1.27mm Pitch Connector FX1 Series DIN duplex density mount has been achieved. (DIN 96 contacts and FX1 192 (96x2) Photo 1 ■Features 1. High density and space saved-DIN Duplex Mount Achieved Sequence Structure (Pin contact sequence) Figure 2 The alignment of the mating area in 4-row allows to duplex the number of contacts in the nearly equivalent mount square as for the conventional DIN connector.(Refer to photo (1).) 2. High Current and High Voltage Two-thirds of total contact numbers are used for half pitch signaling contact, while the other one-third thereof is used for the power ground contact. Power ground contact corresponds to high current (1A) and high voltage (250V). 3. Sequence Structure Considering insertion/extraction in active power mode and maintenance on the end user side, the FX series is designed in a mechanism that can afford the time different contact at three steps. (For details, refer to Figure (2) as shown on the right.) FX1V (3 step sequence) Mating Power Supply Ground Signal Removal 4. Mis-insertion Prevent Provide the insertion guide on both ends of connector, and widen an inductive area in order to prevent mis-insertion. *FX1 Series (2 step sequence) 1 Row B 2 Row A, row C *FX1 Series (3 step sequence) 1 B1 to B4, B45 to B52, B93 to B96 2 B5 to B44, B53 to B92 3 Row A, row C Setting row B to ground, if active cable insertion and extraction are performed as power supply, arc will occur between contact and contact. The row B contact structure is constructed to separate arc occurrence point a and normal contact point b, and minimizes affects on the contact. A134 ■Product Specifications Current rating Voltage rating 0.5A Signal Contact: 125V AC Operating Temperature Range-55 to 85ç (Note 1) Storage Temperature Range -10 to +60ç(Note 2) Rating Signal Contact: Power Supply Contact: 1A Power Supply Contact: 250V AC Operating Humidity Range -40 to 80% Operating Humidity Range -40 to 70% (Note 2) Item Specification Condition 1000M ohms min. 250V DC 2. Withstanding Voltage No flashover or insulation breakdown. 1 minute 3. Contact Resistance 60m ohms max. (conductor resistance included) 100mA 4. Vibration No electrical discontinuity of 1µs or more Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions. 5. Humidity (Steady state) Contact resistance: 70m ohms max. Insulation resistance: 1000M ohms min. 96 hours at temperature of 40ç and humidity of 90% to 95% 6. Temperature Cycle Contact resistance: 70m ohms max. Insulation resistance: 1000M ohms min. (-55ç: 30 minutes→15- to 35ç: 5 minutes max.→ (-85ç: 30 minutes→15- to 35ç: 5 minutes max.) 5 cycles 1. Insulation Resistance 7. Durability (Mating/un-mating) Contact resistance: 70 m ohms max. Signal contact Power supply contact 300V AC 600V AC 500 cycles Note 1: Includes temperature rise caused by current flow. Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non conducting condition of installed connectors in storage, shipment or during transportation. ■Material ●FX1 Series Parts Insulator Contact Header Receptacle Material Finish Remarks PPS PPS/ PTB Black UL94V-0 Straight header Brass Right angle header Phosphor bronze Phosphor bronze Receptacle Prefixed pin Contact area:Gold plated Lead area:Tin-lead plated ________ Phosphor bronze Tin-lead plated ________ Material Finish Remarks LCP PPS/ PTB Black UL94V-0 ●FXV Series Parts Insulator Header Receptacle Contact Phosphor bronze Prefixed pin Phosphor bronze Contact area:Gold plated Lead area:Tin-lead plated Tin-lead plated ________ ________ A135 ■Ordering Information ●FX1 Series FX1 - 192 P - 1.27 DSA L q q Series Name w e r t y r Contact pitch: 1.27mm : FX1 w Number of contacts: 192, 216 t Contact type: DS : Right angle e Connector type : P-header DSA : Straight y L: Board prefixed pin : S-receptacle Note: The cleaning type only is applied on the header side to FX1 series. ●FX1V Series FX1V q q Series Name A - 192 P - DSA L w : FX1V w A: Cleaning type (header side only) Blank: No cleaning type e Number of contacts : 288 e r t y r Connector type: P-header S-receptacle t Contact type: DS : Right angle DSA : Straight y L: Board prefixed pin Note 1. Cleaning type: the liquid escape hole is added at dip cleaning. No cleaning type: no liquid escape hole is added at dip cleaning. Note 2. The FX1V series omits the contact pitch. BApplication Pattern A136 FX1 Series ■Receptacle : Right Angle Type BPCB mounting pattern Applicable board thickness t=1.6mm Unit: mm Part Number CL No. FX1-144S-1.27DS 571-0003-7 FX1-144S-1.27DSL 571-0053-5 FX1-192S-1.27DS 571-0004-0 FX1-192S-1.27DSL 571-0054-8 FX1-216S-1.27DS 571-0005-2 FX1-216S-1.27DSL 571-0055-0 Number of Contacts A B C 144 73.29 68.08 59.69 192 93.61 88.4 80.01 216 103.77 98.56 90.17 D ____ 67.31 ____ 87.63 ____ 97.79 A137 ■Header : Straight Type BPCB mounting pattern Applicable board thickness t=1.6mm Unit: mm Part Number A138 CL No. FX1-144P-1.27DSA 571-0303-0 FX1-144P-1.27DSAL 571-0353-9 FX1-192P-1.27DSA 571-0304-3 FX1-192P-1.27DSAL 571-0354-1 FX1-216P-1.27DSA 571-0305-6 FX1-216P-1.27DSAL 571-0355-4 Number of Contacts A B 144 73.29 59.69 192 93.61 80.01 216 103.77 90.17 D ____ 69.85 ____ 90.17 ____ 100.33 ■Header : Right Angle Type BPCB mounting pattern Applicable board thickness t=1.6mm Part Number CL No. FX1-144P-1.27DS 571-0203-6 FX1-144P-1.27DSL 571-0253-4 Number of Contacts 144 A139 FX1V Series ■Receptacle : Right Angle Type BPCB mounting pattern Recommended board thickness t=1.6mm (lead length: 3mm) Part Number CL No. FX1V-288S-DS 571-0606-2 FX1V-288S-DSL 571-0656-0 ■Header : Straight Type Liquid escape hole With hole : Cleaning type Without hole : No Cleaning type BPCB mounting pattern Recommended board thickness t=1.6mm (lead length: 3.4mm) Part Number A140 CL No. FX1V-288P-DSA 571-0906-6 FX1V-288P-DSAL 571-0956-4 FX1VA-288P-DSA 571-1006-0 FX1VA-288P-DSAL 571-1056-9 BPrecautions 1. Soldering (1)In the case of manual soldering, complete services under the condition of soldering iron bit temperature below 300ç for 2 seconds max. Please be sure to coat the contacts with solder so that no force is given. (2)In the case of dip soldering bath, complete service under the condition of soldering iron bit temperature below 260ç for 5 seconds max. 2. Prefixed function If the prefixed function is required, please use to the board prefixed pin type. A141