Jumbo-LED ELJ-910-628 16.11.2007 rev. 05 Radiation Type Technology Case Infrared 2W AlGaAs/AlGaAs Plastic lens, metal case High-power infrared LED in an aluminium case with thread socket, for easy handling and heat sink mounting 1,5 Ø11 Ø1,7 Ø16 Ø12,5 Description 4,5 5,08 7,9 Outline: 2 H = 12.4 mm (± 0.5) 8 D = 16.0 mm (± 0.5) Applications Medical appliances, remote control and light barriers, measurement applications and security systems 13 Thread M10 1 2 Pin 1 – cathode Pin 2 – anode M10 Absolute Maximum Ratings at Tamb = 25°C, on heat sink (S ≥ 200 cm²), unless otherwise specified Parameter Test сonditions Symbol Value Unit on heat sink IF 1.0 A tp≤10 µs, f≤500 Hz IFM 2,0 A Power dissipation on heat sink P 1,7 W Operating temperature range on heat sink Tamb -25 to +100 °C Storage temperature range on heat sink Tstg -25 to +100 °C Junction temperature on heat sink Tj 100 °C Typ Max Unit 1.7 V DC forward current Peak forward current Electrical Characteristics at Tamb = 25°C, on heat sink (S ≥ 200 cm²), unless otherwise specified Test Parameter Symbol Min conditions Forward voltage IF = 350 mA VF 1.4 Forward voltage* IF = 1000 mA VF 1.7 V Switching time IF = 350 mA tr, tf 20 ns Reverse voltage IR = 10 µA VR 10 K/W Thermal resistance junction-case *only recommended on optimal heat sink RthJC 5 We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications.All operating parameters must be validated for each customer application by the customer. EPIGAP Optoelektronik GmbH, D-12555 Berlin, Köpenicker Str.325 b, Haus 201 1 of 5 Tel.: +49-30-6576 2543, Fax : +49-30-6576 2545 Jumbo-LED ELJ-910-628 16.11.2007 rev. 05 Optical Characteristics at Tamb = 25°C, on heat sink (S ≥ 200 cm²), unless otherwise specified Test Parameter Symbol Min conditions Typ Max Unit Radiant power IF = 350 mA Φe Radiant power* IF = 1000 mA Φe Radiant intensity IF = 350 mA Ιe Radiant intensity* IF = 1000 mA Ιe Peak wavelength IF = 350 mA λp Spectral bandwidth at 50% IF = 350 mA ∆λ0.5 60 nm Viewing angle IF = 350 mA ϕ 17 deg 17 160 900 23 mW 56 mW 205 mW/sr 500 mW/sr 910 920 nm *only recommended on optimal heat sink Note: All measurements carried out withEPIGAP equipment, on blank aluminium heat sink, S = 180 cm², passive cooling. Measurement results and curve characteristics obtained with other heat sinks may differ. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications.All operating parameters must be validated for each customer application by the customer. EPIGAP Optoelektronik GmbH, D-12555 Berlin, Köpenicker Str.325 b, Haus 201 2 of 5 Tel.: +49-30-6576 2543, Fax : +49-30-6576 2545 Jumbo-LED ELJ-910-628 16.11.2007 rev. 05 We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications.All operating parameters must be validated for each customer application by the customer. EPIGAP Optoelektronik GmbH, D-12555 Berlin, Köpenicker Str.325 b, Haus 201 3 of 5 Tel.: +49-30-6576 2543, Fax : +49-30-6576 2545 Jumbo-LED ELJ-910-628 16.11.2007 rev. 05 Remarks concerning optical radiation safety* Up to a forward current of 500 mA, and continuous operation, this LED may be classified as LED product Class 1 , according to standard IEC 60825-1:A2. Class 1 products are safe to eyes and skin under reasonably predictable conditions. This implicates a direct observation of the light beam by means of optical instruments. When driven with higher continuous forward current, (up to max. DC current), this product should be classified as LED product Class 1M , according to standard IEC 60825-1:A2. Class 1M products are safe to eyes and skin under normal conditions, including when users view the light beam directly. Class 1M products produce either a highly divergent beam or a large diameter beam. Therefore only a small part of the whole light beam can enter the eye. However, such optical products can be harmful to the retina if the beam is viewed using magnifying optical instruments. Therefore, users should not incorporate optics that could concentrate the output into the eyes. *Note: Safety classification of an optical component mainly depends on the intended application and the way the component is being used. Furthermore, all statements made to classification are based on calculations and are only valid for this LED "as it is", and at continuous operation. Using pulsed current or altering the light beam with additional optics may lead to different safety classifications. Therefore these remarks should be taken as recommendation and guideline only. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications.All operating parameters must be validated for each customer application by the customer. EPIGAP Optoelektronik GmbH, D-12555 Berlin, Köpenicker Str.325 b, Haus 201 4 of 5 Tel.: +49-30-6576 2543, Fax : +49-30-6576 2545 Jumbo-LED ELJ-910-628 16.11.2007 rev. 05 Handling precautions To prevent damage to the LED during soldering and assembly, following precautions have to be taken into account. a) The bending point of the lead frame should be located at least 2.5 mm away from the body. b) While bending, the base of the lead frame has to be fixed with radio pliers or similar. c) To ensure an adequate strain relief, the lead frames have to be firmly fixed during soldering. d) Avoid any torsion or tensile loading of the lead frames, especially when they have been heated after being soldered. e) LEDs are static sensitive devices, so adequate handling precautions have to be taken, e.g. wearing grounding wrist straps. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications.All operating parameters must be validated for each customer application by the customer. EPIGAP Optoelektronik GmbH, D-12555 Berlin, Köpenicker Str.325 b, Haus 201 5 of 5 Tel.: +49-30-6576 2543, Fax : +49-30-6576 2545