Totalizers electronic Large impulse counters and position displays Display LED, 6-digits, programmable N 214 Features –– Totalizer and position display –– Display 6-digits –– Set value, scaling factor, momentary signal duration and operating mode programmable –– Connection: Incremental encoder or digital sensors –– Interface RS232, RS422, RS485 Technical data - electrical ratings Voltage supply 115/230 VAC ±10 % (50/60 Hz) 24/48 VAC ±10 % (50/60 Hz) 12...30 VDC Programmable parameters Decimal point Sensor logic, scaling factor Count mode, measuring units Power consumption 7 VA, 5 W Approvals UL/cUL, CE conform Sensor supply 12...26 VDC / max. 100 mA Display LED, 7-segment display Technical data - mechanical design Number of digits 6-digits Digit height 14 mm Operating temperature 0...+50 °C Function Totalizer Difference counter A - B Parallel counter A + B Position display Storing temperature -20...+70 °C Relative humidity 80 % non-condensing E-connection Plug-in screw terminals Core cross-section 1.5 mm² 0.0001...9999.99 Protection DIN EN 60529 IP 65 face with seal Adding or subtracting A-B (difference counting) A+B total (parallel counting) Up/Down A 90° B phase evaluation Operation / keypad Membrane with softkeys Housing type Built-in housing Dimensions W x H x L 96 x 48 x 124 mm Installation depth 124 mm 3 Hz, 25 Hz, 10 kHz programmable Mounting Clip frame Measuring range -99 999...+999 999 Cutout dimensions 92 x 45 mm (+0.6) Data memory >10 years in EEPROM Materials Housing: Makrolon 6485 (PC) Keypad: Polyester Reset Button and electric Weight approx. 350 g (AC), 250 g (DC) Keylock Yes, electric (keylock) Outputs electronic Optocoupler Outputs relay Potential-free change-over contact Output holding time 0.01...9.99 s Interfaces RS232, RS422, RS485 Standard DIN EN 61010‑1 Protection class II Overvoltage category II Pollution degree 2 Emitted interference DIN EN 61000-6-3 Interference immunity DIN EN 61000-6-2 Scaling factor Count modes Counting frequency 1 www.baumerivo.com 30/10/2008 Technical data - electrical ratings Subject to modification in technic and design. Errors and omissions excepted. N 214 - Totalizer Totalizers electronic Large impulse counters and position displays Display LED, 6-digits, programmable N 214 Part number Block circuit diagram N 214. AX01 Voltage supply Voltage supply 1 24 / 48 VAC 2 115 / 230 VAC 3 24 VDC 2 4 + 3 5 Signal input A B Outputs 0 Without relay 1 Relay and optocoupler outputs 0 1 2 3 - 10 A 90° B Totalizer with start count scaling factor 7 8 Stop/Hold 9 SC- / 0 11 Output 20 21 14 SC- / 0 22 Interface RS485 T,R+ 15 Interface Without interface RS485 RS422 RS232 + Output 6 Reset T,R- Sensor supply - TxD+ 16 TxD- 17 Interface RS422 RxD+ 18 RxD- 19 TxD 16 RxD 18 Interface RS232 GND 19 Connection diagram TxD Count 5 4 0V 6 +24V Track B 7 Track A Stop 8 Reset SC- / 0 Output T,R- T,R+ RS485 9 3 2 1 Supply voltage RS232 15 14 13 12 11 10 Sensor supply Input circuit PNP- / NPN-logic Input level Programmable Input level Low 0...2 VDC Input level High 3...40 VDC Input resistance 3 kΩ Relay output Output circuit Switching voltage max. 250 VAC / 110 VDC Switching current max. 1A Switching capacity max. 150 VA / 30 W Relay responding time 5 ms Electronic output Output circuit Optocoupler not short-circuit proof Switching voltage max. 40 V Switching current max. 15 mA Dimensions 96 7 48 123.75 109 19.75 1-10 2 www.baumerivo.com 30/10/2008 TxDTxD+ RxD+ RxD- RS422 RxD max. 250V terminal - terminal / - terminal GND SC- / 0 Output Comparator inputs Inputs Subject to modification in technic and design. Errors and omissions excepted. Trigger level 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16