MO-9150A 80-220 MHz High Performance Oscillator Applications Features • Any frequency between 80.000001 and 220 MHz accurate to 6 dp • CMOS compa ble output • Ultra low phase ji er: 0.5 ps (12 kHz to 20 MHz) • Industrial and extended commercial temperature ranges • Standard 4-pin packages: 2.5 x 2.0, 3.2 x 2.5, 5.0 x 3.2, 7.0 x 5.0 mm • Compu ng, storage, networking, telecom, industrial control • SATA, SAS, Ethernet, PCI Express, video, WiFi Performance SpecificaƟons Parameter and Condi ons Output Frequency Range Frequency Stability Symbol f F_stab First year Aging 10-year Aging Opera ng Temperature Range F_aging Supply Voltage Min. 80 -20 Typ. - Max. 220 +20 Unit MHz PPM T_use -50 -1.5 -5 -20 - +50 +1.5 +5 +70 PPM PPM PPM °C Vdd -40 1.71 1.8 +85 1.89 °C V 2.25 2.52 2.97 45 40 90% 2.5 2.8 3.3 34 30 1.5 - 2.75 3.08 3.63 36 33 31 30 70 10 55 60 2 - V V V mA mA mA mA μA μA % % ns Vdd 70% - 100 6 – – 1.5 2 0.6 10% 30% 250 10 115 10 2 3 1 Vdd Vdd Vdd kΩ ms ns ms ps ps ps Current Consump on Idd OE Disable Current I_OE Standby Current I_std Duty Cycle Rise/Fall Time Output Voltage High Output Voltage Low Input Voltage High Input Voltage Low Input Pull-up Impedance Startup Time OE Enable/Disable Time Resume Time RMS Period Ji er RMS Phase Ji er (random) DC Tr, Tf VOH VOL VIH VIL Z_in T_start T_oe T_resume T_ji T_phj Condi on Inclusive of Ini al tolerance at 25 °C, and varia ons over opera ng temperature, aging, supply voltage and load 25°C 25°C Extended Commercial Industrial Supply voltages between 2.5V and 3.3V are supported in increments of 0.1 V. Contact Vectron for guaranteed performance specs for supply voltages not specified in this table. No load condi on, f = 100 MHz, Vdd = 2.5V, 2.8V or 3.3V No load condi on, f = 100 MHz, Vdd = 1.8V Vdd = 2.5V, 2.8V or 3.3V, OE = GND, output is Weakly Pulled Down Vdd = 1.8 V. OE = GND, output is Weakly Pulled Down Vdd = 2.5V, 2.8V or 3.3V, ST = GND, output is Weakly Pulled Down Vdd = 1.8 V. ST = GND, output is Weakly Pulled Down f <= 165 MHz, all Vdds. f > 165 MHz, all Vdds. 15 pF load, 10% -90% Vdd OH = -7 mA, IOL = 7 mA, (Vdd = 3.3V) IOH = -4 mA, IOL = 4 mA, (Vdd = 2.8V, 2.5V) IOH = -2 mA, IOL = 2 mA, (Vdd = 1.8V) Pin 1, OE or ST Pin 1, OE or ST Measured from the me Vdd reaches its rated minimum value f = 220 MHz, For other frequencies, T_oe = 100 ns + 3 cycles Measured from the me ST pin crosses 50% threshold f = 156.25 MHz, Vdd = 2.5V, 2.8V or 3.3V f = 156.25 MHz, Vdd = 1.8V f = 156.25 MHz, Integra on bandwidth = 12 kHz to 20 MHz Page 1 of 5 Vectron Interna onal • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • h p://www.vectron.com Rev 1.2 Aug 2014 Timing Diagrams 90% Vdd, 2.5/2,8/3.3V devices Vdd 95% Vdd, 1.8V devices Vdd Pin 4 Voltage ST Voltage 50% Vdd T_start T_resume CLK Output T_start: Time to start from power-off (ST/OE Mode) CLK Output T_resume: Time to resume from standby (ST Mode Only) Typical Performance Page 2 of 5 Vectron Interna onal • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • h p://www.vectron.com Rev 1.2 Aug 2014 Outline Drawing / Packaging Package Outline & Dimensions (Unit: mm) Recommended Land PaƩern (Unit: mm) 2.7 x 2.4 x 0.75 mm (100% compatible with 2.5 x 2. 0 mm footprint) YXXXX 3.2 x 2.5 x 0.75 mm 2.2 3.2 ± 0.05 2.1 #3 0.9 #2 #1 0.9 0.75 ± 0.05 #2 1.2 #1 0.7 YXXXX #4 1.9 #3 2.5 ± 0.05 #4 1.4 5.0 x 3.2 x 0.75 mm 2.54 5.0 ± 0.05 2.39 #3 #2 2.2 1.6 #2 0.75 ± 0.05 #1 1.1 YXXXX #4 0.8 #3 3.2 ± 0.05 #4 #1 1.15 1.5 7.0 x 5.0 x 0.90 mm 5.08 2.6 0.90 ± 0.10 2.0 1.1 YXXXX 5.0 ± 0.05 7.0 ± 0.05 3.81 5.08 1.4 2.2 Top View Pin ConnecƟons Pin Symbol 1 OE/ ST Func onality Output Enable H or Open[*]: specified frequency output L: output is high impedance. Only output driver is disabled. Standby H or Open[3*: specified frequency output L: output is low (weak pull down). Device goes to sleep mode. Supply current reduces to I_std. 2 GND Power Electrical and case ground 3 OUT Output Oscillator output 4 VDD Power Power supply voltage OE/ST 1 4 VDD GND 2 3 OUT *A pull-up resistor of <10 kΩ between OE/ ST pin and Vdd is recommended in high noise environment Page 3 of 5 Vectron Interna onal • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • h p://www.vectron.com Rev 1.2 Aug 2014 Absolute Maximum RaƟngs and Test Compliance Maximum RaƟngs Parameter Min Max Unit Storage Temperature -65 150 °C VDD -0.5 4 V Electrosta c Discharge – 2000 V Soldering Temperature (follow standard Pb free soldering guidelines) – 260 °C Number of Program Writes – 1 NA Program Reten on over -40 to 125°C, Process, VDD (0 to 3.65V) 1,000+ – years Environmental Compliance Parameter Condi on/Test Method Mechanical Shock MIL-STD-883F, Method 2002 Mechanical Vibra on MIL-STD-883F, Method 2007 Temperature Cycle JESD22, Method A104 Solderability MIL-STD-883F, Method 2003 Moisture Sensi vity Level MSL1 @ 260°C Ordering InformaƟon MO - 9150A E - 4 F - E E - 156M250000 Product MO: MEMS XO Frequency Feature Pin E: Enable/Disable S: Standby Family 9150A: CMOS clock, 80-220MHz Temp Range J: -20/70°C E: -40/85°C Package 2: 4 pin 7.0mm x 5.0mm 4: 4 pin 5.0mm x 3.2mm 6: 4 pin 3.2mm x 2.5mm 8: 4 pin 2.5mm x 2.0mm compa ble Stability E: ±20ppm F: ±25ppm K: ±50ppm Supply Voltage E: +3.3 Vdc G: +2.8 Vdc H: +2.5 Vdc J: +1.8 Vdc Notes: 1. Contact factory for improved stabili es or addi onal product op ons. Not all op ons and codes are available at all frequencies. 2. Unless otherwise stated all values are valid a er warm-up me and refer to typical condi ons for supply voltage, frequency control voltage, load, temperature (25°C). 3. Subject to technical modifica on. 4. Contact factory for availability. Page 4 of 5 Vectron Interna onal • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • h p://www.vectron.com Rev 1.2 Aug 2014 Revision History Revision Change Summary Date 1.0 Product Release June 2013 1.1 Knowles logo and address change Feb 2014 1.2 Add ±20ppm temperature stability Aug 2014 For Additional Information, Please Contact USA: Europe: Asia: Vectron Interna onal 267 Lowell Road, Suite 102 Hudson, NH 03051 Tel: 1.888.328.7661 Fax: 1.888.329.8328 Vectron Interna onal Landstrasse, D-74924 Neckarbischofsheim, Germany Tel: +49 (0) 7268.801.100 Fax: +49 (0) 7268.801.282 68 Yin Cheng Road(C), 22nd Floor One Lu Jia Zui Pudong, Shanghai 200120, China Tel: +86 21 6194 6886 Fax: +86 21 6194 6699 Disclaimer Vectron Interna onal reserves the right to make changes to the product(s) and or informa on contained herein without no ce. No liability is assumed as a result of their use or applicaon. No rights under any patent accompany the sale of any such product(s) or informa on. Page 5 of 5 Vectron Interna onal • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • h p://www.vectron.com Rev 1.2 Aug 2014