HMC581LP6 / 581LP6E v00.0806 MIXERS - DOWNCONVERTERS - SMT 8 HIGH IP3 RFIC DUAL DOWNCONVERTER, 800 - 960 MHz Typical Applications Features The HMC581LP6 / HMC581LP6E is ideal for Wireless Infrastructure Applications: +26 dBm Input IP3 • GSM, GPRS & EDGE 9 dB Conversion Gain • CDMA & W-CDMA 13 dB Noise Figure • Cellular / 3G Infrastructure Single Positive Supply: +5V @ 260 mA Functional Diagram General Description Low Single Input LO Drive: 0 dBm The HMC581LP6 & HMC581LP6E are high linearity Dual Down Converter Receiver ICs that operate from 800 - 960 MHz and deliver a +26 dBm input third order intercept point for UMTS & GSM applications. The passive mixer outputs and high dynamic range IF amplifier inputs are positioned so that an external IF filter can be placed in series between them. The converter provides a gain of 9 dB and typical single side band noise figure of 13 dB. The IC operates from a single +5V supply consuming 260 mA of current while requiring only 0 dBm LO drive. The design requires no external baluns, no external matching and supports IF frequencies between 50 and 300 MHz. Electrical Specifi cations, TA = +25° C, LO = 0 dBm, Vdd = +5V, IF = 105 MHz* Parameter Min. Typ. Max. Frequency Range, RF 800 - 960 Frequency Range, LO 700 - 1160 MHz Frequency Range, IF 50 - 300 MHz Conversion Gain 7 9 MHz dB Noise Figure (SSB) 13 dB LO to RF Isolation 4 dB LO to IF Isolation 10 dB RF to IF Isolation 15 dB 26 dBm 1 dB Compression (Input) 9.5 dBm Branch Isolation 40 dB -4 to +4 dBm 256 mA IP3 (Input) 23 LO Drive Input Level (Typical) Supply Current (Idd for LO & IF) (IF bias resistor= 4.7 Ohms) * Unless otherwise noted all measurements with low side LO & IF = 105 MHz. 8 - 184 Units For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC581LP6 / 581LP6E v00.0806 HIGH IP3 RFIC DUAL DOWNCONVERTER, 800 - 960 MHz Isolation @ LO = 0 dBm 20 20 15 10 10 5 +25C +85C -40C 0 -5 -10 0.7 RF TO IF LO TO RF LO TO IF 8 0 -10 -20 -30 0.8 0.9 1 -40 0.7 1.1 0.8 RF FREQUENCY (GHz) Conversion Gain vs. LO Drive, IF = 105 MHz 1.1 0 15 -5 RETURN LOSS (dB) CONVERSION GAIN (dB) 1 Return Loss @ LO = 0 dBm 20 10 5 0 -4dBm -2dBm 0dBm +2dBm +4dBm -5 -10 0.7 0.9 RF FREQUENCY (GHz) -10 -15 RF LO -20 -25 0.8 0.9 1 1.1 0 1 RF FREQUENCY (GHz) 2 3 FREQUENCY (GHz) P1dB vs. Temperature @ LO = 0 dBm, IF = 200 MHz IF Bandwidth, LO = 0 dBm 25 MIXERS - DOWNCONVERTERS - SMT ISOLATION (dB) CONVERSION GAIN (dB) Conversion Gain vs. Temperature @ LO = 0 dBm, IF = 200 MHz 20 OUTPUT P1dB 15 20 10 RESPONSE (dB) P1dB (dBm) 15 10 5 0 OUTPUT P1dB, +85C OUTPUT P1dB, +25C OUTPUT P1dB, -40C INPUT P1dB, +25C INPUT P1dB, -40C INPUT P1dB, +85C INPUT P1dB -5 -10 0.7 0.8 0.9 1 5 CONVERSION GAIN RETURN LOSS 0 -5 -10 -15 1.1 RF FREQUENCY (GHz) -20 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 IF FREQUENCY (GHz) * Unless otherwise noted all measurements with low side LO & IF = 105 MHz. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 8 - 185 HMC581LP6 / 581LP6E v00.0806 HIGH IP3 RFIC DUAL DOWNCONVERTER, 800 - 960 MHz Input & Output IP3 vs. Temperature @ LO = 0 dBm, IF = 200 MHz Input & Output IP3 vs LO Drive, IF = 200 MHz 40 40 35 35 IP3 (dBm) IP3 (dBm) OUTPUT IP3 25 20 INPUT IP3 IIP3, +25C IIP3, +85C IIP3, -40C OIP3, +25C OIP3, +85C OIP3, -40C 15 10 0.7 0.8 0.9 1 25 IIP3 20 15 IIP3, -2dBm IIP3, 0dBm IIP3, +2dBm OIP3, -2dBm OIP3, 0dBm OIP3, +2dBm 10 5 0 0.7 1.1 0.8 RF FREQUENCY (GHz) 1 20 65 16 NOISE FIGURE (dB) OUTPUT IP2 60 55 INPUT IP2 IIP2, -2dBm IIP2, 0dBm IIP2, +2dBm OIP2, -2dBm OIP2, 0dBm OIP2,+2dBm 50 45 12 8 LO=700MHz LO=800MHz LO=1000MHz LO=1100MHz LO=1200MHz 4 0 0.8 0.9 1 1.1 50 100 RF FREQUENCY (GHz) 150 200 250 300 IF FREQUENCY (MHz) Branch Isolation RF1, IF2 @ LO = 0 dBm BRANCH ISOLATION (dB) -36 -40 -44 -48 -52 0.7 0.8 0.9 1 1.1 RF FREQUENCY (GHz) * Unless otherwise noted all measurements with low side LO & IF = 105 MHz. 8 - 186 1.1 Noise Figure vs. IF Frequency 70 40 0.7 0.9 RF FREQUENCY (GHz) Input & Output IP2 vs. LO Drive, IF = 200 MHz IP2 (dBm) MIXERS - DOWNCONVERTERS - SMT 8 OIP3 30 30 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 350 400 HMC581LP6 / 581LP6E v00.0806 HIGH IP3 RFIC DUAL DOWNCONVERTER, 800 - 960 MHz Conversion Gain vs. LO Drive, IF = 150 MHz 20 15 15 10 5 -4dBm -2dBm 0dBm 2dBm +4dBm 0 -5 -10 0.7 0.8 0.9 1 1.1 8 10 5 -4dBm -2dBm 0dBm 2dBm +4dBm 0 -5 -10 0.7 0.8 0.9 Conversion Gain vs. LO Drive, IF = 200 MHz 1.1 MxN Spurious @ IF Port 20 nLO 15 CONVERSION GAIN (dB) 1 RF FREQUENCY (GHz) RF FREQUENCY (GHz) 10 5 -4dBm -2dBm 0dBm 2dBm +4dBm 0 mRF 0 1 2 3 4 0 xx 2 36 32 53 1 19 0 26 58 62 2 75 65 50 54 89 3 108 93 88 78 89 4 123 123 117 103 89 RF Freq. = 0.8 GHz @ -10 dBm LO Freq. = 0.7 GHz @ 0 dBm All values in dBc below IF power level (1RF - 1LO). -5 -10 0.7 0.8 0.9 1 1.1 RF FREQUENCY (GHz) Typical Supply Current vs. Vdd Harmonics of LO Vdd (LO + IF) Idd (mA) +4.5 190 LO Freq. (GHz) 1 +5.0 260 0.6 15 +5.5 340 0.7 7 0.8 4 23 Downconverter will operate over full voltage range shown above. MIXERS - DOWNCONVERTERS - SMT 20 CONVERSION GAIN (dB) CONVERSION GAIN (dB) Conversion Gain vs. LO Drive IF = 70 MHz nLO Spur @ RF Port 2 3 4 16 14 26 22 15 37 19 46 0.9 3 17 25 38 1 2 17 23 25 1.1 1 20 12 24 LO = 0 dBm All values in dBc below input LO level measured at RF port. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 8 - 187 HMC581LP6 / 581LP6E v00.0806 HIGH IP3 RFIC DUAL DOWNCONVERTER, 800 - 960 MHz Absolute Maximum Ratings MIXERS - DOWNCONVERTERS - SMT 8 RF / IF Input (Vdd= +5V) +13 dBm LO Drive (Vdd= +5V) +15 dBm Vdd (LO or IF) +7 Vdc Channel Temperature 150°C Continuous Pdiss (T = 85°C) (derate 25.5 mW/°C above 85°C) 1.64 W Thermal Resistance (channel to ground paddle) 39.6 °C/W Storage Temperature -65 to +150°C Operating Temperature -40 to +85°C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC581LP6 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC581LP6E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] H581 XXXX [2] H581 XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX 8 - 188 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC581LP6 / 581LP6E v00.0806 HIGH IP3 RFIC DUAL DOWNCONVERTER, 800 - 960 MHz Pin Descriptions Function Description 1, 7 RF1, RF2 These pins are DC coupled and matched to 50 Ohms. 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28 GND Backside of package has exposed metal ground slug that must also be connected to ground. 3 Vdd Power supply for the second stage LO amplifier. One external bypass capacitor (1,000 pF) is required. 61 mA typical, 73 mA maximum. 5, 15, 19 N/C No connection. These pins may be connected to RF ground. Performance will not be affected. 9, 27 MIX IF2, MIX IF1 IF output from the mixers. This pin is DC coupled to the mixer. A low pass filter and blocking capacitor are required between mixer IF port and IF amplifier. (See application circuit). 11, 25 AMP IF2, AMP IF1 Inputs to the IF amplifiers. A low pass filter and blocking capacitor are required between mixer IF port and IF amplifier. (See application circuit). 13, 23 IF2, IF1 Outputs of the IF amplifiers and bias ports for the IF amplifiers. A pull up inductor, resistor, and bypass capacitors are required. (See application circuit). IF1 = 71 mA typical, 85 mA maximum. IF2 = 71 mA typical, 85 mA maximum. 17 LO This pin is AC coupled and matched to 50 Ohms. Vdd LO Bias voltage for the first stage of the LO amplifier. A pull up inductor, resistor, and bypass capacitors are required. (See application circuit). 53 mA typical, 64 mA maximum. 21 Interface Schematic For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 8 MIXERS - DOWNCONVERTERS - SMT Pin Number 8 - 189 HMC581LP6 / 581LP6E v00.0806 HIGH IP3 RFIC DUAL DOWNCONVERTER, 800 - 960 MHz Evaluation PCB MIXERS - DOWNCONVERTERS - SMT 8 List of Materials for Evaluation PCB 115316 [1] Item Description J1 - J5 PCB Mount SMA RF Connector J6 - J9 DC Pins C1, C4 - C10 1000 pF Chip Capacitor, 0402 Pkg. C2, C3 7 pF Chip Capacitor, 0402 Pkg. C11, C12, C13 100 pF Chip Capacitor, 0402 Pkg. L1, L2 220 nH Chip Inductor, 0603 Pkg. L3 22 nH Chip Inductor, 0603 Pkg. L4, L5 27 nH Chip Inductor, 0603 Pkg. R1, R2 4.7 Ohm Resistor, 0603 Pkg. R3 22 Ohm Resistor, 0603 Pkg. U1 HMC581LP6 / HMC581LP6E PCB [2] 106955-2 Evaluation Board The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 8 - 190 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC581LP6 / 581LP6E v00.0806 HIGH IP3 RFIC DUAL DOWNCONVERTER, 800 - 960 MHz Application Circuit Recommended Components Values (IF = DC - 300 MHz) C1, C4 - C10 1000 pF C2, C3 7 pF C11, C12, C13 100 pF L1, L2 220 nH L3 22 nH L4, L5 27 nH R1, R2 4.7 Ohm R3 22 Ohm MIXERS - DOWNCONVERTERS - SMT 8 Note: L4, C3 and L5, C2 form low pass filters, these values may be changed for optimization of LO to IF isolation, depending on application frequency. C4 and C5 are DC blocks. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 8 - 191