NICHIA STS-DA1-2009E <Cat.No.120828> NICHIA CORPORATION SPECIFICATIONS FOR WARM WHITE LED NVSL219BT ● Pb-free Reflow Soldering Application ● Built-in ESD Protection Device ● RoHS Compliant NICHIA STS-DA1-2009E <Cat.No.120828> SPECIFICATIONS (1) Absolute Maximum Ratings Symbol Absolute Maximum Rating Unit Forward Current Item IF 1500 mA Pulse Forward Current IFP 2000 mA Allowable Reverse Current IR 85 mA Power Dissipation PD 5.4 W Operating Temperature Topr -40~100 °C Storage Temperature Tstg -40~100 °C Junction Temperature TJ 150 °C * Absolute Maximum Ratings at TS=25°C. * IFP conditions with pulse width ≤10ms and duty cycle ≤10%. (2) Initial Electrical/Optical Characteristics Item Symbol Forward Voltage R70 VF Luminous Flux Φv Luminous Intensity Iv Color Rendering Index Chromaticity Coordinate R8000 Condition Typ Max IF=700mA 3.13 - IF=350mA 2.95 - IF=700mA 260 - IF=350mA 140 - Unit V lm IF=700mA 71 - IF=350mA 38 - Ra IF=700mA 73 - - x - IF=700mA 0.3817 - - y - IF=700mA 0.3795 - - IF=700mA 220 - IF=350mA 117 - IF=700mA 62 - IF=350mA 33 - cd Luminous Flux Φv Luminous Intensity Iv Color Rendering Index Ra IF=700mA 83 - - - IF=700mA 0.4100 - - - IF=700mA 0.3900 - - RθJS - 6 11 °C/W Chromaticity Coordinate Thermal Resistance x y lm cd * Characteristics at TS=25°C. * Luminous Flux value as per CIE 127:2007 standard. * Chromaticity Coordinates as per CIE 1931 Chromaticity Chart. * RθJS is Thermal Resistance from junction to TS measuring point. 1 NICHIA STS-DA1-2009E <Cat.No.120828> RANKS Item Rank Forward Voltage Condition Min Max M2 3.4 3.6 M1 3.2 3.4 3.0 3.2 IF=700mA L2 L1 2.8 3.0 D260 260 280 240 260 220 240 200 220 180 200 70 - D240 Luminous Flux IF=700mA D220 D200 D180 R70 Color Rendering Index Ra R8000 IF=700mA Ra Unit V lm - 80 - - 0 - - R9 Color Ranks Rank d1 x 0.3575 0.3610 0.3780 0.3988 0.3897 0.3720 y 0.3612 0.3850 0.3970 0.4116 0.3823 0.3714 x 0.3545 0.3575 0.3720 0.3897 0.3822 0.3667 y 0.3408 0.3612 0.3714 0.3823 0.3580 0.3484 Rank d2 Rank sw27 Rank sw30 x 0.4373 0.4562 0.4813 0.4593 x 0.4147 0.4299 0.4562 0.4373 y 0.3893 0.4260 0.4319 0.3944 y 0.3814 0.4165 0.4260 0.3893 x 0.3898 0.3996 0.4299 0.4147 x 0.3670 0.3736 0.3996 0.3898 y 0.3716 0.4015 0.4165 0.3814 y 0.3578 0.3874 0.4015 0.3716 Rank sw35 Rank sw40 Rank sw45 x 0.3515 0.3548 0.3736 0.3670 y 0.3487 0.3736 0.3874 0.3578 * Ranking at TS=25°C. * Forward Voltage Tolerance: ±0.05V * Luminous Flux Tolerance: ±7% * Color Rendering Index Ra Tolerance: ±2 * Color Rendering Index R9 Tolerance: ±6.5 * The R9 value for the above rank shall be greater than 0. * Chromaticity Coordinate Tolerance: ±0.005 * LEDs from the above ranks will be shipped. The rank combination ratio per shipment will be decided by Nichia. 2 NICHIA STS-DA1-2009E <Cat.No.120828> Luminous Flux Ranks by Color Rank, Color Rendering Index Rank Ranking by Luminous Flux Ranking by D180 D200 D220 D240 D260 Color Coordinates, Color Rendering Index d1,d2 R70 sw27 R8000 sw30,sw35 R8000 sw40,sw45 R8000 3 NICHIA STS-DA1-2009E <Cat.No.120828> CHROMATICITY DIAGRAM 0.50 0.45 d1 y sw27 sw30 0.40 sw35 sw40 sw45 0.35 d2 0.30 0.30 0.35 0.40 0.45 0.50 x 4 NICHIA STS-DA1-2009E <Cat.No.120828> OUTLINE DIMENSIONS * 本製品はRoHS指令に適合しております。 This product complies with RoHS Directive. 管理番号 No. NVSL219B STS-DA7-1785 (単位 Unit:±0.2) mm) (単位 Unit: mm, 公差 Tolerance: 3.5 2.9 3.5 0.4 2 Cathode Mark 3.2 2.4 1 0.45 3.2 0.5 1.3 Cathode 項目 Item 内容 Description パッケージ材質 Package Materials セラミックス Ceramics 封止樹脂材質 Encapsulating Resin Materials シリコーン樹脂 （蛍光体入り） Silicone Resin (with phosphor) 電極材質 Electrodes Materials 金メッキ Au-plated レンズ材質 Lens Materials シリコーン樹脂 Silicone Resin ダイヒートシンク材質 Die Heat Sink Materials 金メッキ Au-plated 質量 Weight 0.031g (TYP) Anode ダイヒートシンク Die Heat Sink 保護素子 Protection Device K A 5 NICHIA STS-DA1-2009E <Cat.No.120828> SOLDERING • Recommended Reflow Soldering Condition(Lead-free Solder) 1 to 5°C per sec 260°C Max 10sec Max Pre-heat 180 to 200°C 60sec Max Above 220°C 120sec Max ● Recommended Soldering Pad Pattern 0.5 3.3 1.3 1.2 0.4 0.5 (単位 Unit: mm) 4.1 0.4 1.9 * This LED is designed to be reflow soldered on to a PCB. If dip soldered or hand soldered, Nichia cannot guarantee its reliability. * Reflow soldering must not be performed more than twice. * Avoid rapid cooling. Ramp down the temperature gradually from the peak temperature. * Nitrogen reflow soldering is recommended. Air flow soldering conditions can cause optical degradation, caused by heat and/or atmosphere. * Since the silicone used in the encapsulating resin is soft, do not press on the encapsulant resin. Pressure can cause nicks, chip-outs, encapsulant delamination and deformation, and bump breaks, decreasing reliability. When using automatic pick and place machine, use a pick up nozzle which does not directly apply stress to the encapsulation of the LEDs. Recommended conditions: It is recommended to use a pick up nozzle designed for the LEDs. (See Figure below.) * Avoid direct contact to the resin lens with the picking up nozzle. Failure to comply might result in catastrophic failure of the LEDs due to bump damage or breakage. 3.5 4.5 (単位 Unit: mm) * Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable, a hot plate should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. * The Die Heat Sink should be soldered to customer PCB. If it is difficult or impossible, use high heat-dissipating adhesive. * When soldering, do not apply stress to the LED while the LED is hot. * This product uses an electrode pad design which improves thermal shock resistance. After mounting, it is recommended to check if the solder fillets are properly formed on the sides of the pads. 6 NICHIA STS-DA1-2009E <Cat.No.120828> TAPE AND REEL DIMENSIONS テーピング部 Tape 1.75±0.1 2±0.054±0.1 5.5±0.05 Cathode Mark Nxxx219x STS-DA7-1728 (単位 Unit: mm) 0.25±0.05 3.7±0.1 8±0.1 12+0.3 -0.1 Φ1.5+0.1 -0 管理番号 No. 2.25±0.1 Φ 1.5+0.2 -0 3.7±0.1 エンボスキャリアテープ Embossed Carrier Tape トレーラ部/リーダ部 Trailer and Leader トップカバーテープ Top Cover Tape 引き出し方向 Feed Direction トレーラ部最小160mm（空部） Trailer 160mm MIN(Empty Pockets) LED装着部 Loaded Pockets 引き出し部最小100mm（空部） Leader with Top Cover Tape 100mm MIN(Empty Pocket) リーダ部最小400mm Leader without Top Cover Tape 400mm MIN リール部 Reel 330±2 17.5±1 13.5±1 * 数量は1リールにつき 3500個入りです。 Reel Size: 3500pcs * JIS C 0806電子部品テーピングに準拠しています。 Φ 21 ± The tape packing method complies with JIS C 0806 (Packaging of Electronic Components on Continuous Tapes). Φ1 3 ±0 . 2 Φ80±1 0. 8 ラベル Label 7 NICHIA STS-DA1-2009E <Cat.No.120828> PACKAGING - TAPE & REEL Nxxxxxxx 管理番号 No. STS-DA7-0006C シリカゲルとともにリールをアルミ防湿袋に入れ、熱シールにより封をします。 Reels are shipped with desiccants in heat-sealed moisture-proof bags. ラベル Label リール Reel シリカゲル Desiccants XXXX LED TYPE Nxxxxxxx ******* LOT YMxxxx-RRR QTY. PCS RoHS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN 熱シール Seal アルミ防湿袋 Moisture-proof Bag アルミ防湿袋を並べて入れ、ダンボールで仕切ります。 Moisture-proof bags are packed in cardboard boxes with corrugated partitions. ラベル Label XXXX LED TYPE Nxxxxxxx ******* RANK RRR QTY. PCS RoHS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Nichia LED * 客先型名を*******で示します。 客先型名が設定されていない場合は空白です。 ******* is the customer part number. If not provided, it will not be indicated on the label. * ロット表記方法についてはロット番号の項を 参照して下さい。 For details, see "LOT NUMBERING CODE" in this document. * ランク分けがない場合はランク表記はありません。 The label does not have the RANK field for un-ranked products. * 本製品はテーピングしたのち、輸送の衝撃から保護するためダンボールで梱包します。 Products shipped on tape and reel are packed in a moisture-proof bag. They are shipped in cardboard boxes to protect them from external forces during transportation. * 取り扱いに際して、落下させたり、強い衝撃を与えたりしますと、製品を損傷させる原因になりますので注意して下さい。 Do not drop or expose the box to external forces as it may damage the products. * ダンボールには防水加工がされておりませんので、梱包箱が水に濡れないよう注意して下さい。 Do not expose to water. The box is not water-resistant. * 輸送、運搬に際して弊社よりの梱包状態あるいは同等の梱包を行って下さい。 Using the original package material or equivalent in transit is recommended. 8 NICHIA STS-DA1-2009E <Cat.No.120828> LOT NUMBERING CODE Lot Number is presented by using the following alphanumeric code. YMxxxx - RRR Y - Year Year Y 2009 9 2010 A 2011 B 2012 C 2013 D 2014 E M - Month Month M Month M 1 1 7 7 2 2 8 8 3 3 9 9 4 4 10 A 5 5 11 B 6 6 12 C xxxx-Nichia's Product Number RRR-Ranking by Color Coordinates, Ranking by Luminous Flux, Ranking by Forward Voltage, Ranking by Color Rendering Index 9 NICHIA STS-DA1-2009E <Cat.No.120828> DERATING CHARACTERISTICS 管理番号 No. 周囲温度-許容順電流特性 カソード側はんだ接合部温度-許容順電流特性 Solder Temperature(Cathode Side) vs Allowable Forward Cu rrent RθJA =15°C/W Ambient Temperature vs Allowable Forward Current Derating1 RθJA =25°C/W RθJA =35°C/W Derating2 2000 (74, 1500) (24, 1500) 1500 許容順電流 (0, 1270) 1000 500 (100, 995) (100, 597) Allowable Forward Current(mA) 許容順電流 2000 Allowable Forward Current(mA) NVSx219B STS-DA7-1723 (94, 1500) 1500 (100, 1350) 1000 500 (100, 426) 0 0 0 20 40 60 80 100 120 0 20 40 60 80 100 周囲温度 カソード側はんだ接合部温度 Ambient Temperature(°C) Solder Temperature(Cathode Side)(°C) デューティー比-許容順電流特性 Duty Ratio vs Allowable Forward Current Duty 120 TA=25°C 許容順電流 Allowable Forward Current(mA) 10000 2000 1500 1000 100 1 10 100 デューティー比 Duty Ratio(%) 10 NICHIA STS-DA1-2009E <Cat.No.120828> OPTICAL CHARACTERISTICS * 本特性は参考です。 All characteristics shown are for reference only and are not guaranteed. 管理番号 No. 発光スペクトル Spectrum NVSL219B STS-DA7-2444 T A=25°C IFP=700mA Spectrum 1.0 相対発光強度 Relative Emission Intensity(a.u.) 0.8 0.6 0.4 0.2 0.0 400 450 500 550 600 650 700 750 800 波長 Wavelength(nm) Directivity1 指向特性 Directivity T A=25°C IFP=700mA -20° -10° 0° 10° 20° 30° -30° 40° 放射角度 Radiation Angle -40° 50° -50° -60° 60° -70° 70° 80° -80° -90° 90° 1 0.5 0 0.5 1 相対照度 Relative Illuminance(a.u.) * 本特性は演色性ランクR70 に対応しています。 The g raphs above show the characteristics for R70 LEDs of this product. 11 NICHIA STS-DA1-2009E <Cat.No.120828> OPTICAL CHARACTERISTICS NVSL219B 管理番号 No. STS-DA7-1729A * 本特性は参考です。 All characteristics shown are for reference only and are not guaranteed. 発光スペクトル Spectrum T A=25°C IFP=700mA Spectrum 1.0 相対発光強度 Relative Emission Intensity(a.u.) 0.8 0.6 0.4 0.2 0.0 400 450 500 550 600 650 700 750 800 波長 Wavelength(nm) Directivity1 指向特性 Directivity T A=25°C IFP=700mA -20° -10° 0° 10° 20° 30° -30° 40° 放射角度 Radiation Angle -40° 50° -50° -60° 60° -70° 70° 80° -80° -90° 90° 1 0.5 0 0.5 1 相対照度 Relative Illuminance(a.u.) * 本特性は演色性ランクR8000に対応しています。 The graphs above show the characteristics for R8000 LEDs of this p roduct. 12 NICHIA STS-DA1-2009E <Cat.No.120828> FORWARD CURRENT CHARACTERISTICS / TEMPERATURE CHARACTERISTICS * 本特性は参考です。 All characteristics shown are for reference only and are not guaranteed. 周囲温度-順電圧特性 Ambient Temperature vs Forward Voltage VfIf T A=25°C 10000 4.0 2000 3.5 順電圧 Forward Voltage(V) 順電流 Forward Current(mA) 順電圧-順電流特性 Forward Voltage vs Forward Current 管理番号 No. 1000 700 100 NVSL219B STS-DA7-1730 TaVf IFP=700mA 3.0 2.5 10 2.0 2.0 2.5 3.0 3.5 4.0 -60 -40 -20 順電圧 Forward Voltage(V) 順電流-相対光束特性 Forward Current vs Relative Luminous Flux 20 40 60 80 100 120 周囲温度 Ambient Temperature(°C) 周囲温度-相対光束特性 Ambient Temperature vs Relative Luminous Flux IfIv T A=25°C TaIv IFP= 700mA 1.4 3.0 相対光束 Relative Luminous Flux(a.u.) 2.5 相対光束 Relative Luminous Flux(a.u.) 0 2.0 1.5 1.0 1.2 1.0 0.8 0.5 0.6 0.0 0 500 1000 1500 順電流 Forward Current(mA) 2000 2500 -60 -40 -20 0 20 40 60 80 100 120 周囲温度 Ambient Temperature(°C) 13 NICHIA STS-DA1-2009E <Cat.No.120828> FORWARD CURRENT CHARACTERISTICS / TEMPERATURE CHARACTERISTICS NVSL219B 管理番号 No. STS-DA7-2445A * 本特性は参考です。 All characteristics shown are for reference only and are not guaranteed. 順電流-色度特性 Forward Current vs Chromaticity Coordinate Ifxy TA=25°C 0.40 20mA 0.39 y 100mA 0.38 700mA 1500mA 2000mA 0.37 0.36 0.36 0.37 0.38 0.39 0.40 x 周囲温度-色度特性 Ambient Temperature vs Chromaticity Coordinate Taxy I FP= 700mA 0.40 y 0.39 50°C 25°C 0°C 100°C 0.38 -40°C 0.37 0.36 0.36 0.37 0.38 0.39 0.40 x * 本特性は演色性ランク R70に対応しています。 The graphs above show the characteristics for R70 LEDs of this product. 14 NICHIA STS-DA1-2009E <Cat.No.120828> FORWARD CURRENT CHARACTERISTICS / TEMPERATURE CHARACTERISTICS NVSL219B 管理番号 No. STS-DA7-1731A * 本特性は参考です。 All characteristics shown are for reference only and are not guaranteed. 順電流-色度特性 Forward Current vs Chromaticity Coordinate Ifxy TA=25°C 0.41 y 0.40 0.39 1500mA 700mA 2000mA 300mA 20mA 0.38 0.37 0.39 0.40 0.41 0.42 0.43 x 周囲温度-色度特性 Ambient Temperature vs Chromaticity Coordinate Taxy I FP= 700mA 0.41 -40°C 0.40 y 0°C 25°C 0.39 50°C 100°C 0.38 0.37 0.39 0.40 0.41 0.42 0.43 x * 本特性は演色性ランクR8000に対応しています。 The graphs above show the characteristics for R8000 LEDs of this product. 15 NICHIA STS-DA1-2009E <Cat.No.120828> RELIABILITY (1) Tests and Results Reference Test Standard Resistance to Test Test Conditions Duration JEITA ED-4701 Tsld=260°C, 10sec, 2reflows, 300 301 Precondition: 30°C, 70%RH, 168hr Solderability JEITA ED-4701 Tsld=245±5°C, 5sec, (Reflow Soldering) 303 303A Lead-free Solder(Sn-3.0Ag-0.5Cu) JEITA ED-4701 -40°C(30min)~25°C(5min)~ 100 105 100°C(30min)~25°C(5min) Moisture Resistance JEITA ED-4701 25°C~65°C~-10°C, 90%RH, (Cyclic) 200 203 24hr per cycle High Temperature JEITA ED-4701 Storage 200 201 Temperature Humidity JEITA ED-4701 Storage 100 103 Low Temperature JEITA ED-4701 Storage 200 202 Soldering Heat (Reflow Soldering) Temperature Cycle Failed/Tested 0/22 #2 0/22 100cycles #1 0/22 10cycles #1 0/22 TA=100°C 1000hours #1 0/22 TA=60°C, RH=90% 1000hours #1 0/22 TA=-40°C 1000hours #1 0/22 1000hours #1 0/22 1000hours #1 0/22 500hours #1 0/22 1000hours #1 0/22 48minutes #1 0/10 #1 0/22 TA=25°C, IF=1000mA Operating Life Test board: See NOTES below High Temperature TA=100°C, IF=400mA Operating Life Test board: See NOTES below Temperature Humidity 60°C, RH=90%, IF=700mA Operating Life Test board: See NOTES below Low Temperature TA=-40°C, IF=700mA Operating Life Test board: See NOTES below Electrostatic Discharges # Units #1 Room Temperature Vibration Failure Criteria JEITA ED-4701 200m/s2, 100~2000~100Hz, 400 403 4cycles, 4min, each X, Y, Z JEITA ED-4701 HBM, 2kV, 1.5kΩ, 100pF, 3pulses, 300 304 alternately positive or negative NOTES: 1) Test board: FR4 board thickness=1.6mm, copper layer thickness=0.07mm, RθJA≈35°C/W 2) Measurements are performed after allowing the LEDs to return to room temperature. (2) Failure Criteria Criteria # #1 #2 Items Conditions Failure Criteria Forward Voltage(VF) IF=700mA >Initial value×1.1 Luminous Flux(ΦV) IF=700mA <Initial value×0.7 Solderability - Less than 95% solder coverage 16 NICHIA STS-DA1-2009E <Cat.No.120828> CAUTIONS (1) Storage Conditions Storage Temperature Humidity Time Before Opening Aluminum Bag ≤30°C ≤90%RH Within 1 Year from Delivery Date After Opening Aluminum Bag ≤30°C ≤70%RH ≤168hours 65±5°C - ≥24hours Baking ● Product complies with JEDEC MSL 3 or equivalent. See IPC/JEDEC STD-020 for moisture-sensitivity details. ● Absorbed moisture in LED packages can vaporize and expand during soldering, which can cause interface delamination and result in optical performance degradation. Products are packed in moisture-proof aluminum bags to minimize moisture absorption during transportation and storage. Included silica gel desiccants change from blue to red if moisture had penetrated bags. ● After opening the moisture-proof aluminum bag, the products should go through the soldering process within the range of the conditions stated above. Unused remaining LEDs should be stored with silica gel desiccants in a hermetically sealed container, preferably the original moisture-proof bags for storage. ● After the “Period After Opening” storage time has been exceeded or silica gel desiccants are no longer blue, the products should be baked. Baking should only be done once. ● Although the leads or electrode pads (anode and cathode) of the product are plated with gold, prolonged exposure to a corrosive environment might cause the gold plated the leads or electrode pads to tarnish, and thus leading to difficulties in soldering. If unused LEDs remain, they must be stored in a hermetically sealed container. Nichia recommends using the original moisture-proof bag for storage. ● Do not use sulfur-containing materials in commercial products. Some materials, such as seals and adhesives, may contain sulfur. The contaminated plating of LEDs might cause an open circuit. Silicone rubber is recommended as a material for seals. Bear in mind, the use of silicones may lead to silicone contamination of electrical contacts inside the products, caused by low molecular weight volatile siloxane. ● To prevent water condensation, please avoid large temperature and humidity fluctuations for the storage conditions. (2) Directions for Use ● When designing a circuit, the current through each LED must not exceed the Absolute Maximum Rating. Operating at a constant current per LED is recommended. In case of operating at a constant voltage, Circuit B is recommended. If the LEDs are operated with constant voltage using Circuit A, the current through the LEDs may vary due to the variation in Forward Voltage characteristics of the LEDs. (A) (B) ... ... ● LEDs should be operated in forward bias. Driving circuits must not subject LEDs to either forward or reverse voltage while off. Continuous reverse voltage can cause migration and LED damage. ● It is recommended to operate the LEDs at a current greater than 10% of the sorting current to stabilize the LED characteristics. ● For outdoor use, necessary measures should be taken to prevent water, moisture and salt air damage. (3) Handling Precautions ● Do not handle LEDs with bare hands, it may contaminate the LED surface and affect optical characteristics. In the worst case, catastrophic failure from excess pressure through bump-bond breaks and package damage may result. ● When handling the product with tweezers, be careful not to apply excessive force to the resin. Otherwise, The resin can be cut, chipped, delaminate or deformed, causing bump-bond breaks and catastrophic failures. ● Dropping the product may cause damage. ● Do not stack assembled PCBs together. Failure to comply can cause the resin portion of the product to be cut, chipped, delaminated and/or deformed. It may cause bump to break, leading to catastrophic failures. 17 NICHIA STS-DA1-2009E <Cat.No.120828> (4) Design Consideration ● PCB warpage after mounting the products onto a PCB can cause the package to break. The LED should be placed in a way to minimize the stress on the LEDs due to PCB bow and twist. ● The position and orientation of the LEDs affect how much mechanical stress is exerted on the LEDs placed near the score lines. The LED should be placed in a way to minimize the stress on the LEDs due to board flexing. ● Board separation must be performed using special jigs, not using hands. ● If an aluminum PCB is used, customer is advised to verity the PCB with the products before use. Thermal stress during use can cause the solder joints to crack. (5) Electrostatic Discharge (ESD) ● The products are sensitive to static electricity or surge voltage. ESD can damage a die and its reliability. When handling the products, the following measures against electrostatic discharge are strongly recommended: Eliminating the charge Grounded wrist strap, ESD footwear, clothes, and floors Grounded workstation equipment and tools ESD table/shelf mat made of conductive materials ● Proper grounding is required for all devices, equipment, and machinery used in product assembly. Surge protection should be considered when designing of commercial products. ● If tools or equipment contain insulating materials such as glass or plastic, the following measures against electrostatic discharge are strongly recommended: Dissipating static charge with conductive materials Preventing charge generation with moisture Neutralizing the charge with ionizers ● The customer is advised to check if the LEDs are damaged by ESD when performing the characteristics inspection of the LEDs in the application. Damage can be detected with a forward voltage measurement or a light-up test at low current (≤1mA). ● ESD damaged LEDs may have current flow at a low voltage or no longer illuminate at a low current. Failure Criteria: VF<2.0V at IF=0.5mA (6) Thermal Management ● Proper thermal management is an important when designing products with LEDs. LED die temperature is affected by PCB thermal resistance and LED spacing on the board. Please design products in a way that the LED die temperature does not exceed the maximum Junction Temperature (TJ). ● Drive current should be determined for the surrounding ambient temperature (TA) to dissipate the heat from the product. ● The following equations can be used to calculate the junction temperature of the products. 1) TJ=TA+RθJA･W 2) TJ=TS+RθJS･W *TJ=LED junction temperature: °C TA=Ambient temperature: °C TS=Soldering temperature (cathode side): °C RθJA=Thermal resistance from junction to ambient: °C/W RθJS=Thermal resistance from junction to TS measuring point: °C/W W=Input power(IF×VF): W Ts Point 18 NICHIA STS-DA1-2009E <Cat.No.120828> (7) Cleaning ● If required, isopropyl alcohol (IPA) should be used. Other solvents may cause premature failure to the LEDs due to the damage to the resin portion. The effects of such solvents should be verified prior to use. In addition, the use of CFCs such as Freon is heavily regulated. ● Ultrasonic cleaning is not recommended since it may have adverse effects on the LEDs depending on the ultrasonic power and how LED is assembled. If ultrasonic cleaning must be used, the customer is advised to make sure the LEDs will not be damaged prior to cleaning. (8) Eye Safety ● In 2006, the International Electrical Commission (IEC) published IEC 62471:2006 Photobiological safety of lamps and lamp systems, which added LEDs in its scope. On the other hand, the IEC 60825-1:2007 laser safety standard removed LEDs from its scope. However, please be advised that some countries and regions have adopted standards based on the IEC laser safety standard IEC 60825-1:20112001, which still includes LEDs in its scope. Most of Nichia's LEDs can be classified as belonging into either the Exempt Group or Risk Group 1. High-power LEDs, that emit light containing blue wavelengths, may be classified as Risk Group 2. Please proceed with caution when viewing directly any LEDs driven at high current, or viewing LEDs with optical instruments which may greatly increase the damages to your eyes. ● Viewing a flashing light may cause eye discomfort. When incorporating the LED into your product, please be careful to avoid adverse effects on the human body caused by light stimulation. (9) Others ● The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment, communications equipment, measurement instruments and household appliances). Consult Nichia's sales staff in advance for information on the applications in which exceptional quality and reliability are required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control system, automobiles, traffic control equipment, life support systems and safety devices). ● The customer shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent from Nichia. When defective LEDs are found, the customer shall inform Nichia directly before disassembling or analysis. ● Both the customers and Nichia will agree on official specifications of supplied products before a customer's volume production. ● Specifications and appearance subject to change for improvement without notice. 19