DATASHEET ISL6561 Multi-Phase PWM Controller with Precision rDS(ON) or DCR Differential Current Sensing for VR10.X Application FN9098 Rev 6.00 November 10, 2015 The ISL6561 controls microprocessor core voltage regulation by driving up to 4 synchronous-rectified buck channels in parallel. Multi-phase buck converter architecture uses interleaved timing to multiply channel ripple frequency and reduce input and output ripple currents. Lower ripple results in fewer components, lower component cost, reduced power dissipation, and smaller implementation area. Features Microprocessor loads can generate load transients with extremely fast edge rates. The ISL6561 features a high bandwidth control loop and ripple frequencies of >4MHz to provide optimal response to the transients. • Precision rDS(ON) or DCR Current Sensing - Integrated Programmable Temperature Compensation - Accurate Load-Line Programming - Accurate Channel-Current Balancing - Differential Current Sense - Low-Cost, Lossless Current Sensing Today’s microprocessors require a tightly regulated output voltage position versus load current (droop). The ISL6561 senses current by utilizing patented techniques to measure the voltage across the on resistance, rDS(ON), of the lower MOSFETs or DCR of the output inductor during the lower MOSFET conduction intervals. Current sensing provides the needed signals for precision droop, channel-current balancing, and overcurrent protection. • Precision Multi-Phase Core Voltage Regulation - Differential Remote Voltage Sensing - 0.5% System Accuracy Over Life, Load, Line and Temperature - Adjustable Reference-Voltage Offset • Internal Shunt Regulator for 5V or 12V Biasing • Microprocessor Voltage Identification Input - Dynamic VID™ technology - 6-Bit VID Input - 0.8375V to 1.600V in 12.5mV Steps The accuracy of the current-sensing method is enhanced by the ISL6561’s temperature compensation function. Droop accuracy can be affected by increasing rDS(ON) or DCR with elevated temperature. The ISL6561 uses an internal temperature-sensing element to provide programmable temperature compensation. Correctly applied, temperature compensation can completely nullify the effect of rDS(ON) or DCR temperature sensitivity. • Threshold-Sensitive Enable Function for synchronizing with driver POR A unity gain, differential amplifier is provided for remote voltage sensing. Any potential difference between remote and local grounds can be completely eliminated using the remote-sense amplifier. Eliminating ground differences improves regulation and protection accuracy. The thresholdsensitive enable input is available to accurately coordinate the start up of the ISL6561 with any other voltage rail. Dynamic-VID™ technology allows seamless on-the-fly VID changes. The offset pin allows accurate voltage offset settings that are independent of VID setting. The ISL6561 uses 5V bias and has a built-in shunt regulator to allow 12V bias using only a small external limiting resistor. • Greater Than 1MHz Operation (> 4MHz Ripple) FN9098 Rev 6.00 November 10, 2015 • Overcurrent Protection • Overvoltage Protection - No Additional External Components Needed - OVP Pin to drive opitional Crowbar Device • 2, 3, or 4 Phase Operation • Pb-free Available (RoHS Compliant) • QFN Package Option - QFN Compliant to JEDEC PUB95 MO-220 QFN - Quad Flat No Leads - Product Outline - QFN Near Chip Scale Package Footprint; Improves PCB Efficiency, Thinner in Profile Page 1 of 27 ISL6561 Ordering Information TEMP. (°C) PART NUMBER ISL6561IRZ (Note) PACKAGE (RoHS Compliant) PKG. DWG # -40 to 85 40 Ld 6x6 QFN (Pb-free) L40.6x6 ISL6561IRZ-T (Note) 40 Ld 6x6 QFN Tape and Reel (Pb-free) L40.6x6 NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. Pinout FN9098 Rev 6.00 November 10, 2015 GND PGOOD OVP GND FS GND ENLL EN VCC PWM4 ISL6561 (40-PIN QFN) TOP VIEW 40 39 38 37 36 35 34 33 32 31 28 ISEN2- VID1 4 27 ISEN2+ VID0 5 26 PWM2 VID12.5 6 25 PWM1 GND 7 24 ISEN1+ OFS 8 23 ISEN1- TCOMP 9 22 ISEN3- DAC 10 21 ISEN3+ 11 12 13 14 15 16 17 18 19 20 PWM3 3 GND VID2 RGND ISEN4- VSEN 29 VDIFF 2 COMP VID3 IDROOP ISEN4+ FB 30 GND 1 REF VID4 Page 2 of 27 ISL6561 ISL6561CR Block Diagram OVP VDIFF PGOOD RGND S x1 OVP LATCH VSEN ENLL VCC R 1.24V POWER-ON RESET (POR) EN Q THREE-STATE SOFT START AND FAULT LOGIC OVP CLOCK AND SAWTOOTH GENERATOR +200mV OFS FS PWM1 PWM OFFSET PWM2 PWM REF PWM3 PWM DAC VID4 VID3 PWM4 PWM VID2 DYNAMIC VID VID1 D/A E/A VID0 CHANNEL CURRENT BALANCE VID12.5 CHANNEL DETECT COMP ISEN1+ I_TRIP FB OC IDROOP TCOMP ISEN1- SAMPLE & HOLD CHANNEL ISEN2+ CURRENT ISEN2- SENSE I_TOT ISEN3+ ISEN3- T ISEN4+ ISEN4- GND FN9098 Rev 6.00 November 10, 2015 Page 3 of 27 ISL6561 Typical Application - 4-Phase Buck Converter with Rds,on Sensing and External NTC +12V VIN VCC BOOT UGATE PVCC PHASE HIP6601B DRIVER PWM LGATE FB IDROOP COMP REF VSEN VCC BOOT UGATE ENLL PGOOD ISL6561 OVP VID4 ISEN1+ ISEN1- VID3 PWM1 PVCC PHASE HIP6601B DRIVER PWM LGATE GND PWM2 VID2 VIN VCC RGND VIDPGOOD +12V DAC VDIFF NTC THERMISTOR GND +5V ISEN2+ VID1 ISEN2- VID0 PWM3 VID12.5 ISEN3+ +12V VIN VCC ISEN3OFS PWM4 FS ISEN4+ ISEN4- R T TCOMP GND P LOAD BOOT UGATE PVCC PHASE HIP6601B DRIVER EN PWM LGATE GND +12V +12V VCC VIN BOOT UGATE PVCC PWM PHASE HIP6601B DRIVER LGATE GND FN9098 Rev 6.00 November 10, 2015 Page 4 of 27 ISL6561 Typical Application - 4-Phase Buck Converter with rDS(ON) Sensing and Internal PTC +12V VIN VCC BOOT UGATE PVCC PHASE HIP6601B DRIVER PWM LGATE GND +5V FB COMP REF IDROOP VDIFF VSEN RGND VIDPGOOD +12V DAC VCC BOOT VCC UGATE ENLL ISL6561 PGOOD OVP VID4 ISEN1+ ISEN1- VID3 PWM1 PVCC PHASE HIP6601B PWM DRIVER LGATE GND PWM2 VID2 VIN ISEN2+ VID1 ISEN2- VID0 PWM3 VID12.5 ISEN3+ +12V VIN VCC ISEN3- RT OFS PWM4 FS ISEN4+ ISEN4- TCOMP GND P LOAD BOOT UGATE PVCC EN PHASE HIP6601B DRIVER PWM LGATE +12V GND +12V VCC VIN BOOT UGATE PVCC PWM PHASE HIP6601B DRIVER LGATE GND FN9098 Rev 6.00 November 10, 2015 Page 5 of 27 ISL6561 Typical Application - 4-Phase Buck Converter with DCR Sensing and External NTC +12V VIN VCC BOOT UGATE PVCC PHASE HIP6601B PWM DRIVER GND +5V FB COMP REF IDROOP DAC VDIFF VSEN RGND VCC BOOT UGATE VID4 ISEN1+ ISEN1- VID3 PWM1 VID2 PWM2 VID1 ISEN2+ ISEN2PWM3 PVCC PHASE HIP6601B PWM DRIVER LGATE GND +12V VIN ISEN3+ VID12.5 VCC ISEN3OFS FS RT TCOMP GND VIN VCC ISL6561 VID0 NTC THERMISTOR +12V ENLL VIDPGOOD PGOOD OVP LGATE PWM4 ISEN4+ ISEN4- P LOAD BOOT UGATE PVCC PHASE HIP6601B DRIVER EN PWM LGATE +12V GND +12V VCC VIN BOOT UGATE PVCC PWM PHASE HIP6601B DRIVER LGATE GND FN9098 Rev 6.00 November 10, 2015 Page 6 of 27 ISL6561 Typical Application - 4-Phase Buck Converter with DCR Sensing and Internal PTC +12V VIN VCC BOOT UGATE PVCC PHASE HIP6601B DRIVER PWM LGATE GND +5V FB COMP REF IDROOP VDIFF VSEN RGND VIDPGOOD +12V DAC VCC BOOT VCC UGATE ENLL ISL6561 PGOOD OVP VIN PVCC VID4 ISEN1+ ISEN1- VID3 PWM1 VID2 PWM2 PHASE HIP6601B PWM DRIVER LGATE GND ISEN2+ VID1 ISEN2- VID0 PWM3 VID12.5 ISEN3+ +12V VIN VCC ISEN3OFS FS RT TCOMP GND PWM4 ISEN4+ ISEN4- P LOAD BOOT UGATE PVCC PHASE HIP6601B DRIVER EN PWM LGATE +12V GND +12V VCC VIN BOOT UGATE PVCC PWM PHASE HIP6601B DRIVER LGATE GND FN9098 Rev 6.00 November 10, 2015 Page 7 of 27 ISL6561 Absolute Maximum Ratings Thermal Information Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7V Input, Output, or I/O Voltage (except OVP)GND -0.3V to VCC + 0.3V OVP Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +15V SD (Human body model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >4kV ESD (Machine model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >300V ESD (Charged device model . . . . . . . . . . . . . . . . . . . . . . . . . . >2kV Thermal Resistance JA (°C/W) JC (°C/W) QFN Package (Notes 1, 2) . . . . . . . . 32 3.5 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150°C Maximum Storage Temperature Range . . . . . . . . . . . -65°C to 150°C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300°C (SOIC - Lead Tips Only) Operating Conditions Supply Voltage, VCC (5V bias mode, Note 3) . . . . . . . . . . +5V ±5% Ambient Temperature (ISL6561CR, ISL6561CRZ). . . . . 0°C to 70°C Ambient Temperature (ISL6561IR, ISL6561IRZ) . . . . -40°C to 85°C CAUTION: Stress above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. NOTES: 1. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379 2. For JC, the “case temp” location is the center of the exposed metal pad on the package underside. Electrical Specifications Operating Conditions: VCC = 5V or ICC < 25mA (Note 3). Unless Otherwise Specified PARAMETER TEST CONDITIONS MIN TYP MAX UNITS VCC SUPPLY CURRENT Nominal Supply VCC = 5VDC; EN = 5VDC; RT = 100 k ISEN1 = ISEN2 = ISEN3 = ISEN4 = -70A - 14 18 mA Shutdown Supply VCC = 5VDC; EN = 0VDC; RT = 100 k - 10 14 mA SHUNT REGULATOR VCC Voltage VCC tied to 12VDC thru 300 resistor, , RT = 100k 5.6 5.9 6.3 V VCC Sink Current VCC tied to 12VDC thru 300 resistor, RT = 100k - - 25 mA 4.15 4.31 4.51 V POWER-ON RESET AND ENABLE POR Threshold VCC Rising VCC Falling 3.68 3.82 4.05 V ENABLE Threshold EN Rising 1.22 1.24 1.26 V Hysteresis Fault Reset ENLL Input Logic Low Level ENLL input Logic High Level ENLL Leakage Current 100 mV 1.10 1.14 1.18 V - - 0.4 V 0.8 - ENLL=5V - V 1 A REFERENCE VOLTAGE AND DAC System Accuracy (VID = 1.2V-1.6V) (0°C to (Note 4) 85°C) -0.5 - 0.5 %VID System Accuracy (VID = 1.2V-1.6V) (40°C) (Note 4) -0.8 - 0.8 %VID System Accuracy (VID = 0.8375V1.1875V) (0°C to 85°C) (Note 4) -0.8 - 0.8 %VID System Accuracy (VID = 0.8375V1.1875V) (-40°C) (Note 4) -1.1 - 1.1 %VID A -65 -50 -35 VID Input Low Level VID Pull Up - - 0.4 V VID Input High Level 0.8 - - V -200 - 200 A -50 - 50 A DAC Source/Sink Current REF Source/Sink Current FN9098 Rev 6.00 November 10, 2015 VID = 010100 Page 8 of 27 ISL6561 Electrical Specifications Operating Conditions: VCC = 5V or ICC < 25mA (Note 3). Unless Otherwise Specified (Continued) PARAMETER TEST CONDITIONS MIN TYP MAX UNITS PIN-ADJUSTABLE OFFSET Voltage at OFS pin Offset resistor connected to ground 485 500 515 mV VCC = 5.00V, offset resistor connected to VCC 2.91 3.00 3.09 V -10 - 10 % 0.08 - 1.5 MHz OSCILLATOR Accuracy RT = 100 k Adjustment Range Sawtooth Amplitude - 1.5 - V Max Duty Cycle - 66.7 - % ERROR AMPLIFIER Open-Loop Gain RL = 10k to ground - 80 - dB Open-Loop Bandwidth CL = 100pF, RL = 10k to ground - 18 - MHz Slew Rate CL = 100pF 4.4 6.0 7.5 V/s Maximum Output Voltage 4.0 4.3 - V Output High Voltage @ 2mA 3.7 - - V Output Low Voltage @ 2mA - - 1.40 V REMOTE-SENSE AMPLIFIER Bandwidth - 20 - MHz Output High Current VSEN - RGND = 2.5V -500 - 500 A Output High Current VSEN - RGND = 0.6 -500 - 500 A PWM OUTPUT PWM Output Voltage LOW Threshold Iload = ±500A - - 0.3 V PWM Output Voltage HIGH Threshold Iload = ±500A 4.3 - - V 10 15 20 A - 1 - 1A/V/ °C TEMPERATURE COMPENSATION Temperature Compensation Current @ 40°C and Tcomp = 0.5V Temperature Compensation Transconductance SENSE CURRENT Sensed Current Tolerance (0°C to 85°C) ISEN1 = ISEN2 = ISEN3 = ISEN4 = 80A 74 81 91 A Sensed Current Tolerance (-40°C) ISEN1 = ISEN2 = ISEN3 = ISEN4 = 80A 74 81 92 A Overcurrent Trip Level (0°C to 85°C) 98 110 122 A Overcurrent Trip Level (-40°C) 98 110 127 A - - 0.4 V POWER GOOD AND PROTECTION MONITORS PGOOD Low Voltage IPGOOD = 4mA Under-Voltage Offset From VID (0°C to 85°C) VSEN Falling 72 74 76 %VID Under-Voltage Offset From VID (-40°C) VSEN Falling 71 74 82 %VID Voltage above VID, After Soft Start (Note 5) 180 200 220 mV Overvoltage Threshold Before Enable VCC < POR Threshold Overvoltage Reset Voltage OVP Drive Voltage 1.63 V 1.67 1.80 1.87 V VCC POR Threshold, VSEN Falling - 0.6 - V VCC < POR Threshold - 1.5 - V IOVP = -100mA, VCC = 5V - 1.9 - V 1.4 - - V Minimum VCC for OVP NOTES: 3. When using the internal shunt regulator, VCC is clamped to 6.02V (max). Current must be limited to 25mA or less. 4. These parts are designed and adjusted for accuracy with all errors in the voltage loop included. 5. During soft start, VDAC rises from 0 to VID. The overvoltage trip level is the higher of 1.7V and VDAC + 0.2V. FN9098 Rev 6.00 November 10, 2015 Page 9 of 27 ISL6561 Functional Pin Description VCC - Supplies all the power necessary to operate the chip. The controller starts to operate when the voltage on this pin exceeds the rising POR threshold and shuts down when the voltage on this pin drops below the falling POR threshold. Connect this pin directly to a +5V supply or through a series 300 resistor to a +12V supply. GND - Bias and reference ground for the IC. EN - This pin is a threshold-sensitive enable input for the controller. Connecting the 12V supply to EN through an appropriate resistor divider provides a means to synchronize power-up of the controller and the MOSFET driver ICs. When EN is driven above 1.24V, the ISL6561 is active depending on status of ENLL, the internal POR, and pending fault states. Driving EN below 1.14V will clear all fault states and prime the ISL6556 to soft start when re-enabled. ENLL - This pin is implemented in QFN ISL6561 only. It’s a logic-level enable input for the controller. When asserted to a logic high, the ISL6561 is active depending on status of EN, the internal POR, VID inputs and pending fault states. Deasserting ENLL will clear all fault states and prime the ISL6561 to soft start when re-enabled. FS - A resistor, placed from FS to ground will set the switching frequency. There is an inverse relationship between the value of the resistor and the switching frequency. See Figure 15 and Equation 29. VID4, VID3, VID2, VID1, VID0, and VID12.5 - These are the inputs to the internal DAC that provides the reference voltage for output regulation. Connect these pins either to open-drain outputs with or without external pull-up resistors or to active-pull-up outputs. VID4-VID12.5 have 50uA internal pull-up current sources that diminish to zero as the voltage rises above the logic-high level. These inputs can be pulled up as high as VCC plus 0.3V. VDIFF, VSEN, and RGND - VSEN and RGND form the precision differential remote-sense amplifier. This amplifier converts the differential voltage of the remote output to a single-ended voltage referenced to local ground. VDIFF is the amplifier’s output and the input to the regulation and protection circuitry. Connect VSEN and RGND to the sense pins of the remote load. FB and COMP - Inverting input and output of the error amplifier respectively. FB is connected to VDIFF through a resistor. A negative current, proportional to output current is present on the FB pin. A properly sized resistor between VDIFF and FB sets the load line (droop). The droop scale factor is set by the ratio of the ISEN resistors and the lower MOSFET rDS(ON). COMP is tied back to FB through an external R-C network to compensate the regulator. DAC and REF - The DAC output pin is the output of the precision internal DAC reference. The REF input pin is the positive input of the Error Amp. In typical applications, a FN9098 Rev 6.00 November 10, 2015 1k, 1% resistor is used between DAC and REF to generate a precise offset voltage. This voltage is proportional to the offset current determined by the offset resistor from OFS to ground or VCC. A capacitor is used between REF and ground to smooth the voltage transition during Dynamic VID™ operations. PWM1, PWM2, PWM3, PWM4 - Pulse-width modulation outputs. Connect these pins to the PWM input pins of the Intersil driver IC. The number of active channels is determined by the state of PWM3 and PWM4. Tie PWM3 to VCC to configure for 2-phase operation. Tie PWM4 to VCC to configure for 3-phase operation. ISEN1+, ISEN1-; ISEN2+, ISEN2-; ISEN3+, ISEN3-; ISEN4+, ISEN4- - The ISEN+ and ISEN- pins are current sense inputs to individual differential amplifiers.he sensed current is used as a reference for channel balancing, protection, and regulation. Inactive channels should have their respective current sense inputs left open (for example, for 3-phase operation open ISEN4+). For DCR sensing, connect each ISEN- pin to the node between the RC sense elements. Tie the ISEN+ pin to the other end of the sense capacitor through a resistor, RISEN. The voltage across the sense capacitor is proportional to the inductor current. The sense current is proportional to the output current, and scaled by the DCR of the inductor, divided by RISEN. When configured for rDS(ON) current sensing, the ISEN1-, ISEN2-, ISEN3-, and ISEN4- pins are grounded at the lower MOSFET sources. The ISEN1+, ISEN2+, ISEN3+, and ISEN4+ pins are then held at a virtual ground, such that a resistor connected between them, and the drain terminal of the associated lower MOSET, will carry a current proportional to the current flowing through that channel. The current is determined by the negative voltage developed across the lower MOSFET’s rDS(ON), which is the channel current scaled by rDS(ON). PGOOD - PGOOD is used as an indication of the end of soft-start per Intel VR10. It is an open-drain logic output that is low impedance until the soft start is completed. It will be pulled low again once the under-voltage point is reached. OFS - The OFS pin provides a means to program a dc offset current for generating a dc offset voltage at the REF input. The offset current is generated via an external resistor and precision internal voltage references. The polarity of the offset is selected by connecting the resistor to GND or VCC. For no offset, the OFS pin should be left unterminated. TCOMP - Temperature compensation scaling input. A resistor from this pin to ground scales temperature compensation of internal thermal sense circuitry. The sensed temperature is utilized to modify the droop current output to FB to adjust for MOSFET rDS(ON) or inductor DCR variations with temperature. Page 10 of 27 ISL6561 OVP - Overvoltage protection pin. This pin pulls to VCC and is latched when an overvoltage condition is detected. Connect this pin to the gate of an SCR or MOSFET tied from VIN or VOUT to ground to prevent damage to the load. This pin may be pulled above VCC as high as 15V to ground with an external resistor. However, it is only capable of pulling low when VCC is above 2V. ripple frequency of any one phase. In addition, the peak-topeak amplitude of the combined inductor currents is reduced in proportion to the number of phases (Equations 1 and 2). Increased ripple frequency and lower ripple amplitude mean that the designer can use less per-channel inductance and lower total output capacitance for any performance specification. IDROOP - IDROOP is the ouput pin of sensed average channel current which is propotional to load current. In the application which does not require loadline, leave this pin open. In the application which requires load line, connect this pin to FB so that the sensed average current will flow through the resistor between FB and VDIFF to create a voltage drop which is propotional to load current. Figure 1 illustrates the multiplicative effect on output ripple frequency. The three channel currents (IL1, IL2, and IL3) combine to form the AC ripple current and the DC load current. The ripple component has three times the ripple frequency of each individual channel current. Each PWM pulse is terminated 1/3 of a cycle after the PWM pulse of the previous phase. The peak-to-peak current for each phase is about 7A, and the dc components of the inductor currents combine to feed the load. Operation Multi-Phase Power Conversion Microprocessor load current profiles have changed to the point that the advantages of multi-phase power conversion are impossible to ignore. The technical challenges associated with producing a single-phase converter which is both cost-effective and thermally viable have forced a change to the cost-saving approach of multi-phase. The ISL6561 controller helps simplifying the implementation by integrating vital functions and requiring minimal output components. The block diagrams on pages 2 and 3 provide top level views of multi-phase power conversion using the ISL65556ACB and ISL6561CR controllers. To understand the reduction of ripple current amplitude in the multi-phase circuit, examine the equation representing an individual channel’s peak-to-peak inductor current. V IN – V OUT V OUT I PP = ----------------------------------------------------L fS V (EQ. 1) IN In Equation 1, VIN and VOUT are the input and output voltages respectively, L is the single-channel inductor value, and fS is the switching frequency. INPUT-CAPACITOR CURRENT, 10A/DIV CHANNEL 3 INPUT CURRENT 10A/DIV IL1 + IL2 + IL3, 7A/DIV CHANNEL 2 INPUT CURRENT 10A/DIV IL3, 7A/DIV PWM3, 5V/DIV IL2, 7A/DIV PWM2, 5V/DIV 1s/DIV FIGURE 2. CHANNEL INPUT CURRENTS AND INPUTCAPACITOR RMS CURRENT FOR 3-PHASE CONVERTER IL1, 7A/DIV PWM1, 5V/DIV 1s/DIV FIGURE 1. PWM AND INDUCTOR-CURRENT WAVEFORMS FOR 3-PHASE CONVERTER Interleaving The switching of each channel in a multi-phase converter is timed to be symmetrically out of phase with each of the other channels. In a 3-phase converter, each channel switches 1/3 cycle after the previous channel and 1/3 cycle before the following channel. As a result, the three-phase converter has a combined ripple frequency three times greater than the FN9098 Rev 6.00 November 10, 2015 CHANNEL 1 INPUT CURRENT 10A/DIV The output capacitors conduct the ripple component of the inductor current. In the case of multi-phase converters, the capacitor current is the sum of the ripple currents from each of the individual channels. Compare Equation 1 to the expression for the peak-to-peak current after the summation of N symmetrically phase-shifted inductor currents in Equation 2. Peak-to-peak ripple current decreases by an amount proportional to the number of channels. Outputvoltage ripple is a function of capacitance, capacitor equivalent series resistance (ESR), and inductor ripple Page 11 of 27 ISL6561 current. Reducing the inductor ripple current allows the designer to use fewer or less costly output capacitors. V IN – N V OUT V OUT I L, PP = ----------------------------------------------------------L fS V (EQ. 2) IN Another benefit of interleaving is to reduce input ripple current. Input capacitance is determined in part by the maximum input ripple current. Multi-phase topologies can improve overall system cost and size by lowering input ripple current and allowing the designer to reduce the cost of input capacitance. The example in Figure 2 illustrates input currents from a three-phase converter combining to reduce the total input ripple current. The converter depicted in Figure 2 delivers 36A to a 1.5V load from a 12V input. The RMS input capacitor current is 5.9A. Compare this to a single-phase converter also stepping down 12V to 1.5V at 36A. The single-phase converter has 11.9A RMS input capacitor current. The single-phase converter must use an input capacitor bank with twice the RMS current capacity as the equivalent threephase converter. Figures 16, 17 and 18 in the section entitled Input Capacitor Selection can be used to determine the input-capacitor RMS current based on load current, duty cycle, and the number of channels. They are provided as aids in determining the optimal input capacitor solution. Figure 19 shows the single phase input-capacitor RMS current for comparison. PWM Operation The timing of each converter leg is set by the number of active channels. The default channel setting for the ISL6561 is four. One switching cycle is defined as the time between PWM1 pulse termination signals. The pulse termination signal is the internally generated clock signal that triggers the falling edge of PWM1. The cycle time of the pulse termination signal is the inverse of the switching frequency set by the resistor between the FS pin and ground. Each cycle begins when the clock signal commands the channel-1 PWM output to go low. The PWM1 transition signals the channel-1 MOSFET driver to turn off the channel-1 upper MOSFET and turn on the channel-1 synchronous MOSFET. In the default channel configuration, the PWM2 pulse terminates 1/4 of a cycle after PWM1. The PWM3 output follows another 1/4 of a cycle after PWM2. PWM4 terminates another 1/4 of a cycle after PWM3. If PWM3 is connected to VCC, two channel operation is selected and the PWM2 pulse terminates 1/2 of a cycle later. Connecting PWM4 to VCC selects three channel operation and the pulse-termination times are spaced in 1/3 cycle increments. Once a PWM signal transitions low, it is held low for a minimum of 1/3 cycle. This forced off time is required to ensure an accurate current sample. Current sensing is described in the next section. After the forced off time FN9098 Rev 6.00 November 10, 2015 expires, the PWM output is enabled. The PWM output state is driven by the position of the error amplifier output signal, VCOMP, minus the current correction signal relative to the sawtooth ramp as illustrated in Figure 4. When the modified VCOMP voltage crosses the sawtooth ramp, the PWM output transitions high. The MOSFET driver detects the change in state of the PWM signal, turns off the synchronous MOSFET and turns on the upper MOSFET. The PWM signal remains high until the pulse termination signal commands the beginning of the next cycle by triggering the PWM signal low. Current Sensing The ISL6561 supports inductor DCR sensing or MOSFET rDS(ON) sensing. The internal circuitry, shown in Figures 3 and 5, represents channel n of an N-channel converter. This circuitry is repeated for each channel in the converter, but may not be active depending on the status of the PWM3 and PWM4 pins, as described in the PWM Operation section. MOSFET rDS(ON) Sensing The controller can sense the channel load current by sampling the voltage across the lower MOSFET rDS(ON) as in Figure 6. The amplifier is ground-reference by connecting I r DS ON SEN = I L ------------------------R ISEN VIN In IL SAMPLE & HOLD ISEN+(n) - RISEN (PTC) - ISEN-(n) + I L r DS ON + N-CHANNEL MOSFETs ISL6561 INTERNAL CIRCUIT EXTERNAL CIRCUIT FIGURE 3. MOSFET rDS(ON) CURRENT-SENSING CIRCUIT the ISEN- input to the source of the lower MOSFET. ISEN+ connects to the PHASE node through a resistor RISEN. The voltage across RISEN is equivalent to the voltage drop across the rDS(ON) of the lower MOSFET while it is conducting. The resulting current into the ISEN+ pin is proportional to the channel current IL. The ISEN current is then sampled and held after sufficient settling time as described in current sampling section. The sampled current In, is used for channel-current balance, load-line regulation, and overcurrent protection. From Figure 4, the following equation for ISEN is derived r DS ON I SEN = I L ---------------------R ISEN (EQ. 3) where IL is the channel current. Page 12 of 27 ISL6561 INDUCTOR DCR Sensing Current Sampling An inductor has a distributed direct current winding resistance (DCR). Consider the inductor DCR as a separate lumped quantity as shown in Figure 4. The channel current, IL, flowing through the inductor, also passes through the DCR. Equation 4 shows the s-domain equivalent voltage, VL, across the inductor. During the forced off-time following a PWM transition low, the associated channel current sense amplifier reproduces a signal , ISEN, proportional to the inductor current, IL. Regardless of the current sense method, ISEN is simply a scaled version of the inductor current. Coincident with the falling edge of the PWM signal, the sample and hold circuitry samples ISEN. This is illustrated in Figure 5. The sample time, tSAMP, is fixed and equal to 1/3 of the switching period, tSW. Therefore, the sample current, In, is proportional to the V L = I L s L + DCR (EQ. 4) A simple R-C network across the inductor extracts the DCR voltage, as shown in Figure 5. The voltage on the capacitor, VC, can be shown to be proportional to the channel current IL(see Equation 5). L s ------------+ 1 DCR I L DCR V C = -------------------------------------------------------------------- s RC + 1 (EQ. 5) t SW 1 t SAMP = ---------- = -----------------3 3 f SW (EQ. 7) output current and held for one switching cycle. The sample current is used for current balance, load-line regulation, and overcurrent protection. If the R-C network components are selected such that the RC time constant matches the inductor L/DCR time constant, then VC is equal to the voltage drop across the DCR. VIN IL s L ISL6561 PWM DCR VOUT + - VC(s) R ISEN COUT - + INDUCTOR VL IL tSAMP C PWM(n) SAMPLE CURRENT, In ISL6561 INTERNAL CIRCUIT SWITCHING PERIOD RISEN TIME In FIGURE 5. SAMPLE AND HOLD TIMING SAMPLE & HOLD ISEN- Channel-Current Balance + ISEN+ DCR I SEN = I ------------------LR ISEN FIGURE 4. DCR SENSING CONFIGURATION The capacitor voltage, VC, is replicated across the sense resistor RISEN. so that the current flowing through the sense resistor is proportional to the inductor current. Equation 6 shows that the relationship between the channel current and the sensed current ISEN, is driven by the value of the sense resistor and the inductor DCR. DCR I SEN = I L -----------------R ISEN FN9098 Rev 6.00 November 10, 2015 (EQ. 6) The sampled currents In, from each active channel are summed together and divided by the number of active channels. The resulting cycle average current, IAVG, provides a measure of the total load current demand on the converter during each switching cycle. Channel current balance is achieved by comparing the sampled current of each channel to the cycle average current, and making an appropriate adjustment to each channel pulse width based on the error. Intersil’s patented current-balance method is illustrated in Figure 6, with error correction for channel 1 represented. In the figure, the cycle average current combines with the channel 1 sample, I1, to create an error signal IER. The filtered error signal modifies the pulse width commanded by VCOMP to correct any unbalance and force IER toward zero. The same method for error signal correction is applied to each active channel. Page 13 of 27 ISL6561 + VCOMP + FILTER PWM1 SAWTOOTH SIGNAL f(j) I4 * IER IAVG - N + I3 * I2 I1 NOTE: *Channels 3 and 4 are optional. FIGURE 6. CHANNEL-1 PWM FUNCTION AND CURRENTBALANCE ADJUSTMENT Channel current balance is essential in realizing the thermal advantage of multi-phase operation. The heat generated in down converting is dissipated over multiple devices and a greater area. The designer avoids the complexity of driving multiple parallel MOSFETs, and the expense of using heat sinks and nonstandard magnetic materials. Voltage Regulation The integrating compensation network shown in Figure 7 assures that the steady-state error in the output voltage is limited only to the error in the reference voltage (output of the DAC) and offset errors in the OFS current source, remote-sense and error amplifiers. Intersil specifies the guaranteed tolerance of the ISL6561 to include the combined tolerances of each of these elements. The output of the error amplifier, VCOMP, is compared to the sawtooth waveform to generate the PWM signals. The PWM signals control the timing of the Intersil MOSFET drivers and regulate the converter output to the specified reference voltage. The internal and external circuitry that controls voltage regulation is illustrated in Figure 7. EXTERNAL CIRCUIT RC CC COMP ISL6561 INTERNAL CIRCUIT DAC RREF REF CREF + - FB RFB IDROOP + VDROOP VDIFF VOUT+ VOUT- IAVG VCOMP ERROR AMPLIFIER VSEN + RGND DIFFERENTIAL REMOTE-SENSE AMPLIFIER FIGURE 7. OUTPUT VOLTAGE AND LOAD-LINE REGULATION WITH OFFSET ADUJUSTMENT FN9098 Rev 6.00 November 10, 2015 The ISL6561 incorporates an internal differential remotesense amplifier in the feedback path. The amplifier removes the voltage error encountered when measuring the output voltage relative to the local controller ground reference point resulting in a more accurate means of sensing output voltage. Connect the microprocessor sense pins to the noninverting input, VSEN, and inverting input, RGND, of the remote-sense amplifier. The remote-sense output, VDIFF, is connected to the inverting input of the error amplifier through an external resistor. A digital to analog converter (DAC) generates a reference voltage based on the state of logic signals at pins VID4 through VID12.5. The DAC decodes the a 6-bit logic signal (VID) into one of the discrete voltages shown in Table 1. Each VID input offers a 50A pull-up to an internal 2.5V source for use with open-drain outputs. The pull-up current diminishes to zero above the logic threshold to protect voltage-sensitive output devices. External pull-up resistors can augment the pull-up current sources in case leakage into the driving device is greater than 50A. Load-Line Regulation Some microprocessor manufacturers require a preciselycontrolled output resistance. This dependence of output voltage on load current is often termed “droop” or “load line” regulation. By adding a well controlled output impedance, the output voltage can effectively be level shifted in a direction which works to achieve the load-line regulation required by these manufacturers. TABLE 1. VOLTAGE IDENTIFICATION (VID) CODES VID4 VID3 VID2 VID1 VID0 VID12.5 VDAC 0 1 0 1 0 0 0.8375V 0 1 0 0 1 1 0.8500V 0 1 0 0 1 0 0.8625V 0 1 0 0 0 1 0.8750V 0 1 0 0 0 0 0.8875V 0 0 1 1 1 1 0.9000V 0 0 1 1 1 0 0.9125V 0 0 1 1 0 1 0.9250V 0 0 1 1 0 0 0.9375V 0 0 1 0 1 1 0.9500V 0 0 1 0 1 0 0.9625V 0 0 1 0 0 1 0.975V0 0 0 1 0 0 0 0.9875V 0 0 0 1 1 1 1.0000V 0 0 0 1 1 0 1.0125V 0 0 0 1 0 1 1.0250v 0 0 0 1 0 0 1.0375V 0 0 0 0 1 1 1.0500V Page 14 of 27 ISL6561 TABLE 1. VOLTAGE IDENTIFICATION (VID) CODES (Continued) TABLE 1. VOLTAGE IDENTIFICATION (VID) CODES (Continued) VID4 VID3 VID2 VID1 VID0 VID12.5 VDAC VID4 VID3 VID2 VID1 VID0 VID12.5 VDAC 0 0 0 0 1 0 1.0625V 0 1 1 0 1 0 1.5375V 0 0 0 0 0 1 1.0750V 0 1 1 0 0 1 1.5500V 0 0 0 0 0 0 1.0875V 0 1 1 0 0 0 1.5625V 1 1 1 1 1 1 OFF 0 1 0 1 1 1 1.5750V 1 1 1 1 1 0 OFF 0 1 0 1 1 0 1.5875V 1 1 1 1 0 1 1.1000V 0 1 0 1 0 1 1.600V 1 1 1 1 0 0 1.1125V 1 1 1 0 1 1 1.1250V 1 1 1 0 1 0 1.1375V 1 1 1 0 0 1 1.1500V 1 1 1 0 0 0 1.1625V 1 1 0 1 1 1 1.1750V 1 1 0 1 1 0 1.1875V 1 1 0 1 0 1 1.2000V 1 1 0 1 0 0 1.2125V 1 1 0 0 1 1 1.2250V 1 1 0 0 1 0 1.2475V 1 1 0 0 0 1 1.2500V 1 1 0 0 0 0 1.2625V 1 0 1 1 1 1 1.2750V 1 0 1 1 1 0 1.2875V 1 0 1 1 0 1 1.3000V 1 0 1 1 0 0 1.3125V 1 0 1 0 1 1 1.3250V 1 0 1 0 1 0 1.3375V 1 0 1 0 0 1 1.3500V 1 0 1 0 0 0 1.3625V 1 0 0 1 1 1 1.3750V 1 0 0 1 1 0 1.3875V 1 0 0 1 0 1 1.4000V 1 0 0 1 0 0 1.4125V 1 0 0 0 1 1 1.4250V 1 0 0 0 1 0 1.4375V 1 0 0 0 0 1 1.4500V 1 0 0 0 0 0 1.4625V Where VREF is the reference voltage, VOFS is the programmed offset voltage, VOUT is the total output current of the converter, RISEN is the sense resistor in the ISEN line, and RFB is the feedback resistor. RX has a value of DCR, rDS(ON), or RSENSE depending on the sensing method. 0 1 1 1 1 1 1.4750V Output-Voltage Offset Programming 0 1 1 1 1 0 1.4875V 0 1 1 1 0 1 1.5000V 0 1 1 1 0 0 1.5125V 0 1 1 0 1 1 1.5250V FN9098 Rev 6.00 November 10, 2015 In other cases, the designer may determine that a more cost-effective solution can be achieved by adding droop. Droop can help to control the output-voltage spike that results from fast load-current demand changes. The magnitude of the spike is dictated by the ESR and ESL of the output capacitors selected. By positioning the no-load voltage level near the upper specification limit, a larger negative spike can be sustained without crossing the lower limit. By adding a well controlled output impedance, the output voltage under load can effectively be level shifted down so that a larger positive spike can be sustained without crossing the upper specification limit. As shown in Figure 8, a current proportional to the average current in all active channels, IAVG , flows from FB through a load-line regulation resistor, RFB. The resulting voltage drop across RFB is proportional to the output current, effectively creating an output voltage droop with a steady-state value defined as V DROOP = I AVG R FB (EQ. 8) The regulated output voltage is reduced by the droop voltage VDROOP. The output voltage as a function of load current is derived by combining Equations 8 with the appropriate sample current expression defined by the current sense method employed. I OUT R X V OUT = V REF – V OFFSET – ------------------------------ R FB 4 R ISEN (EQ. 9) The ISL6561 allows the designer to accurately adjust the offset voltage. When a resistor, ROFS, is connected between OFS and VCC, the voltage across it is regulated to 2.0V. This causes a proportional current (IOFS) to flow into OFS. If ROFS is connected to ground, the voltage across it is regulated to 0.5V, and IOFS flows out of OFS. A resistor Page 15 of 27 ISL6561 between DAC and REF, RREF, is selected so that the product (IOFS x RREF) is equal to the desired offset voltage. These functions are shown in Figures 8. FB DYNAMIC VID D/A DAC RREF E/A REF VCC or GND 2.0V - ROFS + + 0.5V VCC - ISL6561CR OFS GND FIGURE 8. OUTPUT VOLTAGE OFFSET PROGRAMMING WITH ISL6561CR As evident in Figure 8, the OFSOUT pin must be connected to the REF pin for this current injection to function in ISL6561CR. The current flowing through RREF creates an offset at the REF pin, which is ultimately duplicated at the output of the regulator. Once the desired output offset voltage has been determined, use the following formulas to set ROFS: For Positive Offset (connect ROFS to VCC): 2 R REF R OFS = -------------------------V OFFSET (EQ. 10) For Negative Offset (connect ROFS to GND): 0.5 R REF R OFS = -----------------------------V OFFSET (EQ. 11) Dynamic VID Modern microprocessors need to make changes to their core voltage as part of normal operation. They direct the core-voltage regulator to do this by making changes to the VID inputs during regulator operation. The power management solution is required to monitor the DAC inputs and respond to on-the-fly VID changes in a controlled FN9098 Rev 6.00 November 10, 2015 manner. Supervising the safe output voltage transition within the DAC range of the processor without discontinuity or disruption is a necessary function of the core-voltage regulator. The ISL6561 checks the VID inputs six times every switching cycle. If the VID code is found to have has changed, the controller waits half of a complete cycle before executing a 12.5mV change. If during the half-cycle wait period, the difference between DAC level and the new VID code changes, no change is made. If the VID code is more than 1 bit higher or lower than the DAC (not recommended), the controller will execute 12.5mV changes six times per cycle until VID and DAC are equal. It is for this reason that it is important to carefully control the rate of VID stepping in 1bit increments. In order to ensure the smooth transition of output voltage during VID change, a VID step change smoothing network composed of RREF and CREF is required for an ISL6561 based voltage regulator. The selection of RREF is based on the desired offset as detailed above in Output-Voltage Offset Programming. The selection of CREF is based on the time duration for 1 bit VID change and the allowable delay time. Assuming the microprocessor controls the VID change at 1 bit every TVID, the relationship between the time constant of RREF and CREF network and TVID is given by Equation 12. C REF R REF = 4 T VID (EQ. 12) Typically RREF is selected to be 1k, so with a VID step change rate of 5s per bit, the value of CREF is 22nF based on Equation 12. Temperature Compensation Both the MOSFET rDS(ON) and inductor DCR of inductor vary in proportion to varying temperature. This means that a circuit using rDS(ON) or DCR to sense channel current is subject to a corresponding error in current measurement. In order to compensate for this temperature-related error, a temperature compensation circuit is provided within ISL6561. This circuit senses the internal IC temperature and, based on a resistor-selectable scaling factor, adjust the droop current ouput to the IDROOP pin. When the TCOMP resistor is properly selected, the droop current can accurately represent the load current to achieve a linear, temperature-independant load line. The value of the Tcomp resistor can be determined using Equation 13. R TCOMP = ---------------------K T K TC (EQ. 13) In Equation 13, KT is the temperature coupling coefficient between the ISL6561 and the lower MOSFET or output inductor. It represents how closely the controller temperature Page 16 of 27 ISL6561 tracks the lower MOSFET or inductor temperature. The value of KT is typically between 75% and100%. KTC is the temperature dependant transconductance of internal compensation circuit. Its vaule is designed as 1A/V/°C. The temperature coefficient of MOSFET rDS(ON) or Inductor DCR is given by . This is the ratio of the change in resistance and the change in temperature. Resistance is normalized to the value at 25°C and the value of is typically between 0.35%/°C and 0.50%/°C. For copper wound inductors, is 0.39%/°C. According to Equation 13, a voltage regulator with 80% thermal coupling coefficient between the controller and lower MOSFET and 0.4%/°C temperature coefficient of MOSFET rDS(ON) requires a 5k TCOMP resistor. Initialization Prior to converter initialization, proper conditions must exist on the enable inputs and VCC. When the conditions are met, the controller begins soft-start. Once the output voltage is within the proper window of operation, PGOOD asserts logic 1. Enable and Disable While in shutdown mode, the PWM outputs are held in a high-impedance state to assure the drivers remain off. The following input conditions must be met before the ISL6561 is released from shutdown mode. ISL6561 INTERNAL CIRCUIT EXTERNAL CIRCUIT +12V VCC POR CIRCUIT 10.7k ENABLE COMPARATOR EN + - 1.40k 1.24V ENLL SOFT START AND FAULT LOGIC FIGURE 9. POWER SEQUENCING USING THRESHOLDSENSITIVE ENABLE (EN) FUNCTION 1 - The bias voltage applied at VCC must reach the internal power-on reset (POR) rising threshold. Once this threshold is reached, proper operation of all aspects of the ISL6561 is guaranteed. Hysteresis between the rising and falling thresholds assure that once enabled, the ISL6561 will not inadvertently turn off unless the bias voltage drops substantially (see Electrical Specifications). 2 - The ISL6561 features an enable input (EN) for power sequencing between the controller bias voltage and another voltage rail. The enable comparator holds the ISL6561 in shutdown until the voltage at EN rises above 1.24V. The enable comparator has about 100mV of hysteresis to prevent bounce. It is important that the driver ICs reach their POR level before the ISL6561 becomes enabled. The schematic in Figure 9 demonstrates sequencing the ISL6561 with the HIP660X family of Intersil MOSFET drivers, which require 12V bias. 3 - The voltage on ENLL must be logic high to enable the controller. This pin is typically connected to the VID_PGOOD. 4 - The VID code must not be 111111 or 111110. These codes signal the controller that no load is present. The controller will enter shut-down mode after receiving either of these codes and will execute soft start upon receiving any other code. These codes can be used to enable or disable the controller but it is not recommended. After receiving one of these codes, the controller executes a 2-cycle delay before changing the overvoltage trip level to the shut-down level and disabling PWM. Overvoltage shutdown cannot be reset using one of these codes. To enable the controller, VCC must be greater than the POR threshold; the voltage on EN must be greater than 1.24V; for ISL6561CR, ENLL must be logic high; and VID cannot be equal to 111111 or 111110. When each of these conditions is true, the controller immediately begins the soft-start sequence. Soft-Start During soft start, the DAC voltage ramps linearly from zero to the programmed VID level as shown in Figure 10. The PWM signals remain in the high-impedance state until the controller detects that the ramping DAC level has reached the output-voltage level. This protects the system against the large, negative inductor currents that would otherwise occur when starting with a pre-existing charge on the output as the controller attempted to regulate to zero volts at the beginning of the soft-start cycle. The soft-start time, tSS, begins with a delay period equal to 64 switching cycles followed by a linear ramp with a rate determined by the switching period, 1/fSW. 64 + 1280 VID t SS = ----------------------------------------f SW FN9098 Rev 6.00 November 10, 2015 (EQ. 14) Page 17 of 27 ISL6561 For example, a regulator with 250kHz switching frequency having VID set to 1.35V has tSS equal to 6.912ms. PGOOD A 100mV offset exists on the remote-sense amplifier at the beginning of soft start and ramps to zero during the first 640 cycles of soft start (704 cycles following enable). This prevents the large inrush current that would otherwise occur should the output voltage start out with a slight negative bias. During the first 640 cycles of soft start (704 cycles following enable) the DAC voltage increments the reference in 25mV steps. The remainder of soft start sees the DAC ramping with 12.5mV steps. OC - + UV SOFT START, FAULT AND CONTROL LOGIC + VDIFF VOUT, 500mV/DIV 100A + I1 REPEAT FOR EACH CHANNEL 75% DAC REFERENCE - OV OC - + 100A IAVG OVP VID + 0.2V FIGURE 11. POWER GOOD AND PROTECTION CIRCUITRY EN, 5V/DIV 500s/DIV FIGURE 10. SOFT-START WAVEFORMS WITH AN UN-BIASED OUTPUT. FSW = 500kHz Fault Monitoring and Protection The ISL6561 actively monitors output voltage and current to detect fault conditions. Fault monitors trigger protective measures to prevent damage to a microprocessor load. One common power good indicator is provided for linking to external system monitors. The schematic in Figure 11 outlines the interaction between the fault monitors and the power good signal. Power Good Signal The power good pin (PGOOD) is an open-drain logic output that transitions high when the converter is operating after soft start. PGOOD pulls low during shutdown and releases high after a successful soft start. PGOOD only transitions low when an under-voltage condition is detected or the controller is disabled by a reset from EN, ENLL, POR, or one of the no-CPU VID codes. After an under voltage event, PGOOD will return high unless the controller has been disabled. PGOOD does not automatically transition low upon detection of an overvoltage condition. FN9098 Rev 6.00 November 10, 2015 Under-Voltage Detection The under-voltage threshold is set at 75% of the VID code. When the output voltage at VSEN is below the under-voltage threshold, PGOOD gets pulled low. Overvoltage Protection When VCC is above 1.4V, but otherwise not valid as defined under Power on Reset in Electrical Specifications, the overvoltage trip circuit is active using auxiliary circuitry. In this state, an overvoltage trip occurs if the voltage at VSEN exceeds 1.8V. With valid VCC, the overvoltage circuit is sensitive to the voltage at VDIFF. In this state, the trip level is 1.7V prior to valid enable conditions being met as described in Enable and Disable. The only exception to this is when the IC has been disabled by an overvoltage trip. In that case the overvoltage trip point is VID plus 200mV. During soft start, the overvoltage trip level is the higher of 1.7V or VID plus 200mV. Upon successful soft start, the overvoltage trip level is 200mV above VID. Two actions are taken by the ISL6561 to protect the microprocessor load when an overvoltage condition occurs. At the inception of an overvoltage event, all PWM outputs are commanded low until the voltage at VSEN falls below 0.6V with valid VCC or 1.5V otherwise. This causes the Intersil drivers to turn on the lower MOSFETs and pull the output voltage below a level that might cause damage to the load. The PWM outputs remain low until VDIFF falls to the programmed DAC level when they enter a high-impedance state. The Intersil drivers respond to the high-impedance input by turning off both upper and lower MOSFETs. If the overvoltage condition reoccurs, the ISL6561 will again Page 18 of 27 ISL6561 command the lower MOSFETs to turn on. The ISL6561 will continue to protect the load in this fashion as long as the overvoltage condition recurs. Simultaneous to the protective action of the PWM outputs, the OVP pin pulls to VCC delivering up to 100mA to the gate of a crowbar MOSFET or SCR placed either on the input rail or the output rail. Turning on the MOSFET or SCR collapses the power rail and causes a fuse placed further up stream to blow. The fuse must be sized such that the MOSFET or SCR will not overheat before the fuse blows. The OVP pin is tolerant to 12V (see Absolute Maximum Ratings), so an external resistor pull up can be used to augment the driving capability. If using a pull up resistor in conjunction with the internal overvoltage protection function, care must be taken to avoid nuisance trips that could occur when VCC is below 2V. In that case, the controller is incapable of holding OVP low. Once an overvoltage condition is detected, normal PWM operation ceases until the ISL6561 is reset. Cycling the voltage on EN or ENLL or VCC below the POR-falling threshold will reset the controller. Cycling the VID codes will not reset the controller. Overcurrent Protection ISL6561 has two levels of overcurrent protection. Each phase is protected from a sustained overcurrent condition on a delayed basis, while the combined phase currents are protected on an instantaneous basis. In individual overcurrent protection mode, the ISL6561 continuously compares the current of each channel with the same 100A reference current. If any channel current exceeds the reference current continuously for eight consecutive cycles, the comparator triggers the converter to shutdown. At the beginning of overcurrent shutdown, the controller places all PWM signals in a high-impedance state commanding the Intersil MOSFET driver ICs to turn off both upper and lower MOSFETs. The system remains in this state a period of 4096 switching cycles. If the controller is still enabled at the end of this wait period, it will attempt a soft start. If the fault remains, trip-retry cycles continue indefinitely (as shown in Figure 12) until either controller is disabled or the fault is cleared. Note that the energy delivered during trip-retry cycling is much less than during full-load operation, so there, there is no thermal hazard during this kind of operation. General Design Guide This design guide is intended to provide a high-level explanation of the steps necessary to create a multi-phase power converter. It is assumed that the reader is familiar with many of the basic skills and techniques referenced below. In addition to this guide, Intersil provides complete reference designs that include schematics, bills of materials, and example board layouts for all common microprocessor applications. Power Stages OUTPUT CURRENT, 50A/DIV 0A OUTPUT VOLTAGE, 500mV/DIV 0V 2ms/DIV FIGURE 12. OVERCURRENT BEHAVIOR IN HICCUP MODE. FSW = 500kHz In instantaneous protection mode, the ISL6561 takes advantage of the proportionality between the load current and the average current, IAVG to detect an overcurrent condition. See the Channel-Current Balance section for more detail on how the average current is measured. The average current is continually compared with a constant 100A reference current as shown in Figure 11. Once the average current exceeds the reference current, a comparator triggers the converter to shutdown. FN9098 Rev 6.00 November 10, 2015 The first step in designing a multi-phase converter is to determine the number of phases. This determination depends heavily on the cost analysis which in turn depends on system constraints that differ from one design to the next. Principally, the designer will be concerned with whether components can be mounted on both sides of the circuit board; whether through-hole components are permitted; and the total board space available for power-supply circuitry. Generally speaking, the most economical solutions are those in which each phase handles between 15 and 20A. All surface-mount designs will tend toward the lower end of this current range. If through-hole MOSFETs and inductors can be used, higher per-phase currents are possible. In cases where board space is the limiting constraint, current may be pushed above 30A per phase, but these designs require heat sinks and forced air to cool the MOSFETs, inductors and heat-dissipating surfaces. MOSFETs The choice of MOSFETs depends on the current each MOSFET will be required to conduct; the switching frequency; the capability of the MOSFETs to dissipate heat; and the availability and nature of heat sinking and air flow. Page 19 of 27 ISL6561 LOWER MOSFET POWER CALCULATION The calculation for heat dissipated in the lower MOSFET is simple, since virtually all of the heat loss in the lower MOSFET is due to current conducted through the channel resistance (rDS(ON)). In Equation 15, IM is the maximum continuous output current; IPP is the peak-to-peak inductor current (see Equation 1); d is the duty cycle (VOUT/VIN); and L is the per-channel inductance. I L, 2PP 1 – d I M 2 P LOW 1 = r DS ON ----- 1 – d + -------------------------------12 N (EQ. 15) An additional term can be added to the lower-MOSFET loss equation to account for additional loss accrued during the dead time when inductor current is flowing through the lower-MOSFET body diode. This term is dependent on the diode forward voltage at IM, VD(ON); the switching frequency, fS; and the length of dead times, td1 and td2, at the beginning and the end of the lower-MOSFET conduction interval respectively. I I M I PP M I PP t P LOW 2 = V D ON f S ----- t d1 + ----- – --------- d2 N- + -------2 2 N (EQ. 16) Thus the total maximum power dissipated in each lower MOSFET is approximated by the summation of PLOW,1 and PLOW,2. UPPER MOSFET POWER CALCULATION In addition to rDS(ON) losses, a large portion of the upperMOSFET losses are due to currents conducted across the input voltage (VIN) during switching. Since a substantially higher portion of the upper-MOSFET losses are dependent on switching frequency, the power calculation is more complex. Upper MOSFET losses can be divided into separate components involving the upper-MOSFET switching times; the lower-MOSFET body-diode reverserecovery charge, Qrr; and the upper MOSFET rDS(ON) conduction loss. When the upper MOSFET turns off, the lower MOSFET does not conduct any portion of the inductor current until the voltage at the phase node falls below ground. Once the lower MOSFET begins conducting, the current in the upper MOSFET falls to zero as the current in the lower MOSFET ramps up to assume the full inductor current. In Equation 17, the required time for this commutation is t1 and the approximated associated power loss is PUP,1. I M I PP t 1 P UP,1 V IN ----- ---- f N- + -------2 2 S (EQ. 17) At turn on, the upper MOSFET begins to conduct and this transition occurs over a time t2. In Equation 18, the approximate power loss is PUP,2. I M I PP t 2 P UP, 2 V IN ----- – --------- ---- f S 2 2 N A third component involves the lower MOSFET’s reverserecovery charge, Qrr. Since the inductor current has fully commutated to the upper MOSFET before the lowerMOSFET’s body diode can draw all of Qrr, it is conducted through the upper MOSFET across VIN. The power dissipated as a result is PUP,3 and is approximately (EQ. 19) P UP,3 = V IN Q rr f S Finally, the resistive part of the upper MOSFET’s is given in Equation 19 as PUP,4. The total power dissipated by the upper MOSFET at full load can now be approximated as the summation of the results from Equations 17, 18, 19 and 20. Since the power equations depend on MOSFET parameters, choosing the correct MOSFETs can be an iterative process involving 2 I M I PP2 P UP,4 r DS ON ----- d + ---------12 N (EQ. 20) repetitive solutions to the loss equations for different MOSFETs and different switching frequencies. Current Sensing Resistor The resistors connected between these pins and the respective phase nodes determine the gains in the load-line regulation loop and the channel-current balance loop as well as setting the overcurrent trip point. Select values for these resistors based on the room temperature rDS(ON) of the lower MOSFETs, DCR of inductor or additional resistor; the full-load operating current, IFL; and the number of phases, N using Equation 21. RX R ISEN = ---------------------70 10 – 6 I FL ------N (EQ. 21) In certain circumstances, it may be necessary to adjust the value of one or more ISEN resistor. When the components of one or more channels are inhibited from effectively dissipating their heat so that the affected channels run hotter than desired, chose new, smaller values of RISEN for the affected phases (see the section entitled Channel-Current Balance). Choose RISEN,2 in proportion to the desired decrease in temperature rise in order to cause proportionally less current to flow in the hotter phase. T R ISEN ,2 = R ISEN ----------2 T 1 FN9098 Rev 6.00 November 10, 2015 (EQ. 18) (EQ. 22) Page 20 of 27 ISL6561 In Equation 22, make sure that T2 is the desired temperature rise above the ambient temperature, and T1 is the measured temperature rise above the ambient temperature. While a single adjustment according to Equation 22 is usually sufficient, it may occasionally be necessary to adjust RISEN two or more times to achieve optimal thermal balance between all channels. C2 (OPTIONAL) RC If one or more of the ISEN resistors is adjusted for thermal balance, as in Equation 23, the load-line regulation resistor should be selected according to Equation 24 where IFL is the full-load operating current and RISEN(n) is the ISEN resistor connected to the nth ISEN pin. V DROOP R FB = -------------------------------I FL r DS ON RISEN n (EQ. 24) n COMPENSATING LOAD-LINE REGULATED CONVERTER The load-line regulated converter behaves in a similar manner to a peak-current mode controller because the two poles at the output-filter L-C resonant frequency split with the introduction of current information into the control loop. The final location of these poles is determined by the system function, the gain of the current signal, and the value of the compensation components, RC and CC. Since the system poles and zero are effected by the values of the components that are meant to compensate them, the solution to the system equation becomes fairly complicated. Fortunately there is a simple approximation that comes very close to an optimal solution. Treating the system as though it were a voltage-mode regulator by compensating the L-C poles and the ESR zero of the voltage-mode approximation yields a solution that is always stable with very close to ideal transient performance. FN9098 Rev 6.00 November 10, 2015 IDROOP VDIFF FIGURE 13. COMPENSATION CONFIGURATION FOR LOAD-LINE REGULATED ISL6561 CIRCUIT The feedback resistor, RFB, has already been chosen as outlined in Load-Line Regulation Resistor. Select a target bandwidth for the compensated system, f0. The target bandwidth must be large enough to assure adequate transient performance, but smaller than 1/3 of the perchannel switching frequency. The values of the compensation components depend on the relationships of f0 to the L-C pole frequency and the ESR zero frequency. For each of the three cases which follow, there is a separate set of equations for the compensation components. Compensation The two opposing goals of compensating the voltage regulator are stability and speed. Depending on whether the regulator employs the optional load-line regulation as described in Load-Line Regulation, there are two distinct methods for achieving these goals. VDROOP ISL6561 + RFB The load-line regulation resistor is labeled RFB in Figure 7. Its value depends on the desired full-load droop voltage (VDROOP in Figure 7). If Equation 21 is used to select each ISEN resistor, the load-line regulation resistor is as shown in Equation 23. (EQ. 23) COMP FB Load-Line Regulation Resistor V DROOP R FB = -----------------------–6 70 10 CC Case 1: 1 ------------------- > f 0 2 LC 2f 0 V pp LC R C = R FB ----------------------------------0.75V IN 0.75V IN C C = ----------------------------------2V PP R FB f 0 Case 2: 1 1 ------------------- f 0 < ----------------------------2C ESR 2 LC V PP 2 2 f 02 LC R C = R FB -------------------------------------------0.75 V (EQ. 25) IN 0.75V IN C C = -----------------------------------------------------------2 2 f 02 V PP R FB LC Case 3: 1 f 0 > -----------------------------2C ESR 2 f 0 V pp L R C = R FB ----------------------------------------0.75 V IN ESR 0.75V IN ESR C C C = -----------------------------------------------2V PP R FB f 0 L In Equations 25, L is the per-channel filter inductance divided by the number of active channels; C is the sum total of all output capacitors; ESR is the equivalent-series resistance of the bulk output-filter capacitance; and VPP is the peak-to-peak sawtooth signal amplitude as described in Figure 6 and Electrical Specifications. Page 21 of 27 ISL6561 26, RFB is selected arbitrarily. The remaining compensation components are then selected according to Equations 26. C2 RC CC C ESR R 1 = R FB ----------------------------------------LC – C ESR COMP R1 RFB IDROOP ISL6561 FB C1 VDIFF LC – C ESR C 1 = ----------------------------------------R FB 0.75V IN C 2 = -----------------------------------------------------------------2 2 f 0 f HF LCR FB V PP 2 FIGURE 14. COMPENSATION CIRCUIT FOR ISL6561 BASED CONVERTER WITHOUT LOAD-LINE REGULATION The optional capacitor C2, is sometimes needed to bypass noise away from the PWM comparator (see Figure 13). Keep a position available for C2, and be prepared to install a highfrequency capacitor of between 22pF and 150pF in case any leading-edge jitter problem is noted. nce selected, the compensation values in Equations 23 assure a stable converter with reasonable transient performance. In most cases, transient performance can be improved by making adjustments to RC. Slowly increase the value of RC while observing the transient performance on an oscilloscope until no further improvement is noted. Normally, CC will not need adjustment. Keep the value of CC from Equations 23 unless some performance issue is noted. The optional capacitor C2, is sometimes needed to bypass noise away from the PWM comparator (see Figure 12). Keep a position available for C2, and be prepared to install a highfrequency capacitor of between 22pF and 150pF in case any trailing edge jitter problem is noted. COMPENSATION WITHOUT LOAD-LINE REGULATION The non load-line regulated converter is accurately modeled as a voltage-mode regulator with two poles at the L-C resonant frequency and a zero at the ESR frequency. A type III controller, as shown in Figure 14, provides the necessary compensation. The first step is to choose the desired bandwidth, f0, of the compensated system. Choose a frequency high enough to assure adequate transient performance but not higher than 1/3 of the switching frequency. The type-III compensator has an extra high-frequency pole, fHF. This pole can be used for added noise rejection or to assure adequate attenuation at the erroramplifier high-order pole and zero frequencies. A good general rule is to chose fHF = 10f0, but it can be higher if desired. Choosing fHF to be lower than 10f0 can cause problems with too much phase shift below the system bandwidth. In the solutions to the compensation equations, there is a single degree of freedom. For the solutions presented in Equations FN9098 Rev 6.00 November 10, 2015 V PP 2 f 0 f HF LCR FB R C = -------------------------------------------------------------------2f 0.75 V HF LC – 1 IN 0.75V IN 2f HF LC – 1 C C = ------------------------------------------------------------------ 2 2 f 0 f HF LCR FB V PP (EQ. 26) In Equations 26, L is the per-channel filter inductance divided by the number of active channels; C is the sum total of all output capacitors; ESR is the equivalent-series resistance of the bulk output-filter capacitance; and VPP is the peak-to-peak sawtooth signal amplitude as described in Figure 6 and Electrical Specifications. Output Filter Design The output inductors and the output capacitor bank together form a low-pass filter responsible for smoothing the pulsating voltage at the phase nodes. The output filter also must provide the transient energy until the regulator can respond. Because it has a low bandwidth compared to the switching frequency, the output filter necessarily limits the system transient response. The output capacitor must supply or sink load current while the current in the output inductors increases or decreases to meet the demand. In high-speed converters, the output capacitor bank is usually the most costly (and often the largest) part of the circuit. Output filter design begins with minimizing the cost of this part of the circuit. The critical load parameters in choosing the output capacitors are the maximum size of the load step, I; the load-current slew rate, di/dt; and the maximum allowable output-voltage deviation under transient loading, VMAX. Capacitors are characterized according to their capacitance, ESR, and ESL (equivalent series inductance). At the beginning of the load transient, the output capacitors supply all of the transient current. The output voltage will initially deviate by an amount approximated by the voltage drop across the ESL. As the load current increases, the voltage drop across the ESR increases linearly until the load current reaches its final value. The capacitors selected must have sufficiently low ESL and ESR so that the total output- Page 22 of 27 ISL6561 di V ESL ----- + ESR I dt (EQ. 27) The filter capacitor must have sufficiently low ESL and ESR so that V < VMAX. Most capacitor solutions rely on a mixture of high-frequency capacitors with relatively low capacitance in combination with bulk capacitors having high capacitance but limited high-frequency performance. Minimizing the ESL of the high-frequency capacitors allows them to support the output voltage as the current increases. Minimizing the ESR of the bulk capacitors allows them to supply the increased current with less output voltage deviation. The ESR of the bulk capacitors also creates the majority of the output-voltage ripple. As the bulk capacitors sink and source the inductor ac ripple current (see Interleaving and Equation 2), a voltage develops across the bulk-capacitor ESR equal to IC,PP (ESR). Thus, once the output capacitors are selected, the maximum allowable ripple voltage, VPP(MAX), determines the lower limit on the inductance. V – N V OUT V OUT IN L ESR -----------------------------------------------------------f S V IN V PP MAX (EQ. 28) Since the capacitors are supplying a decreasing portion of the load current while the regulator recovers from the transient, the capacitor voltage becomes slightly depleted. The output inductors must be capable of assuming the entire load current before the output voltage decreases more than VMAX. This places an upper limit on inductance. Equation 29 gives the upper limit on L for the cases when the trailing edge of the current transient causes a greater output-voltage deviation than the leading edge. Equation 30 addresses the leading edge. Normally, the trailing edge dictates the selection of L because duty cycles are usually 2NCVO L -------------------- V MAX – I ESR I 2 (EQ. 29) Input Supply Voltage Selection The VCC input of the ISL6561 can be connected either directly to a +5V supply or through a current limiting resistor to a +12V supply. An integrated 5.8V shunt regulator maintains the voltage on the VCC pin when a +12V supply is used. A 300 resistor is suggested for limiting the current into the VCC pin to a worst-case maximum of approximately 25mA. Switching Frequency There are a number of variables to consider when choosing the switching frequency, as there are considerable effects on the upper-MOSFET loss calculation. These effects are outlined in MOSFETs, and they establish the upper limit for the switching frequency. The lower limit is established by the requirement for fast transient response and small outputvoltage ripple as outlined in Output Filter Design. Choose the lowest switching frequency that allows the regulator to meet the transient-response requirements. 1000 RT (k) voltage deviation is less than the allowable maximum. Neglecting the contribution of inductor current and regulator response, the output voltage initially deviates by an amount 100 10 10 Switching frequency is determined by the selection of the frequency-setting resistor, RT (see the figures labeled Typical Application on pages 3 and 6). Figure 15 and Equation 31 are provided to assist in selecting the correct value for RT. · (EQ. 30) less than 50%. Nevertheless, both inequalities should be evaluated, and L should be selected based on the lower of the two results. In each equation, L is the per-channel inductance, C is the total output capacitance, and N is the number of active channels. FN9098 Rev 6.00 November 10, 2015 10000 FIGURE 15. RT vs SWITCHING FREQUENCY R T = 1.0203 10 1.25 NC L -------------------------- V MAX – I ESR V IN – V O I 2 100 1000 SWITCHING FREQUENCY (kHz) 10.6258- 1.03167 log f S – 1200 (EQ. 31) Input Capacitor Selection The input capacitors are responsible for sourcing the ac component of the input current flowing into the upper MOSFETs. Their RMS current capacity must be sufficient to handle the ac component of the current drawn by the upper MOSFETs which is related to duty cycle and the number of active phases. Page 23 of 27 ISL6561 and off. Select low ESL ceramic capacitors and place one as close as possible to each upper MOSFET drain to minimize board parasitic impedances and maximize suppression. 0.3 0.2 0.1 IL,PP = 0 IL,PP = 0.5 IO IL,PP = 0.75 IO 0 0 0.2 0.4 0.6 0.8 1.0 DUTY CYCLE (VO / VIN) FIGURE 16. NORMALIZED INPUT-CAPACITOR RMS CURRENT vs DUTY CYCLE FOR 2-PHASE CONVERTER INPUT-CAPACITOR CURRENT (IRMS / IO) INPUT-CAPACITOR CURRENT (IRMS / IO) 0.3 IL,PP = 0 IL,PP = 0.5 IO IL,PP = 0.25 IO IL,PP = 0.75 IO 0.2 0.1 0 0 0.2 0.4 0.6 0.8 1.0 DUTY CYCLE (VO / VIN) IL,PP = 0 IL,PP = 0.5 IO IL,PP = 0.25 IO IL,PP = 0.75 IO FIGURE 18. NORMALIZED INPUT-CAPACITOR RMS CURRENT VS DUTY CYCLE FOR 4-PHASE CONVERTER MULTI-PHASE RMS IMPROVEMENT 0.2 0.1 0 0 0.2 0.4 0.6 0.8 1.0 DUTY CYCLE (VO / VIN) FIGURE 17. NORMALIZED INPUT-CAPACITOR RMS CURRENT VS DUTY CYCLE FOR 3-PHASE CONVERTER For a two phase design, use Figure 16 to determine the input-capacitor RMS current requirement given the duty cycle, maximum sustained output current (IO), and the ratio of the per phase peak-to-peak inductor current (IL,PP) to IO. Select a bulk capacitor with a ripple current rating which will minimize the total number of input capacitors required to support the RMS current calculated. The voltage rating of the capacitors should also be at least 1.25 times greater than the maximum input voltage. Figures 17 and 18 provide the same input RMS current information for three and four phase designs respectively. Use the same approach to selecting the bulk capacitor type and number as described above. Low capacitance, high-frequency ceramic capacitors are needed in addition to the bulk capacitors to suppress leading and falling edge voltage spikes. The result from the high current slew rates produced by the upper MOSFETs turn on FN9098 Rev 6.00 November 10, 2015 Figure 19 is provided as a reference to demonstrate the dramatic reductions in input-capacitor RMS current upon the implementation of the multi-phase topology. For example, compare the input rms current requirements of a two-phase converter versus that of a single phase. Assume both converters have a duty cycle of 0.25, maximum sustained output current of 40A, and a ratio of IC,PP to IO of 0.5. The single phase converter would require 17.3 Arms current capacity while the two-phase converter would only require 10.9 Arms. The advantages become even more pronounced when output current is increased and additional phases are added to keep the component cost down relative to the single phase approach. 0.6 INPUT-CAPACITOR CURRENT (IRMS / IO) INPUT-CAPACITOR CURRENT (IRMS / IO) 0.3 0.4 0.2 IL,PP = 0 IL,PP = 0.5 IO IL,PP = 0.75 IO 0 0 0.2 0.4 0.6 0.8 1.0 DUTY CYCLE (VO / VIN) FIGURE 19. NORMALIZED INPUT-CAPACITOR RMS CURRENT VS DUTY CYCLE FOR SINGLE-PHASE CONVERTER Page 24 of 27 ISL6561 Layout Considerations The following layout strategies are intended to minimize the impact of board parasitic impedances on converter performance and to optimize the heat-dissipating capabilities of the printed-circuit board. These sections highlight some important practices which should not be overlooked during the layout process. The ISL6561 can be placed off to one side or centered relative to the individual phase switching components. Routing of sense lines and PWM signals will guide final placement. Critical small signal components to place close to the controller include the ISEN resistors, RT resistor, feedback resistor, and compensation components. Component Placement Bypass capacitors for the ISL6561 and HIP660X driver bias supplies must be placed next to their respective pins. Trace parasitic impedances will reduce their effectiveness. Within the allotted implementation area, orient the switching components first. The switching components are the most critical because they carry large amounts of energy and tend to generate high levels of noise. Switching component placement should take into account power dissipation. Align the output inductors and MOSFETs such that space between the components is minimized while creating the PHASE plane. Place the Intersil MOSFET driver IC as close as possible to the MOSFETs they control to reduce the parasitic impedances due to trace length between critical driver input and output signals. If possible, duplicate the same placement of these components for each phase. Next, place the input and output capacitors. Position one high-frequency ceramic input capacitor next to each upper MOSFET drain. Place the bulk input capacitors as close to the upper MOSFET drains as dictated by the component size and dimensions. Long distances between input capacitors and MOSFET drains results in too much trace inductance and a reduction in capacitor performance. Locate the output capacitors between the inductors and the load, while keeping them in close proximity to the microprocessor socket. FN9098 Rev 6.00 November 10, 2015 Plane Allocation and Routing Dedicate one solid layer, usually a middle layer, for a ground plane. Make all critical component ground connections with vias to this plane. Dedicate one additional layer for power planes; breaking the plane up into smaller islands of common voltage. Use the remaining layers for signal wiring. Route phase planes of copper filled polygons on the top and bottom once the switching component placement is set. Size the trace width between the driver gate pins and the MOSFET gates to carry 1A of current. When routing components in the switching path, use short wide traces to reduce the associated parasitic impedances. Page 25 of 27 ISL6561 Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to the web to make sure that you have the latest revision. DATE REVISION November 10, 2015 FN9098.6 CHANGE - Ordering Information Table on page 2. - Added Revision History. - Added About Intersil Verbiage. - Updated POD L40.6x6 to latest revision changes are as follow: -Revision 1 to Revision 2 Changes: converted to new template. -Revision 2 to Revision 3 Changes: Corrected Note 4: Dimension b is measured between 0.15mm and 0.3mm, not 0.015mm and 0.3mm. About Intersil Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets. For the most updated datasheet, application notes, related documentation and related parts, please see the respective product information page found at www.intersil.com. You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask. Reliability reports are also available from our website at www.intersil.com/support © Copyright Intersil Americas LLC 2002-2015. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN9098 Rev 6.00 November 10, 2015 Page 26 of 27 ISL6561 Package Outline Drawing L40.6x6 40 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE Rev 3, 10/06 4X 4.5 6.00 36X 0.50 A B 6 PIN 1 INDEX AREA 6 PIN #1 INDEX AREA 40 31 30 1 6.00 4 . 10 ± 0 . 15 21 10 0.15 (4X) 11 20 TOP VIEW 0.10 M C A B 40X 0 . 4 ± 0 . 1 4 0 . 23 +0 . 07 / -0 . 05 BOTTOM VIEW SEE DETAIL "X" 0.10 C 0 . 90 ± 0 . 1 ( C BASE PLANE ( 5 . 8 TYP ) SEATING PLANE 0.08 C SIDE VIEW 4 . 10 ) ( 36X 0 . 5 ) C 0 . 2 REF 5 ( 40X 0 . 23 ) 0 . 00 MIN. 0 . 05 MAX. ( 40X 0 . 6 ) DETAIL "X" TYPICAL RECOMMENDED LAND PATTERN NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal ± 0.05 4. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 5. Tiebar shown (if present) is a non-functional feature. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 indentifier may be either a mold or mark feature. FN9098 Rev 6.00 November 10, 2015 Page 27 of 27