TI1 LMR23630APQDRRRQ1 Simple switcher 36 v, 3 a synchronous step-down converter Datasheet

Sample &
Buy
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
LMR23630-Q1
SNVSAR6 – DECEMBER 2016
LMR23630-Q1 SIMPLE SWITCHER® 36 V, 3 A Synchronous Step-Down Converter
1 Features
3 Description
•
•
The LMR23630-Q1 SIMPLE SWITCHER® is an easy
to use 36 V, 3 A synchronous step down regulator.
With a wide input range from 4 V to 36 V, it is
suitable for various applications from industrial to
automotive for power conditioning from unregulated
sources. Peak current mode control is employed to
achieve simple control loop compensation and cycleby-cycle current limiting. A quiescent current of 75 μA
makes it suitable for battery powered systems.
Internal loop compensation means that the user is
free from the tedious task of loop compensation
design. This also minimizes the external components.
The device has option for constant frequency FPWM
mode to achieve small output voltage ripple at light
load. An extended family is available in 1 A
(LMR23610-Q1), 1.5 A (LMR23615-Q1) and 2.5 A
(LMR23625-Q1) load current options in pin-to-pin
compatible package which allows simple, optimum
PCB layout. A precision enable input allows
simplification of regulator control and system power
sequencing. Protection features include cycle-bycycle current limit, hiccup mode short circuit
protection and thermal shutdown due to excessive
power dissipation.
1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Qualified for Automotive Applications
AEC-Q100 Qualified With the Following Results:
- Device Temperature Grade 1: -40 °C to 125 °C
Ambient Operating Temperature Range
- Device HBM ESD Classification Level H1C
- Device CDM ESD Classification Level C4A
4 V to 36 V Input Range
3 A Continuous Output Current
Integrated Synchronous Rectification
Minimum Switch-On Time: 60 ns
Internal Compensation for Ease of Use
400 kHz Switching Frequency and Adjustable
Switching Frequency Options
PFM and Forced PWM Mode Options at Light
Load
Frequency Synchronization to External Clock
75 µA Quiescent Current at No Load for PFM
Option
Power Good Option
Soft-Start into a Pre-Biased Load
High Duty Cycle Operation Supported
Output Short-Circuit Protection with Hiccup Mode
8-Pin HSOIC and 12-Pin WSON with
PowerPAD™ Package Options
2 Applications
•
•
•
•
Automotive Battery Regulation
Industrial Power Supplies
Telecom and Datacom Systems
General Purpose Wide Vin Regulation
Device Information(1)
PART NUMBER
PACKAGE
BODY SIZE (NOM)
LMR23630AQDDARQ1
HSOIC (8)
4.9 mm x 3.9 mm
LMR23630AFQDDARQ1
HSOIC (8)
4.9 mm x 3.9 mm
LMR23630QDRRRQ1
(Preview)
WSON (12)
3 mm x 3 mm
LMR23630FQDRRRQ1
(Preview)
WSON (12)
3 mm x 3 mm
LMR23630APQDRRRQ1
(Preview)
WSON (12)
3 mm x 3 mm
(1) For detail part numbers for all available different options, see
the orderable addendum at the end of the data sheet.
Simplified Schematic
Efficiency vs Load, VIN = 12 V, PFM Option
VIN up to 36 V
100
CIN
VIN
90
BOOT
CBOOT
AGND
L
VOUT
SW
RFBT
COUT
VCC
FB
CVCC
RFBB
Efficiency (%)
EN/SYNC
80
70
60
PGND
50
VOUT = 5 V
VOUT = 3.3 V
40
0.0001
0.001
0.01
0.1
IOUT (A)
1
10
D001
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LMR23630-Q1
SNVSAR6 – DECEMBER 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Product Portfolio....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
3
4
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
4
4
4
5
6
7
8
9
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions ......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Timing Characteristics...............................................
Switching Characteristics ..........................................
Typical Characteristics ..............................................
8.4 Device Functional Modes........................................ 19
9
Application and Implementation ........................ 20
9.1 Application Information............................................ 20
9.2 Typical Applications ................................................ 20
10 Power Supply Recommendations ..................... 26
11 Layout................................................................... 26
11.1
11.2
11.3
11.4
11.5
Layout Guidelines .................................................
Compact Layout for EMI Reduction ......................
Ground Plane and Thermal Considerations..........
Feedback Resistors ..............................................
Layout Example ....................................................
26
26
27
27
28
12 Device and Documentation Support ................. 29
12.1
12.2
12.3
12.4
12.5
Detailed Description ............................................ 11
8.1 Overview ................................................................. 11
8.2 Functional Block Diagram ....................................... 11
8.3 Feature Description................................................. 12
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
29
29
29
29
29
13 Mechanical, Packaging, and Orderable
Information ........................................................... 30
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
2
DATE
REVISION
NOTES
December 2016
*
Initial release.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
LMR23630-Q1
www.ti.com
SNVSAR6 – DECEMBER 2016
5 Product Portfolio
Package
SOIC (8)
WSON (12)
(Pin 6 is RT)
WSON (12)
(Pin 6 is PGOOD)
Part Number
Fixed 400kHz
LMR23630AQDDARQ1
√
LMR23630AFQDDARQ1
√
Adjustable
Frequency
Power Good
√
LMR23630QDRRRQ1
√
LMR23630FQDRRRQ1
√
√
√
LMR23630APQDRRRQ1
FPWM
√
6 Pin Configuration and Functions
DDA Package
8-Pin SOIC
Top View
SW
1
BOOT
2
PAD
9
VCC
3
FB
4
DRR Package
12-Pin WSON
Top View
DRR Package
12-Pin WSON
Top View
8
PGND
SW
1
12
PGND
SW
1
12
PGND
7
VIN
SW
2
11
NC
SW
2
11
NC
3
10
VIN
3
10
VIN
AGND
BOOT
BOOT
6
VCC
4
9
VIN
VCC
4
9
VIN
5
EN/SYNC
FB
5
8
EN/
SYNC
FB
5
8
EN/
SYNC
RT
6
7
PGOOD
6
7
AGND
AGND
PAD
13
PAD
13
Pin Functions
PIN
NO.
I/O
(1)
DESCRIPTION
SOIC-8
WSON-12
With RT
WSON-12
With
PGOOD
SW
1
1, 2
1, 2
P
Switching output of the regulator. Internally connected to both power MOSFETs.
Connect to power inductor.
BOOT
2
3
3
P
Boot-strap capacitor connection for high-side driver. Connect a high quality 100
nF capacitor from BOOT to SW.
VCC
3
4
4
P
Internal bias supply output for bypassing. Connect a 2.2 μF/ 16 V or higher
capacitance bypass capacitor from this pin to AGND. Do not connect external
loading to this pin. Never short this pin to ground during operation.
FB
4
5
5
A
Feedback input to regulator, connect the midpoint of feedback resistor divider to
this pin.
RT
N/A
N/A
6
A
Connect a resistor RT from this pin to AGND to program switching frequency.
Leave floating for 400 kHz default switching frequency.
PGOOD
N/A
6
N/A
A
Open drain output for power-good flag. Use a 10 kΩ to 100 kΩ pull-up resistor
to logic rail or other DC voltage no higher than 12 V.
EN/SYNC
5
8
8
A
Enable input to regulator. High = On, Low = Off. Can be connected to VIN. Do
not float. Adjust the input under voltage lockout with two resistors. The internal
oscillator can be synchronized to an external clock by coupling a positive pulse
into this pin through a small coupling capacitor. See Enable/Sync for detail.
AGND
6
7
7
G
Analog ground pin. Ground reference for internal references and logic. Connect
to system ground.
VIN
7
9, 10
9, 10
P
Input supply voltage.
NAME
(1)
A = Analog, P = Power, G = Ground.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
3
LMR23630-Q1
SNVSAR6 – DECEMBER 2016
www.ti.com
Pin Functions (continued)
PIN
NO.
I/O
(1)
DESCRIPTION
SOIC-8
WSON-12
With RT
WSON-12
With
PGOOD
PGND
8
12
12
G
Power ground pin, connected internally to the low side power FET. Connect to
system ground, PAD, AGND, ground pins of CIN and COUT. Path to CIN must be
as short as possible.
PAD
9
13
13
G
Low impedance connection to AGND. Connect to PGND on PCB. Major heat
dissipation path of the die. Must be used for heat sinking to ground plane on
PCB.
N/A
11
11
N/A
NAME
NC
Not for use. Leave this pin floating.
7 Specifications
7.1 Absolute Maximum Ratings
Over the recommended operating junction temperature range of -40 °C to 125 °C (unless otherwise noted)
PARAMETER
Input Voltages
(1)
MIN
MAX
VIN to PGND
-0.3
42
EN/SYNC to AGND
-5.5
VIN + 0.3
FB to AGND
-0.3
4.5
RT to AGND
-0.3
4.5
PGOOD to AGND
-0.3
15
AGND to PGND
UNIT
V
-0.3
0.3
SW to PGND
-1
VIN + 0.3
SW to PGND less than 10 ns transients
-5
42
BOOT to SW
-0.3
5.5
VCC to AGND
-0.3
TJ
Junction temperature
-40
150
°C
Tstg
Storage temperature
-65
150
°C
Output Voltages
(1)
(2)
4.5
V
(2)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
In shutdown mode, the VCC to AGND maximum value is 5.25 V.
7.2 ESD Ratings
VALUE
V(ESD)
(1)
Electrostatic discharge
(1)
±2500
Charged-device model (CDM)
±1000
Human-body model (HBM)
UNIT
V
AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
7.3 Recommended Operating Conditions
Over the recommended operating junction temperature range of -40 °C to 125 °C (unless otherwise noted)
VIN
Input Voltage
Input Current
(1)
4
EN/SYNC
MIN
MAX
4
36
-5
36
FB
-0.3
1.2
PGOOD
-0.3
12
0
1
PGOOD pin current
(1)
UNIT
V
mA
Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits.
For guaranteed specifications, see Electrical Characteristics.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
LMR23630-Q1
www.ti.com
SNVSAR6 – DECEMBER 2016
Recommended Operating Conditions (continued)
Over the recommended operating junction temperature range of -40 °C to 125 °C (unless otherwise noted) (1)
MIN
MAX
UNIT
V
Output Voltage
VOUT
1
28
Output Current
IOUT
0
3
A
Temperature
Operating junction temperature, TJ
-40
125
°C
7.4 Thermal Information
THERMAL METRIC
(1) (2)
DDA
(8 PINS)
DRR
(12 PINS)
RθJA
Junction-to-ambient thermal resistance
42.0
41.5
ψJT
Junction-to-top characterization parameter
5.9
0.3
ψJB
Junction-to-board characterization parameter
23.4
16.5
RθJC(top)
Junction-to-case (top) thermal resistance
45.8
39.1
RθJC(bot)
Junction-to-case (bottom) thermal resistance
3.6
3.4
RθJB
Junction-to-board thermal resistance
23.4
16.3
(1)
(2)
UNIT
°C/W
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
Power rating at a specific ambient temperature TA should be determined with a maximum junction temperature (TJ) of 125 °C, which is
illustrated in Recommended Operating Conditions section.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
5
LMR23630-Q1
SNVSAR6 – DECEMBER 2016
www.ti.com
7.5 Electrical Characteristics
Limits apply over the recommended operating junction temperature (TJ) range of -40 °C to +125 °C, unless otherwise stated.
Minimum and Maximum limits are specified through test, design or statistical correlation. Typical values represent the most
likely parametric norm at TJ = 25 °C, and are provided for reference purposes only.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
36
V
POWER SUPPLY (VIN PIN)
VIN
Operation input voltage
4
VIN_UVLO
Under voltage lockout thresholds
Rising threshold
3.3
3.7
3.9
Falling threshold
2.9
3.3
3.5
4.0
ISHDN
Shutdown supply current
VEN = 0 V, VIN = 12 V, TJ = -40 °C to 125
°C
2.0
IQ
Operating quiescent current (nonswitching)
VIN = 12 V, VFB = 1.1 V, TJ = -40 °C to
125 °C, PFM mode
75
V
μA
μA
ENABLE (EN PIN)
VEN_H
Enable rising threshold Voltage
VEN_HYS
Enable hysteresis voltage
VWAKE
Wake-up threshold
IEN
Input leakage current at EN pin
1.4
1.55
1.7
0.4
V
0.4
VIN = 4 V to 36 V, VEN= 2 V
V
V
10
VIN = 4 V to 36 V, VEN= 36 V
100
nA
1
μA
VOLTAGE REFERENCE (FB PIN)
VREF
Reference voltage
ILKG_FB
Input leakage current at FB pin
VIN = 4 V to 36 V, TJ = 25 °C
0.985
1.0
1.015
VIN = 4 V to 36 V, TJ = -40 °C to 125 °C
0.980
1.0
1.020
VFB= 1 V
10
V
nA
POWER GOOD (PGOOD PIN)
VPG_OV
Power-good flag over voltage tripping
threshold
% of reference voltage
105
107
110
%
VPG_UV
Power-good flag under voltage tripping
threshold
% of reference voltage
92
94
96.5
%
VPG_HYS
Power-good flag recovery hysteresis
% of reference voltage
VIN_PG_MIN
Minimum VIN for valid PGOOD output
50 μA pull-up to PGOOD pin, VEN = 0 V,
TJ = 25 °C
1.5
PGOOD low level output voltage
50 μA pull-up to PGOOD pin, VIN = 1.5 V,
VEN = 0 V
0.4
VPG_LOW
0.5 mA pull-up to PGOOD pin, VIN =13.5
V, VEN = 0 V
0.4
1.5
%
V
V
INTERNAL LDO (VCC PIN)
VCC
Internal LDO output voltage
VCC_UVLO
4.1
VCC under voltage lockout thresholds
V
Rising threshold
2.8
3.2
3.6
Falling threshold
2.4
2.8
3.2
V
CURRENT LIMIT
IHS_LIMIT
Peak inductor current limit
3.8
5.0
6.2
A
ILS_LIMIT
Valley inductor current limit
2.9
3.6
4.6
A
IL_ZC
Zero cross current limit
IL_NEG
Negative current limit (FPWM Option)
-0.04
-2.7
-2.0
A
-1.3
A
INTEGRATED MOSFETS
RDS_ON_HS
High-side MOSFET ON-resistance
VIN = 12 V, IOUT = 1 A
185
mΩ
RDS_ON_LS
Low-side MOSFET ON-resistance
VIN = 12 V, IOUT = 1 A
105
mΩ
THERMAL SHUTDOWN
TSHDN
Thermal shutdown threshold
THYS
Hysteresis
6
162
170
15
Submit Documentation Feedback
178
°C
°C
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
LMR23630-Q1
www.ti.com
SNVSAR6 – DECEMBER 2016
7.6 Timing Characteristics
Over the recommended operating junction temperature range of -40 °C to 125 °C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
HICCUP MODE
NOC (1)
Number of cycles that LS current limit is
tripped to enter Hiccup mode
TOC
Hiccup retry delay time
64
SOIC package
5
WSON package
12
Cycles
ms
SOFT START
TSS
Internal soft-start time. The time of internal
reference to increase from 0 V to 1.0 V
SOIC package
WSON package
1
2
3
6
ms
POWER GOOD
TPGOOD_RISE
Power-good flag rising transition deglitch
delay
150
TPGOOD_FALL
Power-good flag falling transition deglitch
delay
18
(1)
μs
μs
Guaranteed by design.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
7
LMR23630-Q1
SNVSAR6 – DECEMBER 2016
www.ti.com
7.7 Switching Characteristics
Over the recommended operating junction temperature range of -40 °C to 125 °C (unless otherwise noted)
PARAMETER
TEST CONDITION
MIN
TYP
MAX
UNIT
90
ns
SW (SW PIN)
TON_MIN
Minimum turn-on time
60
TOFF_MIN (1)
Minimum turn-off time
100
ns
OSCILLATOR (RT and EN/SYNC PIN)
fSW_DEFAULT
Oscillator default frequency.
fADJ
Minimum adjustable frequency
Fixed frequency option or RT pin open
circuit
With RT resistor of 1% accuracy
Maximum adjustable frequency
340
400
460
kHz
180
200
220
kHz
1980
2200
2420
kHz
fSYNC
SYNC frequency range
200
2200
kHz
VSYNC
Amplitude of SYNC clock AC signal
(measured at SYNC pin)
2.8
5.5
V
TSYNC_MIN
Minimum sync clock ON and OFF time
(1)
8
100
ns
Guaranteed by design.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
LMR23630-Q1
www.ti.com
SNVSAR6 – DECEMBER 2016
7.8 Typical Characteristics
100
100
90
90
80
80
70
70
Efficiency (%)
Efficiency (%)
Unless otherwise specified the following conditions apply: VIN = 12 V, fSW = 400 kHz, L = 8.2 µH, COUT = 150 µF, TA = 25 °C.
60
50
40
PFM, VIN = 12 V
PFM, VIN = 24 V
PFM, VIN = 36 V
FPWM, VIN = 12 V
FPWM, VIN = 24 V
FPWM, VIN = 36 V
30
20
10
0
1E-5
0.0001
0.001
fSW = 400 kHz
0.01
IOUT (A)
0.1
1
60
50
40
PFM, VIN = 12 V
PFM, VIN = 24 V
PFM, VIN = 36 V
FPWM, VIN = 12 V
FPWM, VIN = 24 V
FPWM, VIN = 36 V
30
20
10
0
1E-5
10
0.0001
VOUT = 5 V
fSW = 400 kHz
90
90
80
80
70
70
60
50
40
PFM, VIN = 12 V
PFM, VIN = 24 V
PFM, VIN = 36 V
FPWM, VIN = 12 V
FPWM, VIN = 24 V
FPWM, VIN = 36 V
30
20
10
0.0001
0.001
fSW = 200 kHz
(Sync)
0.01
IOUT (A)
0.1
1
0.1
1
10
D002
VOUT = 3.3 V
60
50
40
PFM, VIN = 12 V
PFM, VIN = 24 V
PFM, VIN = 36 V
FPWM, VIN = 12 V
FPWM, VIN = 24 V
FPWM, VIN = 36 V
30
20
10
0
1E-5
10
0.0001
0.001
D003
VOUT = 5 V
fSW = 200 kHz
(Sync)
Figure 3. Efficiency vs. Load Current
0.01
IOUT (A)
0.1
1
10
D004
VOUT = 3.3 V
Figure 4. Efficiency vs. Load Current
5.015
5.09
VIN = 12 V
VIN = 24 V
VIN = 36 V
VIN = 12 V
VIN = 24 V
VIN = 36 V
5.08
5.07
5.06
5.01
5.05
VOUT (V)
VOUT (V)
0.01
IOUT (A)
Figure 2. Efficiency vs. Load Current
100
Efficiency (%)
Efficiency (%)
Figure 1. Efficiency vs. Load Current
100
0
1E-5
0.001
D001
5.04
5.03
5.005
5.02
5.01
5
5
4.99
0
0.5
PFM Option
1
1.5
IOUT (A)
2
VOUT = 5 V
2.5
3
0
0.5
D004
FPWM Option
Figure 5. Load Regulation
1
1.5
IOUT (A)
2
2.5
3
D005
VOUT = 5 V
Figure 6. Load Regulation
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
9
LMR23630-Q1
SNVSAR6 – DECEMBER 2016
www.ti.com
Typical Characteristics (continued)
Unless otherwise specified the following conditions apply: VIN = 12 V, fSW = 400 kHz, L = 8.2 µH, COUT = 150 µF, TA = 25 °C.
5.5
3.6
5
4.5
VOUT (V)
VOUT (V)
3.3
4
2.7
IOUT = 0.5 A
IOUT = 1.0 A
IOUT = 2.0 A
IOUT = 3.0 A
3.5
3
4
4.5
5
VIN (V)
5.5
3
IOUT = 0.5 A
IOUT = 1.0 A
IOUT = 2.0 A
IOUT = 3.0 A
2.4
3.3
6
3.5
3.7
D006
VOUT = 5 V
4.1
4.3
4.5
D007
VOUT = 3.3 V
Figure 7. Dropout Curve
Figure 8. Dropout Curve
3.67
VIN UVLO Rising Threshold (V)
80
75
IQ (µA)
3.9
VIN (V)
70
65
60
-50
0
50
Temperature (°C)
VIN = 12 V
100
3.66
3.65
3.64
3.63
3.62
3.61
-50
150
0
D008
50
Temperature (°C)
100
150
D009
VFB = 1.1 V
Figure 9. IQ vs. Junction Temperature
Figure 10. VIN UVLO Rising Threshold vs. Junction
Temperature
5.5
0.425
5
Current Limit (A)
VIN UVLO Hysteresis (V)
LS Limit
HS Limit
0.42
0.415
4.5
4
3.5
0.41
-50
0
50
Temperature (°C)
100
150
3
-50
D010
0
50
Temperature (°C)
100
150
D011
VIN = 12 V
Figure 11. VIN UVLO Hysteresis vs. Junction Temperature
10
Figure 12. HS & LS Current Limit vs. Junction Temperature
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
LMR23630-Q1
www.ti.com
SNVSAR6 – DECEMBER 2016
8 Detailed Description
8.1 Overview
The LMR23630-Q1 SIMPLE SWITCHER® regulator is an easy to use synchronous step-down DC-DC converter
operating from 4 V to 36 V supply voltage. It is capable of delivering up to 3 A DC load current with good thermal
performance in a small solution size. For both SOIC and WSON package, an extended family is available in
multiple current options from 1 A to 3 A in pin-to-pin compatible packages.
The LMR23630-Q1 employs constant frequency peak current mode control. The device enters PFM mode at
light load to achieve high efficiency. A user selectable FPWM option is provided to achieve low output voltage
ripple, tight output voltage regulation, and constant switching frequency. The device is internally compensated,
which reduces design time, and requires few external components. The switching frequency is fixed 400 kHz. For
the option which has RT pin, the switching frequency is adjustable from 200 kHz to 2.2 MHz. Also the
LMR23630-Q1 is capable of synchronization to an external clock within the range of 200 kHz to 2.2 MHz.
Additional features such as precision enable, power good flag and internal soft-start provide a flexible and easy
to use solution for a wide range of applications. Protection features include thermal shutdown, VIN and VCC
under-voltage lockout, cycle-by-cycle current limit, and hiccup mode short-circuit protection.
The family requires very few external components and has a pin-out designed for simple, optimum PCB layout.
8.2 Functional Block Diagram
VCC
EN/SYNC
SYNC Signal
SYNC
Detector
VCC
Enable
LDO
VIN
Precision
Enable
Internal
SS
CBOOT
HS I Sense
EA
REF
Rc
TSD
UVLO
Cc
(PGOOD)
PWM CONTROL LOGIC
PFM
Detector
OV/UV
Detector
SW
FB
Slope
Comp
Freq
Foldback
AGND
Zero
Cross
HICCUP
Detector
SYNC Signal
(RT)
Oscillator
LS I Sense
FB
PGND
Copyright © 2016, Texas Instruments Incorporated
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
11
LMR23630-Q1
SNVSAR6 – DECEMBER 2016
www.ti.com
8.3 Feature Description
8.3.1 Fixed Frequency Peak Current Mode Control
The following operating description of the LMR23630-Q1 will refer to the Functional Block Diagram and to the
waveforms in Figure 13. LMR23630-Q1 is a step-down synchronous buck regulator with integrated high-side
(HS) and low-side (LS) switches (synchronous rectifier). The LMR23630-Q1 supplies a regulated output voltage
by turning on the HS and LS NMOS switches with controlled duty cycle. During high-side switch ON time, the
SW pin voltage swings up to approximately VIN, and the inductor current iL increase with linear slope (VIN – VOUT)
/ L. When the HS switch is turned off by the control logic, the LS switch is turned on after an anti-shoot-through
dead time. Inductor current discharges through the LS switch with a slope of –VOUT / L. The control parameter of
a buck converter is defined as Duty Cycle D = tON / TSW, where tON is the high-side switch ON time and TSW is
the switching period. The regulator control loop maintains a constant output voltage by adjusting the duty cycle
D. In an ideal buck converter, where losses are ignored, D is proportional to the output voltage and inversely
proportional to the input voltage: D = VOUT / VIN.
VSW
SW Voltage
D = tON/ TSW
VIN
tON
tOFF
t
0
-VD
Inductor Current
iL
TSW
ILPK
IOUT
'iL
t
0
Figure 13. SW Node and Inductor Current Waveforms in
Continuous Conduction Mode (CCM)
The LMR23630-Q1 employs fixed frequency peak current mode control. A voltage feedback loop is used to get
accurate DC voltage regulation by adjusting the peak current command based on voltage offset. The peak
inductor current is sensed from the high-side switch and compared to the peak current threshold to control the
ON time of the high-side switch. The voltage feedback loop is internally compensated, which allows for fewer
external components, makes it easy to design, and provides stable operation with almost any combination of
output capacitors. The regulator operates with fixed switching frequency at normal load condition. At light load
condition, the LMR23630-Q1 will operate in PFM mode to maintain high efficiency (PFM option) or in FPWM
mode for low output voltage ripple, tight output voltage regulation, and constant switching frequency (FPWM
option).
8.3.2 Adjustable Frequency
For adjustable switching frequency option of LMR23630-Q1. The switching frequency can be programmed by the
impedance RT from the RT pin to ground. The frequency is inversely proportional to the RT resistance. The RT
pin can be left floating and the LMR23630-Q1 will operate at 400 kHz default switching frequency. The RT pin is
not designed to be shorted to ground. For a desired requency, typical RT resistance can be found by Equation 1.
Table 1 gives typical RT values for a given fSW.
12
RT(kΩ) = 40200 / fSW(kHz) - 0.6
(1)
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
LMR23630-Q1
www.ti.com
SNVSAR6 – DECEMBER 2016
Feature Description (continued)
250
RT Resistance (kŸ)
200
150
100
50
0
0
500
1000
1500
2000
Switching Frequency (kHz)
2500
C008
Figure 14. RT vs Frequency Curve
Table 1. Typical Frequency Setting RT Resistance
fSW (kHz)
RT (kΩ)
200
200
350
115
500
78.7
750
53.6
1000
39.2
1500
26.1
2000
19.6
2200
17.8
8.3.3 Adjustable Output Voltage
A precision 1.0 V reference voltage is used to maintain a tightly regulated output voltage over the entire
operating temperature range. The output voltage is set by a resistor divider from output voltage to the FB pin. It
is recommended to use 1% tolerance resistors with a low temperature coefficient for the FB divider. Select the
low-side resistor RFBB for the desired divider current and use Equation 2 to calculate high-side RFBT. RFBT in the
range from 10 kΩ to 100 kΩ is recommended for most applications. A lower RFBT value can be used if static
loading is desired to reduce VOUT offset in PFM operation. Lower RFBT will reduce efficiency at very light load.
Less static current goes through a larger RFBT and might be more desirable when light load efficiency is critical.
But RFBT larger than 1 MΩ is not recommended because it makes the feedback path more susceptible to noise.
Larger RFBT value requires more carefully designed feedback path on the PCB. The tolerance and temperature
variation of the resistor dividers affect the output voltage regulation.
VOUT
RFBT
FB
RFBB
Figure 15. Output Voltage Setting
RFBT
VOUT VREF
u RFBB
VREF
(2)
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
13
LMR23630-Q1
SNVSAR6 – DECEMBER 2016
www.ti.com
8.3.4 Enable/Sync
The voltage on the EN pin controls the ON or OFF operation of LMR23630-Q1. A voltage less than 1 V (typ) will
shut-down the device while a voltage higher than 1.6 V (typ) is required to start the regulator. The EN pin is an
input and can not be left open or floating. The simplest way to enable the operation of the LMR23630-Q1 is to
connect the EN to VIN. This allows self-start-up of the LMR23630-Q1 when VIN is within the operation range.
Many applications will benefit from the employment of an enable divider RENT and RENB (Figure 16) to establish a
precision system UVLO level for the converter. System UVLO can be used for supplies operating from utility
power as well as battery power. It can be used for sequencing, ensuring reliable operation, or supply protection,
such as a battery discharge level. An external logic signal can also be used to drive EN input for system
sequencing and protection.
VIN
RENT
EN/SYNC
RENB
Figure 16. System UVLO by Enable Divider
The EN pin also can be used to synchronize the internal oscillator to an external clock. The internal oscillator can
be synchronized by AC coupling a positive edge into the EN pin. The AC coupled peak-to-peak voltage at the EN
pin must exceed the SYNC amplitude threshold of 2.8 V (typ) to trip the internal synchronization pulse detector,
and the minimum SYNC clock ON and OFF time must be longer than 100ns (typ). A 3.3 V or a higher amplitude
pulse signal coupled through a 1 nF capacitor CSYNC is a good starting point. Keeping RENT // RENB (RENT parallel
with RENB) in the 100 kΩ range is a good choice. RENT is required for this synchronization circuit, but RENB can be
left unmounted if system UVLO is not needed. LMR23630-Q1 switching action can be synchronized to an
external clock from 200 kHz to 2.2 MHz. Figure 18 and Figure 19 show the device synchronized to an external
system clock.
VIN
CSYNC
RENT
EN/SYNC
RENB
Clock
Source
Figure 17. Synchronize to external clock
14
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
LMR23630-Q1
www.ti.com
SNVSAR6 – DECEMBER 2016
Figure 18. Synchronizing in PWM Mode
Figure 19. Synchronizing in PFM Mode
8.3.5 VCC, UVLO
The LMR23630-Q1 integrates an internal LDO to generate VCC for control circuitry and MOSFET drivers. The
nominal voltage for VCC is 4.1 V. The VCC pin is the output of an LDO and must be properly bypassed. A high
quality ceramic capacitor with a value of 2.2 µF to 10 µF, 16 V or higher rated voltage should be placed as close
as possible to VCC and grounded to the exposed PAD and ground pins. The VCC output pin should not be
loaded, or shorted to ground during operation. Shorting VCC to ground during operation may cause damage to
the LMR23630-Q1.
VCC under voltage lockout (UVLO) prevents the LMR23630-Q1 from operating until the VCC voltage exceeds 3.2
V (typ). The VCC UVLO threshold has 400 mV (typ) of hysteresis to prevent undesired shutdown due to
temporary VIN drops.
8.3.6 Minimum ON-time, Minimum OFF-time and Frequency Foldback at Drop-out Conditions
Minimum ON-time, TON_MIN, is the smallest duration of time that the HS switch can be on. TON_MIN is typically 60
ns in the LMR23630-Q1. Minimum OFF-time, TOFF_MIN, is the smallest duration that the HS switch can be off.
TOFF_MIN is typically 100 ns in the LMR23630-Q1. In CCM operation, TON_MIN and TOFF_MIN limit the voltage
conversion range given a selected switching frequency.
The minimum duty cycle allowed is:
DMIN = TON_MIN x fSW
(3)
And the maximum duty cycle allowed is:
DMAX = 1 - TOFF_MIN x fSW
(4)
Given fixed TON_MIN and TOFF_MIN, the higher the switching frequency the narrower the range of the allowed duty
cycle. In the LMR23630-Q1, a frequency foldback scheme is employed to extend the maximum duty cycle when
TOFF_MIN is reached. The switching frequency will decrease once longer duty cycle is needed under low VIN
conditions. Wide range of frequency foldback allows the LMR23630-Q1 output voltage stay in regulation with a
much lower supply voltage VIN. This leads to a lower effective drop-out voltage.
Given an output voltage, the choice of the switching frequency affects the allowed input voltage range, solution
size and efficiency. The maximum operation supply voltage can be found by:
VOUT
VIN _ MAX
fSW u TON _ MIN
(5)
At lower supply voltage, the switching frequency will decrease once TOFF_MIN is tripped. The minimum VIN without
frequency foldback can be approximated by:
VOUT
VIN _ MIN
1 fSW u TOFF _ MIN
(6)
Taking considerations of power losses in the system with heavy load operation, VIN_MAX is higher than the result
calculated in Equation 5. With frequency foldback, VIN_MIN is lowered by decreased fSW.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
15
LMR23630-Q1
SNVSAR6 – DECEMBER 2016
www.ti.com
450
400
Frequency (kHz)
350
300
250
200
150
IOUT = 0.5 A
IOUT = 1.0 A
IOUT = 2.0 A
IOUT = 3.0 A
100
50
0
4.6
4.8
5
5.2
5.4
5.6
VIN (V)
5.8
6
6.2
6.4
D013
Figure 20. Frequency Foldback at Dropout (VOUT = 5 V, fSW = 400 kHz)
8.3.7 Power Good (PGOOD)
For power good option of LMR23630-Q1. It has a built in power-good flag shown on PGOOD pin to indicate
whether the output voltage is within its regulation level. The PGOOD signal can be used for start-up sequencing
of multiple rails or fault protection. The PGOOD pin is an open-drain output that requires a pull-up resistor to an
appropriate DC voltage. Voltage seen by the PGOOD pin should never exceed 15 V, and the maximum current
into this pin should be limited to 1 mA. A typical range of pull-up resistor value is 10 kΩ to 100 kΩ.
When the FB voltage is within the power-good band, +6% above and -6% below the internal reference voltage
VREF typically, the PGOOD switch will be turned off and the PGOOD voltage will be as high as the pulled-up
voltage. When the FB voltage is outside of the tolerance band, +7% above or -7% below VREF typically, the
PGOOD switch will be turned on and the PGOOD pin voltage will be pulled low to indicate power bad. A glitch
filter prevents false flag operation for short excursions in the output voltage, such as during line and load
transients. The values for the various filter and delay times can be found in the Timing Characteristics table.
Power-good operation can best be understood by reference to Figure 21.
VREF
107%
106%
94%
93%
PGOOD
High
Low
Figure 21. Power-Good Flag
8.3.8 Internal Compensation and CFF
The LMR23630-Q1 is internally compensated as shown in Functional Block Diagram. The internal compensation
is designed such that the loop response is stable over the entire operating frequency and output voltage range.
Depending on the output voltage, the compensation loop phase margin can be low with all ceramic capacitors.
An external feed-forward capacitor CFF is recommended to be placed in parallel with the top resistor divider RFBT
for optimum transient performance.
16
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
LMR23630-Q1
www.ti.com
SNVSAR6 – DECEMBER 2016
VOUT
RFBT
CFF
FB
RFBB
Figure 22. Feedforward Capacitor for Loop Compensation
The feed-forward capacitor CFF in parallel with RFBT places an additional zero before the cross over frequency of
the control loop to boost phase margin. The zero frequency can be found by
1
fZ _ CFF
2S u CFF u RFBT
(7)
An additional pole is also introduced with CFF at the frequency of
1
fP _ CFF
2S u CFF u RFBT //RFBB
(8)
The zero fZ_CFF adds phase boost at the crossover frequency and improves transient response. The pole fP-CFF
helps maintaining proper gain margin at frequency beyond the crossover. Table 2 lists the combination of COUT,
CFF and RFBT for typical applications, designs with similar COUT but RFBT other than recommended value, please
adjust CFF such that (CFF × RFBT) is unchanged and adjust RFBB such that (RFBT / RFBB) is unchanged.
Designs with different combinations of output capacitors need different CFF. Different types of capacitors have
different Equivalent Series Resistance (ESR). Ceramic capacitors have the smallest ESR and need the most
CFF. Electrolytic capacitors have much larger ESR and the ESR zero frequency
1
fZ _ESR
2S u COUT u ESR
(9)
would be low enough to boost the phase up around the crossover frequency. Designs using mostly electrolytic
capacitors at the output may not need any CFF.
The CFF creates a time constant with RFBT that couples in the attenuate output voltage ripple to the FB node. If
the CFF value is too large, it can couple too much ripple to the FB and affect VOUT regulation. Therefore, CFF
should be calculated based on output capacitors used in the system. At cold temperatures, the value of CFF
might change based on the tolerance of the chosen component. This may reduce its impedance and ease noise
coupling on the FB node. To avoid this, more capacitance can be added to the output or the value of CFF can be
reduced.
8.3.9 Bootstrap Voltage (BOOT)
The LMR23630-Q1 provides an integrated bootstrap voltage regulator. A small capacitor between the BOOT and
SW pins provides the gate drive voltage for the high-side MOSFET. The BOOT capacitor is refreshed when the
high-side MOSFET is off and the low-side switch conducts. The recommended value of the BOOT capacitor is
0.1 μF or higher. A ceramic capacitor with an X7R or X5R grade dielectric with a voltage rating of 16V or higher
is recommended for stable performance over temperature and voltage.
8.3.10 Over Current and Short Circuit Protection
The LMR23630-Q1 is protected from over-current conditions by cycle-by-cycle current limit on both the peak and
valley of the inductor current. Hiccup mode will be activated if a fault condition persists to prevent over-heating.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
17
LMR23630-Q1
SNVSAR6 – DECEMBER 2016
www.ti.com
High-side MOSFET over-current protection is implemented by the nature of the Peak Current Mode control. The
HS switch current is sensed when the HS is turned on after a set blanking time. The HS switch current is
compared to the output of the Error Amplifier (EA) minus slope compensation every switching cycle. Please refer
to Functional Block Diagram for more details. The peak current of HS switch is limited by a clamped maximum
peak current threshold IHS_LIMIT which is constant. So the peak current limit of the high-side switch is not affected
by the slope compensation and remains constant over the full duty cycle range.
The current going through LS MOSFET is also sensed and monitored. When the LS switch turns on, the inductor
current begins to ramp down. The LS switch will not be turned OFF at the end of a switching cycle if its current is
above the LS current limit ILS_LIMIT. The LS switch will be kept ON so that inductor current keeps ramping down,
until the inductor current ramps below the LS current limit ILS_LIMIT. Then the LS switch will be turned OFF and
the HS switch will be turned on after a dead time. This is somewhat different than the more typical peak current
limit, and results in Equation 10 for the maximum load current.
VIN VOUT
V
IOUT _ MAX ILS _ LIMIT
u OUT
2 u fSW u L
VIN
(10)
If the current of the LS switch is higher than the LS current limit for 64 consecutive cycles, hiccup current
protection mode will be activated. In hiccup mode, the regulator will be shut down and kept off for 5 ms typically
before the LMR23630-Q1 tries to start again. If over-current or short-circuit fault condition still exist, hiccup will
repeat until the fault condition is removed. Hiccup mode reduces power dissipation under severe over-current
conditions, prevents over-heating and potential damage to the device.
For FPWM option, the inductor current is allowed to go negative. Should this current exceed IL_NEG, the LS switch
is turned off until the next clock cycle. This is used to protect the LS switch from excessive negative current.
8.3.11 Thermal Shutdown
The LMR23630-Q1 provides an internal thermal shutdown to protect the device when the junction temperature
exceeds 170 °C (typ). The device is turned off when thermal shutdown activates. Once the die temperature falls
below 155 °C (typ), the device reinitiates the power up sequence controlled by the internal soft-start circuitry.
18
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
LMR23630-Q1
www.ti.com
SNVSAR6 – DECEMBER 2016
8.4 Device Functional Modes
8.4.1 Shutdown Mode
The EN pin provides electrical ON and OFF control for the LMR23630-Q1. When VEN is below 1 V (typ), the
device is in shutdown mode. The LMR23630-Q1 also employs VIN and VCC under voltage lock out protection. If
VIN or VCC voltage is below their respective UVLO level, the regulator will be turned off.
8.4.2 Active Mode
The LMR23630-Q1 is in Active Mode when VEN is above the precision enable threshold, VIN and VCC are above
their respective UVLO level. The simplest way to enable the LMR23630-Q1 is to connect the EN pin to VIN pin.
This allows self startup when the input voltage is in the operating range: 4 V to 36 V. Please refer to VCC, UVLO
and Enable/Sync for details on setting these operating levels.
In Active Mode, depending on the load current, the LMR23630-Q1 will be in one of four modes:
1. Continuous conduction mode (CCM) with fixed switching frequency when load current is above half of the
peak-to-peak inductor current ripple (for both PFM and FPWM options).
2. Discontinuous conduction mode (DCM) with fixed switching frequency when load current is lower than half of
the peak-to-peak inductor current ripple in CCM operation (only for PFM option).
3. Pulse frequency modulation mode (PFM) when switching frequency is decreased at very light load (only for
PFM option).
4. Forced pulse width modulation mode (FPWM) with fixed switching frequency even at light load (only for
FPWM option).
8.4.3 CCM Mode
CCM operation is employed in the LMR23630-Q1 when the load current is higher than half of the peak-to-peak
inductor current. In CCM operation, the frequency of operation is fixed, output voltage ripple will be at a minimum
in this mode and the maximum output current of 3 A can be supplied by the LMR23630-Q1.
8.4.4 Light Load Operation (PFM Option)
For PFM option, when the load current is lower than half of the peak-to-peak inductor current in CCM, the
LMR23630-Q1 will operate in Discontinuous Conduction Mode (DCM), also known as Diode Emulation Mode
(DEM). In DCM, the LS switch is turned off when the inductor current drops to IL_ZC (-40 mA typ). Both switching
losses and conduction losses are reduced in DCM, compared to forced PWM operation at light load.
At even lighter current loads, Pulse Frequency Modulation mode (PFM) is activated to maintain high efficiency
operation. When either the minimum HS switch ON time (tON_MIN ) or the minimum peak inductor current IPEAK_MIN
(300 mA typ) is reached, the switching frequency will decrease to maintain regulation. In PFM, switching
frequency is decreased by the control loop when load current reduces to maintain output voltage regulation.
Switching loss is further reduced in PFM operation due to less frequent switching actions. The external clock
synchronizing will not be valid when LMR23630-Q1 enters into PFM mode.
8.4.5 Light Load Operation (FPWM Option)
For FPWM option, LMR23630-Q1 is locked in PWM mode at full load range. This operation is maintained, even
at no-load, by allowing the inductor current to reverse its normal direction. This mode trades off reduced light
load efficiency for low output voltage ripple, tight output voltage regulation, and constant switching frequency. In
this mode, a negative current limit of IL_NEG is imposed to prevent damage to the regulators low side FET. When
in FPWM mode the converter will synchronize to any valid clock signal on the EN/SYNC input.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
19
LMR23630-Q1
SNVSAR6 – DECEMBER 2016
www.ti.com
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The LMR23630-Q1 is a step down DC-to-DC regulator. It is typically used to convert a higher DC voltage to a
lower DC voltage with a maximum output current of 3 A. The following design procedure can be used to select
components for the LMR23630-Q1. Alternately, the WEBENCH® software may be used to generate complete
designs. When generating a design, the WEBENCH® software utilizes iterative design procedure and accesses
comprehensive databases of components. Please go to ti.com for more details.
9.2 Typical Applications
The LMR23630-Q1 only requires a few external components to convert from a wide voltage range supply to a
fixed output voltage. Figure 23 shows a basic schematic.
VIN 12 V
CBOOT
0.1 F
BOOT
VIN
L
10 H
CIN
10 F
VOUT
5 V/3 A
SW
EN/
SYNC
PAD
CFF
47 pF
RFBT
88.7 kŸ
FB
CVCC
2.2 F
RFBB
22.1 kŸ
VCC
PGND
COUT
100 F
AGND
Copyright © 2016, Texas Instruments Incorporated
Figure 23. Application Circuit
The external components have to fulfill the needs of the application, but also the stability criteria of the device's
control loop. Table 2 can be used to simplify the output filter component selection.
Table 2. L, COUT and CFF Typical Values
fSW (kHz)
VOUT (V)
L (µH)
COUT (µF)
CFF (pF)
RFBT (kΩ)
400
3.3
6.8
150
75
51
400
5
10
100
47
88.7
400
12
15
68
See note (5)
243
400
24
15
47
See note (5)
510
1.
2.
3.
4.
Inductance value is calculated based on VIN = 36 V.
All the COUT values are after derating. Add more when using ceramic capacitors.
RFBT = 0 Ω for VOUT = 1 V. RFBB = 22.1 kΩ for all other VOUT setting.
For designs with RFBT other than recommended value, please adjust CFF such that (CFF × RFBT) is
unchanged and adjust RFBB such that (RFBT / RFBB) is unchanged.
5. High ESR COUT will give enough phase boost and CFF not needed.
9.2.1 Design Requirements
Detailed design procedure is described based on a design example. For this design example, use the
parameters listed in Table 3 as the input parameters.
20
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
LMR23630-Q1
www.ti.com
SNVSAR6 – DECEMBER 2016
Table 3. Design Example Parameters
Input Voltage, VIN
12 V typical, range from 8 V to 28 V
Output Voltage, VOUT
5V
Maximum Output Current IO_MAX
3A
Transient Response 0.3 A to 3 A
5%
Output Voltage Ripple
50 mV
Input Voltage Ripple
400 mV
Switching Frequency fSW
400 kHz
9.2.2 Detailed Design Procedure
9.2.2.1
Output Voltage Set-Point
The output voltage of LMR23630-Q1 is externally adjustable using a resistor divider network. The divider network
is comprised of top feedback resistor RFBT and bottom feedback resistor RFBB. Equation 11 is used to determine
the output voltage:
VOUT VREF
u RFBB
RFBT
VREF
(11)
Choose the value of RFBB to be 22.1 kΩ. With the desired output voltage set to 5 V and the VREF = 1.0 V, the
RFBB value can then be calculated using Equation 11. The formula yields to a value 88.7 kΩ.
9.2.2.2
Switching Frequency
The default switching frequency of the LMR23630-Q1 is 400 kHz. For other required switching frequency, adjust
RT value or synchronize the device to an external clock to get the target frequency, refer to Adjustable Frequency
andEnable/Sync for more details.
9.2.2.3
Inductor Selection
The most critical parameters for the inductor are the inductance, saturation current and the rated current. The
inductance is based on the desired peak-to-peak ripple current ΔiL. Since the ripple current increases with the
input voltage, the maximum input voltage is always used to calculate the minimum inductance LMIN. Use
Equation 13 to calculate the minimum value of the output inductor. KIND is a coefficient that represents the
amount of inductor ripple current relative to the maximum output current of the device. A reasonable value of
KIND should be 20% to 40%. During an instantaneous short or over current operation event, the RMS and peak
inductor current can be high. The inductor current rating should be higher than the current limit of the device.
'iL
LMIN
VOUT u VIN _ MAX
VOUT
VIN _ MAX u L u fSW
VIN _ MAX
VOUT
IOUT u KIND
(12)
VOUT
u
VIN _ MAX u fSW
(13)
In general, it is preferable to choose lower inductance in switching power supplies, because it usually
corresponds to faster transient response, smaller DCR, and reduced size for more compact designs. But too low
of an inductance can generate too large of an inductor current ripple such that over current protection at the full
load could be falsely triggered. It also generates more conduction loss and inductor core loss. Larger inductor
current ripple also implies larger output voltage ripple with same output capacitors. With peak current mode
control, it is not recommended to have too small of an inductor current ripple. A larger peak current ripple
improves the comparator signal to noise ratio.
For this design example, choose KIND = 0.4, the minimum inductor value is calculated to be 8.56 µH. Choose the
nearest standard 8.2 μH ferrite inductor with a capability of 4 A RMS current and 6 A saturation current.
9.2.2.4
Output Capacitor Selection
The output capacitor(s), COUT, should be chosen with care since it directly affects the steady state output voltage
ripple, loop stability and the voltage over/undershoot during load current transients.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
21
LMR23630-Q1
SNVSAR6 – DECEMBER 2016
www.ti.com
The output ripple is essentially composed of two parts. One is caused by the inductor current ripple going
through the Equivalent Series Resistance (ESR) of the output capacitors:
'VOUT_ESR 'iL u ESR KIND u IOUT u ESR
(14)
The other is caused by the inductor current ripple charging and discharging the output capacitors:
KIND u IOUT
'iL
'VOUT _ C
8 u fSW u COUT
8 u fSW u COUT
(15)
The two components in the voltage ripple are not in phase, so the actual peak-to-peak ripple is smaller than the
sum of two peaks.
Output capacitance is usually limited by transient performance specifications if the system requires tight voltage
regulation with presence of large current steps and fast slew rate. When a fast large load increase happens,
output capacitors provide the required charge before the inductor current can slew up to the appropriate level.
The regulator’s control loop usually needs four or more clock cycles to respond to the output voltage droop. The
output capacitance must be large enough to supply the current difference for four clock cycles to maintain the
output voltage within the specified range. Equation 16 shows the minimum output capacitance needed for
specified output undershoot. When a sudden large load decrease happens, the output capacitors absorb energy
stored in the inductor. which results in an output voltage overshoot. Equation 17 calculates the minimum
capacitance required to keep the voltage overshoot within a specified range.
4 u IOH IOL
COUT !
fSW u VUS
(16)
COUT !
2
2
IOH
IOL
VOUT u VOS
2
2
VOUT
uL
(17)
where
• KIND = Ripple ratio of the inductor ripple current (ΔiL / IOUT)
• IOL = Low level output current during load transient
• IOH = High level output current during load transient
• VUS = Target output voltage undershoot
• VOS = Target output voltage overshoot
For this design example, the target output ripple is 50 mV. Presuppose ΔVOUT_ESR = ΔVOUT_C = 50 mV, and
chose KIND = 0.4. Equation 14 yields ESR no larger than 41.7 mΩ and Equation 15 yields COUT no smaller than
7.5 μF. For the target over/undershoot range of this design, VUS = VOS = 5% × VOUT = 250 mV. The COUT can be
calculated to be no smaller than 108 μF and 28.5 μF by Equation 16 and Equation 17 respectively. Consider of
derating, one 47 μF, 16 V and one 100 μF, 10V ceramic capacitor with 5 mΩ ESR are used in parallel.
9.2.2.5
Feed-Forward Capacitor
The LMR23630-Q1 is internally compensated. Depending on the VOUT and frequency fSW, if the output capacitor
COUT is dominated by low ESR (ceramic types) capacitors, it could result in low phase margin. To improve the
phase boost an external feedforward capacitor CFF can be added in parallel with RFBT. CFF is chosen such that
phase margin is boosted at the crossover frequency without CFF. A simple estimation for the crossover frequency
(fX) without CFF is shown in Equation 18, assuming COUT has very small ESR, and COUT value is after derating.
8.32
fX
VOUT u COUT
(18)
The following equation for CFF was tested:
1
CFF
4S u fX u RFBT
(19)
For designs with higher ESR, CFF is not needed when COUT has very high ESR and CFF calculated from
Equation 19 should be reduced with medium ESR. Table 2 can be used as a quick starting point.
For the application in this design example, a 47 pF, 50 V, COG capacitor is selected.
22
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
LMR23630-Q1
www.ti.com
9.2.2.6
SNVSAR6 – DECEMBER 2016
Input Capacitor Selection
The LMR23630-Q1 device requires high frequency input decoupling capacitor(s) and a bulk input capacitor,
depending on the application. The typical recommended value for the high frequency decoupling capacitor is 4.7
μF to 10 μF. A high-quality ceramic capacitor type X5R or X7R with sufficiency voltage rating is recommended.
To compensate the derating of ceramic capacitors, a voltage rating of twice the maximum input voltage is
recommended. Additionally, some bulk capacitance can be required, especially if the LMR23630-Q1 circuit is not
located within approximately 5 cm from the input voltage source. This capacitor is used to provide damping to the
voltage spike due to the lead inductance of the cable or the trace. For this design, two 4.7 μF, 50 V, X7R ceramic
capacitors are used. A 0.1 μF for high-frequency filtering and place it as close as possible to the device pins.
9.2.2.7
Bootstrap Capacitor Selection
Every LMR23630-Q1 design requires a bootstrap capacitor (CBOOT). The recommended capacitor is 0.1 μF and
rated 16 V or higher. The bootstrap capacitor is located between the SW pin and the BOOT pin. The bootstrap
capacitor must be a high-quality ceramic type with an X7R or X5R grade dielectric for temperature stability.
9.2.2.8 VCC Capacitor Selection
The VCC pin is the output of an internal LDO for LMR23630-Q1. To insure stability of the device, place a
minimum of 2.2 μF, 16 V, X7R capacitor from this pin to ground.
9.2.2.9 Under Voltage Lockout Set-Point
The system undervoltage lockout (UVLO) is adjusted using the external voltage divider network of RENT and
RENB. The UVLO has two thresholds, one for power up when the input voltage is rising and one for power down
or brown outs when the input voltage is falling. The following equation can be used to determine the VIN UVLO
level.
R
RENB
VIN _ RISING VENH u ENT
RENB
(20)
The EN rising threshold (VENH) for LMR23630-Q1 is set to be 1.55 V (typ). Choose the value of RENB to be 287
kΩ to minimize input current from the supply. If the desired VIN UVLO level is at 6.0 V, then the value of RENT can
be calculated using the equation below:
§ VIN _ RISING
·
RENT ¨¨
1¸¸ u RENB
© VENH
¹
(21)
The above equation yields a value of 820 kΩ. The resulting falling UVLO threshold, equals 4.4 V, can be
calculated by below equation, where EN hysteresis (VEN_HYS) is 0.4 V (typ).
R
RENB
VIN _ FALLING
VENH VEN _ HYS u ENT
RENB
(22)
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
23
LMR23630-Q1
SNVSAR6 – DECEMBER 2016
www.ti.com
9.2.3 Application Curves
Unless otherwise specified the following conditions apply: VIN = 12 V, fSW = 400 kHz, L = 8.2 µH, COUT = 150 µF, TA = 25 °C.
VOUT = 5 V
IOUT = 3 A
fSW = 400 kHz
VOUT = 5 V
Figure 24. CCM Mode
VOUT = 5 V
IOUT = 0 mA
VOUT = 5 V
fSW = 400 kHz
VOUT = 5 V
IOUT = 0 mA
fSW = 400 kHz
Figure 27. FPWM Mode
IOUT = 2 A
VIN = 12 V
Figure 28. Start Up by VIN
24
fSW = 400 kHz
Figure 25. DCM Mode
Figure 26. PFM Mode
VIN = 12 V
IOUT = 150 mA
VOUT = 5 V
IOUT = 2 A
Figure 29. Start Up by EN
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
LMR23630-Q1
www.ti.com
SNVSAR6 – DECEMBER 2016
Unless otherwise specified the following conditions apply: VIN = 12 V, fSW = 400 kHz, L = 8.2 µH, COUT = 150 µF, TA = 25 °C.
VIN = 12 V
VOUT = 5 V
IOUT = 0.3 A to 3 A,
100 mA / μs
VOUT = 7 V to 36
V, 2 V / μs
Figure 30. Load Transient
VOUT = 5 V
VOUT = 5 V
IOUT = 3 A
Figure 31. Line Transient
IOUT = 1 A to short
VOUT = 5 V
Figure 32. Short Protection
IOUT = short to 1 A
Figure 33. Short Recovery
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
25
LMR23630-Q1
SNVSAR6 – DECEMBER 2016
www.ti.com
10 Power Supply Recommendations
The LMR23630-Q1 is designed to operate from an input voltage supply range between 4 V and 36 V. This input
supply should be able to withstand the maximum input current and maintain a stable voltage. The resistance of
the input supply rail should be low enough that an input current transient does not cause a high enough drop at
the LMR23630-Q1 supply voltage that can cause a false UVLO fault triggering and system reset. If the input
supply is located more than a few inches from the LMR23630-Q1, additional bulk capacitance may be required in
addition to the ceramic input capacitors. The amount of bulk capacitance is not critical, but a 47 μF or 100 μF
electrolytic capacitor is a typical choice.
11 Layout
11.1 Layout Guidelines
Layout is a critical portion of good power supply design. The following guidelines will help users design a PCB
with the best power conversion performance, thermal performance, and minimized generation of unwanted EMI.
1. The input bypass capacitor CIN must be placed as close as possible to the VIN and PGND pins. Grounding
for both the input and output capacitors should consist of localized top side planes that connect to the PGND
pin and PAD.
2. Place bypass capacitors for VCC close to the VCC pin and ground the bypass capacitor to device ground.
3. Minimize trace length to the FB pin net. Both feedback resistors, RFBT and RFBB should be located close to
the FB pin. Place CFF directly in parallel with RFBT. If VOUT accuracy at the load is important, make sure VOUT
sense is made at the load. Route VOUT sense path away from noisy nodes and preferably through a layer on
the other side of a shielded layer.
4. Use ground plane in one of the middle layers as noise shielding and heat dissipation path.
5. Have a single point ground connection to the plane. The ground connections for the feedback and enable
components should be routed to the ground plane. This prevents any switched or load currents from flowing
in the analog ground traces. If not properly handled, poor grounding can result in degraded load regulation or
erratic output voltage ripple behavior.
6. Make VIN, VOUT and ground bus connections as wide as possible. This reduces any voltage drops on the
input or output paths of the converter and maximizes efficiency.
7. Provide adequate device heat-sinking. Use an array of heat-sinking vias to connect the exposed pad to the
ground plane on the bottom PCB layer. If the PCB has multiple copper layers, these thermal vias can also be
connected to inner layer heat-spreading ground planes. Ensure enough copper area is used for heat-sinking
to keep the junction temperature below 125 °C.
11.2 Compact Layout for EMI Reduction
Radiated EMI is generated by the high di/dt components in pulsing currents in switching converters. The larger
area covered by the path of a pulsing current, the more EMI is generated. High frequency ceramic bypass
capacitors at the input side provide primary path for the high di/dt components of the pulsing current. Placing
ceramic bypass capacitor(s) as close as possible to the VIN and PGND pins is the key to EMI reduction.
The SW pin connecting to the inductor should be as short as possible, and just wide enough to carry the load
current without excessive heating. Short, thick traces or copper pours (shapes) should be used for high current
conduction path to minimize parasitic resistance. The output capacitors should be placed close to the VOUT end
of the inductor and closely grounded to PGND pin and exposed PAD.
The bypass capacitors on VCC should be placed as close as possible to the pin and closely grounded to PGND
and the exposed PAD.
26
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
LMR23630-Q1
www.ti.com
SNVSAR6 – DECEMBER 2016
11.3 Ground Plane and Thermal Considerations
It is recommended to use one of the middle layers as a solid ground plane. Ground plane provides shielding for
sensitive circuits and traces. It also provides a quiet reference potential for the control circuitry. The AGND and
PGND pins should be connected to the ground plane using vias right next to the bypass capacitors. PGND pin is
connected to the source of the internal LS switch. They should be connected directly to the grounds of the input
and output capacitors. The PGND net contains noise at switching frequency and may bounce due to load
variations. PGND trace, as well as VIN and SW traces, should be constrained to one side of the ground plane.
The other side of the ground plane contains much less noise and should be used for sensitive routes.
It is recommended to provide adequate device heat sinking by utilizing the PAD of the IC as the primary thermal
path. Use a minimum 4 by 2 array of 12 mil thermal vias to connect the PAD to the system ground plane heat
sink. The vias should be evenly distributed under the PAD. Use as much copper as possible, for system ground
plane, on the top and bottom layers for the best heat dissipation. Use a four-layer board with the copper
thickness for the four layers, starting from the top of, 2 oz / 1 oz / 1 oz / 2 oz. Four layer boards with enough
copper thickness provides low current conduction impedance, proper shielding and lower thermal resistance.
The thermal characteristics of the LMR23630-Q1 are specified using the parameter θJA, which characterize the
junction temperature of silicon to the ambient temperature in a specific system. Although the value of θJA is
dependent on many variables, it still can be used to approximate the operating junction temperature of the
device. To obtain an estimate of the device junction temperature, one may use the following relationship:
TJ = PD x θJA + TA
(23)
where
TJ = Junction temperature in °C
PD = VIN x IIN x (1 - Efficiency) - 1.1 x IOUT2 x DCR in Watt
DCR = Inductor DC parasitic resistance in Ω
θJA = Junction to ambient thermal resistance of the device in °C/W
TA = Ambient temperature in °C
The maximum operating junction temperature of the LMR23630-Q1 is 125 °C. θJA is highly related to PCB size
and layout, as well as environmental factors such as heat sinking and air flow.
11.4 Feedback Resistors
To reduce noise sensitivity of the output voltage feedback path, it is important to place the resistor divider and
CFF close to the FB pin, rather than close to the load. The FB pin is the input to the error amplifier, so it is a high
impedance node and very sensitive to noise. Placing the resistor divider and CFF closer to the FB pin reduces the
trace length of FB signal and reduces noise coupling. The output node is a low impedance node, so the trace
from VOUT to the resistor divider can be long if short path is not available.
If voltage accuracy at the load is important, make sure voltage sense is made at the load. Doing so will correct
for voltage drops along the traces and provide the best output accuracy. The voltage sense trace from the load to
the feedback resistor divider should be routed away from the SW node path and the inductor to avoid
contaminating the feedback signal with switch noise, while also minimizing the trace length. This is most
important when high value resistors are used to set the output voltage. It is recommended to route the voltage
sense trace and place the resistor divider on a different layer than the inductor and SW node path, such that
there is a ground plane in between the feedback trace and inductor/SW node polygon. This provides further
shielding for the voltage feedback path from EMI noises.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
27
LMR23630-Q1
SNVSAR6 – DECEMBER 2016
www.ti.com
11.5 Layout Example
Output Bypass
Capacitor
Output Inductor
SW
Input Bypass
Capacitor
PGND
BOOT Capacitor
BOOT
VCC
Capacitor
VIN
VCC
AGND
FB
EN/
SYNC
UVLO Adjust Resistor
Output Voltage Set
Resistor
Thermal VIA
VIA (Connect to GND Plane)
Output
Inductor
Output Bypass
Capacitor
BOOT
Capacitor
VCC
Capacitor
SW
PGND
SW
NC
BOOT
VIN
VCC
VIN
FB
EN/SYNC
RT
AGND
Input Bypass
Capacitor
UVLO Adjust
Resistor
RT
Thermal VIA
Output Voltage
Set Resistor
VIA (Connect to GND Plane)
Figure 34. Layout
28
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
LMR23630-Q1
www.ti.com
SNVSAR6 – DECEMBER 2016
12 Device and Documentation Support
12.1 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
12.2 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.3 Trademarks
PowerPAD, E2E are trademarks of Texas Instruments.
SIMPLE SWITCHER is a registered trademark of Texas Instruments.
12.4 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
29
LMR23630-Q1
SNVSAR6 – DECEMBER 2016
www.ti.com
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
30
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
LMR23630-Q1
www.ti.com
SNVSAR6 – DECEMBER 2016
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LMR23630-Q1
31
PACKAGE OPTION ADDENDUM
www.ti.com
9-Dec-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LMR23630AFQDDAQ1
PREVIEW SO PowerPAD
DDA
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
-40 to 125
F30AFQ
LMR23630AFQDDARQ1
PREVIEW SO PowerPAD
DDA
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
-40 to 125
F30AFQ
LMR23630AQDDAQ1
PREVIEW SO PowerPAD
DDA
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
-40 to 125
F30AQ
LMR23630AQDDARQ1
PREVIEW SO PowerPAD
DDA
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
-40 to 125
F30AQ
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
9-Dec-2016
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LMR23630-Q1 :
• Catalog: LMR23630
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
Addendum-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated