ACTS08MS Radiation Hardened Quad 2-Input AND Gate April 1995 Features Pinouts • 1.25 Micron Radiation Hardened SOS CMOS 14 LEAD CERAMIC DUAL-IN-LINE MIL-STD-1835 DESIGNATOR CDIP2-T14, LEAD FINISH C TOP VIEW • Total Dose 300K RAD (Si) • Single Event Upset (SEU) Immunity <1 x 10-10 Errors/Bit-Day (Typ) A1 1 14 VCC B1 2 13 B4 Y1 3 12 A4 • Latch-Up Free Under Any Conditions A2 4 11 Y4 • Military Temperature Range: -55oC to +125oC B2 5 10 B3 • Significant Power Reduction Compared to ALSTTL Logic Y2 6 9 A3 GND 7 8 Y3 2 • SEU LET Threshold >80 MEV-cm /mg 11 • Dose Rate Upset >10 RAD (Si)/s, 20ns Pulse • DC Operating Voltage Range: 4.5V to 5.5V • Input Logic Levels - VIL = 0.8V Max 14 LEAD CERAMIC FLAT PACK MIL-STD-1835 DESIGNATOR CDFP3-F14, LEAD FINISH C TOP VIEW - VIH = VCC/2 Min • Input Current ≤1µA at VOL, VOH Description The Intersil ACTS08MS is a radiation hardened quad 2-Input AND Gate. A high on both inputs forces the output to a high logic level. The ACTS08MS utilizes advanced CMOS/SOS technology to achieve high-speed operation. This device is a member of a radiation hardened, high-speed, CMOS/SOS Logic Family. A1 1 14 VCC B1 2 13 B4 Y1 3 12 A4 A2 4 11 Y4 B2 5 10 B3 Y2 6 9 A3 GND 7 8 Y3 Ordering Information PART NUMBER TEMPERATURE RANGE ACTS08DMSR -55oC ACTS08KMSR -55oC SCREENING LEVEL PACKAGE to +125oC Intersil Class S Equivalent 14 Lead SBDIP to +125oC Intersil Class S Equivalent 14 Lead Ceramic Flatpack ACTS08D/Sample +25oC Sample 14 Lead SBDIP ACTS08K/Sample +25oC Sample 14 Lead Ceramic Flatpack ACTS08HMSR +25oC Die Die Functional Diagram Truth Table INPUTS (1, 4, 9, 12) An OUTPUT An Bn Yn L L L L H L H L L H H H (3, 6, 8, 11) Yn (2, 5, 10, 13) Bn NOTE: L = Logic Level Low, H = Logic Level High CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999 1 518851 File Number 3994 Spec Number Specifications ACTS08MS Absolute Maximum Ratings Reliability Information Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +6.0V Input Voltage Range . . . . . . . . . . . . . . . . . . . . . .-0.5V to VCC +0.5V DC Input Current, Any One Input . . . . . . . . . . . . . . . . . . . . . . . .±10mA DC Drain Current, Any One Output. . . . . . . . . . . . . . . . . . . . . . .±50mA Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +265oC Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1 (All voltages reference to VSS) Thermal Impedance θJA θJC DIP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74oC/W 24oC/W Flatpack . . . . . . . . . . . . . . . . . . . . . . . . . . 116oC/W 30oC/W Maximum Package Power Dissipation at +125oC DIP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.7W Flatpack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.4W Maximum Device Power Dissipation. . . . . . . . . . . . . . . . . . .(TBD)W Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Gates CAUTION: As with all semiconductors, stress listed under “Absolute Maximum Ratings” may be applied to devices (one at a time) without resulting in permanent damage. This is a stress rating only. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. The conditions listed under “Electrical Performance Characteristics” are the only conditions recommended for satisfactory device operation. Operating Conditions Input Low Voltage (VIL). . . . . . . . . . . . . . . . . . . . . . . . . 0.0V to 0.8V Input High Voltage (VIH) . . . . . . . . . . . . . . . . . . . . . VCC to VCC/2V Supply Voltage (VCC). . . . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V Input Rise and Fall Times at 4.5V VCC (TR, TF) . . . . . . 10ns/ V Max Operating Temperature Range (TA) . . . . . . . . . . . . -55oC to +125oC TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS PARAMETER Supply Current Delta ICC (NOTE 1) CONDITIONS SYMBOL ICC GROUP A SUBGROUPS TEMPERATURE MIN MAX UNITS 1 +25oC - 5 µA - 100 µA - 1.6 mA -12 - mA -8 - mA 12 - mA 8 - mA VCC = 5.5V, VIN = VCC or GND 2, 3 DICC VCC = 5.5V VIN = VCC or GND 1 Input = 3.4V 1, 2, 3 Output Current (Source) IOH VCC = VIH = 4.5V, VOUT = VCC -0.4V, VIL = 0V (Note 2) 1 Output Current (Sink) IOL Output Voltage High VOH Output Voltage Low Input Leakage Current Noise Immunity Functional Test VOL IIN FN 2, 3 VCC = VIH = 4.5V, VOUT = 0.4V, VIL = 0V (Note 2) LIMITS +125oC, +25oC, +125oC, -55oC +25oC +125oC, -55oC +25oC 1 2, 3 -55oC +125oC, -55oC VCC = 5.5V, VIH = 2.75V, IOH = -50µA, VIL = 0.80V 1, 2, 3 +25oC, +125oC, -55oC VCC -0.1 - V VCC = 4.5V, VIH = 2.25V, IOH = -50µA, VIL = 0.8V 1, 2, 3 +25oC, +125oC, -55oC VCC -0.1 - V VCC = 5.5V, VIH = 2.75V, IOL = 50µA, VIL = 0.80V 1, 2, 3 +25oC, +125oC, -55oC - 0.1 V VCC = 4.5V, VIH = 2.25V, IOL = 50µA, VIL = 0.80V 1, 2, 3 +25oC, +125oC, -55oC - 0.1 V 1 +25oC - ±0.5 µA - ±1.0 µA - - V VCC = 5.5V, VIN = VCC or GND VCC = 4.5V, VIH = 2.25V, VIL = 0.8V (Note 3) 2, 3 7, 8A, 8B +125oC, +25oC, -55oC +125oC, -55oC NOTE: 1. All voltages reference to device GND. 2. Force/measure functions may be interchanged. 3. Per functional tests, VO ≥4.0V is recognized as a logic “1”, and VO ≤0.5V is recognized as a logic “0”. Spec Number 2 518851 Specifications ACTS08MS TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS PARAMETER (NOTES 1, 2) CONDITIONS SYMBOL Propagation Delay Input to Output TPHL GROUP A SUBGROUPS TEMPERATURE MIN MAX UNITS 9 +25oC 2 13 ns VCC = 4.5V, VIH = 3.0V, VIL = 0V TPLH 10, 11 VCC = 4.5V, VIH = 3.0V, VIL = 0V LIMITS +125oC, -55oC 2 15 ns 9 +25oC 2 14 ns 10, 11 +125oC, -55oC 2 15 ns NOTES: 1. All voltages referenced to device GND. 2. Measurements made with RL = 500Ω, CL = 50pF, Input TR = TF = 3ns. TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS LIMITS PARAMETER SYMBOL Capacitance Power Dissipation CPD Input Capacitance CIN CONDITIONS NOTE VCC = 5.0V, VIH = 5.0V, VIL = 0V, f = 1MHz VCC = 5.0V, VIH = 5.0V, VIL = 0V, f = 1MHz TEMP o MIN TYP MAX UNITS 1 +25 C - TBD - pF 1 +125oC - TBD - pF 1 +25oC - - 10 pF 1 +125oC - - 10 pF NOTE: 1. The parameters listed in Table 3 are controlled via design or process parameters. Min and Max Limits are guaranteed but not directly tested. These parameters are characterized upon initial design release and upon design changes which affect these characteristics. TABLE 4. DC POST RADIATION ELECTRICAL PERFORMANCE CHARACTERISTICS PARAMETER Supply Current SYMBOL ICC RAD LIMITS (NOTES 1, 2) CONDITIONS TEMPERATURE MIN MAX UNITS VCC = 5.5V, VIN = VCC or GND +25oC - 100 µA - 1.6 mA Delta ICC ICC VCC - 5.5V, VIN = VCC or GND 1 Input = 3.4V +25oC Output Current (Source) IOH VCC = VIH = 4.5V, VIL = 0, VOUT = VCC -0.4V +25oC -8 - mA Output Current (Sink) IOL VCC = VIH = 4.5V, VIL = 0, VOUT = 0.4V +25oC 8 - mA Output Voltage High VOH VCC = 5.5V, VIH = 2.75V, VIL = 0.80V, IOH = -50µA +25oC VCC -0.1 - V VCC = 4.5V, VIH = 2.25V, VIL = 0.80V, IOH = -50µA +25oC VCC -0.1 - V VCC = 5.5V, VIH = 2.75V, VIL = 0.80V, IOH = 50µA +25oC - 0.1 V VCC = 4.5V, VIH = 2.25V, VIL = 0.80V, IOH = 50µA +25oC - 0.1 V VCC = 5.5V, VIN = VCC or GND +25oC - ±1 µA VCC = 4.5V, VIH = 2.25V, VIL = 0.80V (Note 2) +25oC - - V VCC = 4.5V, VIH = 3.0V, VIL = 0V +25oC 2 15 ns Output Voltage Low Input Leakage Current Noise Immunity Functional Test Propagation Delay Input to Output VOL IIN FN TPHL, TPLH NOTES: 1. All voltages referenced to device GND. 2. For functional tests, VO ≥4.0V is recognized as a logic “1”, and VO ≤0.5V is recognized as a logic “0”. Spec Number 3 518851 Specifications ACTS08MS TABLE 5. DELTA PARAMETERS (+25oC) PARAMETER SYMBOL (NOTE 1) DELTA LIMIT UNITS Supply Current ICC ±1.0 µA Output Current IOL/IOH ±15 % NOTE: 1. All delta calculations are referenced to 0 hour readings or pre-life readings. TABLE 6. APPLICABLE SUBGROUPS CONFORMANCE GROUP METHOD GROUP A SUBGROUPS Initial Test (Preburn-In) 100%/5004 1, 7, 9 Interim Test 1 (Postburn-In) 100%/5004 1, 7, 9 ICC, IOL/H Interim Test 2 (Postburn-In) 100%/5004 1, 7, 9 ICC, IOL/H PDA 100%/5004 1, 7, 9, Deltas Interim Test 3 (Postburn-In) 100%/5004 1, 7, 9 PDA 100%/5004 1, 7, 9, Deltas Final Test ICC, IOL/H ICC, IOL/H 100%/5004 2, 3, 8A, 8B, 10, 11 Sample/5005 1, 2, 3, 7, 8A, 8B, 9, 10, 11 Subgroup B-5 Sample/5005 1, 2, 3, 7, 8A, 8B, 9, 10, 11, Deltas Subgroup B-6 Sample/5005 1, 7, 9 Sample/5005 1, 7, 9 Group A (Note 1) Group B READ AND RECORD Group D Subgroups 1, 2, 3, 9, 10, 11 NOTE: 1. Alternate Group A testing may be exercised in accordance with MIL-STD-883, Method 5005. TABLE 7. TOTAL DOSE IRRADIATION TEST CONFORMANCE GROUP READ AND RECORD METHOD PRE RAD POST RAD PRE RAD POST RAD 5005 1, 7, 9 Table 4 1, 9 Table 4 (Note 1) Group E Subgroup 2 NOTE: 1. Except FN test which will be performed 100% Go/No-Go. TABLE 8. BURN-IN TEST CONNECTIONS (+125oC < TA < 139oC) OSCILLATOR OPEN GROUND 1/2 VCC = 3V ±0.5V VCC = 6V ±0.5V 50kHz 25kHz 3, 6, 8, 11 14 - - 3, 6, 8, 11 1, 2, 4, 5, 9, 10, 12, 13, 14 - - 14 1, 2, 4, 5, 9, 10, 12, 13 - STATIC BURN-IN I (Note 1) - 1, 2, 4, 5, 7, 9, 10, 12, 13 STATIC BURN-IN II (Note 1) - 7 DYNAMIC BURN-IN TEST CONNECTIONS (Note 1) - 7 3, 6, 8, 11 NOTE: 1. Each pin except VCC and GND will have a series resistor of 500Ω ±5%. TABLE 9. IRRADIATION TEST CONNECTIONS (TA = +25oC, ±5oC) FUNCTION Irradiation Circuit (Note 1) OPEN GROUND VCC = 5V ±0.5V 3, 6, 8, 11 7 1, 2, 4, 5, 9, 10, 11, 12, 13, 14 NOTE: 1. Each pin except VCC and GND will have a series resistor of 47kΩ ±5%. Group E, Subgroup 2, sample size is 4 dice/wafer, 0 failures. Spec Number 4 518851 Specifications ACTS08MS Intersil - Space Products MS Screening Wafer Lot Acceptance (All Lots) Method 5007 (Includes SEM) 100% Static Burn-In 2 Method 1015, 24 Hours at +125oC Min Radiation Verification (Each Wafer) Method 1019, 4 Samples/Wafer, 0 Rejects 100% Interim Electrical Test 2 (Note 1) 100% Nondestructive Bond Pull Method 2023 100% Dynamic Burn-In Method 1015, 240 Hours at +125oC or 180 Hours at +135oC 100% Internal Visual Inspection Method 2010 100% Interim Electrical Test 3 (Note 1) 100% Temperature Cycling Method 1010 Condition C (-65o to +150oC) 100% Final Electrical Test 100% Constant Acceleration 100% Radiographics Method 2012 (2 Views) 100% PIND Testing 100% External Visual Method 2009 100% External Visual Inspection Group A (All Tests) Method 5005 (Class S) 100% Serialization Group B (Optional) Method 5005 (Class S) (Note 2) 100% Initial Electrical Test Group D (Optional) Method 5005 (Class S) (Note 2) 100% Static Burn-In 1 Method 1015, 24 Hours at +125oC Min CSI and/or GSI (Optional) (Note 2) 100% Interim Electrical Test 1 (Note 1) Data Package Generation (Note 3) 100% Fine and Gross Seal Method 1014 NOTES: 1. Failures from interim electrical tests 1 and 2 are combined for determining PDA (PDA = 5% for subgroups 1, 7, 9 and delta failures combined, PDA = 3% for subgroup 7 failures). Interim electrical tests 3 PDA (PDA = 5% for subgroups 1, 7, 9 and delta failures combined, PDA = 3% for subgroup 7 failures). 2. These steps are optional, and should be listed on the purchase order if required. 3. Data Package Contents: Cover Sheet (P.O. Number, Customer Number, Lot Date Code, Intersil Number, Lot Number, Quantity). Certificate of Conformance (as found on shipper). Lot Serial Number Sheet (Good Unit(s) Serial Number and Lot Number). Variables Data (All Read, Record, and delta operations). Group A Attributes Data Summary. Wafer Lot Acceptance Report (Method 5007) to include reproductions of SEM photos. NOTE: SEM photos to include percent of step coverage. X-Ray Report and Film, including penetrometer measurements. GAMMA Radiation Report with initial shipment of devices from the same wafer lot; containing a Cover Page, Disposition, RAD Dose, Lot Number, Test Package, Spec Number(s), Test Equipment, etc. Irradiation Read and Record data will be on file at Intersil. Propagation Delay Timing Diagram and Load Circuit DUT VIH VS TEST POINT RL 500Ω CL 50pF INPUT VSS TPLH TPHL VOH VS OUTPUT AC VOLTAGE LEVELS VOL PARAMETER ACTS UNITS VCC 4.50 V VIH 3.00 V VS 1.30 V VIL 0 V GND 0 V Spec Number 5 518851 ACTS08MS Die Characteristics DIE ATTACH: Material: Silver Glass or JM 7000 Polymer after 7/1/95 DIE DIMENSIONS: 88 mils x 88 mils 2.24mm x 2.24mm WORST CASE CURRENT DENSITY: < 2.0 x 105A/cm2 METALLIZATION: Type: AlSiCu Metal 1 Thickness: 6.75kÅ (Min), 8.25kÅ (Max) Metal 2 Thickness: 9kÅ (Min), 11kÅ (Max) BOND PAD SIZE: > 4.3 mils x 4.3 mils > 110µm x 110µm GLASSIVATION: Type: SiO2 Thickness: 8kÅ ±1kÅ Metallization Mask Layout ACTS08MS B1 (2) A1 (1) VCC (14) B4 (13) Y1 (3) (12) A4 A2 (4) (11) Y4 NC NC (10) B3 B2 (5) (6) (7) (8) (9) Y2 GND Y3 A3 Spec Number 6 518851 ACTS08MS Ceramic Dual-In-Line Metal Seal Packages (SBDIP) -A- D14.3 MIL-STD-1835 CDIP2-T14 (D-1, CONFIGURATION C) 14 LEAD CERAMIC DUAL-IN-LINE METAL SEAL PACKAGE LEAD FINISH c1 -D- BASE METAL E b1 M (b) M -Bbbb S C A - B S INCHES (c) SECTION A-A D S D BASE PLANE S2 Q -C- SEATING PLANE A L S1 eA A A b2 b e ccc M C A - B S D S eA/2 c aaa M C A - B S D S SYMBOL MIN MAX MIN MAX NOTES A - 0.200 - 5.08 - b 0.014 0.026 0.36 0.66 2 b1 0.014 0.023 0.36 0.58 3 b2 0.045 0.065 1.14 1.65 - b3 0.023 0.045 0.58 1.14 4 c 0.008 0.018 0.20 0.46 2 c1 0.008 0.015 0.20 0.38 3 D - 0.785 - 19.94 - E 0.220 0.310 5.59 7.87 - e 0.100 BSC 2.54 BSC - eA 0.300 BSC 7.62 BSC - eA/2 NOTES: 1. Index area: A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown. The manufacturer’s identification shall not be used as a pin one identification mark. MILLIMETERS 0.150 BSC 3.81 BSC - L 0.125 0.200 3.18 5.08 - Q 0.015 0.060 0.38 1.52 5 S1 0.005 - 0.13 - 6 S2 0.005 - 0.13 - 7 α 90o 105o 90o 105o - aaa - 0.015 - 0.38 - 3. Dimensions b1 and c1 apply to lead base metal only. Dimension M applies to lead plating and finish thickness. bbb - 0.030 - 0.76 - ccc - 0.010 - 0.25 - 4. Corner leads (1, N, N/2, and N/2+1) may be configured with a partial lead paddle. For this configuration dimension b3 replaces dimension b2. M - 0.0015 - 0.038 2 2. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. N 14 14 8 Rev. 0 4/94 5. Dimension Q shall be measured from the seating plane to the base plane. 6. Measure dimension S1 at all four corners. 7. Measure dimension S2 from the top of the ceramic body to the nearest metallization or lead. 8. N is the maximum number of terminal positions. 9. Braze fillets shall be concave. 10. Dimensioning and tolerancing per ANSI Y14.5M - 1982. 11. Controlling dimension: INCH. Spec Number 7 518851 ACTS08MS Ceramic Metal Seal Flatpack Packages (Flatpack) K14.A MIL-STD-1835 CDFP3-F14 (F-2A, CONFIGURATION B) 14 LEAD CERAMIC METAL SEAL FLATPACK PACKAGE A e A INCHES PIN NO. 1 ID AREA -A- D -B- S1 b MILLIMETERS SYMBOL MIN MAX MIN MAX NOTES A 0.045 0.115 1.14 2.92 - b 0.015 0.022 0.38 0.56 - b1 0.015 0.019 0.38 0.48 - c 0.004 0.009 0.10 0.23 - c1 0.004 0.006 0.10 0.15 - E1 0.004 M H A-B S 0.036 M D S H A-B S D S C Q E -D- A -C- -HL E2 E3 SEATING AND BASE PLANE c1 L E3 (c) b1 M M - 0.390 - 9.91 3 E 0.235 0.260 5.97 6.60 - E1 - 0.290 - 7.11 3 E2 0.125 - 3.18 - - E3 0.030 - 0.76 - 7 e LEAD FINISH BASE METAL D 1.27 BSC - k 0.008 0.015 0.20 0.38 2 L 0.270 0.370 6.86 9.40 - Q 0.026 0.045 0.66 1.14 8 S1 0.005 - 0.13 - 6 M - 0.0015 - 0.04 - N (b) 0.050 BSC 14 14 SECTION A-A Rev. 0 5/18/94 NOTES: 1. Index area: A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown. The manufacturer’s identification shall not be used as a pin one identification mark. Alternately, a tab (dimension k) may be used to identify pin one. 5. N is the maximum number of terminal positions. 6. Measure dimension S1 at all four corners. 7. For bottom-brazed lead packages, no organic or polymeric materials shall be molded to the bottom of the package to cover the leads. 2. If a pin one identification mark is used in addition to a tab, the limits of dimension k do not apply. 8. Dimension Q shall be measured at the point of exit (beyond the meniscus) of the lead from the body. Dimension Q minimum shall be reduced by 0.0015 inch (0.038mm) maximum when solder dip lead finish is applied. 3. This dimension allows for off-center lid, meniscus, and glass overrun. 4. Dimensions b1 and c1 apply to lead base metal only. Dimension M applies to lead plating and finish thickness. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. 9. Dimensioning and tolerancing per ANSI Y14.5M - 1982. 10. Controlling dimension: INCH. All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (321) 724-7000 FAX: (321) 724-7240 EUROPE Intersil SA Mercure Center 100, Rue de la Fusee 1130 Brussels, Belgium TEL: (32) 2.724.2111 FAX: (32) 2.724.22.05 ASIA Intersil (Taiwan) Ltd. Taiwan Limited 7F-6, No. 101 Fu Hsing North Road Taipei, Taiwan Republic of China TEL: (886) 2 2716 9310 FAX: (886) 2 2715 3029 Spec Number 8 518851