Artesyn BXB100-48S12FLTJ Total power: 66 - 100 w Datasheet

POWER
BXB Series
66 - 100 Watts
Data Sheet
Total Power:66 - 100 W
Input Voltage:18 - 36 V
36 - 75 V
# of Outputs: Single
SPECIAL FEATURES
ƒƒ Industry standard footprint
ƒƒ High power density (36.5 W/in3)
ƒƒ MTBF >1.4 million hours (Bellcore 332)
ƒƒ Input voltage to ETS300-132-2
ƒƒ Adjustable output voltage
ƒƒ No minimum load required
ƒƒ Separate case ground pin
ƒƒ Undervoltage lockout (UVLO)
ƒƒ UL, VDE and CSA safety approvals
ƒƒ Two year warranty
SAFETY
ƒƒ VDE0805/EN60950/IEC950
ƒƒ UL1950
ƒƒ CSA C22.2 No. 950
Electric
Input
Input voltage range
Input current (max.) (See Note 4)
24 Vin nominal
48 Vin nominal
No load
Remote OFF
48 V models
18 - 36 Vdc
36 - 75 Vdc
100 mA max.
20 mA max.
4 A max. @ Io max.
and Vin = 0 - 75 V
Input reflected ripple
(See Note 6)
5 mA pk-pk
Active low remote ON/OFF
(See Note 7)
Logic compatibility
ON
OFF
Open collector ref to -input
1.2 Vdc max.
Open circuit
Undervoltage lockout
24 Vin: power up
24 Vin: power down
48 Vin: power up
48 Vin: power down
Power up
Remote ON/OFF
17 V
16 V
34 V
32.5 V
20 ms
20 ms
Input current
Start-up time
(See Note 8)
Output
Voltage adjustability
60% to 110%
Setpoint accuracy
±1.0%
Line regulation
Low line to high line
±0.5%
Load regulation
Full load to min. load
±0.10%
Minimum load
0%
Overshoot
At turn on and turn off
Undershoot
None
Ripple and noise
5 Hz - 20 MHz (See Note 1)
3.3 V and 5 V
2 V and 15 V
Temperature co-efficient
±0.01% / °C
Transient response (See Note 2)
±2.0% max. deviation; 170 µs recovery to within ±1.0%
Remote sense
0.5 Vds transmission line drop compensation
None
75 mV pk-pk, 20 mV rms
100 mV pk-pk, 30 mV rms
BXB100 Series Data Sheet
General Specifications
Environmental Specifications
Efficiency
(See Efficiency Table)
Thermal performance
Insulation voltage
Input/Case
Input/Output
Output/Case
1500 Vdc
1500 Vdc
1500 Vdc
Operating case temperature
Non-operating temperature
-40 °C to +85 °C
-55 °C to +125 °C
Altitude
Operating
Non-operating
10,000 feet max.
40,000 feet max.
Switching frequency
Fixed
500 kHz typ.
Vibration
5 - 500 Hz
2.4 G rms (approx.)
Approvals and
standards (See Note 5)
VDE0805, EN60950, IEC950
UL1950, CSA C22.2 No. 950
Case material
Aluminum baseplate with plastic case
Material flammability
UL94V-0
Weight
110 g (3.88 oz)
MTBF
Bellcore 332
MIL-HDBK-217F @
40 °C C, 100% loaded
Protection
1,400,000 hours
580,000 hours min.
Continuous, automatic recovery
Overvoltage
Non-latching
Undervoltage
Non-latching
Thermal
100 °C baseplate, automatic recovery
Telecom Specifications
EMC Characteristics
Conducted emissions
(See Note 3)
Short-circuit
EN55022 (See Note 3)
FCC part 15
EN55022, CISPR22
Central office
interface A
Level A
Level A
Level A
ETS300-132-2
Ordering Information
Model
Number
Output Power
(Max.)
Input
Voltage
OVP
BXB100-24S12FLTJ
100 W
18 - 36 Vdc
14.5 Vdc
BXB100-48S05FLTJ
100 W
36 - 75 Vdc
BXB100-48S12FLTJ
100 W
36 - 75 Vdc
Regulation
Output Voltage
Output Current
(Min)
Output Current
(Max)
Efficiency
(Typical)
Line
Load
12 V
0A
8.33 A
85%
±0.05%
±0.1%
6.5 Vdc
5V
0A
20 A
83%
±0.05%
±0.1%
14.5 Vdc
12 V
0A
8.33 A
86%
±0.05%
±0.1%
Notes:
1. Measured with 10 μF tantalum capacitor and 1 μF ceramic capacitor across output.
2. di/dt = 0.1 A/1 μs, Vin = 48 Vdc, Tc = 25 °C, load change = 0.5 lo max. to 0.75 lo max. and 0.75
Io max. to 0.5 Io max.
3. Units should be characterised within systems. External components required.
4. Input fusing is recommended based on surge current and maximum input current.
External Output Trimming
Output can be externally trimmed by using the method shown.
8
5. This product is only for inclusion by professional installers within other equipment and must not
be operated as a stand alone product.
6. Simulated source impedance of 12 μH. 12 μH inductor in series with +Vin.
TRIM
UP
7. Active high remote on/off option is available (standard product is active low), designate with the
suffix ‘FHT’ e.g. BXB100-48S05FHTJ. Consult factory for further details and options.
8. Start-up into resistive load.
9 . “J” suffix designation for RoHS 6/6.
7
TRIM
DOWN
6
RT1
OR
RT2
BXB100 Series Data Sheet
Mechanical Dimensions
VIEW SHOWN
PIN SIDE UP
1.90
(48.26)
VI (-)
0.400 (10.16)
2.000 (50.80)
2.40 (60.96)
Max.
1.400 (35.56)
VI(+)
Vo(+)
ON/OFF
1.400 (35.56)
0.700 (17.77)
0.400 (10.16)
1.000 (25.40)
+SEN TRIM -SEN
CASE
1.000 (25.40)
0.190 (4.83) 0.010 (0.25)
Vo (-)
0.500 (12.69) 0.010 (0.25)
0.200 (5.08) Min.
Length for all Input
and Output Pins
7 x Ø.040 (1.02) 0.002 (0.05)
0.190 (4.83) 0.010 (0.25)
2.28 (57.91) Max.
2 x Ø.080 (2.03) 0.002 (0.05)
0.500 (12.70)
4 x M3 x 0.5 Through
ALL DIMENSIONS IN INCHES (mm)
Tolerance : x.xx 0.02in. (0.51mm)
x.xxx 0.010in. (0.254mm)
Pin Connections
Pin
Function
1
+Vin
2
Remote ON/OFF
3
Case
4
-Vin
5
-Vout
6
-Sense
7
8
9
Trim
+Sense
+Vout
WORLDWIDE OFFICES
Americas
Europe (UK)
Asia (HK)
2900 S.Diablo Way
Tempe, AZ 85282
USA
+1 888 412 7832
Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX
United Kingdom
+44 (0) 1384 842 211
14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon
Hong Kong
+852 2176 3333
While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn
Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use
of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn
Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc.
All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective
owners. © 2014 Artesyn Embedded Technologies, Inc.
www.artesyn.com
For more information: www.artesyn.com/power
For support: [email protected]
BXB100 08Jul2015
Similar pages