Minmax AHF-10S15 Ac/dc power module 10w fully encapsulated plastic case Datasheet

AHF-10 SERIES
AC/DC Power Module 10W
FEATURES
►Fully encapsulated Plastic Case
►PCB Mounting with Solder Pins
►Universal Input 85-264 VAC, 47-440 Hz
►Single- and Dual Output Models
►Eco Design, compliant to Energy Star specification and ErP
Directive 2009/125/EC
►Protection Class ll
►Safety Approval to cUL/UL/IEC/EN 60950-1
►Over Load and Over Voltage Protection
►3 Years Product Warranty
PRODUCT OVERVIEW
The MINMAX AHF-10 series is a range of fully encapsulated AC/DC power supply modules. The product features EMI-filter to EN55022, class B and EMS
compliance to EN 61000-4 standard. Universal input voltage 85-264VAC and International safety approvals qualifies these power modules for applications
in products with worldwide markets.The AHF-10 series provide a cost effective solution for many space critical applications in commercial and industrial
electronic equipment.
Model Selection Guide
Model
Output
Number
Voltage
Output Current
Max.
mA
2000
2000
833
666
416
±380
±300
VDC
3.3
5
12
15
24
±12
±15
AHF-10S03
AHF-10S05
AHF-10S12
AHF-10S15
AHF-10S24
AHF-10D12
AHF-10D15
Input Current
Max. capacitive
Efficiency
115VAC, 60Hz
@Max. Load
mA(typ.)
137
199
191
191
190
172
169
Load
(typ.)
@Max. Load
%
70
73
76
76
76
77
77
uF
3900
3300
2200
2200
1000
#1000
#1000
# For each output
Input Specifications
Parameter
Input Voltage Range
Input Frequency Range
Input Voltage Range
No-Load Power Consumption
Model
Min.
85
47
120
-------
All Models
115VAC
230VAC
Inrush Current (Cold Start at 25℃)
Typ.
-------------
Max.
264
440
370
0.3
10
20
Unit
VAC
Hz
VDC
W
A
A
Output Specifications
Conditions
Parameter
Output Voltage Accuracy
Line Regulation
Vin=Min. to Max.
Single Output Models
Iout=Min. to Max.
Dual Output Models
3.3 & 5.0VDC Output Models
Other Output Models
Load Regulation
Ripple & Noise (20MHz)
Minimum Load
Over Voltage Protection
Temperature Coefficient
Overshoot
Zener diode clamp
Foldback, auto-recovery
105
(long term overload condition may cause damage)
Hiccup mode, indefinite (automatic recovery)
Current Limitation
Short Circuit Protection
E-mail:[email protected]
2011/09/01 REV:12
Min.
---------------------
Tel:886-6-2923150
Page 1 of 3
Typ.
±1.0
±0.5
±0.5
±2.5
1.5
0.8
10
120
±0.01
---
Max.
±2.0
±1.0
±1.0
±5.0
1.8
1.0
----±0.02
5
Unit
%
%
%
%
%VPP of Vo
%VPP of Vo
%Inom.
% of Vo
%/℃
% Vout
---
---
%Inom.
AHF-10 SERIES
AC/DC POWER MODULE 10W
General Specifications
Parameter
I/O Isolation Voltage
I/O Isolation Resistance
Switching Frequency
Hold-up Time
MTBF (calculated)
EMC Emission
Conditions
Input to Output, 60 Seconds
500 VDC
MIL-HDBK-217F@25℃, Ground Benign
Conducted and radiated
Standard
EN61000-4-2
EN61000-4-3
EN61000-4-4
EN61000-4-5
EMC Immunity according
EN61000-6-1
EN61000-4-6
EN61000-4-8
EN61000-4-11
Protection Class II
Safety Approvals
Min.
Typ.
Max.
Unit
3000
----VACrms
100
----MΩ
--100
--KHz
--20
--ms
300,000
------Hours
EN 55011, class B, EN 55022, class B, FCC part 15, class B
Specification Requirement
Performance Criteria
Air ±8KV Cont. ±4KV
B
80~1000MHz, 10V/m 80% AM, 1KHz modulation
A
AC port ±2KV DC, SL, TL ±2KV not less than 1 min.
B
1.2/50uS(8/20uS) AC dif. ±1KV DC ±0.5KV
B
0.15~80MHz, 10Vrms (functional earth ports included)
B
80% AM, 1KHz modulation
50Hz/60Hz, 30A/m
A
30%, 10ms
B
60%, 100ms, 95%, 5000ms
C
According IEC/EN 60536
cUL/UL 60950-1,IEC/EN 60950-1
Input Fuse
All Models
2A / 250VAC
1.5A Slow – Blow Type
Built-in Fuse
External Fuse (Recommended)
Environmental Specifications
Parameter
Temperature Range (operational)
Power Derating
Storage Temperature Range
Over Temperature Protection
Cooling
Humidity (non condensing)
Ambient
+50℃ to +70℃
Conditions
-25℃
-40℃
at 90℃ (automatic recovery at 67℃)
Free-Air convection
---
+70℃
0.375W / ℃
+85℃
95 % rel. H
Notes
1
All specifications typical at Ta=+25℃, resistive load, 115VAC, 60Hz input voltage and after warm-up time rated output current unless otherwise noted.
2
Ripple & Noise measurement bandwidth is 0~20 MHz
3
These power modules require a minimum output loading to maintain specified regulation, operation under no-load conditions will not damage the power
4
Other input and output voltage may be available, please contact factory.
5
Specifications subject to change without notice
supplies however they may not meet all listed specifications.
E-mail:[email protected]
2011/09/01 REV:12
Tel:886-6-2923150
Page 2 of 3
AHF-10 SERIES
AC/DC POWER MODULE 10W
Package Specifications
Mechanical Dimensions
Pin Connections
6.0 [0.24]
10.16
[0.40]
10.16
[0.40]
19.2 [0.76]
0.7 [0.03]
Pin
Single Output
AC(N) – AC Neutral
2
AC(L) – AC Line
2
NC
5
Common
+Vout
NC: No Connection
5.0 [0.20]
Bottom View
-Vout
4
64.0 [2.52]
3
54.0 [2.13]
4
1.0 [ 0.04]
3
5
Dual Output
1
1
►All
dimensions in mm (inches)
►Tolerance: ±0.5
17.78 [0.70]
45.0 [1.77]
►Pin
(±0.02)
diameter  1.0 ±0.1 (0.04±0.004)
Physical Characteristics
Case Size
:
Case Material
:
64.0x45.0x19.2mm (2.52x1.77x0.76 Inches)
Plastic resin + Fiberglass (flammability to UL 94V-0 rated)
Weight
:
92g
Minmax Technology Co., Ltd.
18, Sin Sin Road, An-Ping Industrial District, Tainan 702, Taiwan
Tel: 886-6-2923150 Fax: 886-6-2923149 E-mail: [email protected]
2011/09/01 REV:12
Page 3 of 3
Similar pages