Agilent ACSL-6xx0 Multi-Channel and Bi-Directional, 15 MBd Digital Logic Gate Optocoupler Data Sheet Features • Available in dual, triple and quad channel configurations • Bi-directional Description ACSL-6xx0 are truly isolated, multi-channel and bi-directional, high-speed optocouplers. Integration of multiple optocouplers in monolithic form is achieved through patented process technology. These devices provide full duplex and bi-directional isolated data transfer and communication capability in compact surface mount packages. Available in 15 Mbd speed option and wide supply voltage range. Applications • Full duplex communication • Wide supply voltage range 3.0V to 5.5V • Isolated line receiver • High-speed: 15 MBd typical, 10 MBd minimum • Computer-peripheral interfaces • Microprocessor system interfaces • 10 kV/µs minimum Common Mode Rejection (CMR) at Vcm = 1000 V • Digital isolation for A/D and D/A conversion • LSTTL/TTL compatible • Switching power supply • Instrument input/output isolation • Ground loop elimination • Pulse transformer replacement These high channel density make them ideally suited to isolating data conversion devices, parallel buses and peripheral interfaces. They are available in 8-pin and 16–pin narrow-body SOIC package and are specified over the temperature range of -40°C to +100° C. • Safety and regulatory approvals (Pending) – 2500Vrms for 1 min per UL1577 – CSA Component Acceptance – IEC/EN/DIN EN 60747-5-2 • 16 Pin narrow-body SOIC package for triple and quad channel • -40 to 100°C temperature range CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation, which may be induced by ESD. Device Selection Guide Device Number Channel Configuration Package ACSL-6210 Dual, Bi-Directional` 8-pin Small Outline ACSL-6300* Triple, All-in-One 16-pin Small Outline ACSL-6310* Triple, Bi-Directional, 2/1 16-pin Small Outline ACSL-6400 Quad, All-in-One 16-pin Small Outline ACSL-6410* Quad, Bi-Directional, 3/1 16-pin Small Outline ACSL-6420* Quad, Bi-Directional, 2/2 16-pin Small Outline * Advanced Information Ordering Information ACSL-6XX0-X Y Z E Lead Free Option Channel Configuration (Refer to the Device Selection Guide) R = SO-8 Package, 100 units per tube T = SO-16 Package, 50 units per tube 6 = IEC/EN/DIN EN 60747-5-2, VIORM = 560V peak Option 5 = Tape and Reel Packaging Option, 1500 units per reel for SO-8 Package and 1000 units per reel for SO-16 Package Pin Description Symbol Description Symbol Description VDD1 Power Supply 1 GND1 Power Supply Ground 1 VDD2 Power Supply 2 GND2 Power Supply Ground 2 ANODEx LED Anode NC Not Connected CATHODEx LED Cathode VOX Output Signal Truth Table (Positive Logic) LED OUTPUT ON L OFF H 2 Functional Diagrams ACSL-6210 - Dual-Ch, Bi-Dir ACSL-6300 - Triple-Ch, All-in-One* ACSL-6310 - Triple-Ch, Bi-Dir (2/1)* ACSL-6400 - Quad-Ch, All-in-One ACSL-6410 - Quad-Ch, Bi-Dir (3/1)* ACSL-6420 - Quad-Ch, Bi-Dir (2/2)* * Advanced Information 3 Package Outline Drawings ACSL-6210 Small Outline SO-8 Package 0.189 (4.80) 0.197 (5.00) 8 7 6 5 0.228 (5.80) 0.244 (6.20) 0.150 (3.80) 0.157 (4.00) 1 2 3 4 0.013 (0.33) 0.020 (0.51) 0.010 (0.25) 0.020 (0.50) x 45° 0.008 (0.19) 0.010 (0.25) 0.004 (0.10) 0.010 (0.25) 0.054 (1.37) 0.069 (1.75) 0° 8° 0.040 (1.016) 0.060 (1.524) 0.016 (0.40) 0.050 (1.27) DIMENSIONS: INCHES (MILLIMETERS) MIN MAX ACSL-6300*, ACSL-6310*, ACSL-6400, ACSL-6410* and ACSL-6420* Small Outline SO-16 Package 0.386 (9.802) 0.394 (9.999) 8 1 0.228 (5.791) 0.244 (6.197) 0.152 (3.861) 0.157 (3.988) 0.013 (0.330) 0.020 (0.508) 0.054 (1.372) 0.068 (1.727) 0.050 (1.270) 0.060 (1.524) 0.010 (0.245) x 45°ß 0.020 (0.508) 0° – 8° TYP 0.040 (1.016) 0.060 (1.524) DIMENSIONS: INCHES (MIL LIMETERS) MIN MAX 4 0.008 (0.191) 0.010 (0.249) 0.004 (0.102) 0.010 (0.249) 0.016 (0.406) 0.050 (1.270) Solder Reflow Temperature Profile 300 PREHEATING RATE 3°C + 1°C/–0.5°C/SEC. REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC. PEAK TEMP. 240°C PEAK TEMP. 230°C 200 TEMPERATURE (°C) PEAK TEMP. 245°C 2.5°C ± 0.5°C/SEC. 30 SEC. 160°C 150°C 140°C SOLDERING TIME 200°C 30 SEC. 3°C + 1°C/–0.5°C 100 PREHEATING TIME 150°C, 90 ± 30 SEC. 50 SEC. TIGHT TYPICAL LOOSE ROOM TEMPERATURE 0 0 50 100 TIME (SECONDS) Pb-free IR Profile 5 150 200 250 Regulatory Information Insulation and Safety Related Specifications Parameter Symbol Value Units Conditions Minimum External Air Gap (Clearance) L(I01) 4.9 mm Measured from input terminals to output terminals, shortest distance through air Minimum Externa l Tracking(Creepage) L(I02) 4.5 mm Measured from input terminals to output terminals, shortest distance path through body Minimum Internal Plastic Gap (Internal Clearance) 0.08 mm Insulation thickness between emitter and detector; also known as distance through insulation Tracking Resistance (Comparative Tracking Index) CTI 175 Volts DIN IEC 112/VDE0303 Part 1 Isolation Group IIIa Material Group (DIN VDE 0110, 1/89, Table 1) IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (Option X6X Only) Description Symbol ACSL-6XX0-X6X Installation Classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤ 150V rms for rated mains voltage ≤ 300V rms I-IV I-III Climatic Classification 55/100/21 Pollution Degree (DIN VDE 0110/1.89) 2 Units Maximum Working Insulation Voltage VIORM 560 Vpeak Input to Output Test Voltage, Method b * VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, Partial Discharge < 5 pC VPR 1050 Vpeak Input to Output Test Voltage, Method a * VIORM x 1.5 = VPR, Type and Sample Test, Tm = 60 sec, Partial Discharge < 5 pC VPR 840 Vpeak Highest Allowable Overvoltage * (Transient Overvoltage, tini = 10 sec) VIOTM 4000 Vpeak Safety Limiting Values (Maximum values allowed in the event of a failure) Case Temperature Input Current Output Power TS IS,INPUT PS,OUTPUT 175 150 600 °C mA mW Insulation Resistance at TS, VIO = 500V RIO 109 Ω *Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section, IEC/EN/DIN EN 60747-5-2, for a detailed description. Note: Isolation characteristics are guaranteed only within the safety maximum ratings, which must be ensured by protective circuits in application. 6 Absolute Maximum Ratings Parameter Symbol Min. Max. Units Storage Temperature Ts -55 125 °C Operating Temperature TA -40 100 °C Supply Voltage (1 Minute Maximum) VDD1 , VDD2 7 V Reverse Input Voltage (Per Channel) VR 5 V Output Voltage (Per Channel) VO 7 V Average Forward Input Current [1] (Per Channel) IF 15 mA Output Current (Per Channel) IO 50 mA Input Power Dissipation[2] (Per Channel) P1 27 mW Output Power Dissipation [2] (Per Channel) PO 60 mW Recommended Operating Conditions Parameter Symbol Min. Max. Units Operating Temperature TA -40 100 °C Input Current, Low Level [3] IFL 0 250 µA Input Current, High Level [4] IFH 7 15 mA Supply Voltage VDD1, VDD2 3.0 5.5 V Fan Out (at TA= 1kΩ) N 5 TTL Loads Output Pull-up Resistor RL 4k Ω Notes: 1. Peaking circuits may produce transient input currents up to 50 mA, 50 ns max. pulse width, provided average current does not exceed its max. values. 2. Derate total package power dissipation, PT linearly above +80°C free-air temperature at a rate of 5.45 mW/°C for the SO8 package. PT=number of channels multiply by (PI+PO). For SO16 package data, contact factory for assistance. 7 330 3. The off condition can be guaranteed by ensuring that VFL ≤ 0.8V. 4. The initial switching threshold is 7 mA or less. It is recommended that minimum 8 mA be used for best performance and to permit guardband for LED degradation. Electrical Specifications Over recommended operating range (3.0V ≤ VDD1 ≤ 3.6V, 3.0V ≤ VDD2 ≤ 3.6V, TA = -40°C to +100° C) unless otherwise specified. All typical specifications are at TA = +25°C , VDD1 = VDD2 = +3.3V. Parameter Symbol Input Threshold Current Min. Typ. Max. Units Test Conditions ITH 2.7 7.0 mA IOL(Sinking)=13 mA, VO = 0.6V High Level Output Current IOH 4.7 100.0 µA IF = 250 µA, VO = 3.3V Low Level Output Voltage VOL 0.36 0.68 V IOL(Sinking) = 13 mA, IF = 7mA High Level Supply Current (per channel) IDDH 3.2 5.0 mA IF = 0 mA Low Level Supply Current (per channel) IDDL 4.6 7.5 mA IF = 10 mA Input Forward Voltage VF 1.25 1.52 1.80 V IF = 10 mA, TA = 25°C Input Reverse Breakdown Voltage BVR 5.0 V IR = 10 µA Input Diode Temperature Coefficient ∆VF / ∆TA -1.8 mV/°C IF = 10 mA Input Capacitance CIN 80 pF f = 1 MHz, VF = 0V Switching Specifications Over recommended operating range (3.0V ≤ VDD1 ≤ 3.6V, 3.0V ≤ VDD2 ≤ 3.6V, IF = 8.0 mA, TA = -40° C to +100° C) unless otherwise specified. All typical specifications are at TA = +25°C , VDD1 = VDD2 = +3.3V. Parameter Symbol Maximum Data Rate Pulse Width tPW Propagation Delay Time to Logic High Output Level [5] tPLH Propagation Delay Time to Logic Low Output Level [6] Pulse Width Distortion |tPHL – tPLH| Propagation Delay Skew[7] tPSK Output Rise Time (10 – 90%) tR Output Fall Time (10 – 90%) tF Logic High Common Mode Transient Immunity [8] |CMH| Logic Low Common Mode Transient Immunity [8] |CML| Min. Typ. 10 15 Max. 100 6. tPHL is measured from the 4.0 mA level on the rising edge of the input pulse to the 1.5V level on the falling edge of the output pulse. 7. tPSK is equal to the worst case difference in tPHL and/or tPLH that will be seen between units at any given temperature and specified test conditions. 8 Test Conditions MBd RL = 350Ω, CL = 15 pF ns RL = 350Ω, CL = 15 pF RL = 350Ω, CL = 15 pF 52 100 ns tPHL 44 100 ns RL = 350Ω, CL = 15 pF |PWD| 8 35 ns RL = 350Ω, CL = 15 pF 40 ns RL = 350Ω, CL = 15 pF 35 ns RL = 350Ω, CL = 15 pF 12 ns RL = 350Ω, CL = 15 pF 10 kV/µs Vcm = 1000V, IF = 0 mA, VO = 2.0V, RL = 350Ω, TA = 25°C 10 kV/µs Vcm = 1000V, IF = 8 mA, VO = 0.8V, RL = 350Ω, TA = 25°C Notes: 5. tPLH is measured from the 4.0 mA level on the falling edge of the input pulse to the 1.5V level on the rising edge of the output pulse. Units 8. CMH is the maximum common mode voltage slew rate that can be sustained while maintaining VO > 2.0V. CML is the maximum common mode voltage slew rate that can be sustained while maintaining VO < 0.8V. The common mode voltage slew rates apply to both rising and falling common mode voltage edges. Electrical Specifications Over recommended operating range (4.5V ≤ VDD1 ≤ 5.5V, 4.5V ≤ VDD2 ≤ 5.5V, TA = -40°C to +100° C) unless otherwise specified. All typical specifications are at TA = +25°C, VDD1 = VDD2 = +5.0V. Parameter Symbol Input Threshold Current Min. Typ. Max. Units Test Conditions ITH 2.7 7.0 mA IOL(Sinking)=13 mA, VO= 0.6V High Level Output Current IOH 3.8 100.0 µA IF = 250 µA, VO= 5.5V Low Level Output Voltage VOL 0.36 0.6 V IOL(Sinking)=13 mA, IF=7 mA High Level Supply Current (per channel) IDDH 4.3 7.5 mA IF = 0 mA Low Level Supply Current (per channel) IDDL 5.8 10.5 mA IF = 10 mA Input Forward Voltage VF 1.25 1.52 1.8 V IF = 10 mA, TA = 25°C Input Reverse Breakdown Voltage BVR 5.0 V IR = 10 µA Input Diode Temperature Coefficient ∆VF / ∆TA -1.8 mV/°C IF = 10 mA Input Capacitance CIN 80 pF f = 1 MHz, VF = 0 V Switching Specifications Over recommended operating range (4.5V ≤ VDD1 ≤ 5.5V, 4.5V ≤ VDD2 ≤ 5.5V, IF = 8.0 mA, TA = -40° C to +100° C) unless otherwise specified. All typical specifications are at TA=+25° C, VDD1 = VDD2 = +5.0V. Parameter Symbol Maximum Data Rate Pulse Width tPW Propagation Delay Time to Logic High Output Level[5] tPLH Propagation Delay Time to Logic Low Output Level[6] Pulse Width Distortion |tPHL – tPLH| Propagation Delay Skew[7] tPSK Output Rise Time (10 – 90%) tR Output Fall Time (10 – 90%) tF Logic High Common Mode Transient Immunity [8] |CMH| Logic Low Common Mode Transient Immunity [8] |CML| Min. Typ. 10 15 Max. 100 6. tPHL is measured from the 4.0 mA level on the rising edge of the input pulse to the 1.5V level on the falling edge of the output pulse. 7. tPSK is equal to the worst case difference in tPHL and/or tPLH that will be seen between units at any given temperature and specified test conditions. 9 Test Conditions MBd RL = 350Ω, CL =15 pF ns RL = 350Ω, CL =15 pF RL = 350Ω, CL =15 pF 46 100 ns tPHL 43 100 ns RL = 350Ω, CL =15 pF |PWD| 5 35 ns RL = 350Ω, CL =15 pF 40 ns RL = 350Ω, CL =15 pF 30 ns RL = 350Ω, CL =15 pF 12 ns RL = 350Ω, CL =15 pF 10 kV/µs Vcm= 1000V, IF=0 mA, VO = 2.0V, RL=350Ω, TA = 25°C 10 kV/µs Vcm= 1000V, IF= 8 mA, VO = 0.8V, RL= 350Ω, TA = 25°C Notes: 5. tPLH is measured from the 4.0 mA level on the falling edge of the input pulse to the 1.5V level on the rising edge of the output pulse. Units 8. CMH is the maximum common mode voltage slew rate that can be sustained while maintaining VO > 2.0V. CML is the maximum common mode voltage slew rate that can be sustained while maintaining VO < 0.8V. The common mode voltage slew rates apply to both rising and falling common mode voltage edges. Package Characteristics All specifications are at TA=+25°C. Parameter Symbol Min. 2500 2500 Typ. Max. Units Test Conditions VRMS RH ≤ 50%, t = 1 min RH ≤ 50%, t = 1 min µA 45% RH, t=5 sec, VI-O= 3kV DC 45% RH, t=5 sec, VI-O =3kV DC 1011 1011 Ω VI-O = 500V DC VI-O = 500V DC Input-Output Momentary Withstand Voltage[9] SO8 SO16 VISO VISO Input-Output Insulation [10] [11] SO8 SO16 II-O II-O Input-Output Resistance[10] SO8 SO16 RI-O RI-O Input-Output Capacitance[10] SO8 SO16 CI-O CI-O 0.7 0.7 pF f = 1 MHz f = 1 MHz Input-Input Insulation Leakage Current[12] SO8 SO16 II-I II-I 0.005 0.005 µA RH ≤ 45%, t = 5 sec, VI-I = 500V RH ≤ 45%, t = 5 sec, VI-I = 500V Input-Input Resistance[12] SO8 SO16 RI-I RI-I 1011 1011 Ω RH ≤ 45%, t= 5 sec, VI-I = 500V RH ≤ 45%, t =5 sec, VI-I =500V Input-Input Capacitance[12] SO8 SO16 CI-I CI-I 0.1 0.12 pF f = 1 MHz f = 1 MHz Electrostatic Discharge Sensitivity This product has been tested for electrostatic sensitivity to the limits stated in the specifications. However, Agilent recommends that all integrated circuits be handled with appropriate care to avoid damage. Damage caused by inappropriate handling or storage could range from performance degradation to complete failure. www.agilent.com/semiconductors For product information and a complete list of distributors, please go to our web site. For technical assistance call: Americas/Canada: +1 (800) 235-0312 or (916) 788-6763 Europe: +49 (0) 6441 92460 China: 10800 650 0017 Hong Kong: (65) 6756 2394 India, Australia, New Zealand: (65) 6755 1939 Japan: (+81 3) 3335-8152(Domestic/International), or 0120-61-1280(Domestic Only) Korea: (65) 6755 1989 Singapore, Malaysia, Vietnam, Thailand, Philippines, Indonesia: (65) 6755 2044 Taiwan: (65) 6755 1843 Data subject to change. Copyright © 2004 Agilent Technologies, Inc. November 1, 2004 5989-1343EN 5 5 109 109 Notes: 9. VISO is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For continuous voltage rating, refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), the equipment level safety specification or Agilent Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage.” 10. Measured between each input pair shorted together and all output connections for that channel shorted together. 11. In accordance to UL1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 3000 Vrms for 1 sec (leakage detection current limit, II-O ≤ 5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table, if applicable. 12. Measured between inputs with the LED anode and cathode shorted together.