MP4209 Silicon N Channel MOS Type (Four L2-π-MOSV in One) TOSHIBA Power MOS FET Module MP4209 Industrial Applications High Power, High Speed Switching Applications For Printer Head Pin Driver and Pulse Motor Driver For Solenoid Driver • 4-V gate drivability • Small package by full molding (SIP 10 pins) • High drain power dissipation (4-device operation) : PT = 4 W (Ta = 25°C) • Low drain-source ON resistance: RDS (ON) = 0.28 Ω (typ.) • High forward transfer admittance: |Yfs| = 3.5 S (typ.) • Low leakage current: IGSS = ±10 μA (max) (VGS = ±16 V) IDSS = 100 μA (max) (VDS = 100 V) • Enhancement-mode: Vth = 0.8 to 2.0 V (VDS = 10 V, ID = 1 mA) Unit: mm Absolute Maximum Ratings (Ta = 25°C) Characteristics Symbol Rating Unit Drain-source voltage VDSS 100 V Drain-gate voltage (RGS = 20 kΩ) VDGR 100 V Gate-source voltage VGSS ±20 V DC ID 3 Pulse IDP 12 Drain power dissipation (1-device operation, Ta = 25°C) PD 2.0 W Drain power dissipation (4device operation, Ta = 25°C) PDT 4.0 W Single pulse avalanche energy (Note 1) EAS 140 mJ Avalanche current IAR 3 A EAR 0.2 EART 0.4 Channel temperature Tch 150 °C Storage temperature range Tstg −55 to 150 °C Drain current - device operation Repetitive avalanche energy (Note 2) 4device operation A JEDEC ― JEITA ― TOSHIBA 2-25A1C Weight: 2.1 g (typ.) mJ Note 1: Condition for avalanche energy (single pulse) measurement VDD = 50 V, starting Tch = 25°C, L = 20 mH, RG = 25 Ω, IAR = 3 A Note 2: Repetitive rating; pulse width limited by maximum channel temperature Note 3: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/Derating Concept and Methods) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). This transistor is an electrostatic-sensitive device. Please handle with caution. 1 2006-10-27 MP4209 Array Configuration 7 9 6 8 10 3 5 4 2 1 Thermal Characteristics Characteristics Thermal resistance from channel to ambient Symbol Max Unit ΣRth (ch-a) 31.2 °C/W TL 260 °C (4-device operation, Ta = 25°C) Maximum lead temperature for soldering purposes (3.2 mm from case for t = 10 s) Electrical Characteristics (Ta = 25°C) Characteristics Symbol Test Condition Min Typ. Max Unit Gate leakage current IGSS VGS = ±16 V, VDS = 0 V ― ― ±10 μA Drain cut-off current IDSS VDS = 100 V, VGS = 0 V ― ― 100 μA Drain-source breakdown voltage Gate threshold voltage V (BR) DSS ID = 10 mA, VGS = 0 V 100 ― ― V Vth VDS = 10 V, ID = 1 mA 0.8 ― 2.0 V VGS = 4 V, ID = 2 A ― 0.36 0.45 VGS = 10 V, ID = 2 A ― 0.28 0.35 VDS = 10 V, ID = 2 A 1.5 3.5 ― S ― 280 ― pF ― 50 ― pF ― 105 ― pF ― 20 ― ― 50 ― Drain-source ON resistance RDS (ON) Forward transfer admittance |Yfs| Input capacitance Ciss Reverse transfer capacitance Crss Output capacitance Coss Rise time VDS = 10 V, VGS = 0 V f = 1 MHz tr ID = 2 A 10 V VGS ton 0V Fall time Turn-off time Total gate charge (gate-source plus gate-drain) 50 Ω Switching time tf toff Qg Gate-source charge Qgs Gate-drain (“miller”) charge Qgd VOUT RL = 25 Ω Turn-on time Ω ns ― 40 ― ― 170 ― ― 13.5 ― nC ― 8.5 ― nC ― 5 ― nC VDD ≈ 50 V VIN: tr, tf < 5 ns, duty ≤ 1%, tw = 10 μs VDD ≈ 80 V, VGS = 10 V ID = 3 A 2 2006-10-27 MP4209 Source-Drain Diode Ratings and Characteristics (Ta = 25°C) Characteristics Symbol Test Condition Min Typ. Max Unit Continuous drain reverse current IDR ― ― ― 3 A Pulse drain reverse current IDRP ― ― ― 12 A Diode forward voltage VDSF IDR = 3 A, VGS = 0 V ― ― −1.5 V Reverse recovery time trr IDR = 3 A, VGS = 0 V ― 100 ― ns Reverse recovery charge Qrr dIDR/dt = 50 A/μs ― 0.2 ― μC Marking MP4209 JAPAN Part No. (or abbreviation code) Lot No. A line indicates lead (Pb)-free package or lead (Pb)-free finish. 3 2006-10-27 MP4209 ID – VDS 2.0 ID – VDS 10 8 Common source 6 Tc = 25°C 4 3 8 10 Drain current ID (A) Drain current ID (A) 1.6 2.8 1.2 2.6 0.8 2.4 0.4 0 0 0.4 0.6 Drain-source voltage 0.8 Common source 6 10 Tc = 25°C 4 6 3.5 4 3 2 VGS = 2.2 V 0.2 8 VGS = 2.5 V 0 0 1.0 VDS (V) 2 4 6 8 Drain-source voltage ID – VGS VDS (V) VDS – VGS 3.2 5 Common source Common source VDS (V) VDS = 10 V 4 3 Drain-source voltage Drain current ID (A) 10 2 25 1 100 Tc = 25°C 2.4 1.6 ID = 5 A 3 0.8 1.5 ) Ta = −55°C 0 0 1 2 3 Gate-source voltage 4 0 0 5 0.8 4 8 Gate-source voltage VGS (V) |Yfs| – ID VDS = 10 V Drain-source ON resistance RDS(ON) (Ω) Forward transfer admittance |Yfs| (S) 20 VGS (V) 3 Common source Ta = −55°C 3 100 25 1 0.5 0.3 0.1 16 RDS (ON) – ID 10 5 12 0.3 0.5 1 3 5 Common source Tc = 25°C 1 0.5 0.3 10 0.1 0.1 10 Drain current ID (A) VGS = 4 V 0.3 0.5 1 3 5 10 Drain current ID (A) 4 2006-10-27 MP4209 RDS (ON) – Tc IDR – VDS (Ω) 1.0 10 (A) Drain-source ON resistance RDS (ON) Common source 0.8 Drain reverse current IDR 1.5 0.8 0.6 ID = 3 A 0.4 3 VGS = 4 V 0.8, 1.5 VGS = 10 V 0.2 5 VGS = 10 V 3 3 1 0.5 1 0 0.3 Common source Tc = 25°C 0 −80 −40 0 40 80 120 0.1 0 160 −0.5 Case temperature Tc (°C) −1.0 −1.5 Drain-source voltage Capacitance – VDS −2.0 VDS (V) Vth – Tc 1000 4 Common source 500 (pF) Gate threshold voltage Coss 100 Capacitance C Vth (V) Ciss 300 50 Crss 30 Common source 10 VGS = 0 V f = 1 MHz 5 Ta = 25°C 3 0.1 0.3 0.5 1 3 5 Drain-source voltage 10 30 50 100 VDS = 10 V 3 ID = 1 mA 2 1 0 −80 VDS (V) −40 0 40 80 120 160 Case temperature Tc (°C) Dynamic Input/Output Characteristics Safe Operating Area 20 100 60 12 40 8 20 0 0 Common source VDD = 80 V ID = 3 A Tc = 25°C VGS 4 8 12 16 4 Drain current ID (A) 16 VGS (V) 80 10 Gate-source voltage Drain-source voltage VDS (V) IDP max VDS 100 μs* 3 1 ms* 1 0.1 1 Total gate charge Qg (nC) *: Single nonrepetitive pulse Tc = 25°C Curves must be derated linearly with increase in temperature. 3 10 30 Drain-source voltage 5 10 ms* 100 ms* 0.3 0 20 ID max 100 300 VDS (V) 2006-10-27 MP4209 Transient thermal resistance rth (°C/W) rth – tw 300 100 30 Curves should be applied in thermal limited area. (Single nonrepetitive pulse) The figure shows thermal resistance per device versus pulse width. (1) (2) 10 -No heat sink/ Attached on a circuit board(1) 1-device operation (2) 2-device operation (3) 3-device operation Circuit board (4) 4-device operation 3 1 0.5 0.001 0.01 0.1 1 Pulse width 10 100 EAS – Tch Avalanche energy EAS (mJ) (W) PDT Total power dissipation 200 (1) 1-device operation (2) 2-device operation (3) 3-device operation (4) 4-device operation Attached on a circuit board 6 (4) Circuit board (3) (2) 2 (1) 0 0 40 80 1000 tw (s) PDT – Ta 8 4 (4) (3) 120 160 160 120 80 40 0 25 200 50 Ambient temperature Ta (°C) 75 100 125 Channel temperature Tch 150 (°C) ΔTch – PDT Channel temperature increase ΔTch (°C) 160 (1) (2) (3) (4) 120 15 V 80 IAR −15 V VDD Circuit board Attached on a circuit board 40 0 0 BVDSS (1) 1-device operation (2) 2-device operation (3) 3-device operation (4) 4-device operation 1 2 3 Total power dissipation 4 PDT TEST CIRCUIT Peak IAR = 3 A, RG = 25 Ω VDD = 50 V, L = 20 mH 5 VDS TEST WAVE FORM ⎞ 1 2 ⎛ B VDSS ⎟ Ε AS = ·L·I · ⎜⎜ ⎟ 2 V − DD ⎠ ⎝ B VDSS (W) 6 2006-10-27 MP4209 RESTRICTIONS ON PRODUCT USE 20070701-EN • The information contained herein is subject to change without notice. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 7 2006-10-27