TI LMP2231BMAX/NOPB Single micropower, 1.6v, precision operational amplifier with cmos input Datasheet

LMP2231
www.ti.com
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
LMP2231 Single Micropower, 1.6V, Precision Operational Amplifier with CMOS Inputs
Check for Samples: LMP2231
FEATURES
1
(For VS = 5V, TA = 25°C, Typical Unless
Otherwise Noted)
23
•
•
•
•
•
•
•
•
•
•
•
•
•
Supply Current 10 µA
Operating Voltage Range 1.6V to 5.5V
TCVOS (LMP2231A) ±0.4 µV/°C (max)
TCVOS (LMP2231B) ±2.5µV/°C (max)
VOS ±150 µV (max)
Input Bias Current 20 fA
PSRR 120 dB
CMRR 97 dB
Open Loop Gain 120 dB
Gain Bandwidth Product 130 kHz
Slew Rate 58 V/ms
Input Voltage Noise, f = 1 kHz 60 nV/√Hz
Temperature Range –40°C to 125°C
APPLICATIONS
•
•
•
•
•
Precision Instrumentation Amplifiers
Battery Powered Medical Instrumentation
High Impedance Sensors
Strain Gauge Bridge Amplifier
Thermocouple Amplifiers
DESCRIPTION
The LMP2231 is a single micropower precision
amplifier designed for battery powered applications.
The 1.6V to 5.5V operating supply voltage range and
quiescent power consumption of only 16 μW extend
the battery life in portable battery operated systems.
The LMP2231 is part of the LMP™ precision amplifier
family. The high impedance CMOS input makes it
ideal for instrumentation and other sensor interface
applications.
The LMP2231 has a maximum offset of 150 µV and
maximum offset voltage drift of only 0.4 µV/°C along
with low bias current of only ±20 fA. These precise
specifications make the LMP2231 a great choice for
maintaining system accuracy and long term stability.
The LMP2231 has a rail-to-rail output that swings 15
mV from the supply voltage, which increases system
dynamic range. The common mode input voltage
range extends 200 mV below the negative supply,
thus the LMP2231 is ideal for use in single supply
applications with ground sensing.
The LMP2231 is offered in 5-Pin SOT-23 and 8-pin
SOIC packages.
The dual and quad versions of this product are also
available. The dual, LMP2232 is offered in 8-pin
SOIC and VSSOP. The quad, LMP2234 is offered in
14-pin SOIC and TSSOP.
1
2
3
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
LMP is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008–2013, Texas Instruments Incorporated
LMP2231
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
www.ti.com
Typical Application
+
+
V
V
3
LMP2231
+
2
6 LM4140A
1 PF
1,4,7,8
V
+
0.1 PF
V
+
+
½
LMP2232
-
R+'R
10 k:
12 k:
R
+
-
V
VA
IN
LMP2231
1 k:
R
10 PF
40 k:
+
ADC121S021
R+'R
+
V
-
12 k:
½
LMP2232
+
GND
10 k:
40 k:
Figure 1. Strain Gauge Bridge Amplifier
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings (1) (2)
ESD Tolerance
(3)
Human Body Model
2000V
Machine Model
100V
Differential Input Voltage
±300 mV
Supply Voltage (VS = V+ - V–)
6V
Voltage on Input/Output Pins
V+ + 0.3V, V– – 0.3V
Storage Temperature Range
−65°C to 150°C
Junction Temperature
(4)
150°C
For soldering specifications: see product folder at www.ti.com and http://www.ti.com/lit/SNOA549.
(1)
(2)
(3)
(4)
2
Absolute Maximum Ratings indicate limits beyond which damage may occur. Operating Ratings indicate conditions for which the device
is intended to be functional, but specific performance is not ensured. For ensured specifications and test conditions, see the Electrical
Characteristics.
If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications.
Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of
JEDEC)Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC).
The maximum power dissipation is a function of TJ(MAX), θJA. The maximum allowable power dissipation at any ambient temperature is
PD = (TJ(MAX) – TA)/ θJA. All numbers apply for packages soldered directly onto a PC Board.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
LMP2231
www.ti.com
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
Operating Ratings (1)
Operating Temperature Range
(2)
−40°C to 125°C
−
+
Supply Voltage (VS = V - V )
Package Thermal Resistance (θJA)
(1)
(2)
1.6V to 5.5V
(2)
5-Pin SOT-23
160.6 °C/W
8-Pin SOIC
116.2 °C/W
Absolute Maximum Ratings indicate limits beyond which damage may occur. Operating Ratings indicate conditions for which the device
is intended to be functional, but specific performance is not ensured. For ensured specifications and test conditions, see the Electrical
Characteristics.
The maximum power dissipation is a function of TJ(MAX), θJA. The maximum allowable power dissipation at any ambient temperature is
PD = (TJ(MAX) – TA)/ θJA. All numbers apply for packages soldered directly onto a PC Board.
5V DC Electrical Characteristics (1)
Unless otherwise specified, all limits ensured for TA = 25°C, V+ = 5V, V− = 0V, VCM = VO = V+/2, and RL > 1 MΩ. Boldface
limits apply at the temperature extremes.
Symbol
Typ (3)
Max (2)
Units
±10
±150
±230
μV
LMP2231A
±0.3
±0.4
μV/°C
LMP2231B
±0.3
±2.5
0.02
±1
±50
Parameter
VOS
Input Offset Voltage
TCVOS
Input Offset Voltage Drift
Conditions
Min (2)
IBIAS
Input Bias Current
IOS
Input Offset Current
CMRR
Common Mode Rejection Ratio
0V ≤ VCM ≤ 4V
81
80
97
PSRR
Power Supply Rejection Ratio
1.6V ≤ V+ ≤ 5.5V
V− = 0V, VCM = 0V
83
83
120
CMVR
Common Mode Voltage Range
CMRR ≥ 80 dB
CMRR ≥ 79 dB
−0.2
−0.2
AVOL
Large Signal Voltage Gain
VO = 0.3V to 4.7V
RL = 10 kΩ to V+/2
110
108
VO
Output Swing High
RL = 10 kΩ to V+/2
VIN(diff) = 100 mV
17
50
50
Output Swing Low
RL = 10 kΩ to V+/2
VIN(diff) = −100 mV
17
50
50
IO
IS
(1)
(2)
(3)
(4)
Output Current
(4)
pA
5
dB
dB
4.2
4.2
V
120
Sourcing, VO to V–
VIN(diff) = 100 mV
27
19
30
Sinking, VO to V+
VIN(diff) = −100 mV
17
12
22
Supply Current
fA
10
dB
mV
from either
rail
mA
16
18
µA
Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical
tables under conditions of internal self-heating where TJ > TA. Absolute Maximum Ratings indicate junction temperature limits beyond
which the device may be permanently degraded, either mechanically or electrically.
All limits are specified by testing, statistical analysis or design.
Typical values represent the most likely parametric norm at the time of characterization. Actual typical values may vary over time and
will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped production
material.
The short circuit test is a momentary open loop test.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
3
LMP2231
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
www.ti.com
5V AC Electrical Characteristics (1)
Unless otherwise specified, all limits ensured for TA = 25°C, V+ = 5V, V− = 0V, VCM = VO = V+/2, and RL > 1 MΩ. Boldface
limits apply at the temperature extremes.
Symbol
Parameter
Conditions
GBW
Gain-Bandwidth Product
CL = 20 pF, RL = 10 kΩ
SR
Slew Rate
AV = +1
Min (2)
Typ (3)
Max (2)
130
Falling Edge
33
32
58
Rising Edge
33
32
48
Units
kHz
V/ms
θm
Phase Margin
CL = 20 pF, RL = 10 kΩ
78
Gm
Gain Margin
CL = 20 pF, RL = 10 kΩ
27
dB
en
Input-Referred Voltage Noise Density
f = 1 kHz
60
nV/√Hz
deg
Input-Referred Voltage Noise
0.1 Hz to 10 Hz
2.3
μVPP
in
Input-Referred Current Noise
f = 1 kHz
10
fA/√Hz
THD+N
Total Harmonic Distortion + Noise
f = 100 Hz, RL = 10 kΩ
0.002
%
(1)
(2)
(3)
Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical
tables under conditions of internal self-heating where TJ > TA. Absolute Maximum Ratings indicate junction temperature limits beyond
which the device may be permanently degraded, either mechanically or electrically.
All limits are specified by testing, statistical analysis or design.
Typical values represent the most likely parametric norm at the time of characterization. Actual typical values may vary over time and
will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped production
material.
3.3V DC Electrical Characteristics (1)
Unless otherwise specified, all limits ensured for TA = 25°C, V+ = 3.3V, V− = 0V, VCM = VO = V+/2, and RL > 1 MΩ. Boldface
limits apply at the temperature extremes.
Symbol
Typ (3)
Max (2)
Units
±10
±160
±250
μV
LMP2231A
±0.3
±0.4
μV/°C
LMP2231B
±0.3
±2.5
0.02
±1
±50
Parameter
Conditions
Min (2)
VOS
Input Offset Voltage
TCVOS
Input Offset Voltage Drift
IBIAS
Input Bias Current
IOS
Input Offset Current
CMRR
Common Mode Rejection Ratio
0V ≤ VCM ≤ 2.3V
79
77
92
PSRR
Power Supply Rejection Ratio
1.6V ≤ V+ ≤ 5.5V
V− = 0V, VCM = 0V
83
83
120
CMVR
Common Mode Voltage Range
CMRR ≥ 78 dB
CMRR ≥ 77 dB
−0.2
−0.2
AVOL
Large Signal Voltage Gain
VO = 0.3V to 3V
RL = 10 kΩ to V+/2
108
107
VO
(1)
(2)
(3)
4
5
+
Output Swing High
RL = 10 kΩ to V /2
VIN(diff) = 100 mV
Output Swing Low
RL = 10 kΩ to V+/2
VIN(diff) = −100 mV
fA
dB
dB
2.5
2.5
120
14
14
pA
V
dB
50
50
50
50
mV
from either
rail
Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical
tables under conditions of internal self-heating where TJ > TA. Absolute Maximum Ratings indicate junction temperature limits beyond
which the device may be permanently degraded, either mechanically or electrically.
All limits are specified by testing, statistical analysis or design.
Typical values represent the most likely parametric norm at the time of characterization. Actual typical values may vary over time and
will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped production
material.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
LMP2231
www.ti.com
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
3.3V DC Electrical Characteristics(1) (continued)
Unless otherwise specified, all limits ensured for TA = 25°C, V+ = 3.3V, V− = 0V, VCM = VO = V+/2, and RL > 1 MΩ. Boldface
limits apply at the temperature extremes.
Symbol
IO
Output Current
IS
(4)
Conditions
Min (2)
Typ (3)
–
Sourcing, VO to V
VIN(diff) = 100 mV
11
8
14
Sinking, VO to V+
VIN(diff) = −100 mV
8
5
11
Parameter
(4)
Supply Current
10
Max (2)
Units
mA
15
16
µA
The short circuit test is a momentary open loop test.
3.3V AC Electrical Characteristics (1)
Unless otherwise is specified, all limits ensured for TA = 25°C, V+ = 3.3V, V− = 0V, VCM = VO = V+/2, and RL > 1 MΩ. Boldface
limits apply at the temperature extremes.
Symbol
Parameter
Conditions
Min (2)
Typ (3)
GBW
Gain-Bandwidth Product
CL = 20 pF, RL = 10 kΩ
128
SR
Slew Rate
AV = +1, CL = 20 pF
RL = 10 kΩ
Falling Edge
58
Rising Edge
48
Max (2)
Units
kHz
V/ms
θm
Phase Margin
CL = 20 pF, RL = 10 kΩ
76
Gm
Gain Margin
CL = 20 pF, RL = 10 kΩ
26
dB
en
Input-Referred Voltage Noise Density
f = 1 kHz
60
nV/√Hz
Input-Referred Voltage Noise
0.1 Hz to 10 Hz
2.4
μVPP
in
Input-Referred Current Noise
f = 1 kHz
10
fA/√Hz
THD+N
Total Harmonic Distortion + Noise
f = 100 Hz, RL = 10 kΩ
0.003
%
(1)
(2)
(3)
deg
Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical
tables under conditions of internal self-heating where TJ > TA. Absolute Maximum Ratings indicate junction temperature limits beyond
which the device may be permanently degraded, either mechanically or electrically.
All limits are specified by testing, statistical analysis or design.
Typical values represent the most likely parametric norm at the time of characterization. Actual typical values may vary over time and
will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped production
material.
2.5V DC Electrical Characteristics (1)
Unless otherwise specified, all limits ensured for TA = 25°C, V+ = 2.5V, V− = 0V, VCM = VO = V+/2, and RL > 1MΩ. Boldface
limits apply at the temperature extremes.
Symbol
VOS
Input Offset Voltage
TCVOS
Input Offset Voltage Drift
IBIAS
Input Bias Current
IOS
Input Offset Current
CMRR
Common Mode Rejection Ratio
(1)
(2)
(3)
Typ (3)
Max (2)
Units
±10
±190
±275
μV
LMP2231A
±0.3
±0.4
LMP2231B
±0.3
±2.5
0.02
±1.0
±50
Parameter
Conditions
Min (2)
μV/°C
5
0V ≤ VCM ≤ 1.5V
77
76
91
pA
fA
dB
Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical
tables under conditions of internal self-heating where TJ > TA. Absolute Maximum Ratings indicate junction temperature limits beyond
which the device may be permanently degraded, either mechanically or electrically.
All limits are specified by testing, statistical analysis or design.
Typical values represent the most likely parametric norm at the time of characterization. Actual typical values may vary over time and
will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped production
material.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
5
LMP2231
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
www.ti.com
2.5V DC Electrical Characteristics(1) (continued)
Unless otherwise specified, all limits ensured for TA = 25°C, V+ = 2.5V, V− = 0V, VCM = VO = V+/2, and RL > 1MΩ. Boldface
limits apply at the temperature extremes.
Symbol
Parameter
Conditions
+
Min (2)
Typ (3)
83
83
120
Max (2)
PSRR
Power Supply Rejection Ratio
1.6V ≤ V ≤ 5.5V
V− = 0V, VCM = 0V
CMVR
Common Mode Voltage Range
CMRR ≥ 77 dB
CMRR ≥ 76 dB
−0.2
−0.2
AVOL
Large Signal Voltage Gain
VO = 0.3V to 2.2V
RL = 10 kΩ to V+/2
104
104
VO
Output Swing High
RL = 10 kΩ to V+/2
VIN(diff) = 100 mV
12
50
50
Output Swing Low
RL = 10 kΩ to V+/2
VIN (diff) = −100 mV
13
50
50
IO
Output Current
IS
(4)
(4)
120
5
4
8
Sinking, VO to V+
VIN(diff) = −100 mV
3.5
2.5
7
Supply Current
dB
1.7
1.7
Sourcing, VO to V−
VIN(diff) = 100 mV
Units
V
dB
mV
from either
rail
mA
10
14
15
µA
The short circuit test is a momentary open loop test.
2.5V AC Electrical Characteristics (1)
Unless otherwise specified, all limits ensured for TA = 25°C, V+ = 2.5V, V− = 0V, VCM = VO = V+/2, and RL > 1MΩ. Boldface
limits apply at the temperature extremes.
Symbol
Parameter
Conditions
GBW
Gain-Bandwidth Product
CL = 20 pF, RL = 10 kΩ
SR
Slew Rate
AV = +1, CL = 20 pF
RL = 10 kΩ
Min (2)
Typ (3)
128
Falling Edge
58
Rising Edge
48
Max (2)
Units
kHz
V/ms
θm
Phase Margin
CL = 20 pF, RL = 10 kΩ
74
deg
Gm
Gain Margin
CL = 20 pF, RL = 10 kΩ
26
dB
en
Input-Referred Voltage Noise Density
f = 1 kHz
60
nV/√Hz
Input-Referred Voltage Noise
0.1 Hz to 10 Hz
2.5
μVPP
in
Input-Referred Current Noise
f = 1 kHz
10
fA/√Hz
THD+N
Total Harmonic Distortion + Noise
f = 100 Hz, RL = 10 kΩ
0.005
%
(1)
(2)
(3)
6
Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical
tables under conditions of internal self-heating where TJ > TA. Absolute Maximum Ratings indicate junction temperature limits beyond
which the device may be permanently degraded, either mechanically or electrically.
All limits are specified by testing, statistical analysis or design.
Typical values represent the most likely parametric norm at the time of characterization. Actual typical values may vary over time and
will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped production
material.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
LMP2231
www.ti.com
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
1.8V DC Electrical Characteristics
(1)
Unless otherwise specified, all limits ensured for TA = 25°C, V+ = 1.8V, V− = 0V, VCM = VO = V+/2, and RL > 1 MΩ. Boldface
limits apply at the temperature extremes.
Symbol
Typ (3)
Max (2)
Units
±10
±230
±325
μV
LMP2231A
±0.3
±0.4
LMP2231B
±0.3
±2.5
0.02
±1.0
±50
Parameter
VOS
Input Offset Voltage
TCVOS
Input Offset Voltage Drift
Min (2)
Conditions
IBIAS
Input Bias Current
IOS
Input Offset Current
CMRR
Common Mode Rejection Ratio
0V ≤ VCM ≤ 0.8V
76
75
92
PSRR
Power Supply Rejection Ratio
1.6V ≤ V+ ≤ 5.5V
V− = 0V, VCM = 0V
83
83
120
CMVR
Common Mode Voltage Rang
CMRR ≥ 76 dB
CMRR ≥ 75 dB
−0.2
0
AVOL
Large Signal Voltage Gain
VO = 0.3V to 1.5V
RL = 10 kΩ to V+/2
103
103
VO
Output Swing High
IO
Output Current
IS
(1)
(2)
(3)
(4)
(4)
pA
5
fA
dB
dB
1.0
1.0
V
120
RL = 10 kΩ to V+/2
VIN(diff) = 100 mV
dB
12
50
50
+
Output Swing Low
μV/°C
RL = 10 kΩ to V /2
VIN(diff) = −100 mV
50
50
13
Sourcing, VO to V−
VIN(diff) = 100 mV
2.5
2
5
Sinking, VO to V+
VIN(diff) = −100 mV
2
1.5
5
Supply Current
mV
from either
rail
mA
10
14
15
µA
Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical
tables under conditions of internal self-heating where TJ > TA. Absolute Maximum Ratings indicate junction temperature limits beyond
which the device may be permanently degraded, either mechanically or electrically.
All limits are specified by testing, statistical analysis or design.
Typical values represent the most likely parametric norm at the time of characterization. Actual typical values may vary over time and
will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped production
material.
The short circuit test is a momentary open loop test.
1.8V AC Electrical Characteristics (1)
Unless otherwise is specified, all limits ensured for TA = 25°C, V+ = 1.8V, V− = 0V, VCM = VO = V+/2, and RL > 1 MΩ. Boldface
limits apply at the temperature extremes.
Symbol
Parameter
Conditions
Min (2)
Typ (3)
GBW
Gain-Bandwidth Product
CL = 20 pF, RL = 10 kΩ
127
SR
Slew Rate
AV = +1, CL = 20 pF
RL = 10 kΩ
Falling Edge
58
Rising Edge
48
Max (2)
Units
kHz
V/ms
θm
Phase Margin
CL = 20 pF, RL = 10 kΩ
70
Gm
Gain Margin
CL = 20 pF, RL = 10 kΩ
25
dB
en
Input-Referred Voltage Noise Density
f = 1 kHz
60
nV/√Hz
Input-Referred Voltage Noise
0.1 Hz to 10 Hz
2.4
μVPP
(1)
(2)
(3)
deg
Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical
tables under conditions of internal self-heating where TJ > TA. Absolute Maximum Ratings indicate junction temperature limits beyond
which the device may be permanently degraded, either mechanically or electrically.
All limits are specified by testing, statistical analysis or design.
Typical values represent the most likely parametric norm at the time of characterization. Actual typical values may vary over time and
will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped production
material.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
7
LMP2231
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
www.ti.com
1.8V AC Electrical Characteristics(1) (continued)
Unless otherwise is specified, all limits ensured for TA = 25°C, V+ = 1.8V, V− = 0V, VCM = VO = V+/2, and RL > 1 MΩ. Boldface
limits apply at the temperature extremes.
Symbol
Parameter
Min (2)
Conditions
in
Input-Referred Current Noise
f = 1 kHz
THD+N
Total Harmonic Distortion + Noise
f = 100 Hz, RL = 10 kΩ
Typ (3)
Max (2)
Units
10
fA/√Hz
0.005
%
Connection Diagram
OUT
V
5
1
V
+
N/C
+
IN+
-
2
+
3
-
4
VIN
- 2
-
3
4
VIN
8
-
7
+
6
N/C
+
V
VOUT
INV
Figure 2. 5-Pin SOT-23 (Top View)
See Package Number DBV0005A
8
1
5
N/C
Figure 3. 8-Pin SOIC (Top View)
See Package Number D0008A
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
LMP2231
www.ti.com
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
Typical Performance Characteristics
Unless otherwise Specified: TA = 25°C, VS = 5V, VCM = VS/2, where VS = V+ - V−
Offset Voltage Distribution
TCVOS Distribution
10
16
VS = 5V
VS = 5V
VCM = VS/2
TA = 25°C
8
VCM = VS/2
12
PERCENTAGE (%)
PERCENTAGE (%)
14
10
8
6
4
-40°C d TA d 125°C
6
4
2
2
0
-150
-100
-50
0
50
100
0
-2.5 -2 -1.5 -1 -0.5 0 0.5 1 1.5 2 2.5
150
TCVOS (PV/°C)
VOS (PV)
Figure 4.
Figure 5.
Offset Voltage Distribution
TCVOS Distribution
10
14
VS = 3.3V
VCM = VS/2
10
8
6
4
-40°C d TA d 125°C
VS = 3.3V
8 VCM = VS/2
TA = 25°C
PERCENTAGE (%)
PERCENTAGE (%)
12
6
4
2
2
0
-150
-100
-50
0
50
100
0
-2.5 -2 -1.5 -1 -0.5 0 0.5 1 1.5 2 2.5
150
TCVOS (PV/°C)
VOS (PV)
Figure 6.
Figure 7.
Offset Voltage Distribution
TCVOS Distribution
10
14
VS = 2.5V
VCM = VS/2
TA = 25°C
8
VCM = VS/2
10
PERCENTAGE (%)
PERCENTAGE (%)
12
VS = 2.5V
8
6
4
-40°C d TA d 125°C
6
4
2
2
0
-150
-100
-50
0
50
100
150
0
-2.5 -2 -1.5 -1 -0.5 0 0.5 1 1.5 2 2.5
TCVOS (PV/°C)
VOS (PV)
Figure 8.
Figure 9.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
9
LMP2231
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
Unless otherwise Specified: TA = 25°C, VS = 5V, VCM = VS/2, where VS = V+ - V−
Offset Voltage Distribution
TCVOS Distribution
25
12
VS = 1.8V
VS = 1.8V
TA = 25°C
10
VCM = VS/2
20
PERCENTAGE (%)
PERCENTAGE (%)
VCM = VS/2
8
6
4
15
10
5
2
0
-150
-40°C d TA d 125°C
-100
-50
0
50
100
0
-2.5 -2 -1.5 -1 -0.5 0 0.5 1 1.5 2 2.5
150
TCVOS (PV/°C)
VOS (PV)
Figure 10.
Figure 11.
Offset Voltage vs.
VCM
Offset Voltage vs.
VCM
250
250
VS = 3.3V
-40°C
150
150
25°C
-40°C
25°C
85°C
50
125°C
-50
85°C
125°C
-50
-150
-150
-250
-0.2
50
VOS (PV)
OFFSET VOLTAGE (PV)
VS = 5V
0.8
1.8
2.8
3.8
-250
-0.2 0.2
4.3
0.6
1
1.4
1.8
VCM (V)
VCM (V)
Figure 12.
Figure 13.
Offset Voltage vs.
VCM
Offset Voltage vs.
VCM
VS = 2.5V
150
-40°C
-40°C
50
-50
25°C
50
VOS (PV)
VOS (PV)
85°C
85°C
-50
125°C
125°C
-150
-150
10
3
VS = 1.8V
25°C
-250
-0.2
2.6
250
250
150
2.2
0.2
0.6
1
1.4
1.8
2.2
-250
-0.2
0
0.2
0.4
0.6
0.8
VCM (V)
VCM (V)
Figure 14.
Figure 15.
Submit Documentation Feedback
1
1.2
1.4
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
LMP2231
www.ti.com
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
Typical Performance Characteristics (continued)
Unless otherwise Specified: TA = 25°C, VS = 5V, VCM = VS/2, where VS = V+ - V−
Offset Voltage vs.
Temperature
Offset Voltage vs.
Supply Voltage
120
VCM = 0V
5 TYPICAL PARTS
80
80
OFFSET VOLTAGE (PV)
OFFSET VOLTAGE (PV)
100
VS = 1.8V, 2.5V, 3.3V, 5V
100
60
40
20
0
-20
-40
60
-40°C
40
25°C
20
0
85°C
-20
-60
-80
-40 -20
125°C
0
20
40
60
80 100 120
TEMPERATURE (°C)
-40
1.5
2
2.5
3
3.5
4
4.5
5
5.5
SUPPLY VOLTAGE (V)
Figure 16.
Figure 17.
Time Domain Voltage Noise
Time Domain Voltage Noise
Figure 18.
Figure 19.
Time Domain Voltage Noise
Time Domain Voltage Noise
Figure 20.
Figure 21.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
11
LMP2231
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
Unless otherwise Specified: TA = 25°C, VS = 5V, VCM = VS/2, where VS = V+ - V−
Input Bias Current vs.
VCM
Input Bias Current vs.
VCM
10
40
VS = 2V
INPUT BIAS CURRENT (pA)
INPUT BIAS CURRENT (fA)
25°C
20
10
0
-40°C
-10
-20
6
4
85°C
2
0
-2
-6
-8
-40
-10
0.25
0.5
1
0.75
1.25
125°C
-4
-30
0
VS = 2V
8
30
0
1.5
0.25
0.5
0.75
1.25
Figure 22.
Figure 23.
Input Bias Current vs.
VCM
Input Bias Current vs.
VCM
40
10
VS = 2.5V
20
-40°C
10
0
-10
-20
25°C
VS = 2.5V
8
INPUT BIAS CURRENT (pA)
30
6
4
85°C
2
0
-2
-4
125°C
-6
-30
-8
-40
0
0.5
1
1.5
-10
2
0
0.5
1
VCM (V)
1.5
Figure 25.
Input Bias Current vs.
VCM
Input Bias Current vs.
VCM
20
VS = 3.3V
VS = 3.3V
15
50
INPUT BIAS CURRENT (pA)
75
INPUT BIAS CURRENT (fA)
2
VCM (V)
Figure 24.
100
25°C
25
0
-40°C
-25
-50
-75
10
125°C
5
0
85°C
-5
-10
-15
-100
-20
0
12
1.5
VCM (V)
VCM (V)
INPUT BIAS CURRENT (fA)
1
0.5
1
1.5
2
2.5
0
0.5
1
1.5
VCM (V)
VCM (V)
Figure 26.
Figure 27.
Submit Documentation Feedback
2
2.5
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
LMP2231
www.ti.com
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
Typical Performance Characteristics (continued)
Unless otherwise Specified: TA = 25°C, VS = 5V, VCM = VS/2, where VS = V+ - V−
Input Bias Current vs.
VCM
Input Bias Current vs.
VCM
600
30
VS = 5V
400
300
200
25°C
100
0
-100
-40°C
-200
1
3
2
20
125°C
15
10
5
0
-5
85°C
-10
-15
-20
-25
-30
-300
0
VS = 5V
25
INPUT BIAS CURRENT (pA)
INPUT BIAS CURRENT (fA)
500
4
0
1
2
VCM (V)
3
4
VCM (V)
Figure 28.
Figure 29.
PSRR vs.
Frequency
Supply Current vs.
Supply Voltage
11
0
VS = 2V, 2.5V, 3.3V, 5V
-20
PSRR (dB)
SUPPLY CURRENT (PA)
10
-40
+PSRR
-60
-80
-100
VS = 2V
-PSRR
-120
-140
-160
10
125°C
85°C
9
25°C
8
-40°C
7
6
VS = 5V
100
1k
10k
100k
FREQUENCY (Hz)
5
1.5
2.5
3.5
4.5
5.5
SUPPLY VOLTAGE (V)
Figure 30.
Figure 31.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
13
LMP2231
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
Unless otherwise Specified: TA = 25°C, VS = 5V, VCM = VS/2, where VS = V+ - V−
Sinking Current vs.
Supply Voltage
Sourcing Current vs.
Supply Voltage
30
40
35
25
30
-40°C
-40°C
ISOURCE (mA)
ISINK (mA)
20
25°C
15
85°C
10
25
25°C
20
125°C
125°C
10
5
5
0
1.5
2.5
3.5
4.5
0
1.5
5.5
SUPPLY VOLTAGE (V)
2.5
3.5
4.5
5.5
SUPPLY VOLTAGE (V)
Figure 32.
Figure 33.
Output Swing High vs.
Supply Voltage
Output Swing Low vs.
Supply Voltage
30
25
RL = 10 k:
RL = 10 k:
20
85°C
25°C
15
85°C
20
15
10
2.5
3.5
4.5
5
1.5
5.5
2.5
Figure 34.
4.5
5.5
Figure 35.
Open Loop Frequency Response
100
PHASE
3.5
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
Open Loop Frequency Response
120
100
90
75
90
50
60
120
PHASE
-40°C
25°C
75
-40°C
25°C
-40°C
10
1.5
125°C
25
VOUT FROM RAIL (mV)
125°C
VOUT FROM RAIL (mV)
85°C
15
-40°C
25
30
GAIN
30
25
PHASE (°)
60
GAIN
GAIN (dB)
125°C
50
PHASE (°)
GAIN (dB)
85°C
25°C
0
125°C
VS = 5V
0
0
RL = 10 k:
CL = 20 pF
-25
10
100
14
VS = 1.8V, 2.5V, 3.3V, 5V
0
RL = 10 k:, 100 k:, 10 M:
85°C
1k
10k
100k
-30
1M
CL = 20 pF, 50 pF, 100 pF
-25
10k
1k
10
100
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 36.
Figure 37.
Submit Documentation Feedback
100k
-30
1M
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
LMP2231
www.ti.com
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
Typical Performance Characteristics (continued)
Unless otherwise Specified: TA = 25°C, VS = 5V, VCM = VS/2, where VS = V+ - V−
Phase Margin vs.
Capacitive Load
90
Slew Rate vs.
Supply Voltage
60
VS = 5V
RL = 100 k:
SLEW RATE (V/ms)
PHASE MARGIN (°)
VS = 1.8V
VS = 2.5V
70
60
50
20
52
48
RISING EDGE
44
RL = 10 k:
VS = 3.3V
40
60
FALLING EDGE
56
80
80
40
1.5
100
2
2.5
3
3.5
4
4.5
CAPACITIVE LOAD (pF)
SUPPLY VOLTAGE (V)
Figure 38.
Figure 39.
THD+N vs.
Amplitude
THD+N vs.
Frequency
10
5
5.5
1
RL = 10 k:
CL = 20 pF
0.1
1
VS = 2V
VS = 2.5V
THD+N (%)
THD+N (%)
VS = 2V
0.1
0.01
VS = 3.3V
RL = 10 k:
VO = VS ± 1V
VS = 2.5V
0.01
0.001
VS = 3.3V
VS = 5V
VS = 5V
CL = 20 pF
f = 1 kHz
0.001
0.01
0.1
1
10
0.0001
1
100
1k
10k
Figure 40.
Figure 41.
Large Signal Step Response
Small Signal Step Response
VS = 5V
VIN = 2 VPP
f = 1 kHz
AV = +1
50 mV/DIV
500 mV/DIV
10
100k
FREQUENCY (Hz)
VOUT (VPP)
VS = 5V
VIN = 200 mVPP
f = 1 kHz
AV = +1
RL = 10 k:
RL = 10 k:
CL = 20 pF
CL = 20 pF
100 Ps/DIV
100 Ps/DIV
Figure 42.
Figure 43.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
15
LMP2231
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
Unless otherwise Specified: TA = 25°C, VS = 5V, VCM = VS/2, where VS = V+ - V−
Small Signal Step Response
100 mV/DIV
Large Signal Step Response
1V/DIV
VS = 5V
VIN = 400 mVPP
f = 1 kHz
AV = +10
VS = 5V
VIN = 50 mVPP
f = 1 kHz
AV = +10
RL = 10 k:
RL = 10 k:
CL = 20 pF
CL = 20 pF
100 Ps/DIV
100 Ps/DIV
Figure 44.
Figure 45.
CMRR
vs.
Frequency
Input Voltage Noise
vs.
Frequency
140
1000
VS = 5V
VS = 2.5V
120
VOLTAGE NOISE nV/ Hz)
VS = 3.3V
CMRR (dB)
100
80
VS = 5V
60
40
20
0
10
100
1k
10k
100k
10
1
1
10
100
1k
10k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 46.
16
100
Figure 47.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
LMP2231
www.ti.com
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
APPLICATION INFORMATION
LMP2231
The LMP2231 is a single CMOS precision amplifier that offer low offset voltage and low offset voltage drift, and
high gain while only consuming 10 μA of current per channel.
The LMP2231 is a micropower op amp, consuming only 10 μA of current. Micropower op amps extend the run
time of battery powered systems and reduce energy consumption in energy limited systems. The ensured supply
voltage range of 1.8V to 5.0V along with the ultra-low supply current extend the battery run time in two ways. The
extended ensured power supply voltage range of 1.8V to 5.0V enables the op amp to function when the battery
voltage has depleted from its nominal value down to 1.8V. In addition, the lower power consumption increases
the life of the battery.
The LMP2231 has an input referred offset voltage of only ±150 μV maximum at room temperature. This offset is
ensured to be less than ±230 μV over temperature. This minimal offset voltage along with very low TCVOS of only
0.3 µV/°C typical allows more accurate signal detection and amplification in precision applications.
The low input bias current of only ±20 fA gives the LMP2231 superiority for use in high impedance sensor
applications. Bias Current of an amplifier flows through source resistance of the sensor and the voltage resulting
from this current flow appears as a noise voltage on the input of the amplifier. The low input bias current enables
the LMP2231 to interface with high impedance sensors while generating negligible voltage noise. Thus the
LMP2231 provides better signal fidelity and a higher signal-to-noise ration when interfacing with high impedance
sensors.
Texas Instruments is heavily committed to precision amplifiers and the market segment they serve. Technical
support and extensive characterization data is available for sensitive applications or applications with a
constrained error budget.
The operating supply voltage range of 1.8V to 5.5V over the extensive temperature range of −40°C to 125°C
makes the LMP2231 an excellent choice for low voltage precision applications with extensive temperature
requirements.
The LMP2231 is offered in the space saving 5-Pin SOT-23 and 8-pin SOIC package. These small packages are
ideal solutions for area constrained PC boards and portable electronics.
TOTAL NOISE CONTRIBUTION
The LMP2231 has a very low input bias current, very low input current noise, and low input voltage noise for
micropower amplifier. As a result, this amplifier makes a great choice for circuits with high impedance sensor
applications.
Figure 48 shows the typical input noise of the LMP2231 as a function of source resistance where:
en denotes the input referred voltage noise
ei is the voltage drop across source resistance due to input referred current noise or ei = RS * in
et shows the thermal noise of the source resistance
eni shows the total noise on the input.
Where:
eni =
2
2
2
en + ei + et
The input current noise of the LMP2231 is so low that it will not become the dominant factor in the total noise
unless source resistance exceeds 300 MΩ, which is an unrealistically high value. As is evident in Figure 48, at
lower RS values, total noise is dominated by the amplifier’s input voltage noise. Once RS is larger than a 100 kΩ,
then the dominant noise factor becomes the thermal noise of RS. As mentioned before, the current noise will not
be the dominant noise factor for any practical application.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
17
LMP2231
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
www.ti.com
VOLTAGE NOISE DENSITY (nV/ Hz)
1000
eni
en
100
et
10
ei
1
0.1
10
100
1k
10k
100k
1M
10M
RS (:)
Figure 48. Total Input Noise
VOLTAGE NOISE REDUCTION
The LMP2231 has an input voltage noise of 60 nV/√Hz . While this value is very low for micropower amplifiers,
this input voltage noise can be further reduced by placing N amplifiers in parallel as shown in Figure 49. The total
voltage noise on the output of this circuit is divided by the square root of the number of amplifiers used in this
parallel combination. This is because each individual amplifier acts as an independent noise source, and the
average noise of independent sources is the quadrature sum of the independent sources divided by the number
of sources. For N identical amplifiers, this means:
REDUCED INPUT VOLTAGE NOISE =
1
N
en1+en2+
=
1
N
Nen =
=
1
2
2
2
2
+enN
N
en
N
en
N
Figure 49 shows a schematic of this input voltage noise reduction circuit. Typical resistor values are: RG = 10Ω,
RF = 1 kΩ, and RO = 1 kΩ.
18
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
LMP2231
www.ti.com
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
+
V
+
-
VIN
VOUT
-
RG
RO
V
RF
+
V
+
RG
V
-
RO
RF
+
V
+
RG
V
-
RO
RF
+
V
+
RG
V
-
RO
RF
Figure 49. Noise Reduction Circuit
PRECISION INSTRUMENTATION AMPLIFIER
Measurement of very small signals with an amplifier requires close attention to the input impedance of the
amplifier, gain of the overall signal on the inputs, and the gain on each input of the amplifier. This is because the
difference of the input signal on the two inputs is of the interest and the common signal is considered noise. A
classic circuit implementation is an instrumentation amplifier. Instrumentation amplifiers have a finite, accurate,
and stable gain. They also have extremely high input impedances and very low output impedances. Finally they
have an extremely high CMRR so that the amplifier can only respond to the differential signal. A typical
instrumentation amplifier is shown in Figure 50.
V1
+
V01
-
R2
KR2
R1
R1
R11 = a
+
R1
V2
+
VOUT
V02
R2
KR2
Figure 50. Instrumentation Amplifier
There are two stages in this amplifier. The last stage, output stage, is a differential amplifier. In an ideal case the
two amplifiers of the first stage, input stage, would be set up as buffers to isolate the inputs. However they
cannot be connected as followers because of mismatch of amplifiers. That is why there is a balancing resistor
between the two. The product of the two stages of gain will give the gain of the instrumentation amplifier. Ideally,
the CMRR should be infinite. However the output stage has a small non-zero common mode gain which results
from resistor mismatch.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
19
LMP2231
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
www.ti.com
In the input stage of the circuit, current is the same across all resistors. This is due to the high input impedance
and low input bias current of the LMP2231.
GIVEN: I R = I R
11
1
(1)
By Ohm’s Law:
VO1 - VO2 = (2R1 + R11) IR
11
= (2a + 1) R11 x IR
11
= (2a + 1) V R
11
(2)
However:
VR
11 = V1 - V2
(3)
So we have:
VO1–VO2 = (2a+1)(V1–V2)
(4)
Now looking at the output of the instrumentation amplifier:
KR2
VO =
R2
(VO2 - VO1)
= -K (VO1 - VO2)
(5)
Substituting from Equation 4:
VO = -K (2a + 1) (V1 - V2)
(6)
This shows the gain of the instrumentation amplifier to be:
−K(2a+1)
(7)
Typical values for this circuit can be obtained by setting: a = 12 and K= 4. This results in an overall gain of −100.
SINGLE SUPPLY STRAIN GAGE BRIDGE AMPLIFIER
Strain gauges are popular electrical elements used to measure force or pressure. Strain gauges are subjected to
an unknown force which is measured as a the deflection on a previously calibrated scale. Pressure is often
measured using the same technique; however this pressure needs to be converted into force using an
appropriate transducer. Strain gauges are often resistors which are sensitive to pressure or to flexing. Sense
resistor values range from tens of ohms to several hundred kilo ohms. The resistance change which is a result of
applied force across the strain gauge might be 1% of its total value. An accurate and reliable system is needed
to measure this small resistance change. Bridge configurations offer a reliable method for this measurement.
Bridge sensors are formed of four resistors, connected as a quadrilateral. A voltage source or a current source is
used across one of the diagonals to excite the bridge while a voltage detector across the other diagonal
measures the output voltage.
Bridges are mainly used as null circuits or to measure a differential voltages. Bridges will have no output voltage
if the ratios of two adjacent resistor values are equal. This fact is used in null circuit measurements. These are
particularly used in feedback systems which involve electrochemical elements or human interfaces. Null systems
force an active resistor, such as a strain gauge, to balance the bridge by influencing the measured parameter.
Often in sensor applications at lease one of the resistors is a variable resistor, or a sensor. The deviation of this
active element from its initial value is measured as an indication of change in the measured quantity. A change in
output voltage represents the sensor value change. Since the sensor value change is often very small, the
resulting output voltage is very small in magnitude as well. This requires an extensive and very precise
amplification circuitry so that signal fidelity does not change after amplification.
Sensitivity of a bridge is the ratio of its maximum expected output change to the excitation voltage change.
20
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
LMP2231
www.ti.com
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
Figure 51 (a) shows a typical bridge sensor and Figure 51(b) shows the bridge with four sensors. R in
Figure 51(b) is the nominal value of the sense resistor and the deviations from R are proportional to the quantity
being measured.
R1
R + 'R
R2
EXCITATION
SOURCE
VOUT
R3
R - 'R
EXCITATION
SOURCE
VOUT
R4
R - 'R
R + 'R
(b)
(a)
§
R
¨1 + 3
¨
R1
©
R4
-
VOUT =
R2
§
¨
¨
©
VOUT =
R1
§
R
¨1 + 4
¨
R2
©
§
¨
¨
©
R3
'R
R
x VSOURCE
x VSOURCE
Figure 51. Bridge Sensor
Instrumentation amplifiers are great for interfacing with bridge sensors. Bridge sensors often sense a very small
differential signal in the presence of a larger common mode voltage. Instrumentation amplifiers reject this
common mode signal.
Figure 52 shows a strain gauge bridge amplifier. In this application the LMP2231 is used to buffer the LM4140's
precision output voltage. The LM4140A is a precision voltage reference. The other three LMP2231s are used to
form an instrumentation amplifier. This instrumentation amplifier uses the LMP2231's high CMRR and low VOS
and TCVOS to accurately amplify the small differential signal generated by the output of the bridge sensor. This
amplified signal is then fed into the ADC121S021 which is a 12-bit analog to digital converter. This circuit works
on a single supply voltage of 5V.
+
+
V
V
3
LMP2231
+
2
6 LM4140A
1 PF
1,4,7,8
V
+
0.1 PF
V
+
+
½
LMP2232
-
R+'R
10 k:
12 k:
R
+
-
V
LMP2231
1 k:
R
10 PF
40 k:
VA
IN
+
R+'R
ADC121S021
+
V
-
12 k:
½
LMP2232
+
GND
10 k:
40 k:
Figure 52. Strain Gauge Bridge Amplifier
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
21
LMP2231
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
www.ti.com
PORTABLE GAS DETECTION SENSOR
Gas sensors are used in many different industrial and medical applications. They generate a current which is
proportional to the percentage of a particular gas sensed in an air sample. This current goes through a load
resistor and the resulting voltage drop is measured. Depending on the sensed gas and sensitivity of the sensor,
the output current can be in the order of tens of microamperes to a few milliamperes. Gas sensor datasheets
often specify a recommended load resistor value or they suggest a range of load resistors to choose from.
Oxygen sensors are used when air quality or oxygen delivered to a patient needs to be monitored. Fresh air
contains 20.9% oxygen. Air samples containing less than 18% oxygen are considered dangerous. Oxygen
sensors are also used in industrial applications where the environment must lack oxygen. An example is when
food is vacuum packed. There are two main categories of oxygen sensors, those which sense oxygen when it is
abundantly present (i.e. in air or near an oxygen tank) and those which detect traces of oxygen in ppm.
Figure 53 shows a typical circuit used to amplify the output of an oxygen detector. The LMP2231 makes an
excellent choice for this application as it only draws 10 µA of current and operates on supply voltages down to
1.8V. This application detects oxygen in air. The oxygen sensor outputs a known current through the load
resistor. This value changes with the amount of oxygen present in the air sample. Oxygen sensors usually
recommend a particular load resistor value or specify a range of acceptable values for the load resistor. Oxygen
sensors typically have a life of one to two years. The use of the micropower LMP2231 means minimal power
usage by the op amp and it enhances the battery life. Depending on other components present in the circuit
design, the battery could last for the entire life of the oxygen sensor. The precision specifications of the
LMP2231, such as its very low offset voltage, low TCVOS , low input bias current, low CMRR, and low PSRR are
other factors which make the LMP2231 a great choice for this application.
99 k:
+
V
1 k:
VOUT
1 k:
+
V
-
RL
OXYGEN SENSOR
Figure 53. Precision Oxygen Sensor
22
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
LMP2231
www.ti.com
SNOSB01E – JANUARY 2008 – REVISED MARCH 2013
REVISION HISTORY
Changes from Revision D (March 2013) to Revision E
•
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 22
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2231
23
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
LMP2231AMA/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LMP22
31AMA
LMP2231AMAE/NOPB
ACTIVE
SOIC
D
8
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LMP22
31AMA
LMP2231AMAX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LMP22
31AMA
LMP2231AMF/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
AL5A
LMP2231AMFE/NOPB
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
AL5A
LMP2231AMFX/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
AL5A
LMP2231BMA/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LMP22
31BMA
LMP2231BMAE/NOPB
ACTIVE
SOIC
D
8
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LMP22
31BMA
LMP2231BMAX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LMP22
31BMA
LMP2231BMF/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
AL5B
LMP2231BMFE/NOPB
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
AL5B
LMP2231BMFX/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
AL5B
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
8-Apr-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
LMP2231AMAE/NOPB
Package Package Pins
Type Drawing
SOIC
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
D
8
250
178.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LMP2231AMAX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LMP2231AMF/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LMP2231AMFE/NOPB
SOT-23
DBV
5
250
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LMP2231AMFX/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LMP2231BMAE/NOPB
SOIC
D
8
250
178.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LMP2231BMAX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LMP2231BMF/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LMP2231BMFE/NOPB
SOT-23
DBV
5
250
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LMP2231BMFX/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
8-Apr-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LMP2231AMAE/NOPB
SOIC
D
LMP2231AMAX/NOPB
SOIC
D
8
250
210.0
185.0
35.0
8
2500
367.0
367.0
35.0
LMP2231AMF/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LMP2231AMFE/NOPB
SOT-23
DBV
5
250
210.0
185.0
35.0
LMP2231AMFX/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LMP2231BMAE/NOPB
SOIC
D
8
250
210.0
185.0
35.0
LMP2231BMAX/NOPB
SOIC
D
8
2500
367.0
367.0
35.0
LMP2231BMF/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LMP2231BMFE/NOPB
SOT-23
DBV
5
250
210.0
185.0
35.0
LMP2231BMFX/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated