B Electrical Capacity Resistive Load: Inductive Load: Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Angle of Throw: Housing: Movable Contacts: Stationary Contacts: Base: Common Terminal: End Terminals: Lamp Terminals: Tilt Tactiles Slides Rotaries Keylocks Materials & Finishes Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: Installation Touch Cap Installation Force: SolderingTime & Temperature: Standards & Certifications UL: 10A @ 125V AC, 6A @ 250V AC, or 6A @ 30V DC 5A @ 125V AC (P. F. @ .60) 10 milliohms maximum 200 megohms minimum @ 500V DC 1,500V AC minimum for 1 minute minimum 30,000 operations minimum 10,000 operations minimum 11.77N for maintained & 17.65N for momentary 34° Steel with chrome plating Silver clad copper with silver plating Copper with silver plating Melamine Copper with tin plating Brass with tin plating Phosphor bronze with nickel plating –20°C through +50°C (–4°F through +122°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 3 right angled directions, with 3 shocks in each direction) 19.61N (4.41 lbf) Manual Soldering: See Profile A in Supplement section. File No. E44145 - Recognized only when ordered with marking on switch. Add “/U” or “/CUL” before first dash in part number to order UL recognized switch. All models recognized at 10A @ 125V AC & 6A @ 250V AC Supplement Accessories Indicators Power-Rated Snap-in Rockers General Specifications Programmable Illuminated PB Pushbuttons Rockers Toggles Series LW B56 www.nkkswitches.com Distinctive Characteristics B Pushbuttons Each half of the rocker face is distinctly illuminated due to partitioned rocker construction and dual lamps. Rockers Toggles Series LW Power-Rated Snap-in Rockers Programmable Illuminated PB Numerous lighting effects achievable by using white or clear rocker with colored filters or lamp covers, plus using different colors on each side of rocker. Snap-in mounting allows fast, easy installation of switch into panel. Rotaries Keylocks Stainless steel retaining clips provide secure mounting over a wide range of panel thicknesses. Slides Dual incandescent or neon lamps operate independently of each other. Tactiles Front panel relamping. Tilt Stationary lamp sockets are independent of rocker actuation, protecting lamps from damage due to shock and vibration. Touch Switch contacts are rated at 10 amps 125V AC which makes these devices well-suited for various power switching applications. Supplement Accessories Indicators Actual Size www.nkkswitches.com B57 Series LW Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles Power-Rated Snap-in Rockers TYPICAL SWITCH ORDERING EXAMPLE 2 LW31 B 2 Pole 2 4 C DPDT Circuits 1 White without filters or lamp covers 2 White with filters F A Lamp Cover/ Filter Colors For Down Position Rocker Caps 0 No Cover/Filter Lamp Cover Up Center Down 3 White with lamp covers C Red 2 ON NONE ON 4 Clear with filters D Amber 3 ON OFF ON F Green 5 ON NONE (ON) 8 (ON) OFF (ON) 9 ON OFF (ON) Filter Lamp Cover/ Filter Colors For Up Position ( ) = Momentary 0 No Cover/Filter Lamp Cover Lamps Incandescent E 6-volt F 12-volt H 18-volt K 24-volt L 28-volt Neon N 110-volt Nonilluminated Touch 0 No Lamp B White C Red D Amber E Yellow C Red F Green D Amber G Blue F Green Filter Not suitable with green & blue Tilt H B White C Red D Amber E Yellow F Green G Blue Bezel No Code IMPORTANT: Switches are supplied without UL & cULus marking unless specified. UL & cULus recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on General Specifications page. Indicators DESCRIPTION FOR TYPICAL ORDERING EXAMPLE LW3122-H4CF-A Accessories Clear Rocker with Red Filter in Up Position & Green Filter in Down Position Supplement DPDT ON-NONE-ON Circuit B58 www.nkkswitches.com 18-volt Incandescent Lamp Black Bezel No Bezel A Black B White C Red D Amber E Yellow F Green G Blue H Gray Series LW Toggles Power-Rated Snap-in Rockers POLES & CIRCUITS DP LW3122 LW3123 LW3125 LW3128 LW3129 Up Center Down ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) Up Center Down Notes: Terminal numbers are not actually on switch. Lamp circuit is isolated and requires an external power source. DPDT 2-3 5-6 OPEN 2 2-1 5-4 3 (COM) 1 5 6 4 L1 L2 L3 L4 LAMP CODES & SPECIFICATIONS Electrical specifications are determined at a basic temperature of 25°C. Lamp circuit is independent of switch operation. For dimension drawing of lamps see Accessories & Hardware section. For neon, if the source voltage is greater than rated voltage, a ballast resistor is required. The ballast resistor calculation and more lamp detail are shown in the Supplement section. Neon not for use with green lamp cover or blue and green filters. E F H K L N Voltage V 6V AC 12V AC 18V AC 24V AC 28V AC 110V AC Current I 80mA 50mA 35mA 25mA 22mA 1.5mA .159 .215 .398 .215 .247 NA MSCP Keylocks Incandescent & Neon Lamps for Solid & Design Caps Hours 2,000 Average 15,000 Average Ambient Temperature Range –20°C ~ +50°C –20°C ~ +50°C Endurance Slides AT602 AT602N Incandescent Neon Recommended Resistor for Neon: 33K ohms for 110V AC; 100K ohms for 220V AC No Lamp Code 0 indicates that no lamp is used. Tactiles 0 T-11⁄2 Pilot Slide Base ROCKER CAPS, LAMP COVER & FILTER 2 AT420B White Rocker with Filters 3 AT420B White Rocker with Lamp Covers 4 AT420J Clear Rocker with Filters Tilt AT420B White Rocker without Filters or Lamp Covers Touch 1 B Rockers Model Pushbuttons Pole Throw & Power/Lamp Schematics Programmable Illuminated PB Connected Terminals ( ) = Momentary Rotaries Rocker Position AT421 AT421 Rocker Cap Material: Polycarbonate Indicators AT416 Finish: Glossy Indicate the lamp cover or filter color desired in both the up and down positions. D Amber F Green Material: Silicon Rubber White Yellow C Red F Green D Amber G Blue www.nkkswitches.com Accessories Red AT421 Filter E Supplement AT416 Lamp Cover B C Material: Polycarbonate B59 Series LW Toggles Power-Rated Snap-in Rockers BEZEL & BEZEL COLORS Rockers AT206 Bezel & Color Codes B No Code Programmable Illuminated PB Pushbuttons A No Bezel Black (19.4) .764 (28.8) 1.134 B White D Amber F Green C Red E Yellow G Blue H (2.6) .102 Gray (41.0) 1.614 (24.0) .945 Material: Polycarbonate TYPICAL SWITCH DIMENSIONS Solder Lug • Without Bezel (2.5) .098 (1.2) Dia Typ .047 (27.6) 1.087 (36.0) 1.417 L1 (0.68) Typ .027 (2.0) x (2.6) Typ .079 x .102 (0.4) Typ .016 34° 4 1 L2 (30.0) 1.181 2 (32.0) 1.260 5 L3 (9.4) Typ .370 3 6 Rotaries Keylocks L4 (19.0) .748 (19.7) .774 (8.4) .331 (0.6) .024 (28.7) 1.130 (4.5) .177 (6.7) .264 (19.8) .780 (3.0) .118 Panel Thickness .039” ~ .157” (1.0mm ~ 4.0mm) Actuator in UP position LW3122-F4CF Solder Lug • With Bezel (1.2) Dia Typ .047 Slides (4.0) .157 (0.68) Typ .027 (2.0) x (2.6) Typ .079 x .102 (27.6) 1.087 Tactiles (28.8) 1.134 (0.4) Typ .016 34° (30.0) 1.181 L1 1 4 L2 5 2 (41.0) 1.614 (32.0) 1.260 L3 (9.4) Typ .370 3 6 L4 Tilt (19.0) .748 (10.0) .394 (27.1) 1.067 (19.8) .780 (24.0) .945 (3.0) .118 Panel Thickness .039” ~ .118” (1.0mm ~ 3.0mm) Actuator in UP position OPTIONAL ACCESSORY AT107 Lamp Extractor (5.0) Dia .197 Lamps can be changed without removing the switch from the panel. AT107 assists in removing lamps from the switch. Accessories Indicators Touch LW3122-F3CF-A (19.7) .774 (2.6) .102 (4.5) .177 (6.7) .264 (3.8) Dia .150 LEGENDS Supplement Inscriptions can be placed on the rocker or filter. Details regarding screen printing may be obtained from the factory. B60 www.nkkswitches.com (20.0) .787