MURF520 THRU MURF560 R GLASS PASSIVATED SUPER FAST RECTIFIER Reverse Voltage - 200 -600 Volts Forward Current - 5.0Amperes S E M I C O N D U C T O R FEATURES ITO-220AC Plastic package has Underwriters Laboratory Flammability Classification 94V-0 Fast switching for high efficiency Low forward voltage drop Single rectifier construction High surge capability For use in low voltage ,high frequency inverters, JF free wheeling ,and polarity protection applications MURF560 High temperature soldering guaranteed:260°C/10 seconds, 0.25"(6.35mm)from case 0.177(4.50) 0.138(3.50) Component in accordance to RoHS 2011/65/EU 0.187(4.75) 0.167(4.25) 0.140(3.55) 0.410(10.42) 0.388(9.85) 0.128(3.25) DIA 0.130(3.31) 0.110(2.81) 0.111(2.83) 0.101(2.57) 1 PIN 0.272(6.90) 0.256(6.50) 2 1.161(29.50) 0.136(3.45) 1.083(27.50) 0.551(14.00) 0.102(2.60) 0.496(12.60) 0.056(1.43) 0.043(1.10) 0.029(0.73) 0.019(0.47) MECHANICAL DATA 0.208(5.28) 0.029(0.73) 0.192(4.88) 0.019(0.47) Case: JEDEC ITO-220AC molded plastic body Terminals: Lead solderable per MIL-STD-750,method 2026 Polarity: As marked Mounting Position: Any Dimensions in inches and (millimeters) Weight: 0.08ounce, 2.24 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS (Ratings at 25°C ambient temperature unless otherwise specified ,Single phase ,half wave ,resistive or inductive load. For capacitive load,derate by 20%.) Symbols MURF520 MURF540 MURF560 Units Maximum DC blocking voltage VRRM VRMS VDC Maximum average forward rectified current(see Fig.1) I(AV) 5.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 150.0 75 Amps Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum instantaneous forward voltage at 5.0 A(Note 1 ) Maximum instantaneous reverse current at rated DC blocking voltage(Note 1) T A =25°C TA =125°C Maximum Reverse Recovery Time (Note 2) Typical thermal resistance (Note 3) Operating junction temperature range Storage temperature range VF 200 400 600 140 280 420 200 400 600 0.975 5 IR 500 Trr R 1.3 JC TJ TSTG 1.7 Volts Volts Volts Volts uA 35 ns 3.0 °C/W -40 to+150 °C -40 to+150 °C Notes: 1. Pulse test: 300μs pulse width,1% duty cycle 2. Reverse recovery test conditions IF=0.5A,IR=1.0A, Irr=0.5A 3. Thermal resistance from junction to case JINAN JINGHENG ELECTRONICS CO., LTD. 9-12 HTTP://WWW.JINGHENGGROUP.COM RATINGS AND CHARACTERISTIC CURVES MURF520 THRU MURF560 FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT(AMPERES) AVERAGE FORWARD CURRENT AMPERES FIG.1-FORWARD CURRENT DERATING CURVE 6 5 RESISTIVE OR INDUCTVE LOAD 4 3 2 1 0 0 20 40 60 80 100 120 180 150 LEAD TEMPERATURE (°C) FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 105 8.3ms Single Half Sine-Wave (JEDEC Method) 90 75 60 45 30 15 0 1 2 20 50 100 FIG.4-TYPICAL REVERSE CHARACTERISTICS 20 50 10 200V 400V 10 INSTANTANEOUS REVERSE CURRENT (UA) INSTANTANEOUS FORWARD CURRENT( AMPERES) 10 5 NUMBER OF CYCLES AT 60Hz 600V PULSE WIDTH=300μS 1% DUTY CYCLE 1 0.1 TJ=100°C 1 TJ=25°C 0.1 0.01 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 0.001 INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE% FIG.6-TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE, C/ W FIG.5-TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE(pF) 400 TJ=25°C f=1.0MHZ Vsig=50mVp-p 100 10 0.1 1 10 100 REVERSE VOLTAGE. VOLTS JINAN JINGHENG ELECTRONICS CO., LTD. 100 10 1 0.1 0.01 0.1 1 10 100 T, PULSE DURATION ,sec. 9-13 HTTP://WWW.JINGHENGGROUP.COM