Revised October 1998 GTLP16617 17-Bit TTL/GTLP Synchronous Bus Transceiver with Buffered Clock General Description Features The GTLP16617 is a 17-bit registered synchronous bus transceiver that provides TTL to GTLP signal level translation. It allows for transparent, latched and clocked modes of data flow and provides a buffered GTLP (CLKOUT) clock output from the TTL CLKAB. The device provides a high speed interface between cards operating at TTL logic levels and a backplane operating at GTLP logic levels. High speed backplane operation is a direct result of GTLP’s reduced output swing (<1V), reduced input threshold levels and output edge rate control. The edge rate control minimizes bus settling time. GTLP is a Fairchild Semiconductor derivative of the Gunning Transceiver logic (GTL) JEDEC standard JESD8-3. ■ Bidirectional interface between GTLP and TTL logic levels Fairchild’s GTLP has internal edge-rate control and is process, voltage, and temperature (PVT) compensated. Its function is similar to BTL and GTL but with different output levels and receiver threshold. GTLP output LOW level is typically less than 0.5V, the output level HIGH is 1.5V and the receiver threshold is 1.0V. ■ Edge Rate Control to minimize noise on the GTLP port ■ Power up/down/off high impedance for live insertion. ■ External VREF pin for receiver threshold ■ CMOS technology for low power dissipation ■ 5 V tolerant inputs and outputs on the A-Port ■ Bus-hold data inputs on the A-Port eliminates the need for external pull-up resistors on unused inputs. ■ TTL compatible driver and control inputs ■ Flow through pinout optimizes PCB layout ■ Open drain on GTLP to support wired-or connection ■ A-Port source/sink −32 mA/+32 mA ■ D-type flip-flop, latch and transparent data paths ■ GTLP Buffered CLKAB signal available(CLKOUT) ■ Recommended Operating Temperature −40°C to 85°C Ordering Code: Order Number Package Number GTLP16617MEA MS56A 56-Lead Shrink Small Outline Package (SSOP), JEDEC MO-118 0.300” Wide Package Description GTLP16617MTD MTD56 56-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 6.1mm Wide Devices also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering code. © 1998 Fairchild Semiconductor Corporation DS500031.prf www.fairchildsemi.com GTLP16617 17-Bit TTL/GTLP Synchronous Bus Transceiver with Buffered Clock June 1997 GTLP16617 Pin Descriptions Pin Names Connection Diagram Description OEAB A-to-B Output Enable (Active LOW) OEBA B-to-A Output Enable (Active LOW) CEAB A-to-B Clock Enable (Active LOW) CEBA B-to-A Clock Enable (Active LOW) LEAB A-to-B Latch Enable (Transparent HIGH) LEBA B-to-A Latch Enable (Transparent HIGH) VREF GTLP Reference Voltage CLKAB A-to-B Clock CLKBA B-to-A Clock A1-A17 A-to-B Data Inputs or B-to-A 3-STATE Data Outputs B1-B17 B-to-A Data Inputs or A-to-B Open Drain Outputs CLKIN B-to-A Buffered Clock Output CLKOUT GTLP Buffered Clock Output of CLKAB Functional Description The GTLP16617 is a 17 bit registered transceiver containing D-type flip-flop, latch and transparent modes of operation for the data path and a GTLP translation of the CLKAB signal (CLKOUT). Data flow in each direction is controlled by the clock enables (CEAB and CEBA), latch enables (LEAB and LEBA), clock (CLKAB and CLKBA) and output enables (OEAB and OEBA). The clock enables (CEAB and CEBA) enable all 17 data bits. The output enables (OEAB and OEBA) control both the 17 bits of data and the CLKOUT/CLKIN buffered clock paths and the OEAB is synchronous with the CLKAB signal. The OEBA can not be synchronous since we are passing the clock through the device with data and we would need to generate the CLKBA signal elsewhere. It should also be noted that the OEAB register is controlled by CLKAB only, and is also not inhibited by the CEAB signal. For A-to-B data flow, when CEAB is LOW, the device operates on the LOW-to-HIGH transition of CLKAB for the flip-flop and on the HIGH-to-LOW transition of LEAB for the latch path. That is, if CEAB is LOW and LEAB is LOW the A data is latched regardless as to the state of CLKAB (HIGH or LOW) and if LEAB is HIGH the device is in transparent mode. When OEAB is registered LOW the outputs are active. When OEAB is registered HIGH the outputs are HIGH impedance. The data flow of B-to-A is similar except that CEBA, OEBA, LEBA and CLKBA are used. Truth Table (Note 1) Inputs Output B Mode Latched storage of A data CEAB OEAB(Note 2) LEAB CLKAB A X H X ↑ X Z (Note 3) L L L H or L X B0(Note 4) (Note 5) L L L H or L X X L H X L L X L H X H H L L L ↑ L L L L L ↑ H H Clocked storage of A data H L L X X B0(Note 5) Clock inhibit Transparent Note 1: A-to-B data flow is shown. B-to-A data flow is similar but uses OEBA, LEBA, CLKBA, CEBA. Note 2: LH edge on CLKAB is required when changing the input on OEAB pin. Note 3: OEAB met set-up time prior to CLKAB LH transition Note 4: Output level before the indicated steady state input conditions were established, provided CLKAB was HIGH prior to LEAB going LOW. Note 5: Output level before the indicated steady state input conditions were established. www.fairchildsemi.com 2 GTLP16617 Logic Diagram 3 www.fairchildsemi.com GTLP16617 Absolute Maximum Ratings(Note 6) Supply Voltage (VCC ) −0.5V to +7.0V DC Input Voltage (VI) −0.5V to +7.0V Recommended Operating Conditions (Note 8) Supply Voltage VCC DC Output Voltage (VO) Outputs 3-STATE Outputs Active (Note 7) −0.5V to +7.0V −0.5V to VCC + 0.5V 64 mA on A-Port and Control Pins −64 mA −50 mA +50 mA +34 mA B-Port Operating Temperature (TA) −50 mA VO > VCC www.fairchildsemi.com +32 mA A-Port 80 mA VO < 0V Storage Temperature (TSTG) −32 mA A-Port −40°C to +85°C Note 6: The Absolute Maximum Ratings are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum rating. The “Recommended Operating Conditions” table will define the conditions for actual device operation. DC Output Diode Current (IOK) ESD Rating 0.0V to 5.5V LOW Level Output Current (IOL) DC Input Diode Current (IIK) VI < 0V 1.35V to 1.65V HIGH Level Output Current (IOH) DC Output Sink Current into B-Port in the LOW State, IOL 4.75V to 5.25V Input Voltage (VI) DC Output Source Current from A-Port IOH 3.15V to 3.45V Bus Termination Voltage (VTT) GTLP DC Output Sink Current into A-Port IOL VCC VCCQ >2000V Note 7: IO Absolute Maximum Rating must be observed. −65°C to +150°C Note 8: Unused inputs must be held high or low. 4 Over Recommended Operating Free-Air Temperature Range, VREF = 1.0V (Unless Otherwise Noted). Symbol Test Conditions Min Typ Max Units (Note 9) VIH VIL B-Port VREF +0.1 Others 2.0 B-Port 0.0 VTT Others VREF GTLP 1.0 GTL 0.8 VCC = 3.15V, VIK II = −18 mA VREF −0.2 V 0.8 V V V −1.2 VCCQ = 4.75V VOH VOL A-Port A-Port VCC, VCCQ = Min to Max (Note 10) IOH = −100 µA VCC = 3.15V IOH = −8 mA 2.4 VCCQ = 4.75V IOH = −32 mA 2.0 V V V VCC −0.2 V VCC, VCCQ = Min to Max (Note 10) IOL = 100 µA 0.2 VCC = 3.15V IOL = 32 mA 0.5 V VCCQ = 4.75V II B-Port VCC = 3.15V VCCQ = 4.75V IOL = 34 mA 0.65 V Control Pins VCC, VCCQ = 0 or Max VI = 5.5V or 0V ±10 µA A-Port VCC = 3.45V VI = 5.5V 20 VCCQ = 5.25V VI = VCC 1 VI = 0 B-Port VCC = 3.45V VI = VCCQ 5 VCCQ = 5.25V VI = 0 −5 IOFF A-Port and Control Pins VCC = VCCQ = 0 VI or VO = 0 to 4.5V II(hold) A-Port VCC = 3.15V, VI = 0.8V 75 VCCQ = 4.75V VI = 2.0V −20 IOZH A-Port VCC = 3.45V, VO = 3.45V B-Port VCCQ = 5.25V VO = 1.5V A-Port VCC = 3.45V, VO = 0 IOZL 100 5 −20 B-Port VCCQ = 5.25V VO = 0.65V A or B VCC = 3.45V, Outputs HIGH 30 40 (VCCQ) Ports −10 VCCQ = 5.25V, Outputs LOW 30 40 VI = VCCQ or GND Outputs Disabled 30 40 VCC = 3.45V, VCCQ = 5.25V, IO = 0, Outputs HIGH 0 1 Outputs LOW 0 1 VI = VCCQ or GND Outputs Disabled 0 1 One Input at 2.7V 0 1 IO = 0, A or B Ports ∆ICC A-Port and VCC = 3.45V, (Note 11) Control Pins VCCQ = 5.25V, µA µA µA 1 ICCQ ICC (VCC) µA −30 µA µA mA mA mA A or Control Inputs at VCC or GND CIN Control Pins VI = VCCQ or 0 8 CI/O A-Port VI = VCCQ or 0 9 CI/O B-Port VI = VCCQ or 0 6 pF Note 9: All typical values are at VCC = 3.3V, VCCQ = 5.0V, and TA = 25°C. Note 10: For conditions shown as Min or Max, use the appropriate value specified under recommended operating conditions. Note 11: This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. 5 www.fairchildsemi.com GTLP16617 DC Electrical Characteristics GTLP16617 AC Operating Requirements Over recommended ranges of supply voltage and operating free-air temperature, VREF = 1.0V (unless otherwise noted). Symbol fCLOCK Max Clock Frequency tW Pulse Duration tS tH Min 175 LEAB or LEBA HIGH 3.0 CLKAB or CLKBA HIGH or LOW 3.2 A before CLKAB↑ 0.5 Max Unit MHz ns Setup Time Hold Time www.fairchildsemi.com OEAB before CLKAB↑ 1.5 B before CLKBA↑ 3.1 A before LEAB↓ 1.3 B before LEBA↓ 3.7 CEAB before CLKAB↑ 0.7 CEBA before CLKBA↑ 1.0 A after CLKAB↑ 1.5 OEAB after CLKAB↑ 1.0 B after CLKBA↑ 0.0 A after LEAB↓ 0.5 B after LEBA↓ 0.0 CEAB after CLKAB↑ 1.5 CEBA after CLKBA↑ 1.7 6 ns ns Over recommended range of supply voltage and operating free-air temperature, VREF = 1.0V (unless otherwise noted). CL = 30 pF for B-Port and CL = 50 pF for A-Port. Symbol tPLH From To (Input) (Output) A B tPHL tPLH LEAB B tPHL tPLH CLKAB B tPHL tPLH CLKAB CLKOUT tPHL tPLH OEAB tPHL (CLKAB) (Note 13) tSKEW B (Note 14) B CLKOUT tRISE Transition time, B outputs (20% to 80%) tFALL Transition time, B outputs (20% to 80%) tPLH ns 1.0 4.3 6.5 1.0 5.0 8.2 1.8 4.5 6.7 1.5 5.3 8.7 1.8 4.6 6.7 1.5 5.4 8.7 3.0 6.2 10.0 3.0 5.7 10.0 1.6 4.4 8.0 1.3 6.1 9.8 0 2 2.6 1.4 5.0 7.2 A 2.1 4.2 6.3 1.9 3.3 5.0 2.3 4.4 6.8 A CLKOUT CLKIN OEBA A or CLKIN tPHZ, tPLZ ns ns ns ns 2.6 LEBA CLKBA ns ns 5.6 tPHL tPZH, tPZL Unit 2.0 tPHL tPLH Max A tPHL tPLH Typ (Note 12) B tPHL tPLH Min 8.2 2.1 3.5 5.2 3.0 6.0 10.0 3.0 6.43 10.0 1.5 5.0 6.4 1.4 3.9 8.0 ns ns ns ns ns Note 12: All typical values are at VCC = 3.3V, VCCQ = 5.0V, and TA = 25°C. Note 13: Three-state delays are actually synchronous with CLKAB Note 14: Skew is defined as the absolute value of the difference between the actual propagation delays for the CLKOUT pin and any B output transition when measured with reference to CLKAB↑. This guarantees the relationship between B output data and CLKOUT such that data is coincident or ahead of CLKOUT. This specification is guaranteed but not tested. 7 www.fairchildsemi.com GTLP16617 AC Electrical Characteristics GTLP16617 Test Circuits and Timing Waveforms Test Circuit for B Outputs Test Circuit for A Outputs CL includes probes and jig capacitance. CL includes probes and jig capacitance. For B-Port outputs, CL = 30 pF is used for worst case edge rate. Voltage Waveforms Pulse Duration (Vm = 1.5V for A-Port and 1.0V for B-Port) Voltage Waveforms Propagation Delay and Setup and Hold Times (Vm = 1.5V for A-Port and 1.0V for B-Port) Voltage Waveforms Enable and Disable Times (A-Port) Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. All input pulses have the following characteristics: frequency = 10 MHz, tr = t f = 2 ns, Z O = 50Ω. The outputs are measured one at a time with one transition per measurement. www.fairchildsemi.com 8 GTLP16617 Physical Dimensions inches (millimeters) unless otherwise noted 56-Lead Shrink Small Outline Package, JEDEC MO-118 0.300” Wide Package Number MS56A 9 www.fairchildsemi.com GTLP16617 17-Bit TTL/GTLP Synchronous Bus Transceiver with Buffered Clock Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 56-Lead Thin Shrink Small Outline Package, JEDEC MO-153, 6.1mm Wide Package Number MTD56 LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support 1. Life support devices or systems are devices or systems device or system whose failure to perform can be reawhich, (a) are intended for surgical implant into the sonably expected to cause the failure of the life support body, or (b) support or sustain life, and (c) whose failure device or system, or to affect its safety or effectiveness. to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the www.fairchildsemi.com user. Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications.