MUN5135DW1, NSBA123JDXV6, NSBA123JDP6 Dual PNP Bias Resistor Transistors R1 = 2.2 kW, R2 = 47 kW www.onsemi.com PNP Transistors with Monolithic Bias Resistor Network PIN CONNECTIONS This series of digital transistors is designed to replace a single device and its external resistor bias network. The Bias Resistor Transistor (BRT) contains a single transistor with a monolithic bias network consisting of two resistors; a series base resistor and a base−emitter resistor. The BRT eliminates these individual components by integrating them into a single device. The use of a BRT can reduce both system cost and board space. (3) (2) R1 Q2 Features R1 • S and NSV Prefix for Automotive and Other Applications • • • • • (4) (5) 6 0M M G G 0M M G G Unit Collector−Base Voltage VCBO 50 Vdc Collector−Emitter Voltage VCEO 50 Vdc IC 100 mAdc Input Forward Voltage VIN(fwd) 12 Vdc Input Reverse Voltage VIN(rev) 5 Vdc Collector Current − Continuous Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. ORDERING INFORMATION Package Shipping† MUN5135DW1T1G, NSVMUN5135DW1T1G SOT−363 3,000 / Tape & Reel NSBA123JDXV6T5G SOT−563 8,000 / Tape & Reel NSBA123JDP6T5G SOT−963 8,000 / Tape & Reel Device 1 P Max SOT−363 CASE 419B 1 (TA = 25°C, common for Q1 and Q2, unless otherwise noted) Symbol (6) MARKING DIAGRAMS MAXIMUM RATINGS Rating R2 Q1 R2 Requiring Unique Site and Control Change Requirements; AEC-Q101 Qualified and PPAP Capable Simplifies Circuit Design Reduces Board Space Reduces Component Count NSV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q101 Qualified and PPAP Capable These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS Compliant (1) 1 0M/P M G MG G SOT−563 CASE 463A SOT−963 CASE 527AD = Specific Device Code = Date Code* = Pb−Free Package (Note: Microdot may be in either location) *Date Code orientation may vary depending upon manufacturing location. †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. © Semiconductor Components Industries, LLC, 2015 September, 2016 − Rev. 2 1 Publication Order Number: DTA123JD/D MUN5135DW1, NSBA123JDXV6, NSBA123JDP6 THERMAL CHARACTERISTICS Characteristic Symbol Max Unit 187 256 1.5 2.0 mW MUN5135DW1 (SOT−363) One Junction Heated Total Device Dissipation TA = 25°C (Note 1) (Note 2) Derate above 25°C (Note 1) (Note 2) Thermal Resistance, Junction to Ambient PD (Note 1) (Note 2) RqJA mW/°C 670 490 °C/W 250 385 2.0 3.0 mW MUN5135DW1 (SOT−363) Both Junction Heated (Note 3) Total Device Dissipation TA = 25°C (Note 1) (Note 2) Derate above 25°C (Note 1) (Note 2) PD mW/°C (Note 1) (Note 2) RqJA 493 325 °C/W Thermal Resistance, (Note 1) Junction to Lead (Note 2) RqJL 188 208 °C/W TJ, Tstg −55 to +150 °C 357 2.9 mW mW/°C Thermal Resistance, Junction to Ambient Junction and Storage Temperature Range NSBA123JDXV6 (SOT−563) One Junction Heated Total Device Dissipation TA = 25°C (Note 1) Derate above 25°C (Note 1) Thermal Resistance, Junction to Ambient PD RqJA (Note 1) °C/W 350 NSBA123JDXV6 (SOT−563) Both Junction Heated (Note 3) Total Device Dissipation TA = 25°C (Note 1) Derate above 25°C (Note 1) Thermal Resistance, Junction to Ambient PD 500 4.0 RqJA (Note 1) Junction and Storage Temperature Range TJ, Tstg mW mW/°C °C/W 250 −55 to +150 °C 231 269 1.9 2.2 mW NSBA123JDP6 (SOT−963) One Junction Heated Total Device Dissipation TA = 25°C (Note 4) (Note 5) Derate above 25°C (Note 4) (Note 5) Thermal Resistance, Junction to Ambient PD (Note 4) (Note 5) RqJA mW/°C 540 464 °C/W 339 408 2.7 3.3 mW NSBA123JDP6 (SOT−963) Both Junction Heated (Note 3) Total Device Dissipation TA = 25°C (Note 4) (Note 5) Derate above 25°C (Note 4) (Note 5) Thermal Resistance, Junction to Ambient PD (Note 4) (Note 5) Junction and Storage Temperature Range 1. 2. 3. 4. 5. FR−4 @ Minimum Pad. FR−4 @ 1.0 x 1.0 Inch Pad. Both junction heated values assume total power is sum of two equally powered channels. FR−4 @ 100 mm2, 1 oz. copper traces, still air. FR−4 @ 500 mm2, 1 oz. copper traces, still air. www.onsemi.com 2 mW/°C RqJA 369 306 °C/W TJ, Tstg −55 to +150 °C MUN5135DW1, NSBA123JDXV6, NSBA123JDP6 ELECTRICAL CHARACTERISTICS (TA = 25°C, common for Q1 and Q2, unless otherwise noted) Symbol Characteristic Min Typ Max − − 100 − − 500 − − 0.2 50 − − 50 − − 80 140 − − − 0.25 − 0.6 − − 0.8 − − − 0.2 4.9 − − Unit OFF CHARACTERISTICS Collector−Base Cutoff Current (VCB = 50 V, IE = 0) ICBO Collector−Emitter Cutoff Current (VCE = 50 V, IB = 0) ICEO Emitter−Base Cutoff Current (VEB = 6.0 V, IC = 0) IEBO Collector−Base Breakdown Voltage (IC = 10 mA, IE = 0) V(BR)CBO Collector−Emitter Breakdown Voltage (Note 6) (IC = 2.0 mA, IB = 0) V(BR)CEO nAdc nAdc mAdc Vdc Vdc ON CHARACTERISTICS hFE DC Current Gain (Note 6) (IC = 5.0 mA, VCE = 10 V) Collector−Emitter Saturation Voltage (Note 6) (IC = 10 mA, IB = 0.3 mA) VCE(sat) Input Voltage (off) (VCE = 5.0 V, IC = 100 mA) Vi(off) Input Voltage (on) (VCE = 0.2 V, IC = 5.0 mA) Vi(on) Output Voltage (on) (VCC = 5.0 V, VB = 2.5 V, RL = 1.0 kW) VOL Output Voltage (off) (VCC = 5.0 V, VB = 0.5 V, RL = 1.0 kW) VOH Vdc Vdc Vdc Vdc Vdc Input Resistor R1 1.5 2.2 2.9 Resistor Ratio R1/R2 0.038 0.047 0.056 6. Pulsed Condition: Pulse Width = 300 msec, Duty Cycle ≤ 2%. PD, POWER DISSIPATION (mW) 400 350 300 (1) SOT−363; 1.0 x 1.0 inch Pad (2) SOT−563; Minimum Pad (3) SOT−963; 100 mm2, 1 oz. copper trace 250 200 (1) (2) (3) 150 100 50 0 −50 −25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE (°C) Figure 1. Derating Curve www.onsemi.com 3 kW MUN5135DW1, NSBA123JDXV6, NSBA123JDP6 1000 1 IC/IB = 10 25°C 150°C 0.1 −55°C 0.01 0 30 10 20 40 IC, COLLECTOR CURRENT (mA) 100 150°C 1 50 1 10 IC, COLLECTOR CURRENT (mA) 100 Figure 3. DC Current Gain 7 100 5 IC, COLLECTOR CURRENT (mA) f = 10 kHz IE = 0 A TA = 25°C 6 4 3 2 1 150°C −55°C 10 1 25°C 0.1 0.01 VO = 5 V 0.001 0 10 20 30 40 50 0 1 VR, REVERSE BIAS VOLTAGE (V) Figure 4. Output Capacitance 2 3 Vin, INPUT VOLTAGE (V) Figure 5. Output Current vs. Input Voltage 100 Vin, INPUT VOLTAGE (V) Cob, CAPACITANCE (pF) −55°C 10 Figure 2. VCE(sat) vs. IC 0 VCE = 10 V 25°C hFE, DC CURRENT GAIN VCE(sat), COLLECTOR−EMITTER VOLTAGE (V) TYPICAL CHARACTERISTICS MUN5135DW1, NSBA123JDXV6 10 25°C −55°C 1 150°C VO = 0.2 V 0.1 0 40 10 20 30 IC, COLLECTOR CURRENT (mA) Figure 6. Input Voltage vs. Output Current www.onsemi.com 4 50 4 MUN5135DW1, NSBA123JDXV6, NSBA123JDP6 1000 1 VCE = 10 V IC/IB = 10 hFE, DC CURRENT GAIN VCE(sat), COLLECTOR−EMITTER VOLTAGE (V) TYPICAL CHARACTERISTICS NSBA123JDP6 25°C 150°C 0.1 −55°C 0.01 0 10 20 40 30 IC, COLLECTOR CURRENT (mA) 100 −55°C 10 1 50 0.1 1 10 IC, COLLECTOR CURRENT (mA) Figure 7. VCE(sat) vs. IC 100 Figure 8. DC Current Gain 7 100 5 IC, COLLECTOR CURRENT (mA) f = 10 kHz IE = 0 A TA = 25°C 6 4 3 2 1 150°C 10 −55°C 1 25°C 0.1 0.01 VO = 5 V 0.001 0 0 10 20 30 40 VR, REVERSE BIAS VOLTAGE (V) 50 0 Figure 9. Output Capacitance 1 2 Vin, INPUT VOLTAGE (V) Figure 10. Output Current vs. Input Voltage 100 Vin, INPUT VOLTAGE (V) Cob, CAPACITANCE (pF) 150°C 25°C 10 25°C −55°C 1 150°C VO = 0.2 V 0.1 0 10 20 30 40 IC, COLLECTOR CURRENT (mA) Figure 11. Input Voltage vs. Output Current www.onsemi.com 5 50 3 MUN5135DW1, NSBA123JDXV6, NSBA123JDP6 PACKAGE DIMENSIONS SC−88/SC70−6/SOT−363 CASE 419B−02 ISSUE Y 2X aaa H D D H A D 6 5 GAGE PLANE 4 L L2 E1 E 1 2 DETAIL A 3 aaa C 2X bbb H D 2X 3 TIPS NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSIONS D AND E1 DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. MOLD FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT EXCEED 0.20 PER END. 4. DIMENSIONS D AND E1 AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY AND DATUM H. 5. DATUMS A AND B ARE DETERMINED AT DATUM H. 6. DIMENSIONS b AND c APPLY TO THE FLAT SECTION OF THE LEAD BETWEEN 0.08 AND 0.15 FROM THE TIP. 7. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 TOTAL IN EXCESS OF DIMENSION b AT MAXIMUM MATERIAL CONDITION. THE DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OF THE FOOT. e B 6X ddd TOP VIEW DIM A A1 A2 b C D E E1 e L L2 aaa bbb ccc ddd b A2 M C A-B D DETAIL A A 6X ccc C A1 SIDE VIEW C SEATING PLANE c MILLIMETERS MIN NOM MAX −−− −−− 1.10 0.00 −−− 0.10 0.70 0.90 1.00 0.15 0.20 0.25 0.08 0.15 0.22 1.80 2.00 2.20 2.00 2.10 2.20 1.15 1.25 1.35 0.65 BSC 0.26 0.36 0.46 0.15 BSC 0.15 0.30 0.10 0.10 END VIEW RECOMMENDED SOLDERING FOOTPRINT* 6X 6X 0.30 0.66 2.50 0.65 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 6 INCHES NOM MAX −−− 0.043 −−− 0.004 0.035 0.039 0.008 0.010 0.006 0.009 0.078 0.086 0.082 0.086 0.049 0.053 0.026 BSC 0.010 0.014 0.018 0.006 BSC 0.006 0.012 0.004 0.004 MIN −−− 0.000 0.027 0.006 0.003 0.070 0.078 0.045 MUN5135DW1, NSBA123JDXV6, NSBA123JDP6 PACKAGE DIMENSIONS SOT−563, 6 LEAD CASE 463A ISSUE G D −X− 6 5 1 2 A L 4 E −Y− 3 b e NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETERS 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. DIM A b C D E e L HE HE C 5 PL 6 0.08 (0.003) M X Y MILLIMETERS MIN NOM MAX 0.50 0.55 0.60 0.17 0.22 0.27 0.08 0.12 0.18 1.50 1.60 1.70 1.10 1.20 1.30 0.5 BSC 0.10 0.20 0.30 1.50 1.60 1.70 SOLDERING FOOTPRINT* 0.3 0.0118 0.45 0.0177 1.35 0.0531 1.0 0.0394 0.5 0.5 0.0197 0.0197 SCALE 20:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 7 INCHES NOM MAX 0.021 0.023 0.009 0.011 0.005 0.007 0.062 0.066 0.047 0.051 0.02 BSC 0.004 0.008 0.012 0.059 0.062 0.066 MIN 0.020 0.007 0.003 0.059 0.043 MUN5135DW1, NSBA123JDXV6, NSBA123JDP6 PACKAGE DIMENSIONS SOT−963 CASE 527AD ISSUE E D X Y 6 5 4 1 2 3 A HE E C SIDE VIEW TOP VIEW e 6X L NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. DIM A b C D E e HE L L2 MILLIMETERS MIN NOM MAX 0.34 0.37 0.40 0.10 0.15 0.20 0.07 0.12 0.17 0.95 1.00 1.05 0.75 0.80 0.85 0.35 BSC 0.95 1.00 1.05 0.19 REF 0.05 0.10 0.15 RECOMMENDED MOUNTING FOOTPRINT 6X 6X L2 b 6X 0.08 X Y 0.20 BOTTOM VIEW 6X 0.35 PACKAGE OUTLINE 1.20 0.35 PITCH DIMENSIONS: MILLIMETERS ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] ◊ N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 www.onsemi.com 8 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative DTA123JD/D