Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Ceramic Filters (CERAFILr) for FM Receivers CERAMIC FILTERS (CERAFILr) Murata Manufacturing Co., Ltd. Cat.No.P61E-7 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. CONTENTS 1 CERAFILr and "CERAFIL" in this catalog are the trademarks of Murata Manufacturing Co., Ltd. Part Numbering 1 2 P61E7.pdf 01.10.17 2 CERAFILr Chip Type SFECV Series 3 Chip CERAFILr SFECV Series Notice 6 CERAFILr Small Chip Type SFECS Series 7 Chip CERAFILr SFECS Series Notice 10 3 CERAFILr Standard Lead Type 11 4 CERAFILr Low-loss Type 14 5 CERAFILr Low-profile Type 17 6 CERAFILr Lower Spurious Response Type 20 7 CERAFILr Wider Band-width Type 23 8 CERAFILr Narrow Band Type 25 9 CERAFILr For FM -IF Tuners 28 10 CERAFILr Three-Elements Type SFTLA Series 33 Lead Type CERAFILr Test Circuit and Characteristics Data 36 Lead Type CERAFILr Characteristics Data and Notice 37 11 12 13 Discriminators Chip Type CDACV Series 38 Chip Type Discriminators CDACV Series Notice 41 Discriminators Chip Low-profile Type CDSCA Series 42 Chip Type Discriminators CDSCA Series Notice 44 Discriminators CDALA Series 45 Lead Type Discriminators Notice 49 Packaging 50 Test Circuit of Ceramic Discriminator 53 Example of Appllied Circuit 54 Recycled Paper 2 3 4 5 6 7 8 9 10 11 12 13 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. o Part Numbering P61E7.pdf 01.10.17 structure of the "Global Part Numbers" that have been adopted since June 2001 and the meaning of each code are described herein. ( The ) If you have any questions about details, inquire at your usual Murata sales office or distributor. CERAFILr for FM (Global Part Number) SF E LA q w e 10M7 FAA0 r t -R0 y qProduct ID tProduct Specification Product ID Product Specification Code SF Ceramic Filters FAA0 wOscillation/Numbers of Element Four-digit alphanumerics express pass-bandwidth, center frequency tolerance, rank, series, others. Code Oscillation/Numbers of Element E 2 Elements Thickness Expander mode T 3 Elements Thickness Expander mode Code K 2 Elements Thickness Expander mode (2nd Harmonic) -B0 Bulk -R0 Plastic Taping ø180mm V 2 Elements Thickness Expander mode (3rd Over Tone) -R1 Plastic Taping ø330mm -A0 1500pcs. /Radial Taping H0=18mm -A1 1000pcs. /Radial Taping H0=18mm eStructure/Size Code Structure/Size Lp Lead Type Cp Chip Type yPackaging Packaging Radial taping is applied to lead type and plastic taping to chip type. With non-standard products, two-digit alphanumerics indicating "Individual Specification" is added between "tProduct Specification" and "yPackaging". p is expressed "A" or subsequent code, which indicates the size. rNominal Center Frequency Expressed by four-digit alphanumerics. The unit is in hertz (MHz). Decimal point is expressed by capital letter "M". Discriminators for FM (Global Part Number) CD A LA 10M7 GA 001 -R0 q w e r t y u qProduct ID tProduct Specification Product ID CD Discriminators Code Product Specification GA Two-digit alphanumerics express type, center frequency, rank, others wOscillation Code Oscillation A Thickness Expander mode yIC Code IC 001 Applicable IC Control Code eStructure/Size Structure/Size Lp Lead Type Code Cp Chip Type -B0 Bulk -A0 Radial Taping H0=18mm -R0 Plastic Taping (ø180mm) -R1 Plastic Taping (ø330mm) p is expressed "A" or subsequent code, which indicates the size. rNominal Center Frequency Expressed by four-digit alphanumerics . The unit is in hertz (MHz). Decimal point is expressed by capital letter "M". 2 uPackaging Code Packaging Radial taping is applied to lead type and plastic taping to chip type. With non-standard products, an alphanumerics indicating "Individual Specification" is added between "yIC" and "uPackaging". Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Ceramic Filters (CERAFILr) for FM Receivers 1 CERAFILr Chip Type SFECV Series 6.9±0.3 4.05±0.4 SFECV10M7 series for FM-receivers are monolithic type ceramic filters which utilize the energy trapped thickness vibration-mode of the piezoelectric ceramic. By taking advantage of the very low profile, new SFECV series and PFWCC(kHz filter for AM receiver) enable costomers to make AM/FM set so thin, and it can be of help to the total chip circuit. 2.9±0.3 1.2±0.5 1.2±0.3 (2) (1) Bottom Electrode Side Electrode 1.5±0.2 ■ Features : Marking 1.0±0.5 1. Super-thin. Only 1.5mm. The most suitable ceramic filter available for thinning substrates. 2. Heat resistant. Reflow soldering can be performed because of its excellent heat resistance. 3. Piezoelectric element is connected in the sandwich shape by heat resistant substrate, thus it has excellent mechanical strength, and it is suitable for automatic mounting. 4. Various bandwidths are available. Select a suitable type in accordance with the desired selectivity. 5. Electrical characteristics are the same as conventional "CERAFIL". 1.5±0.2 * * * (3) 1.2±0.5 1.0±0.5 1.0±0.5 ** : EIAJ Monthly Code ** : Center Frequency Rank Code (1) : Input (2) : Ground (3) : Output (in mm) ■ Applications 1. Small, thin radios 2. Automotive radios 3. Headphone steros Center Frequency (fo) (MHz) 3dB Bandwidth (kHz) Attenuation (kHz) Insertion Loss (dB) Spurious Attenuation (dB) SFECV10M7KA00-R0 10.700 ±30kHz within110 ±30kHz 320 max. within6.0 ±2.0dB 35 min. SFECV10M7JA00-R0 10.700 ±30kHz within150 ±40kHz 380 max. 10.0 max. 30 min. SFECV10M7HA00-R0 10.700 ±30kHz within180 ±40kHz 470 max. within4.0 ±2.0 dB 35 min. SFECV10M7GA00-R0 10.700 ±30kHz within230 ±50kHz 510 max. within3.5 ±2.0 dB 35 min. SFECV10M7FA00-R0 10.700 ±30kHz within280 ±50kHz 590 max. within3.0 ±2.0 dB 35 min. Part Number Area of Attenuation : [within 20dB] Area of Spurious Attenuation : [within 9MHz to 12MHz] Center frequency(fo) defined by the center of 3dB bandwidth. ■ Center Frequency Rank Code CODE 30kHz Step 25kHz Step D 10.64MHz±30kHz 10.650MHz±25kHz B 10.67MHz±30kHz 10.675MHz±25kHz A 10.70MHz±30kHz 10.700MHz±25kHz C 10.73MHz±30kHz 10.725MHz±25kHz E 10.76MHz±30kHz 10.750MHz±25kHz Z Combination A,B,C,D,E M Combination A,B,C 3 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. ■ Frequency Characteristics SFECV10M7JA00-R0 0 0 10 10 20 20 Attenuation (dB) 30 40 30 40 50 50 60 60 70 9.700 10.200 10.700 Frequency (MHz) 11.200 70 9.700 11.700 1 5.50 2 5.00 3 4.50 4 4.00 5 3.50 6 3.00 10.600 10.700 Frequency (MHz) 10.800 11.200 11.700 0 5.50 1 5.00 2 4.50 3 4.00 4 3.50 5 3.00 6 2.50 7 2.50 7 Attenuation (dB) 6.00 10.500 10.700 Frequency (MHz) SFECV10M7GA00-R0 0 G.D.T. (µsec.) Attenuation (dB) SFECV10M7HA00-R0 10.200 10.500 10.600 10.900 10.700 Frequency (MHz) 10.800 10.900 G.D.T. (µsec.) Attenuation (dB) SFECV10M7KA00-R0 2.00 5.00 1 4.50 2 4.00 3 3.50 4 3.00 5 2.50 6 2.00 7 10.500 10.600 10.700 Frequency (MHz) 10.800 10.900 G.D.T. (µsec.) Attenuation (dB) SFECV10M7FA00-R0 0 1.50 ■ Frequency Characteristics (Spurious) SFECV10M7KA00-R0 SFECV10M7JA00-R0 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) 1 P61E7.pdf 01.10.17 30 40 30 40 50 50 60 60 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 Continued on the following page. 4 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Continued from the preceding page. ■ Frequency Characteristics (Spurious) 10 10 20 20 30 40 30 40 50 50 60 60 70 8.700 9.700 10.700 Frequency (MHz) 1 SFECV10M7GA00-R0 0 Attenuation (dB) Attenuation (dB) SFECV10M7HA00-R0 0 11.700 12.700 11.700 12.700 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 SFECV10M7FA00-R0 0 10 Attenuation (dB) 20 30 40 50 60 70 8.700 9.700 10.700 Frequency (MHz) ■ Standard Land Pattern Dimensions 1.2 1.2 ■ Test Circuit 1.2 (1): Input (2): Ground (3): Output R1 (2) Rg 4.0 (3) (1) E1 R2 C2 E2 S.S.G. =-10dBm 1.65 1.65 2.85 2.85 Land (in mm) RF Voltmeter Rg = 50Ω R1 = 280Ω ±5% R2 = 330Ω ±5% C2 = 10 ± 2 pF (Including stray capacitance and Input capacitance of RF Volt Meter) E1 : S.S.G. S.S.G. Output Voltage 5 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Chip CERAFILr SFECV Series Notice 1 ■ Notice (Soldering and Mounting) 1. Standard Reflow Soldering Condition (1) Reflow 5sec. 240 Temperaturu(°C) 230 Gradual Cooling 150 60 30 Time(sec.) (2) Soldering Iron Lead terminal is directly contacted with the tip of soldering iron of 280±5˚C for 3.0±0.5 seconds. 2. Wash The component cannot be withstand washing. ■ Notice (Handling) 1. The component will be damaged when an excessive stress is applied. 2. The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. 3. Design layout of components on the PC board to minimize the stress imposed on the warp or flexure of the board. 4. After installing chips, if solder is excessively applied to the circuit board, mechanical stress will cause destruction resistance characteristics to lower. To prevent this, be extremely careful in determining shape and dimension before designing the circuit board diagram. 5. When the positioning claws and pick up nozzle are worn, the load is applied to the chip while positioning is concentrated to one positioning accuracy, etc. Careful checking and maintenance are necessary to prevent unexpected trouble. 6. When correcting chips with a soldering iron, the tip of the soldering iron should not directly touch the chip component. Depending on the soldering conditions, the effective area of terminations may be reduced. the use of solder containing Ag should be done to prevent the electrode erosion. 7. Do not clean or wash the component as it is not hermetically sealed. 8. In case of covering filter with over coat, conditions such as material of resin, cure temperature, and so on should be evaluated well. 9. Do not use strong acidity flux, more than 0.2wt% chlorine content, in re-flow soldering. 10. Accurate test circuit values are required to measure electrical characteristics.It may be a cause of miscorrelation if there is any deviation, especially stray capacitance, from the test circuit in the specification. 6 [Component direction] Put the component lateral to the direction in which stress acts. [Component layout close to board] Perforation A B Slit C Susceptibility to stress is in the order of : A>C>B Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Ceramic Filters (CERAFILr) for FM Receivers CERAFILr Small Chip Type SFECS Series 2 0.85T0.3 FA Input electrode marker 0-0.3 0.6T0.3 0.4 W0.3 Y0.2 0.6T0.3 0-0.3 (1.35) (1.35) 0.7T0.3 0.7T0.3 0.7T0.3 0.85T0.3 1.4T0.1 3.10T0.2 3.45T0.2 SFECS10M7 series for FM-receivers are small, high performance and super thin (1.4mm) filters. Piezoelectric element is connected in the sandwich shape by ceramics substrate. They have 1.4mm thickness and small mounting area. (3.5x3.1mm) New SFECS series and PFWCC(kHz filter for AM receiver) enable customers to make AM/FM set so thin and small sized. (1) (2) (3) (4) (1.30) 0-0.3 (1.30) 0-0.3 (1) : Input (2) : Ground (3) : Float (Signal line) (4) : Output (*) : Reference : EIAJ Monthly Code (in mm) ■ Features 1. The filters are mountable by automatic placers. 2. They are slim, at only 1.4mm thickness, and have a small mounting area (3.5x3.1mm) enabling flexible PCB design. 3. Various bandwidths are available. Select a suitable type in accordance with the desires selectivity. 4. Operating temperature range : -20 to +80 (degree C) Storage temperature range : -40 to +85 (degree C) ■ Applications 1. Small, thin radios 2. Headphone stereos Center Frequency (fo) (MHz) 3dB Bandwidth (kHz) Attenuation (kHz) Insertion Loss (dB) Spurious Attenuation (dB) SFECS10M7HA00-R0 10.700 ±30kHz within180 ±40kHz 470 max. within4.5 ±2.0 dB 30 min. SFECS10M7GA00-R0 10.700 ±30kHz within230 ±50kHz 510 max. within3.5 ±2.0 dB 30 min. SFECS10M7FA00-R0 10.700 ±30kHz within280 ±50kHz 590 max. within3.0 ±2.0 dB 30 min. Part Number Area of Attenuation : [within 20dB] Area of Spurious Attenuation : [within 9MHz to 12MHz] Center frequency(fo) defined by the center of 3dB bandwidth. ■ Center Frequency Rank Code CODE 30kHz Step 25kHz Step D 10.64MHz±30kHz 10.650MHz±25kHz B 10.67MHz±30kHz 10.675MHz±25kHz A 10.70MHz±30kHz 10.700MHz±25kHz C 10.73MHz±30kHz 10.725MHz±25kHz E 10.76MHz±30kHz 10.750MHz±25kHz Z Combination A,B,C,D,E M Combination A,B,C 7 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 ■ Frequency Characteristics SFECS10M7HA00-R0 SFECS10M7GA00-R0 0 5.60 5.00 4.80 5.40 2 5.20 2 2 4.60 4.60 4.40 6 4.40 Attenuation (dB) 4.80 4 G.D.T. (µsec.) Attenuation (dB) 5.00 4 4.20 4.00 6 3.80 4.20 3.60 4.00 8 8 3.40 3.80 10 10.500 10.600 10.700 10.800 10.900 3.20 3.60 10 10.500 10.600 Frequency (MHz) 10.700 10.800 10.900 3.00 Frequency (MHz) SFECS10M7FA00-R0 0 4.60 4.40 2 4.20 3.80 3.60 6 3.40 G.D.T. (µsec.) Attenuation (dB) 4.00 4 3.20 8 3.00 2.80 10 10.500 10.600 10.700 10.800 10.900 2.60 Frequency (MHz) ■ Frequency Characteristics (Spurious) SFECS10M7GA00-R0 0 0 10 10 Attenuation (dB) Attenuation (dB) SFECS10M7HA00-R0 20 30 40 50 8.700 9.700 10.700 11.700 12.700 0 Attenuation (dB) 10 20 30 40 9.700 10.700 Frequency (MHz) 50 8.700 9.700 10.700 Frequency (MHz) SFECS10M7FA00-R0 8 30 40 Frequency (MHz) 50 8.700 20 11.700 12.700 11.700 12.700 G.D.T. (µsec.) 0 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. ■ Test Circuit 0.1 ■ Standard Land Pattern Dimensions (3) 0.3 R1 1.05 0.1 (4) (2) 0.1 E1 0.1 R2 C2 E2 RF Voltmeter S.S.G. =-10dBm 1.05 (3) 0.1 0.3 (2) 2 (4) Rg 1.40 0.3 (1) (1) P61E7.pdf 01.10.17 0.1 0.8 0.6 0.8 0.6 0.8 (1) : Input (2) : Ground (3) : Float Signal Line (4) : Out put It shows solder resist land pattern. (in mm) Rg=50Ω R1=280Ω R2=330Ω C2=10pF (Including stray capacitance and Input capacitance of RF Voltmeter) (1) : Input (2) : Ground (3) : Float (4) : Output 9 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Chip CERAFILr SFECS Series Notice ■ Notice (Soldering and Mounting) 1. Standard Reflow Soldering Condition (1) Reflow Temperature (˚C) 2 Peak (240˚C max.) 240 200 Pre-heating (120-170˚C) 100 Heating (200˚C) Gradual Cooling (2) Soldering Iron Filter shall be soldered at 280±5˚C for 3.0±0.5 seconds. The soldering iron shall not touch the filter white soldering. 30 sec. min. 60-120 sec. 30 sec. max. 120 sec. min. 2. Wash The component cannot be withstand washing. ■ Notice (Handling) 1. The component will be damaged when an excessive stress is applied. 2. The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. 3. Design layout of components on the PC board to minimize the stress imposed on the warp or flexure of the board. 4. After installing chips, if solder is excessively applied to the circuit board, mechanical stress will cause destruction resistance characteristics to lower. To prevent this, be extremly careful in determining shape and dimension before designing the circuit board diagram. 5. When the positioning claws and pick up nozzle are worn, the load is applied to the chip while positioning is concentrated to one positioning accuracy, etc. Careful checking and maintenance are necessary to prevent unexpected trouble. 6. When correcting chips with a soldering iron, the tip of the soldering iron should not directly touch the chip component. Depending on the soldering conditions, the effective area of terminations may be reduced. The use of solder containing Ag should be done to prevent the electrode erosion. 7. Do not clean or wash the component as it is not hermetically sealed. 8. In case of covering filter with over coat, conditions such as material of resin, cure temperature, and so on should be evaluated well. 9. Do not use strong acidity flux, more than 0.2wt% chlorine content, in re-flow soldering. 10. Accurate test circuit values are required to measure electrical characteristics. It may be a cause of mis-correlation if there is any deviation, especially stray capacitance, from the test circuit in the specification. 10 [Component layout close to board] Perforation B A Slit C Susceptibility to stress is in the order of : A>C>B Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Ceramic Filters (CERAFILr) for FM Receivers CERAFILr Standard Lead Type 7.0±2.0 SFELA10M7 series for FM-receivers are monolithic type ceramic filters which use the energy trapped thickness vibration-mode of the piezoelectric ceramic. MARKING ■ Features 3 7.0±2.0 EIAJ CODE 0.5±0.1 2.5±0.2 2.5±0.2 3.0±1.0 SFELA10M7HA00-B0 0.3±0.1 (3) (1) : Input (2) : Ground (3) : Output (in mm) (1) (2) 7.0±2.0 MARKING EIAJ CODE 7.0±2.0 1. These miniature filters have high mechanical strength. 2. Low loss, favorable waveform symmetry, and high selectivity. 3. Various band widths are available for applications in wide to narrow bands. 4. Small dispersion and stable characteristics. 5. Change in center frequency is typically within ±30ppm/(degree C) at -20 to +80 (degree C). 6. High reliability. 5.0±1.0 1.38±0.2 1.7±0.1 5.0±1.0 1.38±0.2 1.7±0.1 0.5±0.1 3.0±1.0 SFELA10M7GA00-B0 0.3±0.1 2.5±0.2 2.5±0.2 (3) (1) : Input (2) : Ground (3) : Output (in mm) (1) (2) 7.0±2.0 EIAJ CODE 7.0±2.0 MARKING 5.0±1.0 1.38±0.2 1.7±0.1 0.5±0.1 3.0±1.0 SFELA10M7FA00-B0 0.3±0.1 2.5±0.2 2.5±0.2 (3) Center Frequency (fo) (MHz) 3dB Bandwidth (kHz) Attenuation (kHz) SFELA10M7HA00-B0 10.700 ±30kHz within180 ±40kHz SFELA10M7GA00-B0 10.700 ±30kHz within230 ±50kHz SFELA10M7FA00-B0 10.700 ±30kHz within280 ±50kHz Part Number (2) (1) : Input (2) : Ground (3) : Output (in mm) (1) Insertion Loss (dB) Spurious Attenuation (dB) 520 max. 7.0 max. 40 min. 570 max. within4.0 ±2.0dB 40 min. 650 max. within4.0 ±2.0dB 30 min. Area of Attenuation : [within 20dB] Area of Spurious Attenuation : [within 9MHz to 12MHz] Center frequency(fo) defined by the center of 3dB bandwidth. 11 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 ■ Center Frequency Rank Code 3 CODE 30kHz Step 25kHz Step D 10.64MHz±30kHz 10.650MHz±25kHz B 10.67MHz±30kHz 10.675MHz±25kHz A 10.70MHz±30kHz 10.700MHz±25kHz C 10.73MHz±30kHz 10.725MHz±25kHz E 10.76MHz±30kHz 10.750MHz±25kHz Z Combination A,B,C,D,E M Combination A,B,C ■ Frequency Characteristics 5.50 1 5.50 1 5.00 2 5.00 2 4.50 3 4.50 3 4.00 4 4.00 4 3.50 5 3.50 5 3.00 6 3.00 6 2.50 2.50 7 7 10.500 10.600 10.700 Frequency (MHz) 10.800 10.900 Attenuation (dB) 0 10.500 10.600 10.700 Frequency (MHz) 10.800 10.900 G.D.T. (µsec.) SFELA10M7GA00-B0 6.00 G.D.T. (µsec.) Attenuation (dB) SFELA10M7HA00-B0 0 2.00 5.00 1 4.50 2 4.00 3 3.50 4 3.00 5 2.50 6 2.00 7 10.500 10.600 10.700 Frequency (MHz) 10.800 10.900 G.D.T. (µsec.) Attenuation (dB) SFELA10M7FA00-B0 0 1.50 ■ Frequency Characteristics (Spurious) SFELA10M7GA00-B0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFELA10M7HA00-B0 0 30 40 30 40 50 50 60 60 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 Continued on the following page. 12 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Continued from the preceding page. ■ Frequency Characteristics (Spurious) SFELA10M7FA00-B0 0 10 Attenuation (dB) 20 30 40 3 50 60 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 ■ Spurious Response SFELA10M7FA00-B0 0 10 Attenuation (dB) 20 30 40 50 60 70 0 20 40 60 80 100 Frequency (MHz) 13 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Ceramic Filters (CERAFILr) for FM Receivers CERAFILr Low-loss Type 7.0±2.0 SFELA10M7 series for FM-receivers are monolithic type ceramic filters which use the energy trapped thickness vibration-mode of the piezoelectric ceramic. EIAJ CODE ■ Features 1. Insertion loss is 1 to 1.5dB lower than conventional products. This types are useful for elevating the sensitivity of sets. 2. Small dispersion and stable characteristics. 3. Excellent shape factor of frequency response. 4. Good waveform symmetry. 5.0±1.0 1.38±0.2 1.7±0.1 0.5±0.1 3.0±1.0 SFELA_JAA0-B0 0.3±0.1 2.5±0.2 2.5±0.2 (3) (1) : Input (2) : Ground (3) : Output (in mm) (1) (2) 7.0±2.0 EIAJ CODE 7.0±2.0 MARKING 5.0±1.0 1.38±0.2 1.7±0.1 0.5±0.1 3.0±1.0 (3) MARKING MARKING 7.0±2.0 7.0±2.0 EIAJ CODE 0.5±0.1 5.0±1.0 1.38±0.2 1.7±0.1 5.0±1.0 1.38±0.2 1.7±0.1 0.5±0.1 (3) (2) SFELA_FAA0-B0 3.0±1.0 3.0±1.0 2.5±0.2 2.5±0.2 (1) : Input (2) : Ground (3) : Output 0.3±0.1 2.5±0.2 2.5±0.2 SFELA_GAA0-B0 (in mm) (1) (2) 7.0±2.0 EIAJ CODE (1) : Input (2) : Ground (3) : Output 7.0±2.0 SFELA_HAA0-B0 0.3±0.1 2.5±0.2 2.5±0.2 0.3±0.1 4 7.0±2.0 MARKING (in mm) (1) (3) (2) (1) : Input (2) : Ground (3) : Output (in mm) (1) Center Frequency (fo) (MHz) 3dB Bandwidth (kHz) Attenuation (kHz) Insertion Loss (dB) Spurious Attenuation (dB) SFELA10M7JAA0-B0 10.700 ±30kHz within150 ±40kHz 360 max. within4.5 ±2.0dB 35 min. SFELA10M7HAA0-B0 10.700 ±30kHz within180 ±40kHz 470 max. within3.5 ±1.5dB 35 min. SFELA10M7GAA0-B0 10.700 ±30kHz within230 ±50kHz 520 max. within3.0 ±2.0dB 35 min. SFELA10M7FAA0-B0 10.700 ±30kHz within280 ±50kHz 590 max. within2.5 ±2.0dB 30 min. Part Number Area of Attenuation : [within 20dB] Area of Spurious Attenuation : [within 9MHz to 12MHz] Center frequency(fo) defined by the center of 3dB bandwidth. 14 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 ■ Center Frequency Rank Code CODE 30kHz Step 25kHz Step D 10.64MHz±30kHz 10.650MHz±25kHz B 10.67MHz±30kHz 10.675MHz±25kHz A 10.70MHz±30kHz 10.700MHz±25kHz C 10.73MHz±30kHz 10.725MHz±25kHz E 10.76MHz±30kHz 10.750MHz±25kHz Z Combination A,B,C,D,E M Combination A,B,C ■ Frequency Characteristics 1 7.00 1 6.00 2 6.50 2 5.50 3 6.00 3 5.00 4 5.50 4 4.50 5 5.00 5 4.00 6 4.50 6 3.50 4.00 7 10.600 10.700 Frequency (MHz) 10.800 10.900 10.500 SFELA10M7GAA0-B0 10.600 10.700 Frequency (MHz) 10.800 10.900 3.00 SFELA10M7FAA0-B0 0 5.50 1 6.00 1 5.00 2 5.50 2 4.50 3 5.00 3 4.00 4 4.50 4 3.50 5 4.00 5 3.00 6 3.50 6 2.50 3.00 7 7 10.500 10.600 10.700 Frequency (MHz) 10.800 10.900 Attenuation (dB) 6.50 G.D.T. (µsec.) 0 10.500 10.600 10.700 Frequency (MHz) 10.800 10.900 G.D.T. (µsec.) 10.500 Attenuation (dB) 7.50 G.D.T. (µsec.) 6.50 0 7 Attenuation (dB) 4 SFELA10M7HAA0-B0 0 G.D.T. (µsec.) Attenuation (dB) SFELA10M7JAA0-B0 2.00 ■ Frequency Characteristics (Spurious) SFELA10M7HAA0-B0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFELA10M7JAA0-B0 0 30 40 30 40 50 50 60 60 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 Continued on the following page. 15 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Continued from the preceding page. ■ Frequency Characteristics (Spurious) 10 10 20 20 30 40 16 30 40 50 50 60 60 70 8.700 4 SFELA10M7FAA0-B0 0 Attenuation (dB) Attenuation (dB) SFELA10M7GAA0-B0 0 9.700 10.700 Frequency (MHz) 11.700 12.700 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Ceramic Filters (CERAFILr) for FM Receivers CERAFILr Low-profile Type SFELB10M7 series for FM-receivers are monolithic type ceramic filters which use the energy trapped thickness vibration-mode of the piezoelectric ceramic. 5.0±1.0 1.5±0.1 1.3±0.1 ■ Features 0.5±0.1 1. Installed height is 5 mm, making it well suited for compact, thin sets. 2. Environmental reliability is the same as those of the ceramic filter SFELA10M7 series. 3.0±1.0 SFELB10M7KA00-B0 0.3±0.1 2.5±0.2 2.5±0.2 (1) EIAJ CODE EIAJ CODE MARKING 0.5±0.1 5.0±1.0 1.5±0.1 1.3±0.1 5.0±1.0 1.5±0.1 1.3±0.1 0.5±0.1 (2) 3.0±1.0 SFELB10M7HA00-B0 in mm (3) (1) MARKING in mm (3) 7.5±2.0 EIAJ CODE 6.0 max. 7.5±2.0 (2) (1) : Input (2) : Ground (3) : Output MARKING 0.5±0.1 5.0±1.0 1.5±0.1 1.3±0.1 5.0±1.0 1.5±0.1 1.3±0.1 EIAJ CODE 6.0 max. (1) (1) : Input (2) : Ground (3) : Output 0.3±0.1 2.5±0.2 2.5±0.2 3.0±1.0 0.3±0.1 2.5±0.2 2.5±0.2 0.5±0.1 (1) (2) SFELB10M7FA00-B0 3.0±1.0 (1) : Input (2) : Ground (3) : Output 0.3±0.1 2.5±0.2 2.5±0.2 3.0±1.0 0.3±0.1 2.5±0.2 2.5±0.2 SFELB10M7GA00-B0 in mm (3) 6.0 max. MARKING (2) (1) : Input (2) : Ground (3) : Output 7.5±2.0 6.0 max. 7.5±2.0 SFELB10M7JA00-B0 EIAJ CODE MARKING 6.0 max. 7.5±2.0 in mm (3) (1) (2) (1) : Input (2) : Ground (3) : Output in mm (3) Center Frequency (fo) (MHz) 3dB Bandwidth (kHz) Attenuation (kHz) Insertion Loss (dB) Spurious Attenuation (dB) SFELB10M7KA00-B0 10.700 ±30kHz within110 ±30kHz 350 max. within7.0 ±2.0dB 30 min. SFELB10M7JA00-B0 10.700 ±30kHz within150 ±40kHz 360 max. within4.5 ±2.0dB 35 min. SFELB10M7HA00-B0 10.700 ±30kHz within180 ±40kHz 470 max. within3.5 ±2.0dB 35 min. SFELB10M7GA00-B0 10.700 ±30kHz within230 ±50kHz 570 max. within3.0 ±2.0dB 40 min. SFELB10M7FA00-B0 10.700 ±30kHz within280 ±50kHz 650 max. within3.0 ±2.0dB 30 min. Part Number Area of Attenuation : [within 20dB] Area of Spurious Attenuation : [within 9MHz to 12MHz] Center frequency(fo) defined by the center of 3dB bandwidth. 17 5 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 ■ Center Frequency Rank Code CODE 30kHz Step 25kHz Step D 10.64MHz±30kHz 10.650MHz±25kHz B 10.67MHz±30kHz 10.675MHz±25kHz A 10.70MHz±30kHz 10.700MHz±25kHz C 10.73MHz±30kHz 10.725MHz±25kHz E 10.76MHz±30kHz 10.750MHz±25kHz Z Combination A,B,C,D,E M Combination A,B,C ■ Frequency Characteristics 8.00 0 7.50 1 7.50 1 7.00 2 7.00 2 6.50 3 6.50 3 6.00 4 6.00 4 5.50 5 5.50 5 5.00 6 5.00 6 4.50 4.50 7 10.620 10.660 10.700 Frequency (MHz) 10.740 10.780 10.500 10.900 4.00 SFELB10M7GA00-B0 1 6.50 1 6.00 2 6.00 2 5.50 3 5.50 3 5.00 4 5.00 4 4.50 5 4.50 5 4.00 6 4.00 6 3.50 3.50 7 10.500 10.600 10.700 Frequency (MHz) 10.800 10.900 5.50 1 5.00 2 4.50 3 4.00 4 3.50 5 3.00 6 2.50 7 10.500 10.600 10.700 Frequency (MHz) 10.800 10.900 2.00 G.D.T. (µsec.) 0 Attenuation (dB) 7.00 SFELB10M7FA00-B0 Attenuation (dB) 10.800 0 7 18 10.700 Frequency (MHz) 0 G.D.T. (µsec.) Attenuation (dB) SFELB10M7HA00-B0 10.600 10.500 10.600 10.700 Frequency (MHz) 10.800 10.900 6.50 3.00 G.D.T. (µsec.) 7 Attenuation (dB) 0 G.D.T. (µsec.) Attenuation (dB) 5 SFELB10M7JA00-B0 G.D.T. (µsec.) SFELB10M7KA00-B0 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 ■ Frequency Characteristics (Spurious) SFELB10M7JA00-B0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFELB10M7KA00-B0 0 30 40 30 40 50 50 60 60 70 8.700 9.700 10.700 Frequency (MHz) 11.700 70 8.700 12.700 0 0 10 10 20 20 30 40 60 60 10.700 Frequency (MHz) 11.700 12.700 5 40 50 9.700 11.700 30 50 70 8.700 10.700 Frequency (MHz) SFELB10M7GA00-B0 Attenuation (dB) Attenuation (dB) SFELB10M7HA00-B0 9.700 12.700 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 SFELB10M7FA00-B0 0 10 Attenuation (dB) 20 30 40 50 60 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 19 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Ceramic Filters (CERAFILr) for FM Receivers CERAFILr Lower Spurious Response Type 7.5±2.0 SFELA10M7 series for FM-receivers are monolithic type ceramic filters which use the energy trapped thickness vibration-mode of the piezoelectric ceramic. EIAJ CODE 7.0±2.0 MARKING 0.5±0.1 2.5±0.2 2.5±0.2 3.0±1.0 SFELA10M7KAB0-B0 0.3±0.1 1. This type has lower spurious response compared to the standard filters. 2. This types are suitable for higher spurious suppression radio. 5.0±1.0 1.38±0.2 1.7±0.1 ■ Features (3) (1) (2) 7.5±2.0 7.5±2.0 MARKING MARKING EIAJ CODE 0.5±0.1 (3) (1) (2) (3) (1) (2) 7.5±2.0 7.5±2.0 MARKING MARKING EIAJ CODE EIAJ CODE 0.5±0.1 (3) (2) SFELA10M7FAB0-B0 0.3±0.1 2.5±0.2 2.5±0.2 3.0±1.0 0.3±0.1 2.5±0.2 2.5±0.2 (1) 3.0±1.0 0.5±0.1 5.0±1.0 1.38±0.2 1.7±0.1 5.0±1.0 1.38±0.2 1.7±0.1 SFELA10M7GAB0-B0 3.0±1.0 SFELA10M7HAB0-B0 0.3±0.1 3.0±1.0 2.5±0.2 2.5±0.2 7.0±2.0 SFELA10M7JAB0-B0 0.3±0.1 2.5±0.2 2.5±0.2 7.0±2.0 0.5±0.1 5.0±1.0 1.38±0.2 1.7±0.1 5.0±1.0 1.38±0.2 1.7±0.1 7.0±2.0 EIAJ CODE 7.0±2.0 6 (3) (2) (1) Center Frequency (fo) (MHz) 3dB Bandwidth (kHz) Attenuation (kHz) Insertion Loss (dB) Spurious Attenuation (dB) SFELA10M7KAB0-B0 10.700 ±30kHz within110 ±30kHz 350 max. 7.0 ±2.0dB 45 min. SFELA10M7JAB0-B0 10.700 ±30kHz within150 ±40kHz 380 max. 5.5 ±2.0dB 45 min. SFELA10M7HAB0-B0 10.700 ±30kHz within180 ±40kHz 520 max. 5.0 ±2.0dB 45 min. SFELA10M7GAB0-B0 10.700 ±30kHz within230 ±50kHz 570 max. 3.0 ±2.0dB 45 min. SFELA10M7FAB0-B0 10.700 ±30kHz within280 ±50kHz 650 max. 3.0 ±2.0dB 45 min. Part Number Area of Attenuation : [within 20dB] Area of Spurious Attenuation : [within 9MHz to 12MHz] Center frequency(fo) defined by the center of 3dB bandwidth. 20 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 ■ Center Frequency Rank Code CODE 30kHz Step 25kHz Step D 10.64MHz±30kHz 10.650MHz±25kHz B 10.67MHz±30kHz 10.675MHz±25kHz A 10.70MHz±30kHz 10.700MHz±25kHz C 10.73MHz±30kHz 10.725MHz±25kHz E 10.76MHz±30kHz 10.750MHz±25kHz Z Combination A,B,C,D,E M Combination A,B,C ■ Frequency Characteristics 8.00 0 7.00 1 7.50 1 6.50 2 7.00 2 6.00 3 6.50 3 5.50 4 6.00 4 5.00 5 5.50 5 4.50 6 5.00 6 4.00 4.50 7 10.620 10.660 10.700 Frequency (MHz) 10.740 10.780 10.500 10.700 Frequency (MHz) 10.800 10.900 3.50 SFELA10M7GAB0-B0 6.50 0 6.00 1 6.00 1 5.50 2 5.50 2 5.00 3 5.00 3 4.50 4 4.50 4 4.00 5 4.00 5 3.50 6 3.50 6 3.00 3.00 7 7 10.500 10.600 10.700 Frequency (MHz) 10.800 10.900 Attenuation (dB) 0 G.D.T. (µsec.) Attenuation (dB) SFELA10M7HAB0-B0 10.600 6 10.500 10.600 10.700 Frequency (MHz) 10.800 10.900 G.D.T. (µsec.) 7 Attenuation (dB) 0 G.D.T. (µsec.) SFELA10M7JAB0-B0 G.D.T. (µsec.) Attenuation (dB) SFELA10M7KAB0-B0 2.50 5.00 1 4.50 2 4.00 3 3.50 4 3.00 5 2.50 6 2.00 7 10.500 10.600 10.700 Frequency (MHz) 10.800 10.900 G.D.T. (µsec.) Attenuation (dB) SFELA10M7FAB0-B0 0 1.50 21 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 ■ Frequency Characteristics (Spurious) SFELA10M7JAB0-B0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFELA10M7KAB0-B0 0 30 40 30 40 50 50 60 60 70 8.700 9.700 10.700 Frequency (MHz) 11.700 70 12.700 8.700 SFELA10M7HAB0-B0 0 10 10 20 20 30 40 60 60 9.700 10.700 Frequency (MHz) 11.700 12.700 SFELA10M7FAB0-B0 0 10 Attenuation (dB) 20 30 40 50 60 70 22 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 40 50 8.700 11.700 30 50 70 10.700 Frequency (MHz) SFELA10M7GAB0-B0 0 Attenuation (dB) Attenuation (dB) 6 9.700 12.700 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Ceramic Filters (CERAFILr) for FM Receivers CERAFILr Wider Band-width Type 7.0±2.0 SFELA10M7 Series for FM-receivers are monolithic type ceramic filters which use the energy trapped thickness vibration-mode of the piezoelectric ceramic. EIAJ CODE ■ Features 7.0±2.0 MARKING 1. Realizes wider or narrower band characteristics not obtained by conventional ceramic filters. 2. Temperature characteristics are the best available, the same as those of Murata's conventional ceramic filters. Thus, even in the case of narrow band filters, the center frequency is stable even if temperature changes. 5.0±1.0 1.38±0.2 1.7±0.1 0.5±0.1 3.0±1.0 SFELA10M7EA00-B0 0.3±0.1 2.5±0.2 2.5±0.2 (3) (1) : Input (2) : Ground (3) : Output (in mm) (1) (2) 7.0±2.0 EIAJ CODE 7.0±2.0 MARKING 7 5.0±1.0 1.38±0.2 1.7±0.1 0.5±0.1 3.0±1.0 SFELA10M7DF00-B0 0.3±0.1 2.5±0.2 2.5±0.2 (3) Nominal Center Frequency (fo) Center Frequency(fn) (MHz) (MHz) Part Number (2) (1) : Input (2) : Ground (3) : Output (in mm) (1) 3dB Bandwidth (kHz) Attenuation (kHz) Insertion Loss (dB) Spurious Attenuation (dB) SFELA10M7EA00-B0 10.700 ±30kHz - within330 ±50kHz 680 max. within4.0 ±2.0dB 30 min. SFELA10M7DF00-B0 - 10.700 fn±175 min. 950 max. within3.0 ±2.0dB 20 min. Area of Attenuation : [within 20dB] Area of Spurious Attenuation : [within 9MHz to 12MHz] Center frequency(fo) defined by the center of 3dB bandwidth. (fn) means nominal center frequency. ■ Center Frequency Rank Code CODE 30kHz Step 25kHz Step D 10.64MHz±30kHz 10.650MHz±25kHz B 10.67MHz±30kHz 10.675MHz±25kHz A 10.70MHz±30kHz 10.700MHz±25kHz C 10.73MHz±30kHz 10.725MHz±25kHz E 10.76MHz±30kHz 10.750MHz±25kHz Z Combination A,B,C,D,E M Combination A,B,C 23 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 ■ Frequency Characteristics 4.00 1 4.00 1 3.50 2 3.50 2 3.00 3 3.00 3 2.50 4 2.50 4 2.00 5 2.00 5 1.50 6 1.50 6 1.00 1.00 7 7 10.300 10.500 10.700 Frequency (MHz) 10.900 11.100 Attenuation (dB) 0 10.300 10.500 10.700 Frequency (MHz) 10.900 11.100 0.50 ■ Frequency Characteristics (Spurious) 7 10 10 20 20 30 40 30 40 50 50 60 60 70 8.700 24 SFELA10M7DF00-B0 0 Attenuation (dB) Attenuation (dB) SFELA10M7EA00-B0 0 9.700 10.700 Frequency (MHz) 11.700 12.700 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 G.D.T. (µsec.) SFELA10M7DF00-B0 4.50 G.D.T. (µsec.) Attenuation (dB) SFELA10M7EA00-B0 0 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Ceramic Filters (CERAFILr) for FM Receivers CERAFILr Narrow Band Type 10.0±2.0 SFELA10M7LFTA/KAH0, SFVLA/SFKLA series realizes narrower band characteristics not obtained by conventional ceramic filters. Besides, low spurious and temperature characteristics is stable. This series suits for European car-audio or AM up conversion use that needs narrow band characteristics. EIAJ CODE 5.0±1.0 1.38±0.2 1.7±0.1 0.5±0.1 2.5±0.2 2.5±0.2 +1.5 3.5 –1.0 0.3±0.1 (3) 7.0 ±2.0 MARKING MARKING 7.0 ±2.0 7.0 ±2.0 EIAJ CODE in mm 5.0 ±1.0 1 .4±0 .1 0. 5±0 .1 (1) : Input (2) : Ground (3) : Output 3.0 ±1.0 SFVLA10M7MF00-B0 (3) (2) 2.5±0.2 2.5±0.2 0.3±0. 1 2.5±0.2 2.5±0.2 (1) : Input (2) : Ground (3) : Output 3.0 ±1.0 1. 4±0. 1 0. 5±0. 1 5.0 ±1.0 1 .65 ±0. 1 1. 65±0.1 0.3±0. 1 (1) (2) 7.0 ±2.0 SFKLA10M7NF00-B0 EI AJ CODE 10.0±2.0 MARKING SFVLA10M7LF00-B0 in mm (1 ) (3) (2) in mm (1 ) 7.0±2.0 7.0± 2.0 1.38± 0.2 1.7± 0.1 0.5±0.1 2.5±0.2 2.5±0.2 (3) (2) (1) (in mm) SFELA10M7KAH0-B0 (1) Input (2) Ground (3) Output 3.0±1.0 3.0± 1.0 0.3± 0.1 2.5 2.5 ± 0.2 ± 0.2 SFELA10M7LFTA01-B0 5.0±1.0 1.38±0.2 1.7±0.1 5.0±1.0 0.5± 0.1 (3) Part Number 7.0±2.0 EIAJ CODE 0.3±0.1 EIAJ CODE 7.0± 2.0 MARKING MARKING Nominal Center Frequency (fo) Center Frequency(fn) (MHz) (MHz) 3dB Bandwidth (kHz) Attenuation (kHz) (2) (1) : Input (2) : Ground (3) : Output Insertion Loss (dB) Spurious Attenuation (dB) SFKLA10M7NF00-B0 10.700 ±15kHz - 20 min. 95 max. 6.0 max. 24 min. SFVLA10M7MF00-B0 - 10.700 fn±13 min. 135 max. within5.5 ±2.5dB 30 min. SFVLA10M7LF00-B0 - 10.700 fn±25 min. 200 max. within5.5 ±2.5dB 30 min. SFELA10M7LFTA-B0 - 10.700 fn±25 min. 280 max. within7.0 ±2.0dB 30 min. SFELA10M7KAH0-B0 10.700 ±30kHz - within110 ±30kHz 350 max. within7.0 ±2.0dB 30 min. Area of Attenuation : [within 20dB] (in mm) (1) Area of Spurious Attenuation : [within 9MHz to 12MHz] 25 8 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 ■ Center Frequency Rank Code CODE 30kHz Step 25kHz Step D 10.64MHz±30kHz 10.650MHz±25kHz B 10.67MHz±30kHz 10.675MHz±25kHz A 10.70MHz±30kHz 10.700MHz±25kHz C 10.73MHz±30kHz 10.725MHz±25kHz E 10.76MHz±30kHz 10.750MHz±25kHz Z Combination A,B,C,D,E M Combination A,B,C ■ Frequency Characteristics SFVLA10M7MF00-B0 Attenuation (dB) Attenuation ( dB ) 0 19.0 1 18.0 2 17.0 3 16.0 4 15.0 5 14.0 6 13.0 G.D.T. (µsec.) SFKLA10M7NF00-B0 0 10 10.650 10.750 10.700 7 10.620 10.660 Frequency ( kHz ) 8 13.0 1 12.0 2 11.0 3 10.0 4 9.00 5 8.00 6 7.00 10.620 10.660 10.700 Frequency (MHz) 10.740 10.780 1 7.50 2 7.00 3 6.50 4 6.00 5 5.50 6 5.00 26 10.700 Frequency (MHz) 10.740 10.780 4.50 G.D.T. (µsec.) Attenuation (dB) 8.00 10.660 12.0 0 11.00 10.50 2 10.00 3 9.50 4 9.00 5 8.50 6 8.00 7 7.50 8 7.00 10.580 10.640 10.700 Frequency (MHz) SFELA10M7KAH0-B0 10.620 10.780 1 9 6.00 0 7 Attenuation (dB) 0 7 10.740 SFELA10M7LFTA01-B0 G.D.T. (µsec.) Attenuation (dB) SFVLA10M7LF00-B0 10.700 Frequency (MHz) 10.760 10.820 6.50 G.D.T. (µsec.) 10.600 10.800 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 ■ Frequency Characteristics (Spurious) SFKLA10M7NF00-B0 SFVLA10M7MF00-B0 0 0 10 10 20 Attenuation (dB) Attenuation ( dB ) 20 30 40 50 30 40 50 60 60 70 9.700 10.200 11.200 10.700 70 8.700 11.700 9.700 Frequency ( MHz ) SFVLA10M7LF00-B0 10.700 Frequency (MHz) 11.700 12.700 SFELA10M7LFTA01-B0 0 0 10 10 20 Attenuation (dB) Attenuation (dB) 20 30 40 50 30 40 50 60 70 60 70 8.700 80 9.700 10.700 Frequency (MHz) 11.700 12.700 90 9.700 10.200 10.700 Frequency (MHz) 11.200 11.700 8 SFELA10M7KAH0-B0 0 10 Attenuation (dB) 20 30 40 50 60 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 27 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Ceramic Filters (CERAFILr) for FM Receivers CERAFILr For FM -IF Tuners 9.0 max. SFELA10M7 series for FM-receivers are monolithic type ceramic filters which use the energy trapped thickness vibration-mode of the piezoelectric ceramic. EIAJ CODE 0.3 ±0.1 0.5 ±0. 1 4.0 max. SFELA10M7JAXE-B0 2.5±0.2 2.5±0.2 (3 ) (2) (1 ) 7.0±2.0 7.0±2.0 MARKING EIAJ CODE 5.0±1.0 1.38±0.2 1.7±0.1 0.5±0.1 2.5±0.2 2.5±0.2 (1) : Input (2) : Ground (3) : Output 3.0±1.0 SFELA10M7HA0G-B0 0.3±0.1 1. Little dispersion of amplitude characteristics and phase characteristics (G. D. T. characteristics). 2. The SFELA10M7G_X series has G. D. T characteristics and is useful for obtaining low distortion. SFELA10M7F_L series, in these ceramic filters, being in harmony with flatness of G. D. T. , roundness of the amplitude and selectivity characteristics, therefore, these ceramic filters are suitable to high-grade stereo tuners. Even if mismatching condition, they can keep little distortion because of low Qm of ceramic material. The SFELA10M7FA0G series is based on SFELA10M7FA00/GA00/HA00, and it obtains high selectivity with low loss. There is little dispersion of amplitude and G. D. T. characteristics, and low distortion rate can be obtained. 3. All products are inspected for symmetry and roundness of amplitude characteristics, and the flatness of G. D. T. characteristics. 5.0 ±1.0 1. 38 ±0.2 1. 7±0 .1 ■ Features (3) (in mm) (1) (2) 9.0 max. 10 .0 max. MARKING EIAJ CODE 5. 0±1 .0 1. 38 ±0.2 1. 7±0 .1 0. 3±0 .1 0.5 ±0. 1 4.0 max. 2.5±0.2 2.5±0.2 (3 ) (1 ) 7.0±2.0 MARKING MARKING 7.0±2.0 7.0±2.0 EIAJ CODE EIAJ CODE 0.5±0.1 3.0±1.0 2.5±0.2 2.5±0.2 (3) (2) (1) (1) : Input (2) : Ground (3) : Output SFELA10M7GALM-B0 0.3±0.1 2.5±0.2 2.5±0.2 3.0±1.0 0.5±0.1 5.0±1.0 1.38±0.2 1.7±0.1 5.0±1.0 1.38±0.2 1.7±0.1 SFELA10M7GA0G-B0 ( 2) 7.0±2.0 SFELA10M7HAXD-B0 0.3±0.1 9 10. 0 ma x. MARKING (in mm) (3) (2) (1) : Input (2) : Ground (3) : Output (in mm) (1) Continued on the following page. 28 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Continued from the preceding page. 7.0±2.0 9. 0 ma x. 0.5±0.1 2.5±0.2 2.5±0.2 (2 ) SFELA10M7FA0G-B0 3.0±1.0 4.0 max. (3) 0.3±0.1 2.5±0.2 2.5±0.2 (1) : Input (2) : Ground (3) : Output in mm (1 ) (3) 7.0±2.0 7.0±2.0 MARKING EIAJ CODE EIAJ CODE 5.0±1.0 0.5 ±0. 1 (1) : Input (2) : Ground (3) : Output SFELA10M7GAXX-B0 (in mm) (3) (1) (2) 2.5±0.2 2.5±0.2 4.0 max. 3.0±1.0 0.3±0.1 2.5±0.2 2.5±0.2 0.3 ±0.1 0.5±0.1 5.0 ±1.0 1. 38 ±0.2 1. 7±0 .1 1.38±0.2 1.7±0.1 (3) (in mm) (1) (2) 9.0 max. MARKING SFELA10M7GALP03-B0 (1) : Input (2) : Ground (3) : Output 11. 0 ma x. 0.3 ±0.1 0. 5±0.1 7.0±2.0 1.38±0.2 1.7±0.1 5.0 ±1.0 1. 38±0. 2 1. 7±0. 1 EIAJ CODE 5.0±1.0 EI AJ CODE SFELA10M7GAXA-B0 MARKING 11. 0 ma x. MARKING (2) (1 ) (1) : Input (2) : Ground (3) : Output in mm 7.0±2.0 7.0±2.0 MARKING EIAJ CODE 9 5.0±1.0 1.38±0.2 1.7±0.1 0.5±0.1 3.0±1.0 SFELA10M7FALL-B0 0.3±0.1 2.5±0.2 2.5±0.2 (3) Part Number (2) (1) : Input (2) : Ground (3) : Output (in mm) (1) Center Frequency (fo) 3dB Bandwidth Attenuation Insertion Loss Spurious Attenuation (MHz) (kHz) (kHz) (dB) (dB) GDT Bandwidth (kHz) SFELA10M7JAXE-B0 10.700 ±30kHz within150 ±30kHz 500 max. 14.0 max. 35 min. SFELA10M7HA0G-B0 10.700 ±30kHz within180 ±40kHz 520 max. 7.0 max. 40 min. fo±45 min.[within 0.5µsec.] SFELA10M7HAXD-B0 10.700 ±30kHz within180 ±30kHz 530 max. 14.0 max. 33 min. fo±60 min.[within 0.15µsec.] SFELA10M7GA0G-B0 10.700 ±30kHz within230 ±50kHz 600 max. 7.0 max. 40 min. fo±60 min.[within 0.5µsec.] SFELA10M7GALM-B0 10.700 ±30kHz within230 ±50kHz 600 max. within9.0 ±2.0dB 30 min. fo±60 min.[within 0.25µsec.] SFELA10M7GAXA-B0 10.700 ±30kHz within220 ±40kHz 610 max. 30 min. fo±80 min.[within 0.15µsec.] SFELA10M7FA0G-B0 10.700 ±30kHz within280 ±50kHz 650 max. within4.0 ±2.0dB 30 min. fo±85 min.[within 0.5µsec.] SFELA10M7GALP03-B0 10.700 ±30kHz within250 ±50kHz 650 max. 10.0 max. 30 min. fo±65 min.[within 0.25µsec.] SFELA10M7GAXX-B0 10.700 ±30kHz within250 ±40kHz 670 max. 12.0 max. 25 min. fo±110 min.[within 0.2µsec.] SFELA10M7FALL-B0 10.700 ±30kHz within280 ±50kHz 700 max. within7.0 ±2.0dB 25 min. fo±70 min.[within 0.25µsec.] 12.5 max. fo±50 min.[within 0.15µsec.] Area of Attenuation : [within 20dB] Area of Spurious Attenuation : [within 9MHz to 12MHz] Center frequency(fo) defined by the center of 3dB bandwidth. 29 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 ■ Center Frequency Rank Code CODE 30kHz Step 25kHz Step D 10.64MHz±30kHz 10.650MHz±25kHz B 10.67MHz±30kHz 10.675MHz±25kHz A 10.70MHz±30kHz 10.700MHz±25kHz C 10.73MHz±30kHz 10.725MHz±25kHz E 10.76MHz±30kHz 10.750MHz±25kHz Z Combination A,B,C,D,E M Combination A,B,C ■ Freq. Characteristics 5.00 0 6.00 1 4.75 1 5.50 2 4.50 2 5.00 3 4.25 3 4.50 4 4.00 4 4.00 5 3.75 5 3.50 6 3.50 6 3.00 3.25 7 10.600 10.700 Frequency (MHz) 10.800 10.900 10.500 SFELA10M7HAXD-B0 10.800 10.900 2.50 SFELA10M7GA0G-B0 0 6.00 1 4.25 1 5.50 2 4.00 2 5.00 3 3.75 3 4.50 4 3.50 4 4.00 5 3.25 5 3.50 6 3.00 6 3.00 2.75 7 0 4.00 0 3.75 1 3.75 1 3.50 2 3.50 2 3.25 3 3.25 3 3.00 4 3.00 4 2.75 5 2.75 5 2.50 6 2.50 6 2.25 2.25 7 10.500 10.600 10.700 Frequency (MHz) 10.800 10.900 Attenuation (dB) 4.50 7 10.500 7 10.500 10.600 10.700 Frequency (MHz) 10.800 10.600 10.700 Frequency (MHz) 10.800 10.900 2.50 10.900 Attenuation (dB) SFELA10M7GAXA-B0 G.D.T. (µsec.) SFELA10M7GALM-B0 Attenuation (dB) 10.700 Frequency (MHz) 0 G.D.T. (µsec.) Attenuation (dB) 9 10.600 G.D.T. (µsec.) 10.500 10.500 10.600 10.700 Frequency (MHz) 10.800 10.900 G.D.T. (µsec.) 7 Attenuation (dB) 0 G.D.T. (µsec.) SFELA10M7HA0G-B0 G.D.T. (µsec.) Attenuation (dB) SFELA10M7JAXE-B0 2.00 Continued on the following page. 30 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Continued from the preceding page. ■ Freq. Characteristics 3.75 1 4.50 1 3.50 2 4.00 2 3.25 3 3.50 3 3.00 4 3.00 4 2.75 5 2.50 5 2.50 6 2.00 6 2.25 1.50 7 0 3.25 0 3.25 1 3.00 1 3.00 2 2.75 2 2.75 3 2.50 3 2.50 4 2.25 4 2.25 5 2.00 5 2.00 6 1.75 6 1.75 1.50 7 10.500 10.600 10.700 Frequency (MHz) 10.800 10.900 10.500 7 10.500 10.600 10.700 Frequency (MHz) 10.800 10.700 Frequency (MHz) 10.800 10.900 2.00 10.900 Attenuation (dB) SFELA10M7FALL-B0 G.D.T. (µsec.) Attenuation (dB) SFELA10M7GAXX-B0 10.600 10.500 10.600 10.700 Frequency (MHz) 10.800 10.900 G.D.T. (µsec.) 7 Attenuation (dB) 0 G.D.T. (µsec.) SFELA10M7GALP03-B0 5.00 G.D.T. (µsec.) Attenuation (dB) SFELA10M7FA0G-B0 0 1.50 ■ Spurious Frequency 0 10 10 20 20 30 40 30 40 50 50 60 60 70 8.700 9.700 10.700 Frequency (MHz) 11.700 70 9.900 12.700 10 10 20 20 30 40 60 60 11.700 11.100 11.500 40 50 10.700 Frequency (MHz) 10.700 Frequency (MHz) 30 50 9.700 10.300 SFELA10M7GA0G-B0 0 Attenuation (dB) Attenuation (dB) SFELA10M7HAXD-B0 0 70 8.700 9 SFELA10M7HA0G-B0 0 Attenuation (dB) Attenuation (dB) SFELA10M7JAXE-B0 12.700 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 Continued on the following page. 31 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Continued from the preceding page. ■ Spurious Frequency SFELA10M7GAXA-B0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFELA10M7GALM-B0 0 30 40 30 40 50 50 60 60 70 8.700 9.700 10.700 Frequency (MHz) 11.700 70 8.700 12.700 0 10 10 20 20 30 40 60 60 9 10.700 Frequency (MHz) 11.700 70 8.700 12.700 10 10 20 20 30 40 32 11.700 12.700 40 50 60 60 10.700 Frequency (MHz) 10.700 Frequency (MHz) 30 50 9.700 9.700 SFELA10M7FALL-B0 0 Attenuation (dB) Attenuation (dB) SFELA10M7GAXX-B0 0 70 8.700 12.700 40 50 9.700 11.700 30 50 70 8.700 10.700 Frequency (MHz) SFELA10M7GALP03-B0 0 Attenuation (dB) Attenuation (dB) SFELA10M7FA0G-B0 9.700 11.700 12.700 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Ceramic Filters (CERAFILr) for FM Receivers CERAFILr Three-Elements Type SFTLA Series 10.0±1.0 SFTLA10M7 series for FM-receivers are monolithic type ceramic filters which use the energy trapped thickness vibration-mode of the piezoelectric ceramic. EIAJ CODE 6.0±1.0 MARKING 0.4±0.1 ■ Features 1.4±0.1 0.5±0.1 2.5±0.2 2.5±0.2 3.0±1.0 SFTLA10M7HA00-B0 0.3±0.1 (3) (2) (1) : Input (2) : Ground (3) : Output in mm (1) 10.0±1.0 MARKING EIAJ CODE 6.0±1.0 1. It has an excellent shape factor, and it is possible to obtain 1.5 times more excellent selectivity than SFELA10M7 series (by detuning +-300 or 400kHz). 2. Good performance of spurious suppression. 3. Having the same terminal pitch as the SFELA10M7 series, it easily replaces that series. 4. By replacing two SFELA10M7 series filters with one SFTLA10M7 filter,more compact sets can be made. 5. Well-suited for 1-chip ICs. 5.0±1.0 0.65±0.1 0.4±0.1 5.0±1.0 0.65±0.1 1.4±0.1 0.5±0.1 3.0±1.0 SFTLA10M7GA00-B0 0.3±0.1 2.5±0.2 2.5±0.2 (3) (2) (1) : Input (2) : Ground (3) : Output in mm (1) 10.0±1.0 EIAJ CODE 6.0±1.0 MARKING 10 0.4±0.1 5.0±1.0 0.65±0.1 1.4±0.1 0.5±0.1 3.0±1.0 SFTLA10M7FA00-B0 0.3±0.1 2.5±0.2 2.5±0.2 (3) (2) (1) : Input (2) : Ground (3) : Output in mm (1) Center Frequency (fo) (MHz) 3dB Bandwidth (kHz) Attenuation (kHz) Insertion Loss (dB) Spurious Attenuation (dB) SFTLA10M7HA00-B0 10.700 ±30kHz within180 ±40kHz 550 max. within5.5 ±2.5dB 50 min. SFTLA10M7GA00-B0 10.700 ±30kHz within230 ±40kHz 650 max. within6.0 ±2.0dB 50 min. SFTLA10M7FA00-B0 10.700 ±30kHz within280 ±50kHz 700 max. within6.0 ±2.0dB 50 min. Part Number Area of Attenuation : [within 40dB] Area of Spurious Attenuation : [within 9MHz to 12MHz] Center frequency(fo) defined by the center of 3dB bandwidth. 33 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 ■ Center Frequency Rank Code CODE 30kHz Step 25kHz Step D 10.64MHz±30kHz 10.650MHz±25kHz B 10.67MHz±30kHz 10.675MHz±25kHz A 10.70MHz±30kHz 10.700MHz±25kHz C 10.73MHz±30kHz 10.725MHz±25kHz E 10.76MHz±30kHz 10.750MHz±25kHz Z Combination A,B,C,D,E M Combination A,B,C ■ Frequency Characteristics 8.00 0 7.00 1 7.50 1 6.50 2 7.00 2 6.00 3 6.50 3 5.50 4 6.00 4 5.00 5 5.50 5 4.50 6 5.00 6 4.00 4.50 7 7 10.500 10.600 10.700 Frequency (MHz) 10.800 10.900 Attenuation (dB) 0 10.500 10.600 10.700 Frequency (MHz) 10.800 10.900 G.D.T. (µsec.) SFTLA10M7GA00-B0 G.D.T. (µsec.) Attenuation (dB) SFTLA10M7HA00-B0 3.50 10 6.00 1 5.50 2 5.00 3 4.50 4 4.00 5 3.50 6 3.00 7 10.500 10.600 10.700 Frequency (MHz) 10.800 10.900 G.D.T. (µsec.) Attenuation (dB) SFTLA10M7FA00-B0 0 2.50 ■ Frequency Characteristics (Spurious) SFTLA10M7GA00-B0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFTLA10M7HA00-B0 0 30 40 30 40 50 50 60 60 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 Continued on the following page. 34 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Continued from the preceding page. ■ Frequency Characteristics (Spurious) SFTLA10M7FA00-B0 0 10 Attenuation (dB) 20 30 40 50 60 70 8.700 9.700 10.700 Frequency (MHz) 11.700 12.700 10 35 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Lead Type CERAFILr Test Circuit and Characteristics Data ■ Test Circuit (1) R1 (2) (1) : Input (2) : Output (3) :Ground (3) RF Rg R2 Voltmeter C S.S.G Rg + R1 = R2 = 330Ω C = 10pF (Including stray capacitance and input capacitance of RF voltmeter.) W20 Center frequency SFELA10M7GA00-B0 Variation (kHz) W40 0 Y20 W2 W1 Y20 0 W20 W40 Temperature (˚C) W60 W80 Insertion loss Variation (dB) Y40 0 Y1 Y2 W40 W20 Y20 0 W20 W40 Temperature (˚C) W60 W80 Variation (kHz) Variation (kHz) Variation (dB) Variation (kHz) ■ Temperature Characteristics 3dB Band width 0 Y20 Y40 Y20 0 W20 W40 Temperature (˚C) W60 W80 W40 W20 Center frequency SFELA10M7HA00-B0 0 Y20 Y40 W2 W1 Y20 0 W20 W40 Temperature (˚C) W60 W80 0 W20 W40 Temperature (˚C) W60 W80 0 W20 W40 Temperature (˚C) W60 W80 Insertion loss 0 Y1 Y2 W40 W20 Y20 3dB Band width 0 Y20 Y40 Y20 ■ Matching Conditions 10 •When using ceramic filters, it is most important to match the input/output load to impedance 330 ohm (only SFELA10M7DF00-B0 is 470 ohm matching). Waveform symmetry is damaged when reactance is added to the input/output load. •Two ceramic filters directly connected can be used for high selelctivity. For reducing waveform variation, it is recommended to input a buffer AMP between ceramic filters. 36 •The SFELA10M7 and SFTLA10M7 series are of input/output symmetric structure so that in theory there is no input/output directionality. Actual circuits may use different input/output loading conditions (for example, mismatched impedance) or capacitance load. In such cases, the waveform will be a little changed by the direction of the input/output of the ceramic filters. Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Lead Type CERAFILr Characteristics Data and Notice ■ Loaded Resistance and Waveform (Rg+R1=330ohm) 1.2 1.0 0.8 0.6 0.4 0.2 0 10.5 10.6 10.7 10.8 10.9 Frequency (MHz) 1.2 1.0 0.8 0.6 0.4 0.2 0 10.5 10.6 10.7 10.8 10.9 Frequency (MHz) R2=1kΩ 0 1 2 3 4 5 6 7 1.2 1.0 0.8 0.6 0.4 0.2 0 10.5 10.6 10.7 10.8 10.9 Frequency (MHz) Group Delay Time (µsec.) Attenuation (dB) 0 1 2 3 4 5 6 7 Group Delay Time (µsec.) Attenuation (dB) R2=560Ω 0 1 2 3 4 5 6 7 R2=330Ω Attenuation (dB) 10.5 10.6 10.7 10.8 10.9 Frequency (MHz) Group Delay Time (µsec.) Attenuation (dB) 1.2 1.0 0.8 0.6 0.4 0.2 0 Group Delay Time (µsec.) SFELA10M7GA00-B0 R2=220Ω 0 1 2 3 4 5 6 7 ■ Loaded Capacitance and Waveform (Rg+R1=R2=330ohm) Attenuation (dB) C=56pF 0 1 2 3 4 5 6 7 1.2 1.0 0.8 0.6 0.4 0.2 0 10.5 10.6 10.7 10.8 10.9 Frequency (MHz) 1.2 1.0 0.8 0.6 0.4 0.2 0 10.5 10.6 10.7 10.8 10.9 Frequency (MHz) C=82pF 0 1 2 3 4 5 6 7 1.2 1.0 0.8 0.6 0.4 0.2 0 10.5 10.6 10.7 10.8 10.9 Frequency (MHz) Group Delay Time (µsec.) Attenuation (dB) 0 1 2 3 4 5 6 7 Group Delay Time (µsec.) 10.5 10.6 10.7 10.8 10.9 Frequency (MHz) C=33pF Attenuation (dB) 1.2 1.0 0.8 0.6 0.4 0.2 0 Group Delay Time (µsec.) Attenuation (dB) 0 1 2 3 4 5 6 7 Group Delay Time (µsec.) SFELA10M7GA00-B0 C=10pF ■ Notice (Soldering and Mounting) The component cannot be withstand washing. 10 ■ Notice (Handling) 1. Do not use this product with bend. The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. 2. The component may be damaged when an excess stress will be applied. 3. All kinds of re-flow soldering must not be applied on the component. 4. Do not clean or wash the component as it is not hermetically sealed. 5. Do not use strong acidity flux, more than 0.2wt% chlorine content, in flow soldering. 6. In case of covering discriminator with over coat, conditions such as material of resin, cure temperature, and so on should be evaluated well. 7. Accurate test circuit values are required to measure electrical characteristics. It may be a cause of mis-correlation if there is any deviation, especially stray capacitance, from the test circuit in the specification. 37 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Ceramic Filters (CERAFILr) for FM Receivers Discriminators Chip Type CDACV Series 1.5±0.3 3.4±0.5 ∗ 2.6±0.3 ∗∗ CDACV10M7 series forms a resonator on a piezoelectric ceramic substrate. In combination with ICs, this type obtains stable demodulation characteristics in wide bandwidths. ■ Features 0.9±0.3 0.9±0.3 1. Compact and excellent mechanical strength. 2. Can be combined with various ICs. The IC is determined by the last number in the part number. 3. Stable demodulation characteristics can be obtained without adjustment. 4. The MG type for wide bandwidths and the MC type for narrow bandwidths are available. 5. Stable temperature characteristics. 6. We recommend kits : ceramic discriminator CDACV10M7 series and "CERAFIL" SFECV10M7 of the same frequency rank. ∗ : EIAJ Monthly Code ∗∗ : Rank in mm Center Frequency (fo) Recovered Audio 3dB BW Recovered Audio Output Distortion (MHz) (kHz) (mV) (%) Part Number IC Detection Method CDACV10M7GA001-R0 10.700 ±30kHz fo±150 min. 55 min. 1.0 max. CX20029 Quadrature CDACV10M7GA016-R0 10.700 ±30kHz 300 min. within60 to 90mV 0.9 max. TA8122F Quadrature CDACV10M7GA046-R0 10.700 ±30kHz 330 min. 280 min. 1.5 max. LA1832 Quadrature CDACV10M7GA069-R0 10.700 ±30kHz 330 min. 80 min. 1.0 max. CXA1538N Quadrature CDACV10M7CA001-R0 10.700 ±30kHz fo±150 min. 55 min. 1.0 max. CX20091 Quadrature ■ Center Frequency Rank Code 11 CODE 30kHz Step 25kHz Step D 10.64MHz±30kHz 10.650MHz±25kHz B 10.67MHz±30kHz 10.675MHz±25kHz A 10.70MHz±30kHz 10.700MHz±25kHz C 10.73MHz±30kHz 10.725MHz±25kHz E 10.76MHz±30kHz 10.750MHz±25kHz Z Combination A,B,C,D,E M Combination A,B,C ■ Standard Land Pattern Dimensions 1.5 2.6 1.5 1.4 38 1.5 1.4 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 ■ CDACV10M7GA001-R0 Test Circuit Frequency Characteristics 100 1000 AFC REF 33 1µ 32 39 AF OUTPUT – AF Output 28 CDALA10M7GA001 10 100 100k Fg=50 9 S.S.G. + CX20029 Vcc=+3.0V Unit R:Ω C:F Distortion (%) 0.01µ Recovered AF Output Voltage (mV) 5 280 1 10 Distortion 0.1 1 Input signal conditions Input Level Mod. Freq. Freq.Dev. 10.4 10.5 10.6 10.7 10.8 Frequency (MHz) 10.9 100dBµ 1000Hz ±22.5kHz 11.0 ■ CDACV10M7GA016-R0 Test Circuit Frequency Characteristics 2.5µ 0.1µ 100 4 5 6 7 8 9 10 11 12 0.022µ 3 + 22µ 2 Recovered AF Output Voltage (mV) TA8122F (TOSHIBA) CDACV10M7GA016 SFELA10M7DF00 Unit R:Ω C:F 270 0.022µ IF in 10 AF Output 1 10 Distortion Distortion (%) 24k 0.033µ + 24 23 22 21 20 19 18 17 16 15 14 13 1 100 1000 DC Out AF Out 330p 1k VCC +3V 0.1 1 Input signal conditions Input Level Mod. Freq. Freq.Dev. 10.4 10.5 10.6 10.7 10.8 Frequency (MHz) 10.9 80dBµ 1000Hz ±22.5kHz 11.0 11 ■ CDACV10M7GA046-R0 Test Circuit Frequency Characteristics AF OUT 100 1000 CSBLA456KE2ZF15 0.01µ + 1µ + 3.3µ 24 23 22 1 2 3 21 20 LA1832 6.8k 4 5 300 18 17 16 15 7 8 9 10 CDALA10M7GA046 2.2µ 75 10µ + 1µ 14 13 11 12 3k 1µ 0.047µ + REG Vcc (5V) 10 100 (SANYO) 6 270 0.047µ IF-IN 19 AF Output 0.01µ + 100µ Unit R:Ω C:F Distortion 1 10 Distortion (%) AFC 1200p + 22µ 0.047µ Recovered AF Output Voltage (mV) 5.6k 0.1 1 Input signal conditions Input Level Mod. Freq. Freq.Dev. 10.4 10.5 10.6 10.7 10.8 Frequency (MHz) 10.9 112dBµ 1000Hz ±75kHz 11.0 Continued on the following page. 39 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Continued from the preceding page. ■ CDACV10M7GA069-R0 Test Circuit Frequency Characteristics CDACV10M7GZ069-B0 VCC (3V) Reg 3.3µ 2.2k 0.01µ + 100 10µ 100 1000 10µ + + 28 27 26 25 24 23 22 21 20 19 18 17 16 10 11 12 13 14 15 3 4 5 6 7 8 100 µ 0.01µ + + 9 + 1µ 1µ 2 33µ 1 + 4.7µ CXA1538N 0.01µ 0.01µ + AF OUT 0.022µ VCC (3V) 3.3k 0.022µ AFC IF IN Unit R:Ω C:F 3.3k 10 100 10 Distortion (%) 29 Recovered AF Output Voltage (mV) AF Output 30 1 Distortion 0.1 1 Input signal conditions 10.4 10.5 10.6 10.7 10.8 10.9 11.0 Frequency (MHz) Input Level 100dBµ Mod.Freq. 1000Hz Freq.Dev. ±75kHz ■ CDACV10M7CA001-R0 Test Circuit 25 24 23 22 20 19 18 17 16 15 CX20091 (SONY) 2 3 4 5 6 4.7µ 100 + 7 8 9 10 11 12 13 14 1000p 1 CDACV10M7CZ001-B0 REG OUT 10 100 10 0.01µ 0.01µ 280 21 1000 Unit R:Ω C:F AF Output 10 1 Distortion (%) 26 + Recovered AF Output Voltage (mV) 27 Frequency Characteristics INPUT S.S.G.(Rg=50) + + 28 AFC OUT 10µ 4.7µ 0.022µ 100µ + AF OUT 10µ Vcc 3V Distortion 0.1 1 Input signal conditions 10.4 10.5 10.6 10.7 10.8 Frequency (MHz) 11 40 10.9 11.0 Input Level 100dBµ Mod.Freq. 1000Hz Freq.Dev. ±22.5kHz Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Chip Type Discriminators CDACV Series Notice ■ Notice (soldering and mounting) 1. Standard Reflow Soldering Condition (1) Reflow 5sec. 240 Temperature (˚C) 230 Gradual Cooling 150 60 30 Time (sec.) (2) Soldering Iron Lead terminal is directly contacted with the tip of soldering iron of 280±5˚C for 3.0±0.5 seconds. 2. Wash The component cannot be withstand washing. ■ Notice (handling) 1. The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. 2. Design layout of components on the PC board to minimize the stress imposed on the warp or flexure of the board. 3. After installing chips, if solder is excessively applied to the circuit board, mechanical stress will cause destruction resistance characteristics to lower. To prevent this, be extremely careful in determining shape and dimension before designing the circuit board diagram. 4. When the positioning claws and pick up nozzle are worn, the load is applied to the chip while positioning is concentrated to one positioning accuracy, etc. Careful checking and maintenance are necessary to prevent unexpected trouble. 5. When correcting chips with a soldering iron, the tip of the soldering iron should not directly touch the chip component. Depending on the soldering conditions, the effective area of terminations may be reduced. the use of solder containing Ag should be done to prevent the electrode erosion. 6. Do not clean or wash the component as it is not hermetically sealed. 7. In case of covering discriminator with over coat, conditions such as material of resin, cure temperature, and so on should be evaluated well. 8. Accurate test circuit values are required to measure electrical characteristics. It may be a cause of mis-correlation if there is any deviation, especially stray capacitance, from the test circuit in the specification. [Component direction] Put the component lateral to the direction in which stress acts. [Component layout close to board] Perforation A B Slit C Susceptibility to stress is in the order of : A>C>B 11 41 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Ceramic Filters (CERAFILr) for FM Receivers 0.3±0.2 Discriminators Chip Low-profile Type CDSCA Series 0.2±0.2 1.4max 1.2max 0.4(ref.) 1. Compact and high reliability and recommended for automotive applications. 2. Can be combined with various ICs. The IC is determined by the last number in the part number. 3. Stable demoduration characteristics can be obtained without adjustment. 4. Stable temperature characteristics. 5. Recommended for Pb free soldering. Part Number 10.700 (fn) fn±80 min. ■ Standard Land Pattern Dimensions 2.6 3.0 2.0 0.8±0.1 1.5±0.1 (fn) means nominal center frequency. 1.0 0.4(ref.) 0.8±0.1 Center Frequency (fo) Recovered Audio 3dB BW Recovered Audio Output Distortion (MHz) (kHz) (mV) (%) CDSCA10M7GF107-R0 1.0 (in mm) 42 0.4±0.05 4.1max ■ Features 12 4.5±0.1 2.0±0.1 CDSCA10M7 series forms a resonator on a piezo electric ceramic sabstrate. In combination with ICs, this type obtains stable demoduration characteristics in wide bandwidth. 52 min. 3.0 max. 1.5±0.1 (in mm) IC Detection Method TA31272F Quadrature Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. ■ Test Circuit P61E7.pdf 01.10.17 ■ Frequency Characteristics Vcc (5.0V) AF OUT 0.01µF 100 1000 0.01µF 5 0.01µF S.S.G. 6 7 8 9 10 11 12 1000pF 4 0.01µF 3 0.01µF 2 0.1µF X R C 0.1µF X: CDSCA10M7GF107-B0 R: 1.2 [kohm] C: open 100 10 AF Output Distortion 1 10 Distortion (%) TA31272F 1 Recovered AF Output Voltage (mV) 24 23 22 21 20 19 18 17 16 15 14 13 Input signal conditions 0.1 1 Input Level Mod. Freq. Freq.Dev. 10.4 10.5 10.6 10.7 10.8 Frequency (MHz) 10.9 100dBµ 1000Hz ±40kHz 11.0 12 43 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Chip Type Discriminators CDSCA Series Notice ■ Notice (Soldering and Mounting) 1. Standard Reflow Soldering Condition (1) Reflow 5 sec 260 Temperature (°C) 240 Gradual Cooling 150 60 60 Time (sec.) (2) Soldering Iron Lead terminal is directly contacted with the tip of soldering iron of +280±5°C for 3.0 seconds±0.5 seconds. 2. Wash The component cannot be withstand washing. ■ Notice (Handling) 12 1. The component mounted on the PCB may be damaged if excess mechanical stress is applied. 2. Layout the components on the PCB to minimize the stress imposed by the warp or flexure of the board. 3. After installing components, if solder is excessively applied to the circuit board, mechanical stress will cause destruction resistance characteristics to be lower. To prevent this, be extremely careful in determining shape and dimension before designing the circuit board diagram. 4. When the positioning claw or pick up nozzle are worn, the excess load is applied to the components while positioning or placing are performed. Careful checking and maintenance are necessary to prevent unexpected trouble. 5. When correcting component's position with a soldering iron, the tip of the soldering iron should not directly touch the chip component. Depending on the soldering conditions, the effective area of terminations may be reduced. The use of solder containing Ag should be considerd to prevent the electrode erosion. 6. Do not clean or wash the component as it is not hermetically sealed. 7. In case of overcoating the part, coating conditions such as material, curing temperature, and so on must be evaluated deeply. 8. Accurate test circuit values are required to measure electrical characteristics. It may be a cause of mis-correlation if there is any deviation, especially stray capacitance, from the test circuit in the specification. 44 [Component direction] Put the component laterally to the direction in which stress acts. [Component layout close to board] Perforation B A Slit C Susceptibility to stress is in the order of : A>C>B Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Ceramic Filters (CERAFILr) for FM Receivers Discriminators CDALA Series 8.0±1.0 Freq. Rank (Color Dot) EIAJ CODE MARKING 5.0±1.0 CDALA10M7 series forms a resonator on a piezoelectric ceramic substrate. In combination with ICs, this type obtains stable demodulation characteristics in wide bandwidths. 5.0±1.0 0.4±0.1 0.65±0.1 ■ Features 3.0±1.0 5.0±0.2 CDALA10M7G_ Series (in mm) 8.0±1.0 Freq. Rank (Color Dot) EIAJ CODE MARKING 5.0±1.0 1. Compact and excellent mechanical strength. 2. Can be combined with various ICs. The IC is determined by the last number in the part number. 3. Stable demodulation characteristics can be obtained without adjustment. 4. The MG type for wide bandwidths and the MC type for narrow bandwidths are available. 5. Stable temperature characteristics. 6. We recommend combination : ceramic discriminator CDALA10M7 series and "CERAFIL" SFELA10M7 of the same frequency rank. 0.3±0.1 0.5±0.1 5.0±1.0 0.4±0.1 0.65±0.1 0.3±0.1 0.5±0.1 3.0±1.0 5.0±0.2 CDALA10M7C_ Series (in mm) Center Frequency (fo) Recovered Audio 3dB BW Recovered Audio Output Distortion (MHz) (kHz) (mV) (%) Part Number IC Detection Method CDALA10M7GA001-B0 10.700 ±30kHz 345 min. 25 min. 0.6 max. CX20029 Quadrature CDALA10M7GA016-B0 10.700 ±30kHz 300 min. within60 to 90mV 0.9 max. TA8122F Quadrature CDALA10M7GA018-B0 10.700 ±30kHz 300 min. 60 min. 0.9 max. TA8132N Quadrature CDALA10M7GA046-B0 10.700 ±30kHz 330 min. 280 min. 1.0 max. LA1832 Quadrature CDALA10M7GA048-B0 10.700 ±30kHz 400 min. 700 min. 1.0 max. LA1835 Quadrature CDALA10M7GA092-B0 10.700 ±30kHz 300 min. 60 min. 1.0 max. TA2132P Quadrature CDALA10M7CA001-B0 10.700 ±30kHz 242 min. 35 min. - CX20091 Quadrature CDALA10M7CA005A-B0 10.700 ±30kHz 100 min. 600 min. 6.0 max. LA7770 Quadrature CDALA10M7CA040-B0 10.700 ±30kHz 130 min. 40 min. 0.7 max. TEA5710 Quadrature ■ Center Frequency Rank Code CODE 30kHz Step 25kHz Step D 10.64MHz±30kHz 10.650MHz±25kHz B 10.67MHz±30kHz 10.675MHz±25kHz A 10.70MHz±30kHz 10.700MHz±25kHz C 10.73MHz±30kHz 10.725MHz±25kHz E 10.76MHz±30kHz 10.750MHz±25kHz Z Combination A,B,C,D,E M Combination A,B,C 13 45 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 ■ CDALA10M7GA001-B0 Test Circuit Frequency Characteristics 500 AFC REF – 10 AF OUTPUT 28 CDALA10M7GA001 S.S.G. + 100k Fg=50 CX20029 9 100 1µ 32 39 Vcc=+3.0V Unit R:Ω C:F AF Output 10 1 Distortion (%) 33 0.01µ Recovered AF Output Voltage (mV) 5 280 Distortion 1 0.1 Input signal conditions Input Level Mod. Freq. Freq.Dev. 10.4 10.5 10.6 10.7 10.8 Frequency (MHz) 10.9 110dBµ 400Hz ±22.5kHz 11.0 ■ CDALA10M7GA016-B0 Test Circuit Frequency Characteristics 500 DC Out AF Out 2.5µ 330p 1k 100 10 TA8122F (TOSHIBA) 3 4 5 6 + 7 8 9 10 11 12 0.022µ 2 22µ 1 CDACV10M7GA016 SFELA10M7DF00 Unit R:Ω C:F 270 0.022µ IF in Recovered AF Output Voltage (mV) 24 23 22 21 20 19 18 17 16 15 14 13 AF Output 10 1 Distortion 1 Distortion (%) 24k 0.033µ + 0.1µ VCC +3V 0.1 Input signal conditions Input Level Mod. Freq. Freq.Dev. 10.4 10.5 10.6 10.7 10.8 Frequency (MHz) 10.9 80dBµ 1000Hz ±22.5kHz 11.0 ■ CDALA10M7GA018-B0 Test Circuit CDALA10M7GA018 1k 1000 0.022µ 330p TA8132N (TOSHIBA) 2 3 4 5 6 7 8 9 10 11 12 22µ + 0.022µ Unit R:Ω C:F Recovered AF Output Voltage ( mV ) 0.033µ 24 23 22 21 20 19 18 17 16 15 14 13 1 100 + 0.1µ 270 SFELA10M7DF00 13 Frequency Characteristics DC out AF out 2.2µ 10 AF Output 100 10 1 Distortion Distortion (%) Vcc 3V 24k 1F in Vcc 3V 1 0.1 Input signal conditions Input Level 80 dBµ Mod. Freq. 1000 Hz Freq. Dev. ±22.5 kHz 10.4 10.5 10.6 10.7 10.8 10.9 Frequency ( MHz ) 11.0 Continued on the following page. 46 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Continued from the preceding page. ■ CDALA10M7GA046-B0 Test Circuit Frequency Characteristics AF OUT CSBLA456KE2ZF15 0.01µ 24 23 22 21 20 19 18 LA1832 6.8k 1 2 3 4 5 17 16 15 14 6 7 8 9 10 11 12 270 3k 2.2µ CDALA10M7GA046 75 IF-IN + 10µ 1µ 13 (SANYO) 300 0.047µ AF Output 0.01µ + 1µ 0.047µ + REG 100µ Unit R:Ω C:F 10 100 Distortion 10 1 1 0.1 Distortion ( % ) 1200p + 22µ 0.047µ + 1µ + 3.3µ Recovered AF Output Voltage ( mV ) 5.6k AFC 100 1000 Vcc (5V) Input signal conditions Input Level 112 dBµ Mod. Freq. 1000 Hz Freq. Dev. ±75 kHz 10.4 10.5 10.6 10.7 10.8 Frequency ( MHz ) 10.9 11.0 ■ CDALA10M7GA048-B0 Test Circuit Frequency Characteristics Vt 500 CSBLA456KE2ZF15 33n 3.3µ + L. P. F. 30 29 28 27 26 1 2 3 4 5 25 24 23 22 21 AF Output Rch Lch 10µ 10µ + + + 1µ 15k 5k 20 19 18 17 16 11 12 13 14 15 100 LA1835 (SANYO) + 0.047µ 0.047µ 75 6 7 8 9 1µ 1k 1k IF-IN 47n 10 10µ 510 300 20k 3k + 10µ + + 0.47µ Unit R:Ω C:F CDALA10M7GA048 10µ VCC(7V) REG. 10 10 1 Distortion 1 Distortion (%) AFC 47n L. P. F. 33n Recovered AF Output Voltage (mV) 1500p 0.1 Input signal conditions Input Level Mod. Freq. Freq.Dev. 10.4 10.5 10.6 10.7 10.8 Frequency (MHz) 10.9 112dBµ 1000Hz ±75kHz 11.0 ■ CDALA10M7GA092-B0 Test Circuit Frequency Characteristics DC OUT 2.2µ 2 13 12 11 10 9 7 8 Vcc(3.0V) 4.7µ TA2132P(TOSHIBA) 4 5 6 270 0.01µ + 4.7µ 3 IF-IN 10 100 Unit R:Ω C:F 13 AF Output 10 1 Distortion Distortion (%) 1 14 + Recovered AF Output Voltage (mV) 15 CDALA10M7GZ092-B0 0.033µ 20k 330p 16 500 AF OUT + 0.1 1 Input signal conditions 10.4 10.5 10.6 10.7 10.8 Frequency (MHz) 10.9 11.0 Input Level 80dBµ Mod.Freq. 1000Hz Freq.Dev. ±22.5kHz Continued on the following page. 47 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Continued from the preceding page. ■ CDALA10M7CA001-B0 Test Circuit VCC 5V AF Output Frequency Characteristics AFC 1000 IF in 100 + CX20090 100 4 + 5 6 (SONY) 7 8 9 10 11 12 13 14 1k 3 10µ 2 CDALA10M7CA001 1 18 17 16 15 Unit R:Ω C:F Ref. 100 10 AF Output Distortion ( % ) + 28 27 26 25 24 23 22 21 20 19 Recovered AF Output Voltage ( mV ) + + 0.01µ + 10µ 4.7µ 0.1µ 10µ 100µ 33µ 0.01µ 1 10 Distortion 0.1 1 Input signal conditions Input Level 110 dBµ Mod. Freq. 400 Hz Freq. Dev. ±22.5 kHz 10.4 10.5 10.6 10.7 10.8 Frequency ( MHz ) 10.9 11.0 ■ CDALA10M7CA005A-B0 Test Circuit Frequency Characteristics 1 2 18 17 16 15 14 13 12 11 9 10 IC : LA7770 (SANYO) 3 4 5 6 7 8 5p 0.01µ 0.01µ 0.01µ + - 0.01µ 33µ 1000p Vcc=12V 0.022p 50 IF IN Unit R:Ω C:F Recovered AF Output Voltage ( mV ) 19 AF Output 100 1000 Distortion 100 10 Distortion ( % ) 470p 0.1µ 2k 220p 20 500 Demod.OUT 10k CDALA10M7CA005A 2k 10k 20k 10k 5.6k 0.01µ 0.1µ DC Bias +5.2V DC Bias +5V DATA OUT 470p 5000 1 10 Input signal conditions Input Level 100 dBµ Mod. Freq. 1000 Hz Freq. Dev. ±75 kHz 10.6 10.7 10.8 Frequency ( MHz ) ■ CDALA10M7CA040-B0 Test Circuit Frequency Characteristics VCC (3V) + + 0.01µ + 1µ DC-OUT 13 24 23 22 21 20 19 18 TEA5710 1 2 3 4 5 0.22µ 6 17 16 15 14 13 10 11 12 (PHILIPS) 7 8 9 0.01µ 280 0.22µ 50 S.S.G. Unit R:Ω C:F 100 10 AF Output Distortion 10 1 1 0.1 Distortion (%) + 100 AF-OUT 100µ 10µ Recovered AF Output Voltage ( mV ) 0.01µ 100µ 1000 Input signal conditions Input Level 100 dBµ Mod. Freq. 1000 Hz Freq. Dev. ±22.5 kHz 10.4 10.5 10.6 10.7 10.8 Frequency ( MHz ) 48 10.9 11.0 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Lead Type Discriminators Notice ■ Notice (Soldering and Mounting) The component cannot be withstand washing. ■ Notice (Handling) 1. Do not use this product with bend. The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. 2. The component may be damaged when an excess stress will be applied. 3. All kinds of re-flow soldering must not be applied on the component. 4. Do not clean or wash the component as it is not hermetically sealed. 5. Do not use strong acidity flux, more than 0.2wt% chlorine content, in flow soldering. 6. In case of covering discriminator with over coat, conditions such as material of resin, cure temperature, and so on should be evaluated well. 7. Accurate test circuit values are required to measure electrical characteristics. It may be a cause of mis-correlation if there is any deviation, especially stray capacitance, from the test circuit in the specification. 13 49 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Packaging ■ Minimum Quantity Ammo Pack Bulk SFELA 1,500 500 SFELB 1,500 500 SFVLA 1,000 500 SFKLA 1,500 500 Part Number Taping ø180mm SFECV 2,000 SFECS 2,000 SFTLA 500 CDACV / CDSCA 2,000 CDALA 500 1,500 ■ Chip Type CERAFILr ■ Small Chip Type CERAFILr 40T0.15 10 pitch accumulated 4.0T0.1 5.5T0.05 ∗∗ 3.0T0.1 Peeling strength 0.1~0.7N Part number marked side is always facing upside. The feeding holes side of cavity tape is always input terminal. 1.9T0.1 10 max. W0.1 3 max. Cover Tape 1.7 Y0.05 0.3T0.05 Chip Filter 4.0T0.1 Peeling strengh (0.1Y0.7N) 3.35T0.1 4.0T0.1 Part number marked side is always facing upside. User Direction of Feed 10˚ 12.0±0.2 1.75±0.1 5.5±0.05 +0.1 -0 Ø1.5 2.2±0.1 The cover film peel strength force 0.1~0.7N Cover Film Part Number marked side is always facing upside 3˚max. Direction of Feed (1.85max.) 1.9T0.1 . W0.1 ax 0.3T0.05 10 max. 3m 4.0±0.1 1.7 Y0.05 Cover Tape 4.7±0.1 (9.5) 3.0T0.1 4.0T0.1 Peeling strengh (0.1Y0.7N) +0.1 -0 Ø1.5 2.0±0.05 12.0T0.2 5.5T0.5 4.0T0.1 4.0±0.1 1.25±0.05 1.75T0.1 CDSCA Series 0.3T0.01 3.8T0.1 2.0T0.05 3.45 ■ Chip Type Low-Profile Type Discriminator CDACV Series W0.1 3˚max. 10˚ max. Cover film User direction of feed · Part Number marked side is always facing upside. · The feeding holes side of cavity tape is always input terminal. (in mm) User Direction of Feed ■ Chip Type Discriminator φ1.5 Y0.0 12.0T0.2 ∗ ∗∗ 4.3 ∗ ∗∗ 0.05 ∗ ∗∗ Chip Filter 12.0 +0.08 -0.2 ∗ ∗∗ 7.3T0.01 ∗ 5.5T0.05 φ1.55T0.05 2.0T0.05 2.02T0.1 4.0T0.1 0.3T0.05 2.0T0.05 0.3±0.05 W0.1 φ1.5 Y0.0 SFECS Series 1.75T0.1 SFECV Series (in mm) Continued on the following page. 13 50 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Packaging Continued from the preceding page. ■ Lead Type CERAFILr SF_LA Series P2 ∆h ∆h P H0 W1 W0 W L2 L1 W2 ∆S1 F1 F1 P1 D0 F t P0 Code Dimensions Lead Length under the Hold Down Tape Item L1 3.0 min. Tolerance Length of Cat off L2 2.0 max. Pitch of Components P 12.7 ±0.5 Pitch of Sprocket Hole (1) P0 12.7 ±0.2 To distinguish the direction Length from Hole Center to Lead P1 3.85 ±0.5 Length from Hole Center to Component Center P2 6.35 Pitch of the Terminal (1) F 5.0 Pitch of the Terminal (2) F1 2.5 ±0.5 +0.5 –0.2 ±0.2 Slant to the Forward or Backward ∆h 0 ±1.0 Slant to the Left or Right ∆S1 0 ±1.0 Width of Carrier Tape W 18.0 ±0.5 Width of Hold Down Tape W0 6.0 min. Position of Sprocket Hole W1 9.0 Gap of Hold Down Tape and Carrier Tape W2 0 ±0.5 +0.5 –0 Distance Between the Center of Sprocket Hole and Lead Stpper H0 18.0 ±0.5 Diameter of Sprocket Hole D0 ø4.0 ±0.2 t 0.6 ±0.2 P020 254.0 ±1.5 Total Tape Thickness Pitch of Sprocket Hole (2) Remarks Must not protrude to the carrier tape The pitch of 20 sprocket holes (in mm) Continued on the following page. 13 51 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Packaging Continued from the preceding page. ■ Lead Type Discriminator CDALA Series P2 ∆h ∆h P H0 W1 W0 W L1 W2 ∆S1 D0 P1 F t P0 Item Lead length under the hole down tape Code Dimensions Tolerance L1 3.0 min. ——— Pitch of component P 12.7 ±0.5 Pitch of sprocket hole (1) P0 12.7 ±0.2 Length from hole center to lead P1 3.85 ±0.5 Length from hole center to component center P2 6.35 ±0.5 Lead spacing F 5.0 +0.5 -0.2 Slant to the forward or backward ∆h 0 ±1.0 Slant to the left or right ∆S1 0 ±1.0 W 18.0 ±0.5 Width of hold down tape W0 6.0 min. ——— Position of sprocket hole W1 9.0 ±0.5 Gap of hold down tape and Carrier tape W2 0 +0.5 -0.0 Distance between the center of sprocket hole and lead stopper H0 18.0 ±0.5 Diameter of sprocket hole D0 ø4.0 ±0.2 t 0.6 ±0.2 Po20 254.0 ±1.5 Width of carrier tape Total tape thickness Pitch of sprocket hole (2) Remarks Hold down tape doesn't exceed the carrier tape The pitch of 20 sprocket holes (in mm) 13 52 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Test Circuit of Ceramic Discriminator IC Manufacturer IC IC Manufacturer IC Sony CX20029 CDALA10M7GF062 Toko TK14581 CDALA10M7GA002 Sony CX20076 CDALA10M7GA063 Samsung KA2292 CDALA10M7GA004 Rohm BA4234L CDALA10M7GA064 Samsung KA2295 CDALA10M7GA005 Rohm BA4230AF CDALA10M7GA065 Samsung KA2298 CDALA10M7GA006 Toshiba TA7640AP CDALA10M7GA066 Rohm BA4110 CDALA10M7GA007 Sanyo LA1260 CDALA10M7GA067 Rohm BA4240L CDALA10M7GA008 Toshiba TA7303P CDALA10M7GA068 Sony CXA1991N CDALA10M7GA009 Toshiba TA7130P CDALA10M7GA069 Sony CXA1538M/N/S CDALA10M7GA011 Panasonic AN7004 CDALA10M7GA070 Sanyo LA1150 CDALA10M7GA012 Sony CXA1030P CDALA10M7GA071 Toshiba TA7765 CDALA10M7GA013 Panasonic AN7007SU CDALA10M7GF072 Toshiba TA31161 CDALA10M7GA014A Panasonic AN7006S CDALA10M7GA073 Motorola MC13158 Part Number CDALA10M7GA001 Part Number CDALA10M7GA015 Sanyo LA1816 CDALA10M7GA075 Sony CXA1611 CDALA10M7GA016 Toshiba TA8122AN/F CDALA10M7GA076 Sony CXA3067M CDALA10M7GA017 Philips TEA5591 CDALA10M7GA077 Toshiba TA2111 CDALA10M7GA018 Toshiba TA8132AN/AF CDALA10M7GA078 Sony CX1691M CDALA10M7GA019 Rohm BA1440 CDALA10M7GA079 Sanyo LA1838/M CDALA10M7GA020 Philips NE604 CDALA10M7GA080 Toshiba TA2104AFN CDALA10M7GF021A Philips TBA229-2 Toshiba TA2104F CDALA10M7GA022 Sanyo LA1810 CDALA10M7GA081 Telefunken U4313B CDALA10M7GA023 Sanyo LA7770 CDALA10M7GA082 Toshiba TA2099N CDALA10M7GF024 Philips TDA2557 CDALA10M7GA083 Sanyo LA1827 CDALA10M7GA025 Telefunken U829B CDALA10M7GA084 Rohm BH4126FV CDALA10M7GA026 Sanyo LA1805 CDALA10M7GA085 Philips SA639 CDALA10M7GA027 Sony CXA1238 CDALA10M7GA086 Sanyo LA1833 CDALA10M7GA027N CDALA10M7GA080A Sony CXA1238N CDALA10M7GA087 Motorola MC3363 CDALA10M7GA028 Telefunken U2501B CDALA10M7GA088 Toshiba TA8721ASN CDALA10M7GA029 Philips TBA120U CDALA10M7GA089 Samsung KA22425 CDALA10M7GA030 Philips TEA5592 CDALA10M7GA090 Samsung KA22901 CDALA10M7GA031 Toshiba TA2003 CDALA10M7GA091 Samsung KA2297 CDALA10M7GA032 Sony CXA1343M CDALA10M7GA092 Toshiba TA2132 CDALA10M7GA033 Toshiba TA2007N CDALA10M7GA092D Toshiba TA2132BP CXA1111 CDALA10M7GA034V Telefunken U4490B CDALA10M7GA093 Sony CDALA10M7GA035 Philips TEA5594 CDALA10M7GA094 Sanyo LA1822 CDALA10M7GA036 Toshiba TA2029 CDALA10M7GA095 Temic U2765B CDALA10M7GA037 Sanyo LA1830 CDALA10M7GA096 Philips SA636DK CDALA10M7GA038 Siemens TDA6160X CDALA10M7GA097 Matsushita AN6138SH CDALA10M7GA039 Toshiba TA8186 CDALA10M7GA098 Philips CAA3220TS CDALA10M7GA040 Philips TEA5710 CDALA10M7GA100 Toshiba TA2149N CDALA10M7GA041 Rohm BA4220 CDALA10M7GA100A Toshiba TA2149AN CDALA10M7GA042 Philips SA605 CDALA10M7GA101 Sanyo LA1823 CDALA10M7GA043 Sanyo LA1831 CDALA10M7GA102 Toshiba TA2142FN CDALA10M7GA044 Siemens TDA6160-2X CDALA10M7GA103 Samsung KB22902 CDALA10M7GA045 Toshiba TA2008A/AN CDALA10M7GA104 Rfmd RF2925 CDALA10M7GA046 Sanyo LA1832/M CDALA10M7GA105A Philips TEA5757HL CDALA10M7GA047 Philips SA626 CDALA10M7GA106 Fujitsu MB15G611 CDALA10M7GA048 Sanyo LA1835/M CDALA10M7GF107 Toshiba TA31272FN CDALA10M7GA049 Motorola MC13156 CDALA10M7GF108A Sanyo LA1225M CDALA10M7GA050 Toshiba TA2022 CDALA10M7GF109 Toko TK14588 CDALA10M7GA051 Siemens TDA1576T CDALA10M7GA110 Dspg DS9RF21 CDALA10M7GA052 Motorola MC13173 CDALA10M7GA053 Panasonic AN7232 CDALA10M7GA054 Sony CXA1376AM CDALA10M7CA001 CDALA10M7GA055 Philips TEA5712T CDALA10M7GA056 NEC µPC1391M CDALA10M7GA057 Toshiba CDALA10M7GA058 IC Manufacturer IC Sony CX20091 CDALA10M7CA002 Toshiba TA7687P/F CDALA10M7CA004A Motorola MC3356P TA2057 CDALA10M7CA005A Sanyo LA7770 Toshiba TA2046 CDALA10M7CA006 Philips TEA5591 CDALA10M7GA059 Samsung KA2244 CDALA10M7CA009 Toshiba TA7640AP CDALA10M7GA060 Rohm BA1448 CDALA10M7CA040 Philips TEA5710 CDALA10M7GA061 Philips TEA5762/5757 Part Number 53 13 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Example of Appllied Circuit ■ LA1140(Automotive Radio) L1 2.2µH AGC R7 200 C3 0.047 C7 0.047 VR1 150k C8 0.047 L2 SFELA10M7HAA0-B0 R4 10k R6 SFELA10M7HAA0-B0 330 C.F. 16 12 9 11 R13 12k 13 1 C1 0.022 0.047 C6 R8 330 FRONT END R2 C.F. 1.8k R3 C2 0.022 C4 1.8k R2 1k C5 AFC 7 + C9 0.047 C10 4.7µ LA1140 (SANYO) 2 + 8 3 4 5 6 14 22k 0.047 x 2 R9 220k R10 2.2µ C14 0.047 15 + C11 33p 10 R12 R1 100 Vref. R14 C13 33p R2 47k C15 ■ CXA1019M(Radio) FM PF FM OSC CERAMIC DISCRIMINATOR FM CERAFIL® (SFELA10M7FA00-B0) (CDALA10M7CA001-B0) W R 8 FM BPF AM ANT 12 IF FM IF OUT IN 6 14 17 7 FM FRONT END FM/AM BAND SELECT W 2 FM DISCRI FM IF AMP DETECTOR 19 METER 25 26 Vcc RIPPLE FILTER TUNING METER 13 REGULATOR 8 REG OUT W 28 13 1 CXA1019M(SONY) 10 11 AM FRONT END 5 18 AM IF AMP DETECTOR AM IF IN 20 16 22 AM OSC W AF PRE/POWER AMP VOL 23 DEP OUT 21 W 4 24 AF IN 27 W SP 3 W W AM CERAFIL® (SFULA455KU2B-B0) VOL No adjustment is needed the FM detection stage due to use the ceramic discriminator. Continued on the following page. 13 54 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Example of Appllied Circuit Continued from the preceding page. ■ TA8122F(Radio) CSBLA456KE2ZF16-B0 23 FM OSC 22 2 20 19 FM OSC AM OSC AF 3 PRE FM DET AM AGC AM MIX 4 5 AM AGC W BPF AM IF IN LPF2 VCO 16 15 Phase COM Phase COM VCO FM IF IN FM IF 8 FM DET 9 GND2 TUN LED 10 TUN LED 0.022µ L 0.015µ 14 OUT R R 4.7µ 13 HYX TA8122F(TOSHIBA) SW ST LED 11 12 ST LED QUAD 0.033µ 560 SFULA455KU2B-B0 4.7µ W W ST DECODER Freq Divider T2 10µH OUT L 17 L DET 7 0.015µ AM AM/FM MONO SW AM IF 6 Vcc2 0.1µ LPF1 18 33µ FM MIX MPX IN 21 AM MIX FM RF GND1 DEF OUT AM MIX AM RF 1 AM OSC W SFELA10M7FA00-B0 W CDALA 10M7GA16-B0 22µ OUT Vcc1 24 FM RF IN W W FM 560 AM PF IN FM PF MO 0.068µ 10µF 15p ST 22k T1 0.1µ L2 100k 8p 0.022µF 33k 5p 22p L1 20p L3 100k 330p IS2236 Vcc (3V) Detection and MPX stage adjustment ceramic discriminator and ceramic resonator (CERALOCK®) 13 55 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P61E7.pdf 01.10.17 Note: 1. Export Control For customers outside Japan Murata products should not be used or sold for use in the development, production, stockpiling or utilization of any conventional weapons or mass-destructive weapons (nuclear weapons, chemical or biological weapons, or missiles), or any other weapons. For customers in Japan For products which are controlled items subject to the “Foreign Exchange and Foreign Trade Law” of Japan, the export license specified by the law is required for export. < < > > 2. Please contact our sales representatives or product engineers before using our products listed in this catalog for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party's life, body or property, or when intending to use one of our products for other applications than specified in this catalog. q Aircraft equipment w Aerospace equipment e Undersea equipment r Power plant equipment t Medical equipment y Transportation equipment (vehicles, trains, ships, etc.) u Traffic signal equipment i Disaster prevention / crime prevention equipment o Data-processing equipment !0 Application of similar complexity and/or reliability requirements to the applications listed in the above 3. Product specifications in this catalog are as of May 2001. They are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before your ordering. If there are any questions, please contact our sales representatives or product engineers. 4. Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. 5. Please note that unless otherwise specified, we shall assume no responsibility whatsoever for any conflict or dispute that may occur in connection with the effect of our and/or third party's intellectual property rights and other related rights in consideration of your using our products and/or information described or contained in our catalogs. In this connection, no representation shall be made to the effect that any third parties are authorized to use the rights mentioned above under licenses without our consent. 6. None of ozone depleting substances (ODS) under the Montreal Protocol is used in manufacturing process of us. http://www.murata.co.jp/products/ Head Office 2-26-10, Tenjin Nagaokakyo-shi, Kyoto 617-8555, Japan Phone:81-75-951-9111 International Division 3-29-12, Shibuya, Shibuya-ku, Tokyo 150-0002, Japan Phone:81-3-5469-6123 Fax:81-3-5469-6155 E-mail:[email protected]