FR201 - FR207-STR FAST RECOVERY RECTIFIER DIODES PRV : 50 - 1000 Volts Io : 2.0 Amperes D2 FEATURES : * * * * * * High current capability High surge current capability High reliability Low reverse current Low forward voltage drop Fast switching for high efficiency 1.00 (25.4) MIN. 0.161 (4.1) 0.154 (3.9) 0.284 (7.2) 0.268 (6.8) MECHANICAL DATA : 0.034 (0.86) 0.028 (0.71) * Case : D2 Molded plastic * Epoxy : UL94V-O rate flame retardant * Lead : Axial lead solderable per MIL-STD-202, Method 208 guaranteed * Polarity : Color band denotes cathode end * Mounting position : Any * Weight : 0.465 gram 1.00 (25.4) MIN. Dimensions in inches and ( millimeters ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. RATING SYMBOL FR201 FR202 FR203 FR204 FR205 FR206 FR207 FR207 -STR UNIT Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 400 600 800 1000 1000 V Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 700 V Maximum DC Blocking Voltage VDC 50 100 200 400 600 800 1000 1000 V Maximum Average Forward Current 0.375"(9.5mm) Lead Length Ta = 55 °C IF(AV) 2.0 A IFSM 75 A VF 1.3 V IR 10 µA IR(H) 500 µA Peak Forward Surge Current, 8.3ms Single half sine wave Superimposed on rated load (JEDEC Method) Maximum Peak Forward Voltage at IF = 2.0 Amps. Maximum DC Reverse Current Ta = 25 °C at Rated DC Blocking Voltage Ta = 100 °C Maximum Reverse Recovery Time ( Note 1 ) Trr 150 250 500 250 ns Typical Junction Capacitance ( Note 2 ) CJ 15 pf Junction Temperature Range TJ - 65 to + 150 °C Storage Temperature Range TSTG - 65 to + 150 °C Notes : ( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A. ( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 VDC Page 1 of 2 Rev. 01 : April 2, 2002 RATING AND CHARACTERISTIC CURVES ( FR201 - FR207-STR ) FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 Ω Trr 10 Ω + 0.5 A D.U.T. + 0 PULSE GENERATOR ( NOTE 2 ) 50 Vdc (approx) 1Ω - 0.25 A OSCILLOSCOPE ( NOTE 1 ) - 1.0 A SET TIME BASE FOR 50-100 ns/cm NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 1 cm 2. Rise time = 10 ns max., Source Impedance = 50 ohms. 3. All Resistors = Non-inductive Types. FIG.2 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT FIG.3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 75 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES 2.0 1.6 1.2 0.8 0.4 8.3 ms SINGLE HALF SINE WAVE 60 Ta = 55 °C 45 30 15 60Hz RESISTIVE OR INDUCTIVE LOAD 0 0 25 50 75 100 125 150 0 175 1 2 AMBIENT TEMPERATURE, ( °C) FIG.4 - TYPICAL FORWARD CHARACTERISTICS 6 10 20 40 60 100 FIG.5 - TYPICAL REVERSE CHARACTERISTICS 100 10 Pulse Width = 300 µs 2% Duty Cycle REVERSE CURRENT, MICROAMPERES FORWARD CURRENT, AMPERES 4 NUMBER OF CYCLES AT 60Hz TJ = 25 °C 10 1.0 TJ = 100 °C 1.0 0.1 TJ = 25 °C 0.01 0.1 0 20 40 60 80 100 120 140 PERCENT OF RATED REVERSE VOLTAGE, (%) 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 FORWARD VOLTAGE, VOLTS Page 2 of 2 Rev. 01 : April 2, 2002