S2AA-S2MA 1.5AMP.Surface Mount Rectifiers SMA/DO-214AC Features For surface mounted application Glass passivated junction chip. Low forward voltage drop High current capability Easy pick and place High surge current capability Plastic material used carries Underwriters Laboratory Classification 94V-0 High temperature soldering: o 260 C / 10 seconds at terminals Mechanical Data Case: Molded plastic Terminals: Pure tin plated, lead free. Polarity: Indicated by cathode band Packaging: 12mm tape Weight: 0.064 gram Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Symbol S2AA S2BA S2DA S2GA S2JA S2KA S2MA Units Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current @T L =100 oC Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 1.5A Maximum DC Reverse Current @T A =25 oC at Rated DC Blocking Voltage @ T A=125 oC Typical Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Typical Thermal resistance (Note 3) Operating Temperature Range V RRM V RMS V DC 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 I(AV) 1.5 A IFSM 50 A VF 1.1 V IR 5.0 125 1.5 30 16 53 -55 to +150 -55 to +150 uA uA uS pF Trr Cj R θJL R θJA TJ Storage Temperature Range T STG 1. Reverse Recovery Test Conditions: I F=0.5A, IR=1.0A, IRR=0.25A Notes: 2. Measured at 1 MHz and Applied V R=4.0 Volts 3. Measured on P.C. Board with 0.2” x 0.2” (5.0 mm x 5.0mm) Copper Pad Areas. http://www.luguang.cn V V V mail:[email protected] o C/W o o C C S2AA-S2MA 1.5AMP.Surface Mount Rectifiers RATINGS AND CHARACTERISTIC CURVES (S2AA THRU S2MA) FIG.2- TYPICAL REVERSE CHARACTERISTICS FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 10 1.5 1.0 SINGLE PHASE HALF SIZE WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 5.0mm2 PAD AREAS 0.5 0 50 60 70 80 90 100 110 120 o LEAD TEMPERATURE. ( C) 130 140 Tj=125 0C INSTANTANEOUS REVERSE CURRENT. ( A) AVERAGE FORWARD CURRENT. (A) 2.0 150 155 FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT Tj=100 0C 1 0.1 Tj=25 0C 8.3ms Single Half Sine Wave JEDEC Method 40 0.01 0 20 FIG.5- TYPICAL FORWARD CHARACTERISTICS 10 10 0 10 NUMBER OF CYCLES AT 60Hz 1 100 FIG.4- TYPICAL JUNCTION CAPACITANCE 100 60 JUNCTION CAPACITANCE.(pF) 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 30 INSTANTANEOUS FORWARD CURRENT. (A) PEAK FORWARD SURGE CURRENT. (A) 50 40 20 10 6 4 Tj=25 0C f=1.0MHz Vsig=50mVp-p 2 1 0.1 0.2 0.4 1 2 4 10 20 40 1 0.1 0 Tj=25 C PULSE WIDTH-300 S 2% DUTY CYCLE 0.01 0.4 100 0.6 0.8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE. (V) REVERSE VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 0 -0.25A (+) -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm Version: C08 http://www.luguang.cn mail:[email protected]