SMD INFRARED EMITTING DIODES BL-LS3528A0S1IR Features: 3.5mmx2.8mm SMD, 1.9mm THICKNESS PLCC2 package, Infrared LED High Reliability Peak Wavelength at 940, 880, 850nm Water Clear, yellow Transparent, Blue Transparent available IC compatible /Low current capability. PACKAGE: 2KPCS/REEL. RoHs Compliance Applications: Free air transmission system Infrared remote control units with high power requirement Smoke detector Infrared Camera Infrared applied system Electrical-optical characteristics: (Ta=25°C) (Test Condition: IF=50mA) Chip Part Number Lens Type ∆λ Ir (Vr=5 V, uA) Forward Voltage(VF) Unit:V Radiant Power (mw/sr) Material P (nm) Typ Max Typ BL-LS3528A0S1IRAC GaAs 940 Water Clear 50 10 1.40 1.60 30 BL-LS3528A0S1IRAB GaAs 940 Blue Trans. 50 10 1.40 1.60 30 BL-LS3528A0S1IRBC GaAlAs 880 Water Clear 50 10 1.70 2.00 30 BL-LS3528A0S1IRBB GaAlAs 880 Blue Trans. 50 10 1.70 2.00 30 BL-LS3528A0S1IRCC GaAlAs 850 Water Clear 50 10 1.70 2.00 50 BL-LS3528A0S1IRCB GaAlAs 850 Blue Trans. 50 10 1.70 2.00 50 BL-LS3528A0S1IRCY GaAlAs 850 Yellow Trans. 50 10 1.70 2.00 50 Viewi ng Angle 2θ1/2 (deg) 120 Absolute maximum ratings (Ta=25°C) Parameter Rating Unit 50 160 5 mW Forward Current IF Power Dissipation Pd Reverse Voltage VR Peak Forward Current IPF (Duty 1/10 @1KHZ) Operation Temperature TOPR 250 mA -40 to +100 °C Storage Temperature TSTG -40 to +100 °C Max.260±5°C for 3 sec Max. (1.6mm from the base of the epoxy bulb) °C Lead Soldering Temperature TSOL APPROVED : XU L CHECKED :ZHANG WH DRAWN: LI FS REV NO: V.2 Page 1 of 4 WWW.BETLUX.COM EMAIL: [email protected] , [email protected] mA V SMD INFRARED EMITTING DIODES BL-LS3528A0S1IR Package configuration & Internal circuit diagram Notes: 1. All dimensions are in millimeters (inches) 2. Tolerance is ±0.25(0.01")unless otherwise noted. 3. Specifications are subject to change without notice. APPROVED : XU L CHECKED :ZHANG WH DRAWN: LI FS REV NO: V.2 Page 2 of 4 WWW.BETLUX.COM EMAIL: [email protected] , [email protected] SMD INFRARED EMITTING DIODES BL-LS3528A0S1IR Tape Specifications Smt Reflow Solding Instructions Number of reflow process shall be less than 2 times and cooling process to normai temperature is required between first and second soldering process Recommended Soldering Pattern (Units:mm) Tape Specifications (Units:mm) APPROVED : XU L CHECKED :ZHANG WH DRAWN: LI FS REV NO: V.2 Page 3 of 4 WWW.BETLUX.COM EMAIL: [email protected] , [email protected] SMD INFRARED EMITTING DIODES BL-LS3528A0S1IR Packing and weighting 2000pcs/Reel 1 Reel/Bag Maximum 10 Bags/Inner Box 3 Inner Box/Box 9 Inner Box/Box APPROVED : XU L CHECKED :ZHANG WH DRAWN: LI FS REV NO: V.2 Page 4 of 4 WWW.BETLUX.COM EMAIL: [email protected] , [email protected]