たりの値はこの定格内におさめて下さい。
The graph shows the maximum allowable power dissipation for a LED die of each color.
**
2素子以上点灯の際は、トータル値を定格内におさめて下さい。
The graph shows the maximum allowable total power dissipation for a LED package.
9
NICHIA STS-DA1-2472A <Cat.No.120522>
OPTICAL CHARACTERISTICS
* 本特性は参考です。
All characteristics shown are for reference only and are not guaranteed.
発光スペクトル
Spectrum
NSSM124
STS-DA7-0044
管理番号 No.
相対発光強度
Relative Emission Intensity (a.u.)
Spectrum
1.0
TA = 25°C
BLUE ( IF = 20 mA)
GREEN ( IF = 20 mA)
RED ( I F = 20 mA)
0.8
0.6
0.4
0.2
0.0
400
450
500
550
600
650
700
波長
Wavelength (nm)
Directivit y1
指向特性
Directivity
X-X
- 20°
-10°
0°
10°
20°
放射角度
Radiation Angle
TA = 25°C
30°
-30°
BLUE ( I FP = 20 mA)
GREEN ( IFP = 20 mA)
RED ( I FP = 20 mA)
40°
-40°
50°
-50°
-60°
Y (9 0°)
60°
-70°
-90°
X
(9 0°)
(-9 0°)
Y (-9 0°)
80°
-80°
90°
1
0.5
0
相対光度
Relative Luminosity
0.5
1
(a.u.)
Directivity2
Y-Y
-20°
-10°
0°
10°
20°
Radiation Angle
-30°
放射角度
X
70°
-40°
BLUE ( I FP = 20 mA)
GREEN ( IFP = 20 mA)
RED ( I FP = 20 mA)
40°
-50°
50°
-60°
60°
-70°
70°
-80°
-90°
1
TA = 25°C
30°
80°
0.5
0
相対光度
Relative Luminosity
0.5
1
90°
(a.u.)
10
NICHIA STS-DA1-2472A <Cat.No.120522>
FORWARD CURRENT CHARACTERISTICS / TEMPERATURE CHARACTERISTICS
NSSM124x
管理番号 No. STS-DA7-0045A
* 本特性は参考です。
All characteristics shown are for reference only and are not guaranteed.
順電圧-順電流特性
Forward Voltage vs
Forward Current
T A=25°C
VfIf
BLUE
GREEN
RED
周囲温度-順電圧特性
Ambient Temperature vs
Forward Voltage
TaVf
BLUE
IFP=20mA
GREEN IFP=20mA
IFP=20mA
RED
5.0
1000
150
110
100
80
順電圧
Forward Voltage(V)
順電流
Forward Current(mA)
4.5
20
10
4.0
3.5
3.0
2.5
2.0
1
1.5
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
-60 -40 -20
順電圧
Forward Voltage(V)
20
40
60
80
100 120
周囲温度
Ambient Temperature(°C)
T A=25°C
順電流-相対光度特性
Forward Current vs
Relative Luminosity
0
周囲温度-相対光度特性
BLUE
GREEN
RED
IfIv
Ambient Temperature vs
Relative Luminosity
IFP=20mA
GREEN IFP=20mA
IFP=20mA
RED
TaIv BLUE
1.4
7
相対光度
Relative Luminosity(a.u.)
相対光度
Relative Luminosity(a.u.)
6
5
4
3
2
1.2
1.0
0.8
1
0
0.6
0
50
100
150
順電流
Forward Current(mA)
200
-60 -40 -20
0
20
40
60
80
100 120
周囲温度
Ambient Temperature(°C)
11
NICHIA STS-DA1-2472A <Cat.No.120522>
RELIABILITY
(1) Tests and Results
Reference
Test
Standard
Resistance to
Test
Test Conditions
Duration
JEITA ED-4701
Tsld=260°C, 10sec, 2reflows,
300 301
Precondition: 30°C, 70%RH, 168hr
JEITA ED-4701
-40°C(30min)~25°C(5min)~
100 105
100°C(30min)~25°C(5min)
Moisture Resistance
JEITA ED-4701
25°C~65°C~-10°C, 90%RH,
(Cyclic)
200 203
24hr per cycle
High Temperature
JEITA ED-4701
Storage
200 201
Temperature Humidity
JEITA ED-4701
Storage
100 103
Low Temperature
JEITA ED-4701
Storage
200 202
Soldering Heat
(Reflow Soldering)
Temperature Cycle
Failure
Criteria
#
Units
Failed/Tested
#1
0/50
100cycles
#1
0/50
10cycles
#1
0/50
TA=100°C
500hours
#1
0/50
TA=60°C, RH=90%
500hours
#1
0/50
TA=-40°C
500hours
#1
0/50
500hours
#1
0/50
500hours
#1
0/50
500hours
#1
0/50
B IF=9mA
Room Temperature
TA=25°C
Operating Life
G IF=14mA
R IF=18mA
B IF=5mA
Temperature Humidity
60°C, RH=90%
Operating Life
G IF=11mA
R IF=11mA
B IF=9mA
Low Temperature
TA=-30°C
Operating Life
G IF=14mA
R IF=18mA
NOTES:
Measurements are performed after allowing the LEDs to return to room temperature.
(2) Failure Criteria (Value for one LED device (Single color).)
Criteria #
Items
Conditions
Failure Criteria
B IF=20mA
Forward Voltage(VF)
G IF=20mA
>U.S.L.×1.1
R IF=20mA
B IF=20mA
#1
Luminous Intensity(IV)
G IF=20mA
<L.S.L×0.7
R IF=20mA
B VR=5V
Reverse Current(IR)
G VR=5V
>U.S.L.×2.0
R VR=5V
U.S.L. : Upper Specification Limit
L.S.L. : Lower Specification Limit
12
NICHIA STS-DA1-2472A <Cat.No.120522>
CAUTIONS
(1) Storage
Conditions
Storage
Temperature
Humidity
Time
Before Opening Aluminum Bag
≤30°C
≤90%RH
Within 1 Year from Delivery Date
After Opening Aluminum Bag
≤30°C
≤70%RH
≤168hours
65±5°C
-
≥24hours
Baking
● Product complies with JEDEC MSL 3 or equivalent. See IPC/JEDEC STD-020 for moisture-sensitivity details.
● Absorbed moisture in LED packages can vaporize and expand during soldering, which can cause interface delamination
and result in optical performance degradation. Products are packed in moisture-proof aluminum bags
to minimize moisture absorption during transportation and storage.
Included silica gel desiccants change from blue to red if moisture had penetrated bags.
● After opening the moisture-proof aluminum bag, the products should go through the soldering process
within the range of the conditions stated above. Unused remaining LEDs should be stored with silica gel desiccants
in a hermetically sealed container, preferably the original moisture-proof bags for storage.
● After the “Period After Opening” storage time has been exceeded or silica gel desiccants are no longer blue,
the products should be baked. Baking should only be done once.
● The leads or electrode pads (anode and cathode) of the product are plated with silver. Exposure to a corrosive environment
might cause the silver plated the leads or electrode pads to tarnish, and thus leading to difficulties in soldering.
If unused LEDs remain, they must be stored in a hermetically sealed container.
Nichia recommends using the original moisture-proof bag for storage.
● Do not use sulfur-containing materials in commercial products. Some materials, such as seals and adhesives, may contain sulfur.
The extremely corroded or contaminated plating of LEDs might cause an open circuit. Silicone rubber is recommended
as a material for seals. Bear in mind, the use of silicones may lead to silicone contamination of electrical contacts
inside the products, caused by low molecular weight volatile siloxane.
● To prevent water condensation, please avoid large temperature and humidity fluctuations for the storage conditions.
(2) Directions for Use
● In designing a circuit, the current through each LED die must not exceed the Absolute Maximum Rating current
specified for each die.
It is recommended that each LED die is driven at a constant current.
● When having the two or more dice within this product on at the same time, the total power dissipation for the LED package
must be within the absolute maximum value specified in this specification.
● LEDs should be operated in forward bias. Driving circuits must not subject LEDs to either forward or reverse voltage while off.
Continuous reverse voltage can cause migration and LED damage.
● For stabilizing the LED characteristics, it is recommended to operate at greater than 10% nominal current.
● Care must be taken to ensure that the reverse voltage will not exceed the Absolute Maximum Rating
when using the LEDs with matrix drive.
● For outdoor use, necessary measures should be taken to prevent water, moisture and salt air damage.
(3) Handling Precautions
● Do not handle LEDs with bare hands, it may contaminate the LED surface and affect optical characteristics.
In the worst case, catastrophic failure from excess pressure through wire-bond breaks and package damage may result.
● When handling the product with tweezers, be careful not to apply excessive force to the resin.
Otherwise, The resin can be cut, chipped, delaminate or deformed, causing wire-bond breaks and catastrophic failures.
● Dropping the product may cause damage.
● Do not stack assembled PCBs together. Failure to comply can cause the resin portion of the product to be cut, chipped,
delaminated and/or deformed. It may cause wire to break, leading to catastrophic failures.
13
NICHIA STS-DA1-2472A <Cat.No.120522>
(4) Design Consideration
● PCB warpage after mounting the products onto a PCB can cause the package to break.
The LED should be placed in a way to minimize the stress on the LEDs due to PCB bow and twist.
● The position and orientation of the LEDs affect how much mechanical stress is exerted on the LEDs placed near the score lines.
The LED should be placed in a way to minimize the stress on the LEDs due to board flexing.
● Board separation must be performed using special jigs, not using hands.
(5) Electrostatic Discharge (ESD)
● The products are sensitive to static electricity or surge voltage. ESD can damage a die and its reliability.
When handling the products, the following measures against electrostatic discharge are strongly recommended:
Eliminating the charge
Grounded wriststrap, ESD footwear, clothes, and floors
Grounded workstation equipment and tools
ESD table/shelf mat made of conductive materials
● Proper grounding is required for all devices, equipment, and machinery used in product assembly.
Surge protection should be considered when designing of commercial products.
● If tools or equipment contain insulating materials such as glass or plastic,
the following measures against electrostatic discharge are strongly recommended:
Dissipating static charge with conductive materials
Preventing charge generation with moisture
Neutralizing the charge with ionizers
● The customer is advised to check if the LEDs are damaged by ESD
when performing the characteristics inspection of the LEDs in the application.
Damage can be detected with a forward voltage measurement or a light-up test at low current (≤1mA).
● LEDs with ESD-damaged dice (i.e. other than red) may have an increased leakage current, current flow at a low voltage,
or no longer illuminate at a low current.
Failure Criteria: VF<2.0V at IF=0.5mA
(6) Thermal Management
● Proper thermal management is an important when designing products with LEDs. LED die temperature is affected
by PCB thermal resistance and LED spacing on the board. Please design products in a way that the LED die temperature
does not exceed the maximum Junction Temperature (TJ).
● Drive current should be determined for the surrounding ambient temperature (TA) to dissipate the heat from the product.
(7) Cleaning
● If required, isopropyl alcohol (IPA) should be used. Other solvents may cause premature failure to the LEDs
due to the damage to the resin portion. The effects of such solvents should be verified prior to use.
In addition, the use of CFCs such as Freon is heavily regulated.
● Ultrasonic cleaning is not recommended since it may have adverse effects on the LEDs
depending on the ultrasonic power and how LED is assembled.
If ultrasonic cleaning must be used, the customer is advised to make sure the LEDs will not be damaged prior to cleaning.
(8) Eye Safety
● In 2006, the International Electrical Commission (IEC) published IEC 62471:2006 Photobiological safety of lamps
and lamp systems, which added LEDs in its scope.
On the other hand, the IEC 60825-1:2007 laser safety standard removed LEDs from its scope.
However, please be advised that some countries and regions have adopted standards
based on the IEC laser safety standard IEC 60825-1:20112001, which still includes LEDs in its scope.
Most of Nichia's LEDs can be classified as belonging into either the Exempt Group or Risk Group 1.
High-power LEDs, that emit light containing blue wavelengths, may be classified as Risk Group 2.
Please proceed with caution when viewing directly any LEDs driven at high current, or viewing LEDs
with optical instruments which may greatly increase the damages to your eyes.
● Viewing a flashing light may cause eye discomfort. When incorporating the LED into your product,
please be careful to avoid adverse effects on the human body caused by light stimulation.
14
NICHIA STS-DA1-2472A <Cat.No.120522>
(9) Others
● The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment,
communications equipment, measurement instruments and household appliances).
Consult Nichia's sales staff in advance for information on the applications in which exceptional quality
and reliability are required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or
health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control system, automobiles,
traffic control equipment, life support systems and safety devices).
● The customer shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent
from Nichia. When defective LEDs are found, the customer shall inform Nichia directly before disassembling or analysis.
● Both the customers and Nichia will agree on official specifications of supplied products before a customer's volume production.
● Specifications and appearance subject to change for improvement without notice.
15