Series AM6TW-NZ 6 Watt | DC-DC Converter FEATURES: • • • • • Very low no load power consumption of 0.12W • Input / Output Isolation 1500, 3000 & 6000VDC • Under voltage lockout • Continuous short circuit protection Over Voltage Protection Wide 4:1 input range High efficiency up to 88% Over current Protection Models Single output Input Voltage (V) Output Voltage (V) Output Current max (mA) Max. Capacitive Load (µF) Isolation (VDC) Efficiency (%) AM6TW-2403S-NZ AM6TW-2405S-NZ AM6TW-2412S-NZ AM6TW-2415S-NZ AM6TW-2424S-NZ AM6TW-4803S-NZ AM6TW-4805S-NZ AM6TW-4812S-NZ AM6TW-4815S-NZ AM6TW-4824S-NZ 9-36 9-36 9-36 9-36 9-36 18-75 18-75 18-75 18-75 18-75 3.3 5 12 15 24 3.3 5 12 15 24 1500 1200 500 400 250 1500 1200 500 400 250 1800 1000 470 220 100 1800 1000 470 220 100 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 79 83 87 88 87 80 84 87 88 87 AM6TW-2403SH30-NZ AM6TW-2405SH30-NZ AM6TW-2412SH30-NZ AM6TW-2415SH30-NZ AM6TW-2424SH30-NZ AM6TW-4803SH30-NZ AM6TW-4805SH30-NZ AM6TW-4812SH30-NZ AM6TW-4815SH30-NZ AM6TW-4824SH30-NZ 9-36 9-36 9-36 9-36 9-36 18-75 18-75 18-75 18-75 18-75 3.3 5 12 15 24 3.3 5 12 15 24 1500 1200 500 400 250 1500 1200 500 400 250 2200 2200 680 470 330 2200 2200 680 470 330 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 79 83 88 88 87 79 83 88 88 87 AM6TW-2405SH60-NZ AM6TW-2409SH60-NZ AM6TW-2412SH60-NZ AM6TW-2415SH60-NZ AM6TW-2424SH60-NZ AM6TW-4805SH60-NZ AM6TW-4809SH60-NZ AM6TW-4812SH60-NZ AM6TW-4815SH60-NZ AM6TW-4824SH60-NZ 9-36 9-36 9-36 9-36 9-36 18-75 18-75 18-75 18-75 18-75 5 9 12 15 24 5 9 12 15 24 1200 667 500 400 250 1200 667 500 400 250 2700 1800 1000 680 470 2700 1800 1000 680 470 6000 6000 6000 6000 6000 6000 6000 6000 6000 6000 81 83 84 85 84 81 83 84 85 84 Model www.aimtec.com F 051e R6.A Tel: +1 514 620 2722 1 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM6TW-NZ 6 Watt | DC-DC Converter Models Dual output Input Voltage (V) Output Voltage (V) Output Current max (mA) Max. Capacitive Load (µF) Isolation (VDC) Efficiency (%) AM6TW-2405D-NZ AM6TW-2412D-NZ AM6TW-2415D-NZ AM6TW-4805D-NZ AM6TW-4812D-NZ AM6TW-4815D-NZ 9-36 9-36 9-36 18-75 18-75 18-75 ±5 ±12 ±15 ±5 ±12 ±15 ±600 ±250 ±200 ±600 ±250 ±200 ±680 ±330 ±220 ±680 ±330 ±220 1500 1500 1500 1500 1500 1500 83 87 88 83 87 88 AM6TW-2405DH30-NZ AM6TW-2412DH30-NZ AM6TW-2415DH30-NZ 9-36 9-36 9-36 ±5 ±12 ±15 ±600 ±250 ±200 ±680 ±330 ±220 3000 3000 3000 82 86 87 Model Input Specifications Parameters Voltage range Absolute Maximum Input Voltage (1 Sec max) Filter Reflected Input ripple current Nominal Typical 24 Vin 48 Vin 24 Vin 48 Vin 9-36 18-75 Units VDC -0.7 - 50 -0.7 - 100 VDC π (Pi) Network 20 5.5 - 6.5 14.0 – 15.5 10 24 Vin 48 Vin Input Under Voltage lockout Maximum Startup time mA p-p VDC ms Isolation Specifications Parameters Tested I/O voltage Resistance Capacitance Conditions Typical 60 sec, <1mA 1500, 3000 & 6000 > 1000 1000 13 1500 & 3000VDC isolated models 6000VDC isolated models Maximum Units VDC MOhm pF Output Specifications Parameters Voltage accuracy Balanced Load Over Voltage Protection Short Circuit protection Short circuit restart Over Current Protection Line voltage regulation Load voltage regulation Cross voltage regulation 1500VDC Isolation Cross voltage regulation 3000VDC Isolation Temperature coefficient Ripple & Noise Transient Recovery Time Transient Response Deviation www.aimtec.com F 051e R6.A Conditions Typical Dual output models ±3 ±1 Maximum Units 110 to 160 % % % of Vout Continuous Auto-recovery 1500 & 3000VDC isolated models 6000VDC isolated models 5% to 100% load 110 to 190 110 to 260 ±0.5 ±0.5 % of Iout % % 50% main load, secondary 10 to 100% load ±0.5 % 50% main load, secondary 10 to 100% load ±5 % 25% Load Step Change 25% Load Step Change Tel: +1 514 620 2722 2 of 5 ±0.03 120 300 ±5 %/°C mV p-p µS % Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM6TW-NZ 6 Watt | DC-DC Converter General Specifications Parameters Switching frequency Operating temperature Storage temperature Max Case temperature Cooling Humidity Soldering Temperature Case material Weight Dimensions (L x W x H) MTBF Conditions Typical Maximum Units 300 KHz Derating above +71 -40 to +85 °C -55 to +125 °C 100 °C Free air convection 95 % RH 1.5mm from lead for 10 sec. 300 °C 1500VDC Isolated models Aluminum Alloy 3000 & 6000VDC Isolated models Black flame-retardant heat-proof plastic 1500VDC Isolated models 14 g 3000 & 6000VDC Isolated models 13 1500VDC Isolated models 1.26 x 0.79 x 0.42 inches 32 x 20.00 x 10.80 mm 3000 & 6000VDC Isolated models 1.24 x 0.80 x 0.40 in 31.60 x 20.30 x 10.20 mm >1 000 000hrs(MIL-HDBK -217F, Ground Benign, t=+25oC) NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Environment Specifications Test Parameters Test mode Acceleration Vibration Converter operation Conditions 10-55Hz, speed 0.05Hz/s 10g, 30min, every axis tested Before and after test, body mounted (on chassis) Safety Specifications Parameters EN55022, class A, (see the recommended EMC circuits) IEC61000-4-2 (ESD, contact ±4KV) Criteria B IEC61000-4-3 (Radiated immunity, 10V/m) Criteria A IEC61000-4-4 (EFT, ±2KV) Criteria B, (see the recommended EMC circuits) IEC61000-4-5(Surge, ±2KV) Criteria B, (see the recommended EMC circuits) IEC61000-4-6(CS, 3Vrms) Criteria A IEC61000-4-29(IVDDSI, 0-70%) Criteria B Pin Out Specifications 2 3 9 11 14 16 22 23 1500VDC & 3000VDC Single Dual -V Input -V Input No pin N.C. +V Output -V Output +V Input +V Input -V Input -V Input Common -V Output +V Output Common +V Input +V Input 32.00 (1.26) 2 23 22 2.54 (0.10) 9 11 4.10 (0.16) Tel: +1 514 620 2722 3 of 5 16 14 5.08 (0.20) Built-in Stand-offs to ease PCB cleaning 10.80 (0.425) F 051e R6.A 3 Bottom View Printed Face www.aimtec.com 22.90 (0.90) 0.50 (0.02) 20.00 (0.78) Pin Dimensions 1500VDC Isolated models 15.24 (0.60) Standards All dimensions are typical: millimeters (inches) Pin Diameter: 0.50 ± 0.05 (0.02 ± 0.002) Pin Pitch Tolerance: ± 0.35 (±0.014) Case Tolerence: ± 0.5 (±0.02) Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM6TW-NZ 6 Watt | DC-DC Converter 3000VDC Isolated models 22.86 (0.90) 0.50 (0.02) 3 20.30 (0.80) 2 9 11 Bottom View 23 22 16 2.54 (0.10) 14 5.08 (0.20) Built-in Stand-offs to ease PCB cleaning All dimensions are typical: millimeters (inches) Pin Diameter: 0.50 ± 0.05 (0.02 ± 0.002) Pin Pitch Tolerance: ± 0.35 (±0.014) Case Tolerence: ± 0.5 (±0.02) Pin Out Specifications 6000VDC Single 1 11 12 13 15 23/24 +V Input No Pin -V Output +V Output No Pin -V Input 31.60 (1.24) 27.94 (1.10) 0.50 (0.02) 1 20.30 (0.80) Pin Dimensions 6000VDC Isolated models 11 12 Bottom View 24 23 2.54 (0.10) Printed Face 15 15.24 (0.60) 4.10 (0.16) 10.20 (0.40) Printed Face 15.24 (0.60) 31.60 (1.24) 13 5.08 (0.20) Built-in Stand-offs to ease PCB cleaning 10.20 (0.40) All dimensions are typical: millimeters (inches) Pin Diameter: 0.50 ± 0.05 (0.02 ± 0.002) Pin Pitch Tolerance: ± 0.35 (±0.014) Case Tolerence: ± 0.5 (±0.02) 4.10 (0.16) Derating curve External Capacitor www.aimtec.com F 051e R6.A Tel: +1 514 620 2722 4 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM6TW-NZ 6 Watt | DC-DC Converter Recommended EMC Circuit 1500VDC isolated models and 3000VDC dual output models CY1 1nF/2KV LDM 4.7µH F1 +Vin C1 MOV +Vo C3 C2 DC-DC Converter -Vin MOV C1 C2 C3 24V input S14K35 330µF/50V 1µF/50V 10µF/50V 48V input S14K60 330µF/100V 1µF/100V 10µF/100V MOV C1 C2,C3 C4 24V input S14K35 330µF/50V 2.2µF/50V 10µF/50V 48V input S14K60 330µF/100V 2.2µF/100V 10µF/100V MOV C1 C2 24V input S14K35 330µF/50V 10µF/50V 48V input S14K60 330µF/100V 10µF/100V -Vo CY2 1nF/2KV Recommended EMC Circuit 3000VDC single output models LCM 2.2mH F1 +Vin +Vo C1 MOV C2 C3 -Vin C4 DC-DC Converter -Vo Recommended EMC Circuit 6000VDC isolated models F1 +Vin +Vo C1 MOV -Vin C2 DC-DC Converter -Vo Recommended Circuit 6000VDC isolated models for class B compliance CY1 L 1 3 2 4 C1 +V output +V input DC/DC Converter CY1, CY2 C1,C2 L1 1nF/400VAC 2.2µF/50V 2.2mH Load C2 -V input -V output CY2 NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R6.A Tel: +1 514 620 2722 5 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only