E-pHEMT MMIC AE510 Product Features Applications • 30 ~ 3000MHz • High Gain • High linearity • SOIC-8 SMD Type package • Lower manufacturing cost • -74dBc CSO 79 Channels @ +30dBmV/ch • -73dBc CTB 79 Channels @ +30dBmV/ch • Low Noise Amplifier for CATV • Cable Modem • FTTH (G-PON, GE-PON) • Optical node Package Type : SOIC-8 Description AE510 is designed as low cost drive amplifiers for many applications including FTTH, CATV System. This MMIC is based on Gallium Arsenide Enhancement Mode pHEMT which shows low current draw and very low noise. The data in this spec sheet is valid only for 75ohm application. 50ohm data is in a separate spec sheet. Electrical Specifications PARAMETER UNIT MIN TYP MAX CONDITION Frequency MHz 30 - 3000 - Gain dB 17 14 19 17 - 30 ~ 1000MHz 50 ~ 2700MHz Gain Flatness dB - 0.7 2.5 - 30 ~ 1000MHz 50 ~ 2700MHz Input Return Loss dB - -17 - - Output Return Loss dB - -18 - - Output IP3 dBm 37 40 - @ 500MHz/5dBm 2tone 1dB Compression Point dBm 20 23 - @500MHz Noise Figure dB - 3.0 4.0 30 ~ 1000MHz dBc - -74 -69 dBc - -73 -68 mA - 200 - CSO 30 ~ 1004MHz CTB DC Current 79 channel, +30dBmV/ch Vdd = 5.0V Note 1. Test conditions unless otherwise noted. Test Freq = 500MHz, T=25℃, Vdd=5V, 75Ω system 2. OIP3 measured with 2 tones at an output power of +5dBm/tone separated by 1MHz, Test Freq = 500MHz Absolute Maximum Ratings PARAMETER UNIT MIN TYP MAX Device Voltage VDC - 5 8 Operating Temperature ℃ -40 - 85 Storage Temperature ℃ -40 - 150 ESD Human Body Model - - Class 1A - Moisture Sensitivity Level - - MSL1 - Junction Temperature (Tj) ℃ - - 180 Thermal Resistance (Rth) ℃/W - 45 - Korean Facilities : 82-31-8069-3036 / [email protected] US Facility : 919-677-8780 / [email protected] All specifications may change without notice 1/6 Version 1.1 AE510 E-pHEMT MMIC Application Circuit @ 30 ~ 1000MHz, 75ohm System, VDD=5V Typical Performance @ VDD=5V, IDS=200mA, T=25℃, 75ohm System PARAMETER UNIT TYPICAL Frequency MHz 30 500 1000 Gain(S21) dB 18.5 19.2 18.6 Gain vs. Frequency Input Return Loss(S11) dB -7.5 -27.2 -19.7 Output Return Loss(S22) dB -8.0 -18.2 -15.5 Output IP3 dBm 35.2 40 35.8 1dB Compression Point dBm 21.5 23 22 Noise Figure dB 2.8 2.9 3.2 CSO* dBc -74 CTB* dBc -73 Current mA 200 21.0 85°C 25°C 20.0 - 40°C 19.0 18.0 17.0 16.0 30 200 400 600 800 1000 Freq(MHz) * 79channels_Flat, +30dBmV S11 vs. Frequency S22 vs. Frequency 10.0 10.0 85°C 85°C 25°C 25°C 0.0 0.0 - 40°C -10.0 -10.0 -20.0 -20.0 -30.0 -30.0 -40.0 - 40°C -40.0 30 200 400 600 800 1000 30 Freq(MHz) 400 600 800 1000 Freq(MHz) Korean Facilities : 82-31-8069-3036 / [email protected] US Facility : 919-677-8780 / [email protected] 200 All specifications may change without notice 2/6 Version 1.1 AE510 E-pHEMT MMIC OIP3 vs. Frequency Noise Figure vs. Frequency 6.0 50.0 85°C 85°C 45.0 25°C 5.0 25°C - 40°C - 40°C 40.0 4.0 35.0 3.0 30.0 2.0 25.0 30 200 400 600 800 1000 1.0 30 Freq(MHz) 200 400 600 800 1000 Freq(MHz) P1dB vs. Frequency 28 85°C 25°C 26 - 40°C 24 22 20 18 30 200 400 600 800 1000 Freq(MHz) Application Circuit @ 50 ~ 2700MHz, 75ohm System, VDD=5V Korean Facilities : 82-31-8069-3036 / [email protected] US Facility : 919-677-8780 / [email protected] All specifications may change without notice 3/6 Version 1.1 AE510 E-pHEMT MMIC Typical Performance @ VDD=5V, IDS=200mA, T=25℃, 75ohm System Typical PARAMETER Units Frequency GHz 0.05 1 S-Parameter S-Parameter 2.7 dB 18.6 17.2 17 16.1 dB -7 -6.7 -13 -12 Output return loss(S22) dB -8.5 -6.3 -9.2 -14 Output IP3 dBm 36.7 35.8 36.5 33.5 1dB Compression Point dBm 21 23 22 18 Noise Figure dB 2.8 3.2 4.9 5.5 CSO* dBc -72 CTB* dBc -69 Current mA 200 10 20 5 S21 15 0 10 -5 S22 5 -10 0 Return Loss(dB) Gain(S21) Input return loss(S11) Gain(dB) 2 25 -15 S11 -5 0.0 0.5 1.0 -20 1.5 2.0 2.5 3.0 Freq(GHz) * 79channels_Flat, +30dBmV Frequency vs. P1dB 6 30 5 25 P1dB(dBm) NF(dB) Frequency vs. Noise Figure 4 3 15 10 2 1 0.05 20 0.4 0.8 1.2 1.6 2 2.4 2.8 5 0.05 0.4 0.8 1.2 1.6 2 2.4 2.8 Freq(GHz) Freq(GHz) Frequency vs. OIP3 45 OIP3(dBm) 40 35 30 25 20 0.05 0.4 0.8 1.2 1.6 2 2.4 2.8 Freq(GHz) Korean Facilities : 82-31-8069-3036 / [email protected] US Facility : 919-677-8780 / [email protected] All specifications may change without notice 4/6 Version 1.1 AE510 E-pHEMT MMIC Package Dimensions (Type: SOIC-8) * Unit: mm[inch] | Tolerance ±0.2[.008] Pin Description Pin No Function Pin No Function 1 RF IN(2) 5 RF OUT(1) 2 GND 6 GND 3 GND 7 GND 4 RF IN(1) 8 RF OUT(2) Recommended Pattern Mounting Configuration Notes 1. Ground / thermal via holes are critical for the proper performance of this device. 2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. Mounting screws can be added near the part to fasten the board to a heat sink. Ensure that the ground / thermal via hole region contacts the heat sink. 4. Do not put solder mask on the backside of the PCB in the region where the board contacts the heat sink. 5. RF trace width depends upon the PCB material and construction. 6. Use 1 oz. Copper minimum. Korean Facilities : 82-31-8069-3036 / [email protected] US Facility : 919-677-8780 / [email protected] All specifications may change without notice 5/6 Version 1.1 AE510 E-pHEMT MMIC Revision History Part Number Release Date Version Modification Data Sheet Status AE510 20140418 1.1 Thermal Resistance (1p) - AE510 20131018 1.0 Typical performance (2p) - AE510 20130820 0.1 Initial Release of Data sheet Preliminary RFHIC Corporation reserves the right to make changes to any products herein or to discontinue any product at any time without notice. While product specifications have been thoroughly examined for reliability, RFHIC Corporation strongly recommends buyers to verify that the information they are using is accurate before ordering. RFHIC Corporation does not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including without limitation consequential or incidental damages. RFHIC products are not intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. Buyer uses or sells such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC Corporation and its directors, officers, stockholders, employees, representatives and distributors harmless against any and all claims arising out of such unauthorized use. Sales, inquiries and support should be directed to the local authorized geographic distributor for RFHIC Corporation. For customers in the US, please contact the US Sales Team at 919677-8780. For all other inquiries, please contact the International Sales Team at 82-31-8069-3036 Korean Facilities : 82-31-8069-3036 / [email protected] US Facility : 919-677-8780 / [email protected] All specifications may change without notice 6/6 Version 1.1