HEDS-9730, HEDS-9731 Small Optical Encoder Modules 480lpi Digital Output Data Sheet Description Features The HEDS-973X is a high performance incremental encoder module. When operated in conjunction with either a codewheel or codestrip, this module detects rotary or linear position. The encoder consists of a lensed LED source and a detector IC enclosed in a small Cshaped plastic package. Due to a highly collimated light source and a unique photodetector array, the module is extremely tolerant to mounting misalignment. • Small Size The two channel digital outputs and 3.3V supply input are accessed through four solder plated leads located on 2.54mm (0.1inch) centers. • Wave Solderable The standard HEDS-973X is designed for use with an appropriate optical radius codewheel or linear codestrip. Other options are available. Please contact the factory for more information. Block Diagram RESISTOR VCC 3 LENS PHOTODIODES COMPARATORS A + LED A B + B - CHANNEL A 2 • High Resolution • Two Channel Quadrature Output • Linear and Rotary Applications • No Signal Adjustment required • TTL or 3.3V/5V CMOS Compatible • Lead-free Package • -40°C to 85°C Operating Temperature • Single 3.3V Supply Applications The HEDS-973X provides sophisticated motion detection, making closed loop control very cost competitive. Typical applications include printers, plotters, copiers and office automation equipment. Note: Avago Technologies’ encoders are not recommended for use in safety critical applications, e.g., ABS braking systems and critical-care medical equipment. Please contact a sales representative if more clarification is needed. CHANNEL B 4 SIGNAL PROCESSING CIRCUITRY GND 1 EMITTER SECTION CODE WHEEL DETECTOR SECTION Figure 1 ESD WARNING: NORMAL HANDLING PRECAUTIONS SHOULD BE TAKEN TO AVOID STATIC DISCHARGE. Theory of Operation Definitions A HEDS-973X is a C-shaped emitter/detector module. Coupled with a codewheel, it translates rotary motion into a two-channel digital output; coupled with a codestrip, it translates linear motion into digital outputs. Note: Refer to Figure 2 As seen in Figure 1, the module contains a single Light Emitting Diode (LED) as its light source. The light is collimated into parallel beam by means of a single lens located directly over the LED. Opposite the emitter is the integrated detector circuit. This IC consists of photodetectors and a signal processing circuitry necessary to produce the digital waveforms. 1 shaft Rotation = 360 degrees The codewheel/codestrip moves between the emitter and detector, causing the light beam to be interrupted by the pattern of spaces and bars on the codewheel/ codestrip. The photodiodes, which detect these interruptions, are arranged in a pattern that corresponds to the radius and count density of the codewheel/ codestrip. These photodiodes are also spaced such that a light period on one pair of detectors corresponds to a dark period on the adjacent pairs of detectors. The photodiode outputs are fed through the signal processing circuitry. Two comparators receive these signal and produce the final outputs for Channels A and B. Due to this integrated phasing technique the output of channel A is in quadrature with Channel B (90 degrees out of phase). Output Waveforms C AMPLITUDE CHANNEL A ф S2 S3 S4 CHANNEL B ROTATION Figure 2. 2 = N cycles 1 cycle (c) = 360 electrical degree, equivalent to 1 bar and window pair. Pulse Width (P): The number of electrical degrees that an output is high during one cycle, nominally 180°e or 1/2 a cycle. Pulse Width Error (ΔP): The deviation in electrical degrees of the pulse width from its ideal value of 180°e. State Width (S): The number of electrical degrees between a transition in the output of channel A and the neighboring transition in the output of channel B. There are 4 states per cycle, each nominally 90°e. State Width Error (ΔS): The deviation in electrical degrees of each state width from its ideal value of 90°e. Phase (φ): The number of electrical degrees between the center of the high state on channel A and the center of the high state on channel B. This value is nominally 90°e for quadrature output. Phase Error (Δφ): The deviation in electrical degrees of the phase from its ideal value of 90°e. P S1 Count (N): The number of bar and window pairs or counts per revolution (CPR) of the codewheel. Or the number of lines per inch of the codestrip (LPI) Direction of Rotation: When the codewheel rotates in the counter-clockwise direction (as viewed from the encoder end of the motor), channel A will lead channel B. If the codewheel rotates in the clockwise direction, channel B will lead channel A. Optical Radius (Rop): The distance from the codewheel’s center of rotation to the optical center (O°C) of the encoder module. Angular Misalignment Error (EA): Angular misalignment of the sensor in relation to then tangential direction. This applies for both rotary and linear motion. Mounting Position (RM): Distance from Motor Shaft center of rotation to center of Alignment Tab receiving hole. Absolute Maximum Ratings Parameter Symbol Min. Max. Units Storage Temperature TS -40 85 °C Operating Temperature TA -40 85 °C Supply Voltage VCC -0.5 7 Volts Output Voltage VO -0.5 VCC Volts Output Current per Channel IOUT -1.5 19 mA Soldering Temperature TSOL 20 260 °C Notes t* 5 sec Recommended Operating Conditions Parameter Symbol Min. Temperature TA -40 Supply Voltage VCC 2.8 Load Capacitance CL Pull-up Resistor RL Frequency f Angular Misalignment EA Mounting Position RM Typ. 3.3 or 5 Max. Units 85 °C 5.2 Volts 100 pF Notes Ripple < 100mVp-p none -2.0 Recommend no pullup. Device has integrated 2.5 kΩ on outputs 0.0 40 kHz Velocity (rpm) x N/60 +2.0 Deg. Refer to Mounting Consideration ROP-0.14 (ROP -0.006) Mm (inch) Refer to Mounting Consideration Electrical Characteristics Electrical Characteristics Over the Recommended Operating Conditions. Typical Values at 25°C. Parameter Symbol Min. Typ. Max. Units Notes Supply Current ICC 12 25 40 mA Typ. 3.3V 55 85 High Level Output Voltage VOH Low Level Output Voltage VOL 2.4 0.4 Typ. 5V Volts When VOH = 2.4V (Min)Typ. IOH = -0.4 mA @ 3.3VTyp. IOH = -1.0 mA @ 5V Volts When VOL = 0.4V (Max)Typ. IOL = 12 mA @ 3.3VTyp. IOL = 14 mA @ 5V CL=25 pF Rise Time tr 200 ns Fall Time tf 50 ns Encoding Characteristics Encoding Characteristics Over the Recommended Operating Conditions and Mounting Conditions These characteristics do not include codewheel/codestrip contribution. The typical values are average over the full rotation of the codewheel Parameter Symbol Typical Maximum Units Pulse Width Error ΔP 5 50 °e State Width Error ΔS Δφ 3 50 °e 2 15 °e Phase Error 3 Notes Mounting Considerations 5.32 MAX. (0.209) 4.40 ± 0.13 0.17 ± 0.005 CL OF ALIGNMENT TAB SEE NOTE 1 Rm 6.30 MAX. (0.248) Rop IMAGE SIDE OF CODEWHEEL/CODESTRIP 6.50 MIN. (0.256) CENTER OF ROTATION MOTOR SHAFT CENTER -A- 2.03 MIN. (0.080) 1.0 DEEP MIN. (0.039) EA 2X R ALIGNMENT TAB RECEIVING HOLE Rm = Rop - 0.14 (0.006) 2.03 HOLE MIN. (0.080) 1.0 DEEP MIN. (0.039) DIMENSIONS IN MILLIMETERS (INCHES). A 0.13 mm (0.005") Note: These dimensions include shaft end play and codewheel warp. For both rotary and linear motion, angular misalignment, EA must be * ± 1 degrees to achieve Encoding Characteristics. All dimension for mounting the module and codewheel/codestrip should be measured with respect to two mounting posts, as shown above Recommended Codewheel and Codestrip Characteristics MAX 3.4 (0.134) Wb Ww Lw Rc Rop L W1 W2 Ww 4 Wb Parameter Symbol Min. Max. Window/bar Ratio Ww/Wb 0.9 1.1 Window Length (Rotary) LW 1.80 (0.071) 2.31 (0.091) mm (inch) Absolute Maximum Codewheel Radius (Rotary) Rc Rop + 3.40 (Rop + 0.134) mm (inch) Center of Post to Inside Edge of Window W1 1.04 (0.041) mm (inch) Center of Post to Outside Edge of Window W2 0.76 (0.036) mm (inch) Center of Post to Inside Edge of Codestrip L 3.60 (0.142) Unit mm (inch) Notes Includes eccentricity errors Ordering Information HEDS - 973 Option Resolution 3 - 480 LPI Lead Configurations 0 - Straight leads 1 - Bent leads Bracket Option 50 Package Dimension Option 50 LEAD THICKNESS = 0.25 mm LEAD PITCH = 2.54 mm 3.8 5.5 ± 0.3 1.4 0.8 1.70 ± 0.15 4.2 3.90 ± 0.10 7.5 10.1 PART # (REFER -05) GND 50 7.0 12.6 ± 0.5 YYWW 3.9 X 4.2 C 5.0 2x ∅ 2.00 ± 0.02 PIN 1 ID AVAGO 6.4 0.14 (OPTICAL CENTER) CH A OPTION CODE XXXXX 8.7 3.0 R 2.6 V CC R 1.4 CH B 10.8 ± 0.5 0.5 8.4 DATE CODE 15.0 C = COUNTRY OF ORIGIN MARKING (REFER -05 FOR DETAILS) 20.2 ± 0.5 1.8 9.8 Bent Version - Option 50 LEAD THICKNESS = 0.25 mm LEAD PITCH = 2.54 mm 6.0 4.2 3.9 0.14 (OPTICAL CENTER) 0.8 2x ∅ 2.00 ± 0.02 1.70 ± 0.15 4.2 PART # (REFER -05) 3.90 ± 0.10 7.5 10.1 GND 50 V CC AVAGO 9.8 0.5 10.8 ± 0.5 PIN 1 ID 7.0 12.6 ± 0.5 8.4 15.0 20.2 ± 0.5 1.8 3.8 5 CH A 9.2 ± 0.3 X 5.0 OPTION CODE YYWW 1.4 6.4 5° TYP. C 8.7 R 1.4 XXXXX R 2.6 CH B 3.0 ± 0.3 DATE CODE C = COUNTRY OF ORIGIN MARKING (REFER -05 FOR DETAILS) Wave Soldering Profile Y-AXIS 7 sec MAX. 260°C FLOW COOL DOWN 120° C/20 sec MAX. X-AXIS Parameter Min. Max. Nominal values Units A Solder Pot Temperature NA 260 250 - 260 °C B Preheat Zone Temperature 85 120 100 - 120 °C C Dip in Time 5 7 5 sec D Solder Pot Zone (PCB Top) NA NA NA °C E Solder Pot Zone (Encoder Lead) 200 NA ≥ 200 °C For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2009 Avago Technologies. All rights reserved. Obsoletes 5989-0837EN AV02-1057EN - January 5, 2010