Product Folder Sample & Buy Technical Documents Support & Community Tools & Software DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 DLP9500 DLP® 0.95 1080p 2x LVDS Type A DMD 1 Features 3 Description • The DLP9500 1080p chipset is part of the DLP® Discovery™ 4100 platform, which enables high resolution and high performance spatial light modulation. The DLP9500 is the digital micromirror device (DMD) fundamental to the 0.95 1080p chipset. The DLP Discovery 4100 platform also provides the highest level of individual micromirror control with the option for random row addressing. Combined with a hermetic package, the unique capability and value offered by DLP9500 makes it well suited to support a wide variety of industrial, medical, and advanced display applications. 1 • • • • • 0.95-Inch Diagonal Micromirror Array – 1920 × 1080 Array of Aluminum, MicrometerSized Mirrors (1080p Resolution) – 10.8-µm Micromirror Pitch – ±12° Micromirror Tilt Angle (Relative to Flat State) – Designed for Corner Illumination Designed for Use With Visible Light (400 to 700 nm): – Window Transmission 97% (Single Pass, Through Two Window Surfaces) – Micromirror Reflectivity 88% – Array Diffraction Efficiency 86% – Array Fill Factor 92% Four 16-Bit, Low-Voltage Differential Signaling (LVDS), Double Data Rate (DDR) Input Data Buses Up to 400-MHz Input Data Clock Rate 42.2-mm × 42.2-mm × 7-mm Package Footprint Hermetic Package 2 Applications • • • Industrial: – Digital Imaging Lithography – Laser Marking – LCD and OLED Repair – Computer-to-Plate Printers – SLA 3D Printers – 3D Scanners for Machine Vision and Factory Automation – Flat Panel Lithography Medical: – Phototherapy Devices – Ophthalmology – Direct Manufacturing – Hyperspectral Imaging – 3D Biometrics – Confocal Microscopes Display: – 3D Imaging Microscopes – Adaptive Illumination – Augmented Reality and Information Overlay In addition to the DLP9500 DMD, the 0.95 1080p chipset includes a dedicated DLPC410 controller required for high speed pattern rates of >23000 Hz (1-bit binary) and >1700 Hz (8-bit gray), one unit DLPR410 (DLP Discovery 4100 Configuration PROM), and two units DLPA200 (DMD micromirror drivers). Reliable function and operation of the DLP9500 requires that it be used in conjunction with the other components of the chipset. A dedicated chipset provides developers easier access to the DMD as well as high speed, independent micromirror control. DLP9500 is a digitally controlled microelectromechanical system (MEMS) spatial light modulator (SLM). When coupled to an appropriate optical system, the DLP9500 can be used to modulate the amplitude, direction, and/or phase of incoming light. Device Information PART NUMBER DLP9500 PACKAGE LCCC (355) (1) BODY SIZE (NOM) 42.16 mm × 42.16 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. Application Schematic 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com Table of Contents 1 2 3 4 5 6 7 Features .................................................................. 1 Applications ........................................................... 1 Description ............................................................. 1 Revision History..................................................... 2 Description (continued)......................................... 4 Pin Configuration and Functions ......................... 4 Specifications....................................................... 13 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 7.10 7.11 7.12 7.13 7.14 8 Absolute Maximum Ratings .................................... 13 Storage Conditions.................................................. 13 ESD Ratings............................................................ 13 Recommended Operating Conditions..................... 14 Thermal Information ................................................ 15 Electrical Characteristics......................................... 15 LVDS Timing Requirements ................................... 16 LVDS Waveform Requirements.............................. 17 Serial Control Bus Timing Requirements................ 18 Systems Mounting Interface Loads....................... 19 Micromirror Array Physical Characteristics ........... 20 Micromirror Array Optical Characteristics ............. 21 Window Characteristics......................................... 22 Chipset Component Usage Specification ............. 23 Detailed Description ............................................ 24 8.1 Overview ................................................................. 24 8.2 Functional Block Diagram ....................................... 24 8.3 8.4 8.5 8.6 8.7 9 Feature Description................................................. Device Functional Modes........................................ Window Characteristics and Optics ....................... Micromirror Array Temperature Calculation............ Micromirror Landed-On and Landed-Off Duty Cycle ........................................................................ 26 32 34 35 37 Application and Implementation ........................ 39 9.1 Application Information............................................ 39 9.2 Typical Application ................................................. 40 10 Power Supply Recommendations ..................... 42 10.1 Power-Up Sequence (Handled by the DLPC410) 42 10.2 DMD Power-Up and Power-Down Procedures..... 42 11 Layout................................................................... 43 11.1 Layout Guidelines ................................................. 43 11.2 Layout Example .................................................... 45 12 Device and Documentation Support ................. 46 12.1 12.2 12.3 12.4 12.5 12.6 Device Support .................................................... Documentation Support ........................................ Community Resources.......................................... Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 46 46 46 47 47 47 13 Mechanical, Packaging, and Orderable Information ........................................................... 47 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision B (July 2013) to Revision C Page • Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section ................................................................................................. 1 • Minor wording changes in Features and Description sections ............................................................................................... 1 • Changed name of Micromirror clocking pulse reset ............................................................................................................. 11 • Changed ESD Ratings table to match new standard........................................................................................................... 13 • Adjusted recommended power density conditions ............................................................................................................... 14 • Changed thermal test points to match new test point diagram ............................................................................................ 14 • Replaced Figure 3. ............................................................................................................................................................... 18 • Changed units from lbs to N................................................................................................................................................. 19 • Added Max Recommended DMD Temperature – Derating Curve....................................................................................... 22 • Added explanation for the15 MBRST lines to the DLP9500 from each DLPA200............................................................... 26 • Changed Thermal Test Point Location graphic .................................................................................................................... 35 • Added program interface to system interface list ................................................................................................................. 41 • Corrected number of banks of DMD mirrors to 15 ............................................................................................................... 41 • Removed link to DLP Discovery 4100 chipset datasheet..................................................................................................... 46 • Added Community Resources ............................................................................................................................................. 46 2 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 Changes from Revision A (September 2012) to Revision B Page • Added DLPR4101 enhanced PROM to DLPR410 in chipset list ........................................................................................... 1 • Added DLPR4101 Enhanced PROM to DLPR410 in Related Documentation .................................................................... 46 Changes from Original (August 2012) to Revision A • Page Changed the device From: Product Preview To: Production ................................................................................................. 1 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 3 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com 5 Description (continued) Electrically, the DLP9500 consists of a two-dimensional array of 1-bit CMOS memory cells, organized in a grid of 1920 memory cell columns by 1080 memory cell rows. The CMOS memory array is addressed on a row-by-row basis, over four 16-bit LVDS DDR buses. Addressing is handled by a serial control bus. The specific CMOS memory access protocol is handled by the DLPC410 digital controller. 6 Pin Configuration and Functions FLN Type A Package 355-Pin LCCC Bottom View 31 29 30 27 28 25 26 23 24 21 22 19 20 17 18 15 16 13 14 11 12 9 10 7 8 5 6 1 3 4 2 A B C D E F G H J K L M N P R T U V W Y AA AB AC AD AE AF AG AH AJ AK AL 4 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 Pin Functions PIN (1) NAME NO. TYPE (I/O/P) SIGNAL DATA RATE (2) INTERNAL TERM (3) CLOCK DESCRIPTION TRACE (MILS) DATA BUS A D_AN(0) F2 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 512.01 D_AN(1) H8 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 158.79 D_AN(2) E5 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 471.24 D_AN(3) G9 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 159.33 D_AN(4) D2 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 585.41 D_AN(5) G3 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 551.17 D_AN(6) E11 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 229.41 D_AN(7) F8 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 300.54 D_AN(8) C9 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 346.35 D_AN(9) H2 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 782.27 D_AN(10) B10 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 451.52 D_AN(11) G15 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 74.39 D_AN(12) D14 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 194.26 D_AN(13) F14 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A D_AN(14) C17 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 244.9 D_AN(15) H16 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 73.39 D_AP(0) F4 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 509.63 D_AP(1) H10 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 152.59 D_AP(2) E3 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 464.09 D_AP(3) G11 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 152.39 D_AP(4) D4 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 591.39 D_AP(5) G5 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 532.16 D_AP(6) E9 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 230.78 D_AP(7) F10 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 300.61 D_AP(8) C11 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 338.16 D_AP(9) H4 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 773.17 D_AP(10) B8 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 449.57 (1) (2) (3) Input data bus A (2x LVDS) 148.29 The following power supplies are required to operate the DMD: VCC, VCC1, VCC2. VSS must also be connected. DDR = Double Data Rate. SDR = Single Data Rate. Refer to the LVDS Timing Requirements for specifications and relationships. Refer to Electrical Characteristics for differential termination specification Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 5 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com Pin Functions (continued) PIN (1) NAME NO. TYPE (I/O/P) SIGNAL DATA RATE (2) INTERNAL TERM (3) CLOCK TRACE (MILS) DESCRIPTION D_AP(11) H14 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 71.7 D_AP(12) D16 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 198.69 D_AP(13) F16 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A D_AP(14) C15 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 240.14 D_AP(15) G17 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A 74.05 D_BN(0) AH2 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 525.25 D_BN(1) AD8 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 190.59 D_BN(2) AJ5 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 525.25 D_BN(3) AE3 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 494.91 D_BN(4) AG9 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 222.67 D_BN(5) AE11 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 205.45 D_BN(6) AH10 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 309.05 D_BN(7) AF10 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 285.62 D_BN(8) AK8 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 483.58 D_BN(9) AG5 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 711.58 D_BN(10) AL11 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 462.21 D_BN(11) AE15 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 74.39 D_BN(12) AH14 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B D_BN(13) AF14 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 156 D_BN(14) AJ17 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 247.9 D_BN(15) AD16 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 111.52 D_BP(0) AH4 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 525.02 D_BP(1) AD10 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 190.61 D_BP(2) AJ3 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 524.22 D_BP(3) AE5 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 476.07 D_BP(4) AG11 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 222.8 D_BP(5) AE9 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 219.48 D_BP(6) AH8 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 306.55 D_BP(7) AF8 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 298.04 D_BP(8) AK10 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 480.31 Input data bus A (2x LVDS) 143.72 DATA BUS B 6 Submit Documentation Feedback Input data bus B (2x LVDS) 194.26 Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 Pin Functions (continued) PIN (1) NAME NO. TYPE (I/O/P) SIGNAL DATA RATE (2) INTERNAL TERM (3) CLOCK DESCRIPTION TRACE (MILS) D_BP(9) AG3 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 727.18 D_BP(10) AL9 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 461.02 D_BP(11) AD14 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 71.35 D_BP(12) AH16 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B D_BP(13) AF16 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 150.38 D_BP(14) AJ15 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 243.14 D_BP(15) AE17 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B 113.36 D_CN(0) B14 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 459.04 D_CN(1) E15 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 342.79 D_CN(2) A17 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 456.22 D_CN(3) G21 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 68.24 D_CN(4) B20 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 362.61 D_CN(5) F20 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 163.07 D_CN(6) D22 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 204.16 D_CN(7) G23 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 105.59 D_CN(8) B26 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 450.51 D_CN(9) F28 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 302.04 D_CN(10) C29 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C D_CN(11) G27 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C D_CN(12) D26 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 276.76 D_CN(13) H28 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 186.78 D_CN(14) E29 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 311.3 D_CN(15) J29 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 262.62 D_CP(0) B16 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 463.64 D_CP(1) E17 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 347.65 D_CP(2) A15 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 456.45 D_CP(3) H20 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 67.72 D_CP(4) B22 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 362.76 D_CP(5) F22 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 161.69 Input data bus B (2x LVDS) 197.69 DATA BUS C Input data bus C (2x LVDS) 429.8 317.1 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 7 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com Pin Functions (continued) PIN (1) NAME NO. TYPE (I/O/P) SIGNAL DATA RATE (2) INTERNAL TERM (3) CLOCK DESCRIPTION TRACE (MILS) D_CP(6) D20 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 195.09 D_CP(7) H22 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 104.86 D_CP(8) B28 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 451.41 D_CP(9) F26 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 294.22 D_CP(10) C27 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C D_CP(11) G29 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C D_CP(12) D28 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 276.04 D_CP(13) H26 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 186.25 D_CP(14) E27 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 312.07 D_CP(15) J27 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C 262.94 D_DN(0) AK14 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 492.53 D_DN(1) AG15 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 342.78 D_DN(2) AL17 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 491.83 D_DN(3) AE21 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 74.24 D_DN(4) AK20 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 356.23 D_DN(5) AF20 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D D_DN(6) AH22 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D D_DN(7) AE23 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 105.59 D_DN(8) AK26 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 450.51 D_DN(9) AF28 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 302.04 D_DN(10) AJ29 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 429.8 D_DN(11) AE27 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 298.87 Input data bus C (2x LVDS) 429.68 314.98 DATA BUS D 8 Submit Documentation Feedback Input data bus D (2x LVDS) 163.07 204.16 Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 Pin Functions (continued) PIN (1) NAME NO. TYPE (I/O/P) SIGNAL DATA RATE (2) INTERNAL TERM (3) CLOCK DESCRIPTION TRACE (MILS) D_DN(12) AH26 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 276.76 D_DN(13) AD28 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 186.78 D_DN(14) AG29 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 311.3 D_DN(15) AC29 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 262.62 D_DP(0) AK16 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 495.13 D_DP(1) AG17 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 342.47 D_DP(2) AL15 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 492.06 D_DP(3) AD20 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 67.72 D_DP(4) AK22 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 356.37 D_DP(5) AF22 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D D_DP(6) AH20 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D D_DP(7) AD22 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 102.86 D_DP(8) AK28 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 451.41 D_DP(9) AF26 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 296.7 D_DP(10) AJ27 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 429.68 D_DP(11) AE29 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 302.74 D_DP(12) AH28 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 276.04 D_DP(13) AD26 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 186.25 D_DP(14) AG27 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 312.07 D_DP(15) AC27 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D 262.94 Input data bus D (2x LVDS) 161.98 195.09 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 9 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com Pin Functions (continued) PIN (1) NAME NO. TYPE (I/O/P) SIGNAL DATA RATE (2) INTERNAL TERM CLOCK (3) DESCRIPTION TRACE (MILS) DATA CLOCKS DCLK_AN D10 Input LVCMOS — Differentially terminated – 100 Ω — DCLK_AP D8 Input LVCMOS — Differentially terminated – 100 Ω — DCLK_BN AJ11 Input LVCMOS — Differentially terminated – 100 Ω — DCLK_BP AJ9 Input LVCMOS — Differentially terminated – 100 Ω — DCLK_CN C23 Input LVCMOS — Differentially terminated – 100 Ω — DCLK_CP C21 Input LVCMOS — Differentially terminated – 100 Ω — DCLK_DN AJ23 Input LVCMOS — Differentially terminated – 100 Ω — DCLK_DP AJ21 Input LVCMOS — Differentially terminated – 100 Ω — Input data bus A Clock (2x LVDS) Input data bus B Clock (2x LVDS) Input data bus C Clock (2x LVDS) Input data bus D Clock (2x LVDS) 325.8 319.9 318.92 318.74 252.01 241.18 252.01 241.18 DATA CONTROL INPUTS SCTRL_AN J3 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A SCTRL_AP J5 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_A SCTRL_BN AF4 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B SCTRL_BP AF2 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_B SCTRL_CN E23 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C SCTRL_CP E21 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_C SCTRL_DN AG23 Input LVCMOS DDR Differentially terminated – 100 Ω DCLK_D SCTRL_DP AG21 Input LVCMOS DDR Differentially terminated – 100 Ω Serial control for data bus A (2x LVDS) 608.14 Serial control for data bus B (2x LVDS) 698.12 Serial control for data bus C (2x LVDS) 232.46 235.53 DCLK_D Serial control for data bus D (2x LVDS) 607.45 703.8 235.21 235.66 SERIAL COMMUNICATION AND CONFIGURATION SCPCLK AE1 Input LVCMOS — pull-down — Serial port clock 324.26 SCPDO AC3 Output LVCMOS — — SCP_CLK Serial port output 281.38 SCPDI AD2 Input LVCMOS — pull-down SCP_CLK Serial port input 261.55 SCPEN AD4 Input LVCMOS — pull-down SCP_CLK Serial port enable 184.86 PWRDN B4 Input LVCMOS — pull-down — Device reset 458.78 MODE_A J1 Input LVCMOS — pull-down — G1 Input LVCMOS — pull-down — Data bandwidth mode select 471.57 MODE_B 10 Submit Documentation Feedback 521.99 Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 Pin Functions (continued) PIN (1) NAME NO. TYPE (I/O/P) SIGNAL DATA RATE (2) INTERNAL TERM CLOCK (3) TRACE (MILS) DESCRIPTION MICROMIRROR CLOCKING PULSE (BIAS RESET) MBRST(0) L5 Input Analog — — — 898.97 MBRST(1) M28 Input Analog — — — 621.98 MBRST(2) P4 Input Analog — — — 846.88 MBRST(3) P30 Input Analog — — — 784.18 MBRST(4) L3 Input Analog — — — 763.34 MBRST(5) P28 Input Analog — — — 749.61 MBRST(6) P2 Input Analog — — — 878.25 MBRST(7) T28 Input Analog — — — 783.83 MBRST(8) M4 Input Analog — — — 969.36 MBRST(9) L29 Input Analog — — — 621.24 MBRST(10) T4 Input Analog — — — 918.43 MBRST(11) N29 Input Analog — — — MBRST(12) N3 Input Analog — — — MBRST(13) L27 Input Analog — — — MBRST(14) R3 Input Analog — — — MBRST(15) V28 Input Analog — — — MBRST(16) V4 Input Analog — — — MBRST(17) R29 Input Analog — — — MBRST(18) Y4 Input Analog — — — 715 MBRST(19) AA27 Input Analog — — — 604.35 MBRST(20) W3 Input Analog — — — 832.39 MBRST(21) W27 Input Analog — — — 675.21 MBRST(22) AA3 Input Analog — — — 861.18 MBRST(23) W29 Input Analog — — — 662.66 MBRST(24) U5 Input Analog — — — 850.06 MBRST(25) U29 Input Analog — — — 726.56 MBRST(26) Y2 Input Analog — — — 861.48 MBRST(27) AA29 Input Analog — — — 683.83 MBRST(28) U3 Input Analog — — — 878.5 MBRST(29) Y30 Input Analog — — — 789.2 Power Analog — — — Power for LVCMOS logic — Power Analog — — — Power supply for LVDS Interface — 685.14 Micromirror clocking pulse reset MBRST signals clock micromirrors into state of LVCMOS memory cell associated with each mirror. 812.31 591.89 878.5 660.15 848.64 796.31 POWER A3, A5, A7, A9, A11, A13, A21, A23, A25, A27, A29, B2, VCC C1, C31, E31, G31, J31, K2, L31, N31, R31, U31, W31, AA31, AC1, AC31, AE31, AG1, AG31, AJ31, AK2, AK30, AL3, AL5, AL7, AL19, AL21, AL23, AL25, AL27 VCCI H6, H12, H18, H24, M6, M26, P6, P26, T6, T26, V6, V26, Y6, Y26, AD6, AD12, AD18, AD24 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 11 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com Pin Functions (continued) PIN (1) NAME NO. L1, N1, R1, U1, W1, AA1 VCC2 TYPE (I/O/P) SIGNAL DATA RATE (2) INTERNAL TERM CLOCK (3) TRACE (MILS) DESCRIPTION Power Analog — — — Power for high voltage CMOS logic — Power Analog — — — Common return for all power inputs — A1, B12, B18, B24, B30, C7, C13, C19, C25, D6, D12, D18, D24, D30, E1, E7, E13, E19, E25, F6, F12, F18, F24, F30, G7, G13, G19, G25, K4, K6, K26, K28, K30, M2, M30, N5, N27, R5, T2, T30, U27, V2, V30, W5, Y28, AB2, AB4, VSS AB6, AB26, AB28, AB30, AD30, AE7, AE13, AE19, AE25, AF6, AF12, AF18, AF24, AF30, AG7, AG13, AG19, AG25, AH6, AH12, AH18, AH24, AH30, AJ1, AJ7, AJ13, AJ19, AJ25, AK6, AK12, AK18, AL29 RESERVED SIGNALS (NOT FOR USE IN SYSTEM) RESERVED_FC J7 Input LVCMOS — pull-down — RESERVED_FD J9 Input LVCMOS — pull-down — RESERVED_PFE J11 Input LVCMOS — pull-down — RESERVED_STM AC7 Input LVCMOS — pull-down — — RESERVED_AE C3 Input LVCMOS — pull-down — — A19, B6, C5, H30, J13, J15, J17, J19, J21, J23, J25, R27, NO_CONNECT AA5, AC11, AC13, AC15, AC17, AC19, AC21, AC23, — — — — — — — Pins should be connected to VSS No connection (any connection to these terminals may result in undesirable effects) — — AC25, AC5, AC9, AK24, AK4, AL13 12 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 7 Specifications 7.1 Absolute Maximum Ratings over operating free-air temperature (unless otherwise noted). (1) MIN MAX UNIT ELECTRICAL VCC Voltage applied to VCC (2) (3) –0.5 4 V VCCI Voltage applied to VCCI (2) (3) –0.5 4 V VCC2 Voltage applied to VVCC2 –0.5 9 V VMBRST Clocking pulse waveform voltage applied to MBRST[29:0] input pins (supplied by DLPA200s) –28 28 V 0.3 V |VCC – VCCI| (2) (3) (4) Supply voltage delta (absolute value) (4) Voltage applied to all other input terminals |VID| (2) VCC + 0.3 V Maximum differential voltage, damage can occur to internal termination resistor if exceeded, see Figure 2 –0.5 700 mV Current required from a high-level output, VOH = 2.4 V –20 mA Current required from a low-level output, VOL = 0.4 V 15 mA 20 70 °C –40 80 °C ENVIRONMENTAL Case temperature – operational TC Case temperature – non-operational TGRADIENT (1) (2) (3) (4) (5) (6) (5) (5) (6) 10 °C Operating relative humidity (non-condensing) 95 %RH Device temperature gradient – operational Stresses beyond those listed under Recommended Operating Conditions may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions . Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages referenced to VSS (ground). Voltages VCC, VCCI, and VCC2 are required for proper DMD operation. Exceeding the recommended allowable absolute voltage difference between VCC and VCCI may result in excess current draw. The difference between VCC and VCCI, | VCC – VCCI|, should be less than the specified limit. DMD Temperature is the worst-case of any test point shown in Case Temperature, or the active array as calculated by the Micromirror Array Temperature Calculation. As measured between any two points on the exterior of the package, or as predicted between any two points inside the micromirror array cavity. Refer to Case Temperature and Micromirror Array Temperature Calculation. 7.2 Storage Conditions applicable before the DMD is installed in the final product Tstg Storage temperature MIN MAX –40 80 °C 95 %RH Storage humidity (non-condensing) UNIT 7.3 ESD Ratings VALUE VESD (1) Electrostatic discharge Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) All pins except MBRST[29:0] ±2000 MBRST[29:0] pins ±250 UNIT V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. Manufacturing with less than 500-V HBM is possible if necessary precautions are taken. Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 13 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com 7.4 Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted). SUPPLY VOLTAGES (1) MIN NOM MAX UNIT (2) (3) VCC Supply voltage for LVCMOS core logic 3.0 3.3 3.6 V VCCI Supply voltage for LVDS receivers 3.0 3.3 3.6 V VCC2 Mirror electrode and HVCMOS supply voltage 8.25 8.5 8.75 V VMBRST Clocking Pulse Waveform Voltage applied to MBRST[29:0] Input Pins (supplied by DLPA200s) 26.5 V |VCC – VCCI| Supply voltage delta (absolute value) 0.3 V TGRADIENT Operating Case Temperature (7) Operating Case Temperature (7) (6) : Thermal Test Points 2 and 3 (8) : Thermal Test Point 1 and Array Device temperature gradient – operational (8) 20 25-45 70 (8) °C 20 25-45 65 (8) °C 10 °C (9) Operating relative humidity (non-condensing) ILLVIS -27 (5) ENVIRONMENTAL – For Illumination Source between 420 and 700 nm TC (4) 0 Illumination Thermally limited ENVIRONMENTAL – For Illumination Source between 400 and 420 nm TC TGRADIENT Operating Case Temperature (7) Operating Case Temperature (7) (8) : Thermal Test Point 1 and Array (8) 20 25-45 70 (8) °C 20 25-45 65 (8) °C (9) Operating relative humidity (non-condensing) ILLVIS TC TGRADIENT Operating case temperature (7) Operating case temperature (7) 10 °C 95 %RH 2.5 W/cm2 0 Illumination ENVIRONMENTAL – For Illumination Source <400 and >700 nm %RH W/cm2 (6) : Thermal Test Points 2 and 3 Device temperature gradient – operational 95 (10) (6) : Thermal test points 2 and 3 (8) : Thermal test point 1 and array Device temperature gradient – operational 20 (8) 20 (9) Operating relative humidity (non-condensing) 0 25-45 25-45 70 (8) °C 65 (8) °C 10 °C 95 %RH ILLUV Illumination, wavelength < 400 nm 0.68 mW/cm2 ILLIR Illumination, wavelength > 700 nm 10 mW/cm2 (1) The functional performance of the device specified in this data sheet is achieved when operating the device within the limits defined by the Recommended Operating Conditions. No level of performance is implied when operating the device above or below the Recommended Operating Conditions limits. (2) Supply voltages VCC, VCCI, VOFFSET, VBIAS, and VRESET are all required for proper DMD operation. VSS must also be connected. (3) All voltages are referenced to common ground VSS. (4) Voltages VCC, VCCI, and VCC2, are required for proper DMD operation. (5) Exceeding the recommended allowable absolute voltage difference between VCC and VCCI may result in excess current draw. The difference between VCC and VCCI, | VCC – VCCI|, should be less than the specified limit. (6) Optimal, long-term performance and optical efficiency of the Digital Micromirror Device (DMD) can be affected by various application parameters, including illumination spectrum, illumination power density, micromirror landed duty-cycle, ambient temperature (storage and operating), DMD temperature, ambient humidity (storage and operating), and power on or off duty cycle. TI recommends that application-specific effects be considered as early as possible in the design cycle. (7) In some applications, the total DMD heat load can be dominated by the amount of incident light energy absorbed. See Micromirror Array Temperature Calculation for further details. (8) See the Micromirror Array Temperature Calculation for thermal test point locations, package thermal resistance, and device temperature calculation. (9) As measured between any two points on the exterior of the package, or as predicted between any two points inside the micromirror array cavity. Refer to Case Temperature and Micromirror Array Temperature Calculation. (10) Refer to Case Temperature and Micromirror Array Temperature Calculation. 14 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 7.5 Thermal Information DLP9500 THERMAL METRIC (1) (2) LCCC UNIT 355 PINS Active micromirror array resistance to TC2 (1) (2) 0.5 °C/W The DMD is designed to conduct absorbed and dissipated heat to the back of the package where it can be removed by an appropriate heat sink. The heat sink and cooling system must be capable of maintaining the package within the temperature range specified in the Recommended Operating Conditions. The total heat load on the DMD is largely driven by the incident light absorbed by the active area; although other contributions include light energy absorbed by the window aperture and electrical power dissipation of the array. Optical systems should be designed to minimize the light energy falling outside the window clear aperture since any additional thermal load in this area can significantly degrade the reliability of the device. For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report, SPRA953. 7.6 Electrical Characteristics over the range of recommended supply voltage and recommended case operating temperature (unless otherwise noted); under recommended operating conditions PARAMETER TEST CONDITIONS (1) VOH High-level output voltage See Figure 11 Low-level output voltage See Figure 11 (1) VOL VMBRST Clocking pulse waveform applied to MBRST[29:0] input pins (supplied by DLPA200s) IOZ High-impedance output current IOH IOL , VCC = 3 V, IOH = –20 mA , High-level output current (1) Low-level output current (1) MIN –27 VCC = 3.6 V V 10 µA –15 VOL = 0.4 V, VCC ≥ 3 V 15 VOL = 0.4 V, VCC ≥ 2.25 V 14 Low-level input voltage IIL Low-level input current (1) IIH High-level input current ICC Current into VCC pin ICCI Current into VOFFSET pin ICC2 Current into VCC2 pin PD Power dissipation ZIN Internal differential impedance 95 ZLINE Line differential impedance (PWB, trace) 90 CI Input capacitance CO Output capacitance CIM Input capacitance for MBRST[29:0] pins (1) (2) 26.5 VOH = 1.7 V, VCC ≥ 2.25 V VIL (2) V –20 (1) (1) 0.4 VOH = 2.4 V, VCC ≥ 3 V (1) 1.7 VCC + .3 –0.3 (1) mA mA V 0.7 V VCC = 3.6 V, VI = 0 V –60 µA VCC = 3.6 V, VI = VCC 60 µA VCC = 3.6 V, 2990 mA VCCI = 3.6 V 910 mA 25 mA VCC2 = 8.75 V 4.4 (1) UNIT V VCC = 3.6 V, IOH = 15 mA (1) MAX 2.4 High-level input voltage VIH TYP ƒ = 1 MHz ƒ = 1 MHz ƒ = 1 MHz 270 W 105 100 Ω 110 Ω 10 pF 10 pF 355 pF Applies to LVCMOS pins only. Exceeding the maximum allowable absolute voltage difference between VCC and VCCI may result in excess current draw. (See Absolute Maximum Ratings for details.) Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 15 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com 7.7 LVDS Timing Requirements over operating free-air temperature range (unless otherwise noted); see Figure 1 MIN ƒDCLK_x DCLK_x clock frequency (where x = [A, B, C, or D]) 200 tc Clock cycle - DLCK_x 2.5 tw Pulse duration - DLCK_x ts Setup time - D_x[15:0] and SCTRL_x before DCLK_x th Hold time, D_x[15:0] and SCTRL_x after DCLK_x tskew Skew between any two buses (A ,B, C, and D) NOM MAX UNIT 400 MHz ns 1.25 ns .35 ns .35 –1.25 ns 1.25 ns DCLK_AN DCLK_AP th tw tw tc ts ts th SCTRL_AN SCTRL_AP tskew D_AN(15:0) D_AP(15:0) DCLK_BN DCLK_BP tw tw ts th tc ts th SCTRL_BN SCTRL_BP D_BN(15:0) D_BP(15:0) tw DCLK_CN DCLK_CP ts th tw tc ts th SCTRL_CN SCTRL_CP tskew D_CN(15:0) D_CP(15:0) DCLK_DN DCLK_DP tw tw ts th tc th ts SCTRL_DN SCTRL_DP D_DN(15:0) D_DP(15:0) Figure 1. LVDS Timing Waveforms 16 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 7.8 LVDS Waveform Requirements over operating free-air temperature range (unless otherwise noted); see Figure 2 MIN |VID| Input differential voltage (absolute difference) VCM Common mode voltage VLVDS LVDS voltage tr tr 100 NOM MAX UNIT 400 600 mV 1200 mV 0 2000 mV Rise time (20% to 80%) 100 400 ps Fall time (80% to 20%) 100 400 ps V LVDS max = V CM max + | 1/2 × VID max | tf VID V CM tr VLVDS min = V CM min ± | 1/2 × VID max | Figure 2. LVDS Waveform Requirements Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 17 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com 7.9 Serial Control Bus Timing Requirements over operating free-air temperature range (unless otherwise noted); see Figure 3 and Figure 4 MIN NOM MAX UNIT 50 500 kHz –300 300 ns 960 ns ƒSCP_CLK SCP clock frequency tSCP_SKEW Time between valid SCP_DI and rising edge of SCP_CLK tSCP_DELAY Time between valid SCP_DO and rising edge of SCP_CLK t SCP_EN Time between falling edge of SCP_EN and the first rising edge of SCP_CLK t_SCP Rise time for SCP signals 200 ns tƒ_SCP Fall time for SCP signals 200 ns tc SCPCLK 30 ns fclock = 1 / tc 50% 50% tSCP_SKEW SCPDI 50% tSCP_DELAY SCPD0 50% Figure 3. Serial Communications Bus Timing Parameters tr_SCP tf_SCP Input Controller VCC SCP_CLK, SCP_DI, SCP_EN VCC/2 0v Figure 4. Serial Communications Bus Waveform Requirements 18 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 7.10 Systems Mounting Interface Loads PARAMETER Maximum system mounting interface load to be applied to the: MAX UNIT Thermal interface area (see Figure 5) MIN NOM 156 N Electrical interface area (see Figure 5) 1334 N Datum A Interface area (see Figure 5) 712 N Thermal Interface Area Electrical Interface Area Other Area Datum ‘A’ Areas Figure 5. System Interface Loads Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 19 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com 7.11 Micromirror Array Physical Characteristics See Mechanical, Packaging, and Orderable Information for additional details. M Number of active micromirror columns N Number of active micromirror rows P Micromirror (pixel) pitch 1920 micromirrors 1080 micromirrors (1) (1) Micromirror active array height (1) (1) (2) 10.8 µm M×P 20.736 mm N×P 11.664 mm 10 micromirrors/side Pond of micromirrors (POM) M±4 M±3 M±2 M±1 See Figure 6. The structure and qualities of the border around the active array includes a band of partially functional micromirrors called the POM. These micromirrors are structurally and/or electrically prevented from tilting toward the bright or ON state, but still require an electrical bias to tilt toward OFF. 0 1 2 3 (1) (2) UNIT (1) Micromirror active array width Micromirror array border VALUE (1) 0 1 2 3 DMD Active Array NxP M x N Micromirrors N±4 N±3 N±2 N±1 MxP P Border micromirrors omitted for clarity. Details omitted for clarity. P Not to scale. P P Refer to the Micromirror Array Physical Characteristics table for M, N, and P specifications. Figure 6. Micromirror Array Physical Characteristics 20 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 7.12 Micromirror Array Optical Characteristics TI assumes no responsibility for end-equipment optical performance. Achieving the desired end-equipment optical performance involves making trade-offs between numerous component and system design parameters. See the related application reports (listed in Related Documentation) for guidelines. PARAMETER a Micromirror tilt angle β Micromirror tilt angle variation Micromirror crossover time TEST CONDITIONS (1) (4) (6) (7) (8) MIN (1) (2) (3) 0 DMD landed state See Figure 12 (1) (4) (5) 12 , See Figure 12 16 Micromirror array optical efficiency (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (13) (14) See Figure 12 400 to 700 nm, with all micromirrors in the ON state degrees 1 degrees 22 µs 10 0 44 UNIT µs Adjacent micromirrors (12) MAX 56 Non-adjacent micromirrors (11) Orientation of the micromirror axis-of-rotation (1) (2) –1 (9) Micromirror switching time at 400 MHz with global reset (10) Non-operating micromirrors TYP DMD parked state See Figure 12 45 46 micromirrors degrees 68% Measured relative to the plane formed by the overall micromirror array Parking the micromirror array returns all of the micromirrors to an essentially flat (0˚) state (as measured relative to the plane formed by the overall micromirror array). When the micromirror array is parked, the tilt angle of each individual micromirror is uncontrolled. Additional variation exists between the micromirror array and the package datums, as shown in Mechanical, Packaging, and Orderable Information. When the micromirror array is landed, the tilt angle of each individual micromirror is dictated by the binary contents of the CMOS memory cell associated with each individual micromirror. A binary value of 1 results in a micromirror landing in an nominal angular position of +12°. A binary value of 0 results in a micromirror landing in an nominal angular position of –12°. Represents the landed tilt angle variation relative to the nominal landed tilt angle. Represents the variation that can occur between any two individual micromirrors, located on the same device or located on different devices. For some applications, it is critical to account for the micromirror tilt angle variation in the overall system optical design. With some system optical designs, the micromirror tilt angle variation within a device may result in perceivable non-uniformities in the light field reflected from the micromirror array. With some system optical designs, the micromirror tilt angle variation between devices may result in colorimetry variations and/or system contrast variation. Micromirror crossover time is primarily a function of the natural response time of the micromirrors. Micromirror switching is controlled and coordinated by the DLPC410 (DLPS024) and DLPA200 (DLPS015). Nominal switching time depends on the system implementation and represents the time for the entire micromirror array to be refreshed. Non-operating micromirror is defined as a micromirror that is unable to transition nominally from the –12° position to +12° or vice versa. Measured relative to the package datums 'B' and 'C', shown in the Mechanical, Packaging, and Orderable Information. The minimum or maximum DMD optical efficiency observed in a specific application depends on numerous application-specific design variables, such as: (a) Illumination wavelength, bandwidth/line-width, degree of coherence (b) Illumination angle, plus angle tolerance (c) Illumination and projection aperture size, and location in the system optical path (d) Illumination overfill of the DMD micromirror array (e) Aberrations present in the illumination source and/or path (f) Aberrations present in the projection path The specified nominal DMD optical efficiency is based on the following use conditions: (a) Visible illumination (400 to 700 nm ) (b) Input illumination optical axis oriented at 24° relative to the window normal (c) Projection optical axis oriented at 0° relative to the window normal (d) ƒ / 3 illumination aperture (e) ƒ / 2.4 projection aperture Based on these use conditions, the nominal DMD optical efficiency results from the following four components: (a) Micromirror array fill factor: nominally 92% (b) Micromirror array diffraction efficiency: nominally 86% (c) Micromirror surface reflectivity: nominally 88% (d) Window transmission: nominally 97% (single pass, through two surface transitions) (14) Does not account for the effect of micromirror switching duty cycle, which is application dependent. Micromirror switching duty cycle represents the percentage of time that the micromirror is actually reflecting light from the optical illumination path to the optical projection path. This duty cycle depends on the illumination aperture size, the projection aperture size, and the micromirror array update rate. Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 21 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com 7.13 Window Characteristics PARAMETER (1) TEST CONDITIONS Window material designation Corning 7056 Window refractive index At wavelength 589 nm Window flatness (2) Window aperture See Illumination overfill Refer to Illumination Overfill (4) (5) MAX 4 Within the Window Aperture Window transmittance, single–pass through both surfaces and glass (5) TYP UNIT 1.487 Per 25 mm Window artifact size (1) (2) (3) MIN (3) 400 fringes µm (4) At wavelength 405 nm. Applies to 0° and 24° AOI only. 95% Minimum within the wavelength range 420 nm to 680 nm. Applies to all angles 0° to 30° AOI. 97% Average over the wavelength range 420 nm to 680 nm. Applies to all angles 30° to 45° AOI. 97% See Window Characteristics and Optics for more information. At a wavelength of 632.8 nm. See the Mechanical, Packaging, and Orderable Information section at the end of this document for details regarding the size and location of the window aperture. For details regarding the size and location of the window aperture, see the package mechanical characteristics listed in the Mechanical ICD in the Mechanical, Packaging, and Orderable Information section. See the TI application report DLPA031, Wavelength Transmittance Considerations for DLP DMD Window. Figure 7. Max Recommended DMD Temperature – Derating Curve 22 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 7.14 Chipset Component Usage Specification The DLP9500 is a component of one or more DLP chipsets. Reliable function and operation of the DLP9500 requires that it be used in conjunction with the other components of the applicable DLP chipset, including those components that contain or implement TI DMD control technology. TI DMD control technology is the TI technology and devices for operating or controlling a DLP DMD. Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 23 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com 8 Detailed Description 8.1 Overview Optically, the DLP9500 consists of 2,073,600 highly reflective, digitally switchable, micrometer-sized mirrors (micromirrors), organized in a two-dimensional array of 1920 micromirror columns by 1080 micromirror rows (). Each aluminum micromirror is approximately 10.8 microns in size (see the Micromirror Pitch in ) and is switchable between two discrete angular positions: –12° and 12°. The angular positions are measured relative to a 0° flat state, which is parallel to the array plane (see Figure 12). The tilt direction is perpendicular to the hingeaxis, which is positioned diagonally relative to the overall array. The On State landed position is directed toward row 0, column 0 (upper left) corner of the device package (see the Micromirror Hinge-Axis Orientation in ). In the field of visual displays, the 1920 × 1080 pixel resolution is referred to as 1080p. Each individual micromirror is positioned over a corresponding CMOS memory cell. The angular position of a specific micromirror is determined by the binary state (logic 0 or 1) of the corresponding CMOS memory cell contents, after the mirror clocking pulse is applied. The angular position (–12° or +12°) of the individual micromirrors changes synchronously with a micromirror clocking pulse, rather than being synchronous with the CMOS memory cell data update. Therefore, writing a logic 1 into a memory cell followed by a mirror clocking pulse will result in the corresponding micromirror switching to a 12° position. Writing a logic 0 into a memory cell followed by a mirror clocking pulse will result in the corresponding micromirror switching to a –12° position. Updating the angular position of the micromirror array consists of two steps. First, updating the contents of the CMOS memory. Second, application of a micromirror clocking pulse to all or a portion of the micromirror array (depending upon the configuration of the system). Micromirror clocking pulses are generated externally by two DLPA200s, with application of the pulses being coordinated by the DLPC410 controller. Around the perimeter of the 1920 by 1080 array of micromirrors is a uniform band of border micromirrors. The border micromirrors are not user-addressable. The border micromirrors land in the –12° position once power has been applied to the device. There are 10 border micromirrors on each side of the 1920 by 1080 active array. Figure 8 shows a DLPC410 and DLP9500 chipset block diagram. The DLPC410 and DLPA200s control and coordinate the data loading and micromirror switching for reliable DLP9500 operation. The DLPR410 is the programmed PROM required to properly configure the DLPC410 controller. For more information on the chipset components, see Application and Implementation. For a typical system application using the DLP Discovery 4100 chipset including a DLP9500, see Figure 18. 8.2 Functional Block Diagram Figure 8 shows a simplified system block diagram with the use of the DLPC410 with the following chipset components: DLPC410 Xilinx [XC5VLX30] FPGA configured to provide high-speed DMD data and control, and DLPA200 timing and control DLPR410 [XCF16PFSG48C] serial flash PROM contains startup configuration information (EEPROM) DLPA200 Two DMD micromirror drivers for the DLP9500 DMD DLP9500 Spatial light modulator (DMD) 24 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 DLPC410 PWR_FLOAT ROWMD(1:0) ROWAD(10:0) RST2BLKZ BLKMD(1:0) BLKAD(10:0) ECP2_FINISHED DMD_TYPE(3:0) Bank A Input Bank B Input Bank C Input DDC_DCLKOUT_C DDC_SCTRL_C Bank B Input DDC_DOUT_C(15:0) DDC_DCLKOUT_D DDC_SCTRL_D DDC_DOUT_D(15:0) DMD SCP SCPCLK SCPDO SCPDI DMD_A_SCPENZ DMD_B_SCPENZ A_SCPENZ B_SCPENZ A_STROBE A_MODE(1:0) A_SEL(1:0) A_ADDR(3:0) DLPA200 A MBRST1_(15:0) OEZ INIT PROM_CCK_DDC DONE_DDC INTB_DDC RDWR_B_0 TDO_XCF16DDC TCK_JTAG TCK_JTAG TDO_DDC DDC_M(2:0) ECP2_M_TP(31:0) B_SEL(1:0) B_ADDR(3:0) B MBRST2_(15:0) JTAG Interface HSWAPEN_0 B_STROBE B_MODE(1:0) DLPA200 Resets Side 2 PROM_DO_DDC Resets PROGB_DDC CS_B_0 JTAG Header DDC_DOUT_B(15:0) DLPA200 B SCP TDI_JTAG JTAG Interface DLPR410 Program Interface DDC_VERSION(2:0) Program Interface Info Input INIT_ACTIVE Info Output RST_ACTIVE Serial Data Bus WDT_ENBLZ DLPA200 A Output STEPVCC DLPA200 B Output Control Signals Output NS_FLIP Control Signals Input COMP_DATA DDC_SCTRL_B Resets Side 1 DDC_DIN_D(15:0) DDC_DCLKOUT_B Resets DVALID_D DDC_DOUT_A(15:0) DLPA200 A SCP DDC_DCLK_D DDC_SCTRL_A DLPA200 B Input Bank D Output DDC_DIN_C(15:0) DDC_DCLKOUT_A DLPA200 A Input DVALID_C Bank A Output DDC_DCLK_C Bank B Output Bank C Output DDC_DIN_B(15:0) Bank C Output DVALID_B Bank B Output DDC_DCLK_B Bank A Input Bank B Output DDC_DIN_A(15:0) Bank B Input DVALID_A Bank C Input DDC_DCLK_A DLP9500 = LVDS Bus Bank D Input Bank A Output USER INTERFACE VLED0 VLED1 DDCSPARE(1:0) OSC 50 Mhz ARSTZ DMD_A_RESET CLKIN_R DMD_B_RESET Figure 8. DLPC410, DLPA200, DLPR410, and DLP9500 Functional Block Diagram Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 25 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com 8.3 Feature Description Table 1. DMD Overview DMD ARRAY SINGLE BLOCK MODE (PATTERNS/s) GLOBAL RESET MODE (PATTERNS/s) DATA RATE (GIGA PIXELS/s) MIRROR PITCH DLP9500 - 0.95" 1080p 1920 × 1080 23148 17857 48 10.8 μm 8.3.1 DLPC410 Controller The DLPC410 chipset includes the DLPC410 controller which provides a high-speed LVDS data and control interface for DMD control. This interface is also connected to a second FPGA used to drive applications (not included in the chipset). The DLPC410 generates DMD and DLPA200 initialization and control signals in response to the inputs on the control interface. For more information, see the DLPC410 data sheet (DLPS024). 8.3.2 DLPA200 DMD Micromirror Drivers DLPA200 micromirror drivers provide the micromirror clocking pulse driver functions for the DMD. Two drivers are required for DLP9500. The DLPA200 is designed to work with multiple DLP chipsets. Although the DLPA200 contains 16 MBSRT output pins, only 15 lines are used with the DLP9500 chipset. For more information see and the DLPA200 data sheet (DLPS015). 8.3.3 Flash Configuration PROM The DLPC410 is configured at startup from the serial flash PROM. The contents of this PROM can not be altered. For more information, see the DLPC410 data sheet (DLPS024) and DLPR410 data sheet (DLPS027). 8.3.4 DMD 8.3.4.1 DLP9500 1080p Chipset Interfaces This section will describe the interface between the different components included in the chipset. For more information on component interfacing, see Application and Implementation. 8.3.4.1.1 DLPC410 Interface Description 8.3.4.1.1.1 DLPC410 IO Table 2 describes the inputs and outputs of the DLPC410 to the user. For more details on these signals, see the DLPC410 data sheet (DLPS024). 26 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 Table 2. Input/Output Description PIN NAME DESCRIPTION I/O ARST Asynchronous active low reset I CLKIN_R Reference clock, 50 MHz I DIN_[A,B,C,D](15:0) LVDS DDR input for data bus A,B,C,D (15:0) I DCLKIN[A,B,C,D] LVDS inputs for data clock (200 - 400 MHz) on bus A, B, C, and D I DVALID[A,B,C,D] LVDS input used to start write sequence for bus A, B, C, and D I ROWMD(1:0) DMD row address and row counter control I ROWAD(10:0) DMD row address pointer I BLK_AD(3:0) DMD mirror block address pointer I BLK_MD(1:0) DMD mirror block reset and clear command modes I PWR_FLOAT Used to float DMD mirrors before complete loss of power I DMD_TYPE(3:0) DMD type in use O RST_ACTIVE Indicates DMD mirror reset in progress O INIT_ACTIVE Initialization in progress. O VLED0 System “heartbeat” signal O VLED1 Denotes initialization complete O 8.3.4.1.1.2 Initialization The INIT_ACTIVE (Table 2) signal indicates that the DLP9500, DLPA200s, and DLPC410 are in an initialization state after power is applied. During this initialization period, the DLPC410 is initializing the DLP9500 and DLPA200s by setting all internal registers to their correct states. When this signal goes low, the system has completed initialization. System initialization takes approximately 220 ms to complete. Data and command write cycles should not be asserted during the initialization. During initialization the user must send a training pattern to the DLPC410 on all data and DVALID lines to correctly align the data inputs to the data clock. For more information, see the interface training pattern information in the DLPC410 data sheet. 8.3.4.1.1.3 DMD Device Detection The DLPC410 automatically detects the DMD type and device ID. DMD_TYPE (Table 2) is an output from the DLPC410 that contains the DMD information. 8.3.4.1.1.4 Power Down To ensure long term reliability of the DLP9500, a shutdown procedure must be executed. Prior to power removal, assert the PWR_FLOAT (Table 2) signal and allow approximately 300 µs for the procedure to complete. This procedure assures the mirrors are in a flat state. 8.3.4.1.2 DLPC410 to DMD Interface 8.3.4.1.2.1 DLPC410 to DMD IO Description Table 3 lists the available controls and status pin names and their corresponding signal type, along with a brief functional description. Table 3. DLPC410 to DMD I/O Pin Descriptions PIN NAME DESCRIPTION I/O DDC_DOUT_[A,B,C,D](15:0) LVDS DDR output to DMD data bus A,B,C,D (15:0) O DDC_DCLKOUT_[A,B,C,D] LVDS output to DMD data clock A,B,C,D O DDC_SCTRL_[A,B,C,D] LVDS DDR output to DMD data control A,B,C,D O Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 27 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com 8.3.4.1.2.2 Data Flow Figure 9 shows the data traffic through the DLPC410. Special considerations are necessary when laying out the DLPC410 to allow best signal flow. LVDS BUS A sDIN_A(15:0) sDCLK_A sDVALID_A LVDS BUS B sDIN_B(15:0) sDCLK_B sDVALID_B LVDS BUS D LVDS BUS C sDIN_D(15:0) sDCLK_D sDVALID_D sDIN_C(15:0) sDCLK_C sDVALID_C DLPC410 LVDS BUS D LVDS BUS A sDOUT_D(15:0) sDCLKOUT_D sSCTRL_D sDOUT_A(15:0) sDCLKOUT_A sSCTRL_A LVDS BUS C sDOUT_C(15:0) sDCLKOUT_C sSCTRL_C LVDS BUS B sDIN_B(15:0) sDCLK_B sDVALID_B Figure 9. DLPC410 Data Flow Four LVDS buses transfer the data from the user to the DLPC410. Each bus has its data clock that is input edge aligned with the data (DCLK). Each bus also has its own validation signal that qualifies the data input to the DLPC410 (DVALID). Output LVDS buses transfer data from the DLPC410 to the DMD. Output buses LVDS C and LVDS D are used in addition to LVDS A and LVDS B with the DLP9500. 8.3.4.1.3 DLPC410 to DLPA200 Interface 8.3.4.1.3.1 DLPA200 Operation The DLPA200 DMD micromirror driver is a mixed-signal application-specific integrated circuit (ASIC) that combines the necessary high-voltage power supply generation and micromirror clocking pulse functions for a family of DMDs. The DLPA200 is programmable and controllable to meet all current and anticipated DMD requirements. The DLPA200 operates from a 12-V power supply input. For more detailed information on the DLPA200, see the DLPA200 data sheet. 28 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 8.3.4.1.3.2 DLPC410 to DLPA200 IO Description The serial communications port (SCP) is a full duplex, synchronous, character-oriented (byte) port that allows exchange of commands from the DLPC410 to the DLPA200s. DLPA200 SCP bus DLPC410 SCP bus DLPA200 Figure 10. Serial Port System Configuration Five signal lines are associated with the SCP bus: SCPEN, SCPCK, SCPDI, SCPDO, and IRQ. Table 4 lists the available controls and status pin names and their corresponding signal type, along with a brief functional description. Table 4. DLPC410 to DLPA200 I/O Pin Descriptions PIN NAME DESCRIPTION I/O A_SCPEN Active-low chip select for DLPA200 serial bus O A_STROBE DLPA200 control signal strobe O A_MODE(1:0) DLPA200 mode control O A_SEL(1:0) DLPA200 select control O A_ADDR(3:0) DLPA200 address control O B_SCPEN Active-low chip select for DLPA200 serial bus (2) O B_STROBE DLPA200 control signal strobe (2) O B_MODE(1:0) DLPA200 mode control O B_SEL(1:0) DLPA200 select control O B_ADDR(3:0) DLPA200 address control O The DLPA200 provides a variety of output options to the DMD by selecting logic control inputs: MODE[1:0], SEL[1:0] and reset group address A[3:0] (Table 4). The MODE[1:0] input determines whether a single output, two outputs, four outputs, or all outputs, will be selected. Output levels (VBIAS, VOFFSET, or VRESET) are selected by SEL[1:0] pins. Selected outputs are tri-stated on the rising edge of the STROBE signal and latched to the selected voltage level after a break-before-make delay. Outputs will remain latched at the last micromirror clocking pulse waveform level until the next micromirror clocking pulse waveform cycle. 8.3.4.1.4 DLPA200 to DLP9500 Interface 8.3.4.1.4.1 DLPA200 to DLP9500 Interface Overview The DLPA200 generates three voltages: VBIAS, VRESET, and VOFFSET that are supplied to the DMD MBRST lines in various sequences through the micromirror clocking pulse driver function. VOFFSET is also supplied directly to the DMD as DMDVCC2. A fourth DMD power supply, DMDVCC, is supplied directly to the DMD by regulators. The function of the micromirror clocking pulse driver is to switch selected outputs in patterns between the three voltage levels (VBIAS, VRESET and VOFFSET) to generate one of several micromirror clocking pulse waveforms. The order of these micromirror clocking pulse waveform events is controlled externally by the logic control inputs and timed by the STROBE signal. DLPC410 automatically detects the DMD type and then uses the DMD type to determine the appropriate micromirror clocking pulse waveform. Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 29 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com A direct micromirror clocking pulse operation causes a mirror to transition directly from one latched state to the next. The address must already be set up on the mirror electrodes when the micromirror clocking pulse is initiated. Where the desired mirror display period does not allow for time to set up the address, a micromirror clocking pulse with release can be performed. This operation allows the mirror to go to a relaxed state regardless of the address while a new address is set up, after which the mirror can be driven to a new latched state. A mirror in the relaxed state typically reflects light into a system collection aperture and can be thought of as off although the light is likely to be more than a mirror latched in the off state. System designers should carefully evaluate the impact of relaxed mirror conditions on optical performance. 8.3.5 Measurement Conditions The data sheet provides timing at the device pin. For output timing analysis, the tester pin electronics and its transmission line effects must be taken into account. Figure 11 shows an equivalent test load circuit for the output under test. The load capacitance value stated is only for characterization and measurement of AC timing signals. This load capacitance value does not indicate the maximum load the device is capable of driving. All rise and fall transition timing parameters are referenced to VIL MAX and VIH MIN for input clocks, VOL MAX and VOH MIN for output clocks. LOAD CIRCUIT RL From Output Under Test Tester Channel CL = 50 pF CL = 5 pF for Disable Time Figure 11. Test Load Circuit for AC Timing Measurements 30 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 Ill Inc um id in en at t io n www.ti.com Package Pin A1 Corner Ill Inc um id in en at t io n DLP9500 Two “On-State” Micromirrors For Reference t nt t Pa ide gh Inc on-Li ati min Illu t h h at nt ide ht P Inc n-Lig atio min Illu Projected-Light Path Two “Off-State” Micromirrors O gh Li eat th t S a ff- P a±b Flat-State ( “parked” ) Micromirror Position -a ± b Silicon Substrate “On-State” Micromirror Silicon Substrate “Off-State” Micromirror Figure 12. Micromirror Landed Positions and Light Paths Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 31 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com 8.4 Device Functional Modes The DLP9500 has only one functional mode; it is set to be highly optimized for low latency and high speed in generating mirror clocking pulses and timings. When operated with the DLPC410 controller in conjunction with the DLPA200 drivers, the DLP9500 can be operated in several display modes. The DLP9500 is loaded as 15 blocks of 72 rows each. The first 64 bits of pixel data and last 64 bits of pixel data for all rows are not visible. Below is a representation of how the image is loaded by the different micromirror clocking pulse modes. Figure 13, Figure 14, Figure 15, and Figure 16 show how the image is loaded by the different micromirror clocking pulse modes. There are four micromirror clocking pulse modes that determine which blocks are reset when a micromirror clocking pulse command is issued: • Single block mode • Dual block mode • Quad block mode • Global mode 8.4.1 Single Block Mode In single block mode, a single block can be loaded and reset in any order. After a block is loaded, it can be reset to transfer the information to the mechanical state of the mirrors. Figure 13. Single Block Mode 8.4.2 Dual Block Mode In dual block mode, reset blocks are paired together as follows (0-1), (2-3), (4-5), (6-7), (8-9), (10-11), (12-13), and (14). These pairs can be reset in any order. After data is loaded a pair can be reset to transfer the information to the mechanical state of the mirrors. Figure 14. Dual Block Mode 32 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 Device Functional Modes (continued) 8.4.3 Quad Block Mode In quad block mode, reset blocks are grouped together in fours as follows (0-3), (4-7), (8-11) and (12-14). Each quad group can be randomly addressed and reset. After a quad group is loaded, it can be reset to transfer the information to the mechanical state of the mirrors. Figure 15. Quad Block Mode 8.4.4 Global Block Mode In global mode, all reset blocks are grouped into a single group and reset together. The entire DMD must be loaded with the desired data before issuing a Global Reset to transfer the information to the mechanical state of the mirrors. Figure 16. Global Mode Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 33 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com 8.5 Window Characteristics and Optics NOTE TI assumes no responsibility for image quality artifacts or DMD failures caused by optical system operating conditions exceeding limits described previously. 8.5.1 Optical Interface and System Image Quality TI assumes no responsibility for end-equipment optical performance. Achieving the desired end-equipment optical performance involves making trade-offs between numerous component and system design parameters. Optimizing system optical performance and image quality strongly relate to optical system design parameter trades. Although it is not possible to anticipate every conceivable application, projector image quality and optical performance is contingent on compliance to the optical system operating conditions described in the following sections. 8.5.2 Numerical Aperture and Stray Light Control The angle defined by the numerical aperture of the illumination and projection optics at the DMD optical area should be the same. This angle should not exceed the nominal device mirror tilt angle unless appropriate apertures are added in the illumination, projection pupils, or both to block out flat-state and stray light from the projection lens. The mirror tilt angle defines DMD capability to separate the ON optical path from any other light path, including undesirable flat-state specular reflections from the DMD window, DMD border structures, or other system surfaces near the DMD such as prism or lens surfaces. If the numerical aperture exceeds the mirror tilt angle, or if the projection numerical aperture angle is more than two degrees larger than the illumination numerical aperture angle, objectionable artifacts in the display’s border and/or active area could occur. 8.5.3 Pupil Match TI recommends the exit pupil of the illumination is nominally centered within 2° (two degrees) of the entrance pupil of the projection optics. Misalignment of pupils can create objectionable artifacts in the display’s border and/or active area, which may require additional system apertures to control, especially if the numerical aperture of the system exceeds the pixel tilt angle. 8.5.4 Illumination Overfill The active area of the device is surrounded by an aperture on the inside DMD window surface that masks structures of the DMD device assembly from normal view. The aperture is sized to anticipate several optical operating conditions. Overfill light illuminating the window aperture can create artifacts from the edge of the window aperture opening and other surface anomalies that may be visible on the screen. The illumination optical system should be designed to limit light flux incident anywhere on the window aperture from exceeding approximately 10% of the average flux level in the active area. Depending on the optical architecture of a particular system, overfill light may have to be further reduced below the suggested 10% level to be acceptable. 34 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 8.6 Micromirror Array Temperature Calculation Achieving optimal DMD performance requires proper management of the maximum DMD case temperature, the maximum temperature of any individual micromirror in the active array, the maximum temperature of the window aperture, and the temperature gradient between case temperature and the predicted micromirror array temperature (see Figure 17). See the Recommended Operating Conditions for applicable temperature limits. 8.6.1 Package Thermal Resistance The DMD is designed to conduct absorbed and dissipated heat to the back of the type A package where it can be removed by an appropriate heat sink. The heat sink and cooling system must be capable of maintaining the package within the specified operational temperatures, refer to Figure 17. The total heat load on the DMD is typically driven by the incident light absorbed by the active area; although other contributions include light energy absorbed by the window aperture and electrical power dissipation of the array. 8.6.2 Case Temperature The temperature of the DMD case can be measured directly. For consistency, thermal test point locations 1, 2, and 3 are defined, as shown in Figure 17. 21.08 Figure 17. Thermal Test Point Location Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 35 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com Micromirror Array Temperature Calculation (continued) 8.6.3 Micromirror Array Temperature Calculation Micromirror array temperature cannot be measured directly; therefore, it must be computed analytically from measurement points (Figure 17), the package thermal resistance, the electrical power, and the illumination heat load. The relationship between micromirror array temperature and the case temperature are provided by Equation 1 and Equation 2: TArray = T Ceramic + (QArray × RArray-To-Ceramic) (1) QArray = QELE + QILL where • • • • • • TArray = Computed micromirror array temperature (°C) TCeramic = Ceramic temperature (°C) (TP1 location Figure 17) QArray = Total DMD array power (electrical + absorbed) (measured in Watts) RArray-To-Ceramic = Thermal resistance of DMD package from array to TP1 (°C/W) (see Package Thermal Resistance) QELE = Nominal electrical power (W) QILL = Absorbed illumination energy (W) (2) An example calculation is provided based on a traditional DLP video projection system. The electrical power dissipation of the DMD is variable and depends on the voltages, data rates, and operating frequencies. The nominal electrical power dissipation used in the calculation is 4.4 W. Thus, QELE = 4.4 W. The absorbed power from the illumination source is variable and depends on the operating state of the mirrors and the intensity of the light source. Based on modeling and measured data from DLP projection system: QILL = CL2W × SL where • • • • CL2W is a lumens to watts constant and can be estimated at 0.00274 W/lm SL = Screen lumens nominally measured to be 2000 lm QArray = 4.4 + (0.00274 × 2000) = 9.88 W, estimated total power on micromirror array TCeramic = 55°C, assumed system measurement (3) Finally, TArray (micromirror active array temperature) is: TArray= 55°C + (9.88 W × 0.5°C/W) = 59.9°C 36 Submit Documentation Feedback (4) Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 8.7 Micromirror Landed-On and Landed-Off Duty Cycle 8.7.1 Definition of Micromirror Landed-On/Landed-Off Duty Cycle The micromirror landed-on/landed-off duty cycle (landed duty cycle) denotes the amount of time (as a percentage) that an individual micromirror is landed in the On–state versus the amount of time the same micromirror is landed in the Off–state. As an example, a landed duty cycle of 100/0 indicates that the referenced pixel is in the On-state 100% of the time (and in the Off-state 0% of the time); whereas 0/100 would indicate that the pixel is in the Off-state 100% of the time. Likewise, 50/50 indicates that the pixel is On 50% of the time and Off 50% of the time. Note that when assessing landed duty cycle, the time spent switching from one state (ON or OFF) to the other state (OFF or ON) is considered negligible and is thus ignored. Because a micromirror can only be landed in one state or the other (on or off), the two numbers (percentages) always add to 100. 8.7.2 Landed Duty Cycle and Useful Life of the DMD Knowing the long-term average landed duty cycle (of the end product or application) is important because subjecting all (or a portion) of the DMD’s micromirror array (also called the active array) to an asymmetric landed duty cycle for a prolonged period of time can reduce the usable life of the DMD. Note that it is the symmetry/asymmetry of the landed duty cycle that is of relevance. The symmetry of the landed duty cycle is determined by how close the two numbers (percentages) are to being equal. For example, a landed duty cycle of 50/50 is perfectly symmetrical whereas a landed duty cycle of 100/0 or 0/100 is perfectly asymmetrical. 8.7.3 Landed Duty Cycle and Operational DMD Temperature Operational DMD temperature and landed duty cycle interact to affect the usable life of the DMD, and this interaction can be exploited to reduce the impact that an asymmetrical landed duty cycle has on the DMD’s usable life. This is quantified in the derating curve shown in Figure 7. The importance of this curve is that: • All points along this curve represent the same usable life. • All points above this curve represent lower usable life (and the further away from the curve, the lower the usable life). • All points below this curve represent higher usable life (and the further away from the curve, the higher the usable life). In practice, this curve specifies the maximum operating DMD temperature that the DMD should be operated at for a give long-term average landed duty. 8.7.4 Estimating the Long-Term Average Landed Duty Cycle of a Product or Application During a given period of time, the landed duty cycle of a given pixel follows from the image content being displayed by that pixel. For example, in the simplest case, when displaying pure-white on a given pixel for a given time period, that pixel will experience a 100/0 landed duty cycle during that time period. Likewise, when displaying pure-black, the pixel will experience a 0/100 landed duty cycle. Between the two extremes (ignoring for the moment color and any image processing that may be applied to an incoming image), the landed duty cycle tracks one-to-one with the gray scale value, as shown in Table 5. Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 37 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com Table 5. Grayscale Value and Landed Duty Cycle GRAYSCALE VALUE LANDED DUTY CYCLE 0% 0/100 10% 10/90 20% 20/80 30% 30/70 40% 40/60 50% 50/50 60% 60/40 70% 70/30 80% 80/20 90% 90/10 100% 100/0 Accounting for color rendition (but still ignoring image processing) requires knowing both the color intensity (from 0% to 100%) for each constituent primary color (red, green, and/or blue) for the given pixel as well as the color cycle time for each primary color, where “color cycle time” is the total percentage of the frame time that a given primary must be displayed to achieve the desired white point. During a given period of time, the landed duty cycle of a given pixel can be calculated as follows: Landed Duty Cycle = (Red_Cycle_% × Red_Scale_Value) + (Green_Cycle_% × Green_Scale_Value) + (Blue_Cycle_% × Blue_Scale_Value) where: Red_Cycle_%, Green_Cycle_%, and Blue_Cycle_%, represent the percentage of the frame time that Red, Green, and Blue are displayed (respectively) to achieve the desired white point. For example, assume that the red, green and blue color cycle times are 50%, 20%, and 30% respectively (to achieve the desired white point), then the landed duty for various combinations of red, green, blue color intensities would be as shown in Table 6. Table 6. Example Landed Duty Cycle for Full-Color 38 RED CYCLE PERCENTAGE 50% GREEN CYCLE PERCENTAGE 20% BLUE CYCLE PERCENTAGE 30% RED SCALE VALUE GREEN SCALE VALUE BLUE SCALE VALUE 0% 0% 0% 0/100 100% 0% 0% 50/50 0% 100% 0% 20/80 0% 0% 100% 30/70 12% 0% 0% 6/94 0% 35% 0% 7/93 0% 0% 60% 18/82 100% 100% 0% 70/30 LANDED DUTY CYCLE 0% 100% 100% 50/50 100% 0% 100% 80/20 12% 35% 0% 13/87 0% 35% 60% 25/75 12% 0% 60% 24/76 100% 100% 100% 100/0 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 9 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 9.1 Application Information The DLP9500 devices must be coupled with the DLPC410 controller to provide a reliable solution for many different applications. The DMDs are spatial light modulators which reflect incoming light from an illumination source to one of two directions, with the primary direction being into a projection collection optic. Each application is derived primarily from the optical architecture of the system and the format of the data coming into the DLPC410. Applications of interest include 3D printing, lithography, medical systems, and compressive sensing. Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 39 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com 9.2 Typical Application A typical embedded system application using the DLPC410 controller and DLP9500 is shown in Figure 18. In this configuration, the DLPC410 controller supports input from an FPGA. The FPGA sends low-level data to the controller, enabling the system to be highly optimized for low latency and high speed. OPTICAL SENSOR LED DRIVERS (CAMERA) LEDS OPTICS LED SENSORS USER INTERFACE LVDS BUS (A,B,[C,D]) LVDS BUS (A,B,[C,D]) DDC_DCLK, DVALID, DDC_DIN(15:0) DDC_DCLKOUT, DDCSCTRL, DDC_DOUT(15:0) SCP BUS ROW and BLOCK SIGNALS SCPCLK, SCPDO, SCPDI, DMD_SCPENZ, A_SCPENZ, B_SCPENZ ROWMD(1:0), ROWAD(10:0), BLKMD(1:0), BLKAD(3:0), RST2BLKZ CONNECTIVITY (USB, ETHERNET, ETC.) CONTROL SIGNALS COMP_DATA, NS_FLIP, WDT_ENBLZ, PWR_FLOAT USER - MAIN PROCESSOR / FPGA DLPA200 CONTROL A_MODE(1:0), A_SEL(1:0), A_ADDR(3:0), OEZ, INIT DLPC410 INFO SIGNALS RST_ACTIVE, INIT_ACTIVE, ECP2_FINISHED, DMD_TYPE(3:0), DDC_VERSION(2:0) MBRST1_(15:0) DLP9500 DLPA200 A DLPC410 PGM SIGNALS VOLATILE and NON-VOLATILE STORAGE DLPR410 PROM_CCK_DDC, PROGB_DDC, PROM_DO_DDC, DONE_DDC, INTB_DDC DLPA200 CONTROL B_MODE(1:0), B_SEL(1:0), B_ADDR(3:0), OEZ, INIT JTAG ARSTZ CLKIN_R OSC 50 Mhz ~ MBRST2_(15:0) DLPA200 B VLED0 VLED1 DMD_RESET POWER MANAGMENT Figure 18. DLPC410 and DLP9500 Embedded Example Block Diagram 40 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 9.2.1 Design Requirements All applications using the DLP9500 1080p chipset require both the controller and the DMD components for operation. The system also requires an external parallel flash memory device loaded with the DLPC410 configuration and support firmware. The chipset has several system interfaces and requires some support circuitry. The following interfaces and support circuitry are required: • DLPC410 system interfaces: – Control interface – Trigger interface – Input data interface – Illumination interface – Reference clock – Program interface • DLP9500 interfaces: – DLPC410 to DLP9500 digital data – DLPC410 to DLP9500 control interface – DLPC410 to DLP9500 micromirror reset control interface – DLPC410 to DLPA200 micromirror driver – DLPA200 to DLP9500 micromirror reset 9.2.1.1 Device Description The DLP9500 1080p chipset offers developers a convenient way to design a wide variety of industrial, medical, telecom and advanced display applications by delivering maximum flexibility in formatting data, sequencing data, and light patterns. The DLP9500 1080p chipset includes the following four components: DMD digital controller (DLPC410), EEPROM (DLPR410), DMD micromirror driver (DLPA200), and a DMD (DLP9500). DLPC410 DMD digital controller • Provides high speed 2XLVDS data and control interface to the user. • Drives mirror clocking pulse and timing information to the DLPA200. • Supports random row addressing. • Controls illumination DLPR410 EEPROM • Contains startup configuration information for the DLPC410 DLPA200 DMD micromirror driver • Generates micromirror clocking pulse control (sometimes referred to as a reset) of 15 banks of DMD mirrors. (Two are required for the DLP9500.) DLP9500 DMD • Steers light in two digital positions (+12° and –12°) using 1920 × 1080 micromirror array of aluminum mirrors. Table 7. DLP DLP9500 Chipset Configurations QUANTITY TI PART 1 DLP9500 0.95 1080p Type A digital micromirror device (DMD) DESCRIPTION 1 DLPC410 DLP Discovery 4100 DMD controller 1 DLPR410 DLP Discovery 4100 configuration PROM 2 DLPA200 DMD micromirror driver Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 41 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com Reliable function and operation of DLP9500 1080p chipsets require the components be used in conjunction with each other. This document describes the proper integration and use of the DLP9500 1080p chipset components. The DLP9500 1080p chipset can be combined with a user programmable application FPGA (not included) to create high performance systems. 9.2.2 Detailed Design Procedure The DLP9500 DMD is well suited for visible light applications requiring fast, spatially programmable light patterns using the micromirror array. See the block diagram in Figure 8 to see the connections between the DLP9500 DMD, the DLPC410 digital controller, the DLPR410 EEPROM, and the DLPA200 DMD micromirror drivers. An example application block diagram can be found in Figure 18. Layout guidelines should be followed for reliability. 10 Power Supply Recommendations 10.1 Power-Up Sequence (Handled by the DLPC410) The sequence of events for DMD system power-up is: 1. Apply logic supply voltages to the DLPA200 and to the DMD according to DMD specifications. 2. Place DLPA200 drivers into high impedance states. 3. Turn on DLPA200 bias, offset, or reset supplies according to driver specifications. 4. After all supply voltages are assured to be within the limits specified and with all micromirror clocking pulse operations logically suspended, enable all drivers to either VOFFSET or VBIAS level. 5. Begin micromirror clocking pulse operations. 10.2 DMD Power-Up and Power-Down Procedures Failure to adhere to the prescribed power-up and power-down procedures may affect device reliability. The DLP9500 power-up and power-down procedures are defined by the DLPC410 data sheet (DLPS024). These procedures must be followed to ensure reliable operation of the device. 42 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 11 Layout 11.1 Layout Guidelines The DLP9500 is part of a chipset that is controlled by the DLPC410 in conjunction with the DLPA200. These guidelines are targeted at designing a PCB board with these components. 11.1.1 Impedance Requirements Signals should be routed to have a matched impedance of 50 Ω ±10% except for LVDS differential pairs (DMD_DAT_Xnn, DMD_DCKL_Xn, and DMD_SCTRL_Xn) which should be matched to 100 Ω ±10% across each pair. 11.1.2 PCB Signal Routing When designing a PCB board for the DLP9500 controlled by the DLPC410 in conjunction with the DLPA200s, the following are recommended: Signal trace corners should be no sharper than 45°. Adjacent signal layers should have the predominate traces routed orthogonal to each other. TI recommends that critical signals be hand routed in the following order: DDR2 Memory, DMD (LVDS signals), then DLPA200 signals. TI does not recommend signal routing on power or ground planes. TI does not recommend ground plane slots. High speed signal traces should not cross over slots in adjacent power and/or ground planes. Table 8. Important Signal Trace Constraints SIGNAL CONSTRAINTS LVDS (DMD_DAT_xnn, DMD_DCKL_xn, and DMD_SCTRL_xn) P-to-N data, clock, and SCTRL: <10 mils (0.25 mm); Pair-to-pair <10 mils (0.25 mm); Bundle-to-bundle <2000 mils (50 mm, for example DMD_DAT_Ann to DMD_DAT_Bnn) Trace width: 4 mil (0.1 mm) Trace spacing: In ball field – 4 mil (0.11 mm); PCB etch – 14 mil (0.36 mm) Maximum recommended trace length <6 inches (150 mm) Table 9. Power Trace Widths and Spacing SIGNAL NAME MINIMUM TRACE WIDTH MINIMUM TRACE SPACING GND Maximize 5 mil (0.13 mm) VCC, VCC2 20 mil (0.51 mm) 10 mil (0.25 mm) MBRST[14:0] 11 mil (0.28 mm) 15 mil (0.38 mm) LAYOUT REQUIREMENTS Maximize trace width to connecting pin as a minimum 11.1.3 Fiducials Fiducials for automatic component insertion should be 0.05-inch copper with a 0.1-inch cutout (antipad). Fiducials for optical auto insertion are placed on three corners of both sides of the PCB. 11.1.4 PCB Layout Guidelines A target impedance of 50 Ω for single ended signals and 100 Ω between LVDS signals is specified for all signal layers. 11.1.4.1 DMD Interface The digital interface from the DLPC410 to the DMD are LVDS signals that run at clock rates up to 400 MHz. Data is clocked into the DMD on both the rising and falling edge of the clock, so the data rate is 800 MHz. The LVDS signals should have 100 Ω differential impedance. The differential signals should be matched but kept as short as possible. Parallel termination at the LVDS receiver is in the DMD; therefore, on board termination is not necessary. Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 43 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com 11.1.4.1.1 Trace Length Matching The DLPC410 DMD data signals require precise length matching. Differential signals should have impedance of 100Ω (with 5% tolerance). It is important that the propagation delays are matched. The maximum differential pair uncoupled length is 100 mils with a relative propagation delay of ±25 mil between the p and n. Matching all signals exactly will maximize the channel margin. The signal path through all boards, flex cables and internal DMD routing must be considered in this calculation. 11.1.4.2 DLP9500 Decoupling General decoupling capacitors for the DLP9500 should be distributed around the PCB and placed to minimize the distance from IC voltage and ground pads. Each decoupling capacitor (0.1 µF recommended) should have vias directly to the ground and power planes. Via sharing between components (discreet or integrated) is discouraged. The power and ground pads of the DLP9500 should be tied to the voltage and ground planes with their own vias. 11.1.4.2.1 Decoupling Capacitors Decoupling capacitors should be placed to minimize the distance from the decoupling capacitor to the supply and ground pin of the component. TI recommends that the placement of and routing for the decoupling capacitors meet the following guidelines: • The supply voltage pin of the capacitor should be located close to the device supply voltage pin or pins. The decoupling capacitor should have vias to ground and voltage planes. The device can be connected directly to the decoupling capacitor (no via) if the trace length is less than 0.1 inch. Otherwise, the component should be tied to the voltage or ground plane through separate vias. • The trace lengths of the voltage and ground connections for decoupling capacitors and components should be less than 0.1 inch to minimize inductance. • The trace width of the power and ground connection to decoupling capacitors and components should be as wide as possible to minimize inductance. • Connecting decoupling capacitors to ground and power planes through multiple vias can reduce inductance and improve noise performance. • Decoupling performance can be improved by using low ESR and low ESL capacitors. 11.1.4.3 VCC and VCC2 The VCC pins of the DMD should be connected directly to the DMD VCC plane. Decoupling for the VCC should be distributed around the DMD and placed to minimize the distance from the voltage and ground pads. Each decoupling capacitor should have vias directly connected to the ground and power planes. The VCC and GND pads of the DMD should be tied to the VCC and ground planes with their own vias. The VCC2 voltage can be routed to the DMD as a trace. Decoupling capacitors should be placed to minimize the distance from the DMD’s VCC2 and ground pads. Using wide etch from the decoupling capacitors to the DMD connection will reduce inductance and improve decoupling performance. 11.1.4.4 DMD Layout See the respective sections in this data sheet for package dimensions, timing and pin out information. 11.1.4.5 DLPA200 The DLPA200 generates the micromirror clocking pulses for the DMD. The DMD-drive outputs from the DLPA200 (MBRST[29:0] should be routed with minimum trace width of 11 mil and a minimum spacing of 15 mil. The VCC and VCC2 traces from the output capacitors to the DLPA200 should also be routed with a minimum trace width and spacing of 11 mil and 15 mil, respectively. See the DLPA200 customer data sheet DLPS015 for mechanical package and layout information. 44 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 11.2 Layout Example For LVDS (and other differential signal) pairs and groups, it is important to match trace lengths. In the area of the dashed lines, Figure 19 shows correct matching of signal pair lengths with serpentine sections to maintain the correct impedance. Figure 19. Mitering LVDS Traces to Match Lengths Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 45 DLP9500 DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 www.ti.com 12 Device and Documentation Support 12.1 Device Support 12.1.1 Device Nomenclature Figure 20 provides a legend of reading the complete device name for any DLP device. DLP9500 FLN Package Type Device Descriptor Figure 20. Device Nomenclature 12.1.2 Device Marking Figure 21 shows the device marking fields. TI Internal Numbering 2-Dimensional Matrix Code DMD Part Number (DMD Part Number and Serial Number) Part 2 of Serial Number Part 1 of Serial Number (7 characters) (7 characters) TI Internal Numbering Figure 21. DLP9500 Device Marking 12.2 Documentation Support 12.2.1 Related Documentation The following documents contain additional information related to the use of the DLP9500 device. • DLPC410 digital controller data sheet • DLPA200 DMD micromirror driver data sheet • DLPR410 EEPROM data sheet 12.3 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support. 46 Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 DLP9500 www.ti.com DLPS025C – AUGUST 2012 – REVISED SEPTEMBER 2015 12.4 Trademarks Discovery, E2E are trademarks of Texas Instruments. DLP is a registered trademark of Texas Instruments. All other trademarks are the property of their respective owners. 12.5 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 12.6 Glossary SLYZ022 — TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 13 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. Submit Documentation Feedback Copyright © 2012–2015, Texas Instruments Incorporated Product Folder Links: DLP9500 47 PACKAGE OPTION ADDENDUM www.ti.com 23-Dec-2015 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) DLP9500BFLN ACTIVE LCCC FLN 355 3 TBD Call TI Call TI DLP9500FLN NRND LCCC FLN 355 3 TBD Call TI Call TI Op Temp (°C) Device Marking (4/5) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 23-Dec-2015 In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2015, Texas Instruments Incorporated