MAC4M, MAC4N Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. • Blocking Voltage to 800 Volts • On-State Current Rating of 4.0 Amperes RMS at 100°C • Uniform Gate Trigger Currents in Three Modes • High Immunity to dv/dt — 500 V/µs minimum at 125°C • Minimizes Snubber Networks for Protection • High Surge Current Capability – 40 Amperes • Industry Standard TO-220AB Package • High Commutating di/dt — 6.0 A/ms minimum at 125°C • Operational in Three Quadrants: Q1, Q2, and Q3 • Device Marking: Logo, Device Type, e.g., MAC4M, Date Code www.kersemi.com TRIACS 4 AMPERES RMS 600 thru 800 VOLTS MT2 MT1 G MAXIMUM RATINGS (TJ = 25°C unless otherwise noted) Rating Symbol Peak Repetitive Off–State Voltage(1) (TJ = –40 to 125°C, Sine Wave, 50 to 60 Hz, Gate Open) MAC4M MAC4N VDRM, VRRM On-State RMS Current (Full Cycle Sine Wave, 60 Hz, TC = 100°C) IT(RMS) Peak Non-Repetitive Surge Current (One Full Cycle Sine Wave, 60 Hz, TJ = 125°C) Circuit Fusing Consideration (t = 8.33 ms) Peak Gate Power (Pulse Width ≤ 1.0 µs, TC = 100°C) Average Gate Power (t = 8.3 ms, TC = 100°C) Operating Junction Temperature Range Storage Temperature Range Value Unit 4 Volts 600 800 4.0 Amps ITSM 40 Amps I2t 6.6 A2sec PGM 0.5 Watt PG(AV) 0.1 Watt TJ – 40 to +125 °C Tstg – 40 to +150 °C 1 3 TO–220AB CASE 221A STYLE 4 PIN ASSIGNMENT 1 Main Terminal 1 2 Main Terminal 2 3 Gate 4 Main Terminal 2 ORDERING INFORMATION Device 1 2 Package Shipping MAC4M TO220AB 50 Units/Rail MAC4N TO220AB 50 Units/Rail MAC4M, MAC4N THERMAL CHARACTERISTICS Characteristic Thermal Resistance — Junction to Case — Junction to Ambient Symbol Value Unit RθJC RθJA 2.2 62.5 °C/W TL 260 °C Maximum Lead Temperature for Soldering Purposes 1/8″ from Case for 10 Seconds ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise noted; Electricals apply in both directions) Symbol Min Typ Max — — — — 0.01 2.0 — 1.3 1.6 8.0 8.0 8.0 12 16 21 35 35 35 6.0 20 35 — — — 25 40 20 60 80 60 0.5 0.5 0.5 0.8 0.8 0.8 1.3 1.3 1.3 (di/dt)c 6.0 8.4 — A/ms Critical Rate of Rise of Off-State Voltage (VD = 0.67 x Rated VDRM, Exponential Waveform, Gate Open, TJ = 125°C) dv/dt 500 1500 — V/µs Repetitive Critical Rate of Rise of On-State Current IPK = 50 A; PW = 40 µsec; diG/dt = 200 mA/µsec; f = 60 Hz di/dt — — 10 A/µs Characteristic Unit OFF CHARACTERISTICS Peak Repetitive Blocking Current (VD = Rated VDRM, VRRM; Gate Open) TJ = 25°C TJ = 125°C IDRM, IRRM mA ON CHARACTERISTICS Peak On-State Voltage(1) (ITM = ± 6.0 A) VTM Gate Trigger Current (Continuous dc) (VD = 12 V, RL = 100 Ω) MT2(+), G(+) MT2(+), G(–) MT2(–), G(–) IGT Holding Current (VD = 12 V, Gate Open, Initiating Current = ±200 mA) IH Latching Current (VD = 12 V, IG = 35 mA) MT2(+), G(+) MT2(+), G(–) MT2(–), G(–) IL Gate Trigger Voltage (Continuous dc) (VD = 12 V, RL = 100 Ω) MT2(+), G(+) MT2(+), G(–) MT2(–), G(–) V mA mA mA VGT V DYNAMIC CHARACTERISTICS Rate of Change of Commutating Current (VD = 400 V, ITM = 4.0 A, Commutating dv/dt = 18 V/µs, Gate Open, TJ = 125°C, f = 250 Hz, CL = 5.0 µF, LL = 20 mH, No Snubber) (1) Pulse Test: Pulse Width ≤ 2.0 ms, Duty Cycle ≤ 2%. www.kersemi.com 2 MAC4M, MAC4N Voltage Current Characteristic of Triacs (Bidirectional Device) + Current Symbol Parameter VDRM IDRM Peak Repetitive Forward Off State Voltage VRRM IRRM Peak Repetitive Reverse Off State Voltage VTM IH Maximum On State Voltage VTM Quadrant 1 MainTerminal 2 + on state Peak Forward Blocking Current IH IRRM at VRRM Peak Reverse Blocking Current off state IH Holding Current Quadrant 3 VTM MainTerminal 2 – Quadrant Definitions for a Triac MT2 POSITIVE (Positive Half Cycle) + (+) MT2 Quadrant II (+) MT2 Quadrant I (+) IGT GATE (–) IGT GATE MT1 MT1 REF REF IGT – + IGT (–) MT2 Quadrant III (–) MT2 Quadrant IV (+) IGT GATE (–) IGT GATE MT1 MT1 REF REF – MT2 NEGATIVE (Negative Half Cycle) All polarities are referenced to MT1. With in–phase signals (using standard AC lines) quadrants I and III are used. www.kersemi.com 3 + Voltage IDRM at VDRM MAC4M, MAC4N 1.1 VGT, GATE TRIGGER VOLTAGE (VOLTS) IGT, GATE TRIGGER CURRENT (mA) 100 Q2 Q3 Q1 10 1 – 40 – 25 – 10 5 20 35 50 65 80 95 110 125 TJ, JUNCTION TEMPERATURE (°C) 1.0 Q3 0.9 Q2 0.8 Q1 0.7 0.6 0.5 0.4 – 40 – 25 – 10 5 20 35 50 65 80 95 110 125 TJ, JUNCTION TEMPERATURE (°C) Figure 2. Typical Gate Trigger Voltage versus Junction Temperature Figure 1. Typical Gate Trigger Current versus Junction Temperature 100 Q2 IH, HOLDING CURRENT (mA) IL , LATCHING CURRENT (mA) 100 Q1 Q3 10 MT2 Positive MT2 Negative 10 1 – 40 – 25 – 10 5 20 35 50 65 80 95 110 125 TJ, JUNCTION TEMPERATURE (°C) 1 – 40 – 25 – 10 5 20 35 50 65 80 95 110 125 TJ, JUNCTION TEMPERATURE (°C) Figure 4. Typical Holding Current versus Junction Temperature P(AV), AVERAGE POWER DISSIPATION (WATTS) Figure 3. Typical Latching Current versus Junction Temperature TC , CASE TEMPERATURE (°C) 125 120 30° 115 60° 90° 120° 110 180° 105 DC 0 0.5 1 1.5 2 2.5 3 3.5 IT(RMS), RMS ON-STATE CURRENT (AMPS) 4 6 DC 5 180° 120° 4 90° 60° 3 30° 2 1 0 0 Figure 5. Typical RMS Current Derating 1 2 3 0.5 1.5 2.5 3.5 IT(AV), AVERAGE ON-STATE CURRENT (AMPS) Figure 6. On-State Power Dissipation www.kersemi.com 4 4 IT, INSTANTANEOUS ON-STATE CURRENT (AMPS) 100 Maximum @ TJ = 25°C Typical @ TJ = 25°C Maximum @ TJ = 125°C 10 1 r(t), TRANSIENT THERMAL RESISTANCE (NORMALIZED) MAC4M, MAC4N 1 0.1 0.01 0.1 1 10 100 t, TIME (ms) 1000 Figure 8. Typical Thermal Response 0.1 0 1 2 3 4 VT, INSTANTANEOUS ON-STATE VOLTAGE (VOLTS) Figure 7. Typical On-State Characteristics www.kersemi.com 5 10000 MAC4M, MAC4N PACKAGE DIMENSIONS TO–220AB CASE 221A–09 ISSUE Z –T– SEATING PLANE C T S 4 DIM A B C D F G H J K L N Q R S T U V Z A Q 1 2 3 U H K Z L R V NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. J G D N INCHES MIN MAX 0.570 0.620 0.380 0.405 0.160 0.190 0.025 0.035 0.142 0.147 0.095 0.105 0.110 0.155 0.018 0.025 0.500 0.562 0.045 0.060 0.190 0.210 0.100 0.120 0.080 0.110 0.045 0.055 0.235 0.255 0.000 0.050 0.045 ––– ––– 0.080 STYLE 4: PIN 1. 2. 3. 4. www.kersemi.com 6 MILLIMETERS MIN MAX 14.48 15.75 9.66 10.28 4.07 4.82 0.64 0.88 3.61 3.73 2.42 2.66 2.80 3.93 0.46 0.64 12.70 14.27 1.15 1.52 4.83 5.33 2.54 3.04 2.04 2.79 1.15 1.39 5.97 6.47 0.00 1.27 1.15 ––– ––– 2.04 MAIN TERMINAL 1 MAIN TERMINAL 2 GATE MAIN TERMINAL 2