AD AD8131 Low cost, high speed differential driver Datasheet

Low Cost, High Speed
Differential Driver
AD8131
FUNCTIONAL BLOCK DIAGRAM
High speed
400 MHz, −3 dB full power bandwidth
2000 V/μs slew rate
Fixed gain of 2 with no external components
Internal common-mode feedback to improve gain and phase
balance: −60 dB @ 10 MHz
Separate input to set the common-mode output voltage
Low distortion: 68 dB SFDR @ 5 MHz 200 Ω load
Power supply range +2.7 V to ±5 V
–DIN 1
750Ω
750Ω
VOCM 2
V+ 3
8 +DIN
7 NC
1.5kΩ
1.5kΩ
+OUT 4
6 V–
5 –OUT
AD8131
NC = NO CONNECT
01072-001
FEATURES
Figure 1.
APPLICATIONS
Video line driver
Digital line driver
Low power differential ADC driver
Differential in/out level shifting
Single-ended input to differential output driver
GENERAL DESCRIPTION
The AD8131 can replace transformers in a variety of applications,
preserving low frequency and dc information. The AD8131 does
not have the susceptibility to magnetic interference and hysteresis
of transformers. It is smaller, easier to work with, and has the high
reliability associated with ICs.
ΔVOUT, dm = 2V p-p
ΔVOUT, cm/ΔVOUT, dm
–30
–40
–50
VS = +5V
–60
–70
VS = ±5V
01072-002
The AD8131 is a differential driver for the transmission of
high-speed signals over low-cost twisted pair or coax cables.
The AD8131 can be used for either analog or digital video
signals or for other high-speed data transmission. The AD8131
driver is capable of driving either Cat3 or Cat5 twisted pair or
coax with minimal line attenuation. The AD8131 has
considerable cost and performance improvements over discrete
line driver solutions.
–20
BALANCE ERROR (dB)
The AD8131 is a differential or single-ended input to
differential output driver requiring no external components for
a fixed gain of 2. The AD8131 is a major advancement over op
amps for driving signals over long lines or for driving
differential input ADCs. The AD8131 has a unique internal
feedback feature that provides output gain and phase matching
that are balanced to −60 dB at 10 MHz, reducing radiated EMI
and suppressing harmonics. Manufactured on the Analog
Devices, Inc. next generation XFCB bipolar process, the
AD8131 has a −3 dB bandwidth of 400 MHz and delivers a
differential signal with very low harmonic distortion.
–80
1
10
100
FREQUENCY (MHz)
1000
Figure 2. Output Balance Error vs. Frequency
The AD8131’s differential output also helps balance the input
for differential ADCs, optimizing the distortion performance of
the ADCs. The common-mode level of the differential output is
adjustable by a voltage on the VOCM pin, easily level-shifting the
input signals for driving single-supply ADCs with dual supply
signals. Fast overload recovery preserves sampling accuracy.
The AD8131 is available in both SOIC and MSOP packages for
operation over −40°C to +125°C.
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2005 Analog Devices, Inc. All rights reserved.
Powered by TCPDF (www.tcpdf.org)
IMPORTANT LINKS for the AD8131*
Last content update 08/23/2013 05:36 pm
PARAMETRIC SELECTION TABLES
Find Similar Products By Operating Parameters
Amplifiers for Video Distribution
High Speed Amplifiers Selection Table
DESIGN COLLABORATION COMMUNITY
Collaborate Online with the ADI support team and other designers
about select ADI products.
Follow us on Twitter: www.twitter.com/ADI_News
Like us on Facebook: www.facebook.com/AnalogDevicesInc
DOCUMENTATION
AN-692: Universal Precision Op Amp Evaluation Board
AN-649: Using the Analog Devices Active Filter Design Tool
AN-357: Operational Integrators
AN-356: User’s Guide to Applying and Measuring Operational
Amplifier Specifications
AN-584: Using the AD813X Differential Amplifier
Video Amplifier Products
UG-474: Evaluation Board for Differential Amplifiers Offered in 8-Lead
SOIC Packages
UG-130: Differential Amplifier Evaluation Board for 8-lead SOIC and
MSOP Packages
Video Amplifier Products
Security and Surveillance Applications Booklet
Security and Surveillance Applications Technical Presentation
DESIGN TOOLS, MODELS, DRIVERS & SOFTWARE
Analog Filter Wizard 2.0
AD8131 SPICE Macro-Model Maximum Values
AD8131 SPICE Macro-Model Typical Values
DESIGN SUPPORT
Submit your support request here:
Linear and Data Converters
Embedded Processing and DSP
Telephone our Customer Interaction Centers toll free:
Americas:
Europe:
China:
India:
Russia:
1-800-262-5643
00800-266-822-82
4006-100-006
1800-419-0108
8-800-555-45-90
Quality and Reliability
Lead(Pb)-Free Data
SAMPLE & BUY
AD8131
View Price & Packaging
Request Evaluation Board
Request Samples
Check Inventory & Purchase
Find Local Distributors
EVALUATION KITS & SYMBOLS & FOOTPRINTS
View the Evaluation Boards and Kits page for the AD8131
View the Evaluation Boards and Kits page for the AD8330
Symbols and Footprints
* This page was dynamically generated by Analog Devices, Inc. and inserted into this data sheet.
Note: Dynamic changes to the content on this page (labeled 'Important Links') does not
constitute a change to the revision number of the product data sheet.
This content may be frequently modified.
AD8131
TABLE OF CONTENTS
Specifications..................................................................................... 3
Estimating the Output Noise Voltage ...................................... 16
±DIN to ±OUT Specifications...................................................... 3
Calculating the Input Impedance of an
Application Circuit..................................................................... 16
VOCM to ±OUT Specifications ..................................................... 4
±DIN to ±OUT Specifications...................................................... 5
Input Common-Mode Voltage Range in
Single-Supply Applications ....................................................... 17
VOCM to ±OUT Specifications ..................................................... 6
Setting the Output Common-Mode Voltage .......................... 17
Absolute Maximum Ratings............................................................ 7
Driving a Capacitive Load......................................................... 17
ESD Caution.................................................................................. 7
Applications..................................................................................... 18
Pin Configuration and Function Descriptions............................. 8
Twisted-Pair Line Driver........................................................... 18
Typical Performance Characteristics ............................................. 9
3 V Supply Differential A-to-D Driver.................................... 18
Operational Description................................................................ 15
Unity-Gain, Single-Ended-to-Differential Driver ................. 19
Theory of Operation ...................................................................... 16
Outline Dimensions ....................................................................... 20
Analyzing an Application Circuit............................................. 16
Ordering Guide .......................................................................... 20
Closed-Loop Gain ...................................................................... 16
REVISION HISTORY
6/05—Rev. A to Rev. B
Updated Format..................................................................Universal
Changed Upper Operating Limit .....................................Universal
Changes to Ordering Guide .......................................................... 20
Rev. B | Page 2 of 20
AD8131
SPECIFICATIONS
±DIN TO ±OUT SPECIFICATIONS
25°C, VS = ±5 V, VOCM = 0 V, G = 2, RL, dm = 200 Ω, unless otherwise noted. Refer to Figure 5 and Figure 39 for test setup and label
descriptions. All specifications refer to single-ended input and differential outputs, unless otherwise noted.
Table 1.
Parameter
DYNAMIC PERFORMANCE
−3 dB Large Signal Bandwidth
−3 dB Small Signal Bandwidth
Bandwidth for 0.1 dB Flatness
Slew Rate
Settling Time
Overdrive Recovery Time
NOISE/HARMONIC PERFORMANCE
Second Harmonic
Third Harmonic
IMD
IP3
Voltage Noise (RTO)
Differential Gain Error
Differential Phase Error
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage
CMRR
OUTPUT CHARACTERISTICS
Offset Voltage (RTO)
Output Voltage Swing
Linear Output Current
Gain
Output Balance Error
Conditions
Min
Typ
Max
Unit
VOUT = 2 V p-p
VOUT = 0.2 V p-p
VOUT = 0.2 V p-p
VOUT = 2 V p-p, 10% to 90%
0.1%, VOUT = 2 V p-p
VIN = 5 V to 0 V Step
400
320
85
2000
14
5
MHz
MHz
MHz
V/μs
ns
ns
VOUT = 2 V p-p, 5 MHz, RL, dm = 200 Ω
VOUT = 2 V p-p, 20 MHz, RL, dm = 200 Ω
VOUT = 2 V p-p, 5 MHz, RL, dm = 800 Ω
VOUT = 2 V p-p, 20 MHz, RL, dm = 800 Ω
VOUT = 2 V p-p, 5 MHz, RL, dm = 200 Ω
VOUT = 2 V p-p, 20 MHz, RL, dm = 200 Ω
VOUT = 2 V p-p, 5 MHz, RL, dm = 800 Ω
VOUT = 2 V p-p, 20 MHz, RL, dm = 800 Ω
20 MHz, RL, dm = 800 Ω
20 MHz, RL, dm = 800 Ω
f = 20 MHz
NTSC, RL, dm = 150 Ω
NTSC, RL, dm = 150 Ω
−68
−63
−95
−79
−94
−70
−101
−77
−54
30
25
0.01
0.06
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBm
nV/√Hz
%
degrees
Single-ended input
Differential input
1.125
1.5
1
−7.0 to +5.0
−70
kΩ
kΩ
pF
V
dB
ΔVOUT, dm/ΔVIN, cm; ΔVIN, cm = ±0.5 V
VOS, dm = VOUT, dm; VDIN+ = VDIN− = VOCM = 0 V
TMIN to TMAX variation
VOCM = float
TMIN to TMAX variation
Maximum ΔVOUT; single-ended output
ΔVOUT, dm/ΔVIN, dm; ΔVIN, dm = ±0.5 V
ΔVOUT, cm/ΔVOUT, dm; ΔVOUT, dm = 1 V
Rev. B | Page 3 of 20
1.97
±2
±8
±4
±10
−3.6 to +3.6
60
2
−70
±7
2.03
mV
μV/°C
mV
μV/°C
V
mA
V/V
dB
AD8131
VOCM TO ±OUT SPECIFICATIONS
25°C, VS = ±5 V, VOCM = 0 V, G = 2, RL, dm = 200 Ω, unless otherwise noted. Refer to Figure 5 and Figure 39 for test setup and label
descriptions. All specifications refer to single-ended input and differential outputs, unless otherwise noted.
Table 2.
Parameter
DYNAMIC PERFORMANCE
−3 dB Bandwidth
Slew Rate
DC PERFORMANCE
Input Voltage Range
Input Resistance
Input Offset Voltage
Input Bias Current
VOCM CMRR
Gain
POWER SUPPLY
Operating Range
Quiescent Current
Power Supply Rejection Ratio
OPERATING TEMPERATURE RANGE
Conditions
Min
ΔVOCM = 600 mV
VOCM = −1 V to +1 V
VOS, cm = VOUT, cm; VDIN+ = VDIN− = VOCM = 0 V
VOCM = float
ΔVOUT, dm/ΔVOCM; ΔVOCM = ±0.5 V
ΔVOUT, cm/ΔVOCM; ΔVOCM = ±1 V
VDIN+ = VDIN− = VOCM = 0 V
TMIN to TMAX variation
ΔVOUT, dm/ΔVS; ΔVS = ±1 V
0.988
±1.4
10.5
−40
Rev. B | Page 4 of 20
Typ
Max
Unit
210
500
MHz
V/μs
±3.6
120
±1.5
±2.5
0.5
−60
1
V
kΩ
mV
mV
μA
dB
V/V
11.5
25
−70
±7
1.012
± 5.5
12.5
−56
+125
V
mA
μA/°C
dB
°C
AD8131
±DIN TO ±OUT SPECIFICATIONS
25°C, VS = 5 V, VOCM = 2.5 V, G = 2, RL, dm = 200 Ω, unless otherwise noted. Refer to Figure 5 and Figure 39 for test setup and label
descriptions. All specifications refer to single-ended input and differential outputs, unless otherwise noted.
Table 3.
Parameter
DYNAMIC PERFORMANCE
−3 dB Large Signal Bandwidth
−3 dB Small Signal Bandwidth
Bandwidth for 0.1 dB Flatness
Slew Rate
Settling Time
Overdrive Recovery Time
NOISE/HARMONIC PERFORMANCE
Second Harmonic
Third Harmonic
IMD
IP3
Voltage Noise (RTO)
Differential Gain Error
Differential Phase Error
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage
CMRR
OUTPUT CHARACTERISTICS
Offset Voltage (RTO)
Output Voltage Swing
Linear Output Current
Gain
Output Balance Error
Conditions
Min
Typ
Max
Unit
VOUT = 2 V p-p
VOUT = 0.2 V p-p
VOUT = 0.2 V p-p
VOUT = 2 V p-p, 10% to 90%
0.1%, VOUT = 2 V p-p
VIN = 5 V to 0 V Step
385
285
65
1600
18
5
MHz
MHz
MHz
V/μs
ns
ns
VOUT = 2 V p-p, 5 MHz, RL, dm = 200 Ω
VOUT = 2 V p-p, 20 MHz, RL, dm = 200 Ω
VOUT = 2 V p-p, 5 MHz, RL, dm = 800 Ω
VOUT = 2 V p-p, 20 MHz, RL, dm = 800 Ω
VOUT = 2 V p-p, 5 MHz, RL, dm = 200 Ω
VOUT = 2 V p-p, 20 MHz, RL, dm = 200 Ω
VOUT = 2 V p-p, 5 MHz, RL, dm = 800 Ω
VOUT = 2 V p-p, 20 MHz, RL, dm = 800 Ω
20 MHz, RL, dm = 800 Ω
20 MHz, RL, dm = 800 Ω
f = 20 MHz
NTSC, RL, dm = 150 Ω
NTSC, RL, dm = 150 Ω
−67
−56
−94
−77
−74
−67
−95
−74
−51
29
25
0.02
0.08
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBm
nV/√Hz
%
degrees
Single-ended input
Differential input
1.125
1.5
1
−1.0 to +4.0
−70
kΩ
kΩ
pF
V
dB
ΔVOUT, dm/ΔVIN, cm; ΔVIN, cm = ±0.5 V
VOS, dm = VOUT, dm; VDIN+ = VDIN− = VOCM = 2.5 V
TMIN to TMAX variation
VOCM = float
TMIN to TMAX variation
Maximum ΔVOUT; single-ended output
ΔVOUT, dm/ΔVIN, dm; ΔVIN, dm = ±0.5 V
ΔVOUT, cm/ΔVOUT, dm; ΔVOUT, dm = 1 V
Rev. B | Page 5 of 20
1.96
±3
±8
±4
±10
1.0 to 3.7
45
2
−62
±7
2.04
mV
μV/°C
mV
μV/°C
V
mA
V/V
dB
AD8131
VOCM TO ±OUT SPECIFICATIONS
25°C, VS = 5 V, VOCM = 2.5 V, G = 2, RL, dm = 200 Ω, unless otherwise noted. Refer to Figure 5 and Figure 39 for test setup and label
descriptions. All specifications refer to single-ended input and differential outputs, unless otherwise noted.
Table 4.
Parameter
DYNAMIC PERFORMANCE
−3 dB Bandwidth
Slew Rate
DC PERFORMANCE
Input Voltage Range
Input Resistance
Input Offset Voltage
Input Bias Current
VOCM CMRR
Gain
POWER SUPPLY
Operating Range
Quiescent Current
Power Supply Rejection Ratio
OPERATING TEMPERATURE RANGE
Conditions
Min
ΔVOCM = 600 mV
VOCM = 1.5 V to 3.5 V
VOS, cm = VOUT, cm; VDIN+ = VDIN− = VOCM = 2.5 V
VOCM = float
ΔVOUT, dm/ΔVOCM; ΔVOCM = 2.5 V ±0.5 V
ΔVOUT, cm/ΔVOCM; ΔVOCM = 2.5 V ±1 V
VDIN+ = VDIN− = VOCM = 2.5 V
TMIN to TMAX variation
ΔVOUT, dm/ΔVS; ΔVS = ±0.5 V
0.985
2.7
9.25
−40
Rev. B | Page 6 of 20
Typ
Max
Unit
200
450
MHz
V/μs
1.0 to 3.7
30
±5
±10
0.5
−60
1
V
kΩ
mV
mV
μA
dB
V/V
10.25
20
−70
±12
1.015
11
11.25
−56
+125
V
mA
μA/°C
dB
°C
AD8131
ABSOLUTE MAXIMUM RATINGS
Table 5.1
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only, functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
2.0
Thermal resistance measured on SEMI standard 4-layer board.
8-lead SOIC: θJA = 121°C/W.
8-lead MSOP: θJA = 142°C/W.
TJ = 150°C
MAXIMUM POWER DISSIPATION (W)
1
Rating
±5.5 V
±VS
250 mW
−40°C to +125°C
−65°C to +150°C
300°C
8-LEAD SOIC
PACKAGE
1.5
1.0
8-LEAD
MSOP
PACKAGE
0.5
0
–50
01072-044
Parameter
Supply Voltage
VOCM
Internal Power Dissipation
Operating Temperature Range
Storage Temperature Range
Lead Temperature (Soldering 10 sec)
–20
40
70
10
AMBIENT TEMPERATURE (°C)
100
130
Figure 3. Plot of Maximum Power Dissipation vs. Temperature
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. B | Page 7 of 20
AD8131
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
750Ω
750Ω
VOCM 2
V+ 3
8 +DIN
7 NC
1.5kΩ
1.5kΩ
+OUT 4
6 V–
5 –OUT
AD8131
NC = NO CONNECT
01072-003
–DIN 1
Figure 4. Pin Configuration
Table 6. Pin Function Descriptions
Pin No.
1
2
Mnemonic
−DIN
VOCM
3
4
5
6
7
8
V+
+OUT
−OUT
V−
NC
+DIN
Description
Negative Input.
Common-Mode Output Voltage. Voltage applied to this pin sets the common-mode output voltage with a ratio of
1:1. For example, 1 V dc on VOCM will set the dc bias level on +OUT and −OUT to 1 V.
Positive Supply Voltage.
Positive Output. Note: the voltage at −DIN is inverted at +OUT.
Negative Output. Note: the voltage at +DIN is inverted at −OUT.
Negative Supply Voltage.
No Connect.
Positive Input.
Rev. B | Page 8 of 20
AD8131
TYPICAL PERFORMANCE CHARACTERISTICS
12
VOUT = 2V p-p
VS = ±5V
9
1500Ω
GAIN (dB)
MSOP
750Ω
750Ω
RL, dm = 200Ω
AD8131
24.9Ω
0
01072-004
1500Ω
SOIC
3
–3
01072-007
49.9Ω
6
1
10
100
FREQUENCY (MHz)
Figure 5. Basic Test Circuit
Figure 8. Large Signal Frequency Response
12
12
VOUT = 200mV p-p
VS = ±5V
VOUT = 2V p-p
9
9
VS = ±5V
MSOP
6
GAIN (dB)
GAIN (dB)
1000
3
6
VS = +5V
3
SOIC
01072-005
–3
1
10
100
FREQUENCY (MHz)
01072-008
0
0
–3
1
1000
10
100
FREQUENCY (MHz)
1000
Figure 9. Large Signal Frequency Response
Figure 6. Small Signal Frequency Response
12
VOUT = 200mV p-p
1500Ω
VS = ±5V
6
2:1 TRANSFORMER
750Ω
300Ω
LPF
3
49.9Ω
VS = +5V
–3
750Ω
AD8131
HPF
ZIN = 50Ω
300Ω
1500Ω
1
10
100
FREQUENCY (MHz)
1000
Figure 7. Small Signal Frequency Response
Figure 10. Harmonic Distortion Test Circuit (RL, dm = 800 Ω)
Rev. B | Page 9 of 20
01072-009
24.9Ω
0
01072-006
GAIN (dB)
9
AD8131
–50
–50
RL, dm = 800Ω
VOUT, dm = 1V p-p
VS = 5V
RL, dm = 800Ω
–60
–60
HD3 (F = 20MHz)
DISTORTION (dBc)
–70
HD3 (VS = 5V)
–80
HD2 (V S = 3V)
–90
HD2 (VS = 5V)
–100
HD2 (F = 20MHz)
–80
HD3 (F = 5MHz)
–90
–100
01072-010
–110
–70
0
10
20
30
40
FREQUENCY (MHz)
50
60
–110
70
Figure 11. Harmonic Distortion vs. Frequency
HD2 (F = 5MHz)
01072-013
DISTORTION (dBc)
HD3 (V S = 3V)
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
DIFFERENTIAL OUTPUT VOLTAGE (V p-p)
4.0
Figure 14. Harmonic Distortion vs. Differential Output Voltage
–50
–40
RL, dm = 800Ω
VOUT, dm = 2V p-p
–50
VS = 3V
RL, dm = 800Ω
HD3 (VS = ±5V)
HD3 (F = 5MHz)
–60
HD3 (F = 20MHz)
–70
HD2 (VS = ±5V)
–80
HD2 (VS = +5V)
–90
–80
HD2 (F = 20MHz)
–90
–100
01072-011
–100
–110
–70
0
10
20
30
40
FREQUENCY (MHz)
50
60
HD2 (F = 5MHz)
–110
0.25
70
Figure 12. Harmonic Distortion vs. Frequency
0.50
0.75
1.0
1.25
1.5
DIFFERENTIAL OUTPUT VOLTAGE (V p-p)
–50
VS = ±5V
RL, dm = 800Ω
VS = ±5V
VOUT, dm = 2V p-p
HD3 (F = 20MHz)
–60
–65
DISTORTION (dBc)
HD2 (F = 20MHz)
–75
HD2 (F = 20MHz)
–85
–95
HD3 (F = 20MHz)
–70
–80
–90
HD2 (F = 5MHz)
HD2 (F = 5MHz)
0
HD3 (F = 5MHz)
1
2
3
4
5
DIFFERENTIAL OUTPUT VOLTAGE (V p-p)
01072-015
–100
–105
01072-012
DISTORTION (dBc)
1.75
Figure 15. Harmonic Distortion vs. Differential Output Voltage
–55
–115
01072-014
DISTORTION (dBc)
DISTORTION (dBc)
HD3 (VS = +5V)
–60
HD3 (F = 5MHz)
–110
200
6
300
400
500
600
700
RLOAD (Ω)
800
Figure 16. Harmonic Distortion vs. RLOAD
Figure 13. Harmonic Distortion vs. Differential Output Voltage
Rev. B | Page 10 of 20
900
1000
AD8131
–50
45
VS = 5V
VOUT, dm = 2V p-p
RL, dm = 800Ω
–60
40
HD2 (F = 20MHz)
INTERCEPT (dBm)
–80
HD2 (F = 5MHz)
–100
300
400
500
VS = ±5V
30
25
VS = +5V
20
HD3 (F = 5MHz)
–110
200
35
700
600
RLOAD (Ω)
800
900
15
1000
01072-019
–90
01072-016
DISTORTION (dBc)
HD3 (F = 20MHz)
–70
0
10
20
30
40
50
FREQUENCY (MHz)
60
70
80
Figure 20. Third Order Intercept vs. Frequency
Figure 17. Harmonic Distortion vs. RLOAD
–50
VS = 3V
VOUT, dm = 1V p-p
VS = ±5V
HD3 (F = 20MHz)
–60
VOUT, dm
–70
VOUT+
–80
VOUT–
–90
HD2 (F = 5MHz)
V+DIN
HD3 (F = 5MHz)
01072-017
–100
–110
200
300
400
500
600
700
RLOAD (Ω)
800
900
5ns
1V
1000
Figure 18. Harmonic Distortion vs. RLOAD
01072-020
DISTORTION (dBc)
HD2 (F = 20MHz)
Figure 21. Large Signal Transient Response
10
0
–10
fC = 500MHz
VS = ±5V
RL, dm = 800Ω
VS = +5V
–20
–40
VS = ±5V
–50
–60
–70
–80
–100
–110
49.5
50.0
FREQUENCY (MHz)
50.5
40mV
5ns
Figure 19. Intermodulation Distortion
Figure 22. Small Signal Transient Response
Rev. B | Page 11 of 20
01072-021
–90
01072-018
POUT (dBm)
–30
AD8131
VS = +5V
VOUT = 2V p-p
1500Ω
VS = ±5V
750Ω
49.9Ω
750Ω
24.9Ω
AD8131
CL
24.9Ω
150Ω
01072-025
24.9Ω
01072-022
1500Ω
5ns
400mV
Figure 26. Capacitor Load Drive Test Circuit
Figure 23. Large Signal Transient Response
VOUT = 1.5V p-p
VS = ±5V
CL = 5pF
CL = 0pF
VS = 3V
5ns
400mV
1.25ns
01072-026
300mV
01072-023
CL = 20pF
Figure 27. Large Signal Transient Response for Various Capacitor Loads
Figure 24. Large Signal Transient Response
0
ΔVOUT, dm
VS = ±5V
ΔVS
–10
–20
PSRR (dB)
2mV/DIV
VOUT, dm
–30
–40
+PSRR
(VS = ±5V, +5V)
–50
–PSRR
(VS = ±5V)
4ns
01072-024
–70
V+DIN
–80
Figure 25. 0.1% Settling Time
1
100
10
FREQUENCY (MHz)
Figure 28. PSRR vs. Frequency
Rev. B | Page 12 of 20
01072-027
–60
1V/DIV
1000
AD8131
1500Ω
1500Ω
750Ω
750Ω
750Ω
100Ω
AD8131
VOUT, dm
24.9Ω
VOUT, cm
49.9Ω
100Ω
01072-031
01072-028
24.9Ω
1500Ω
Figure 29. CMRR Test Circuit
Figure 32. Output Balance Error Test Circuit
–20
–20
BALANCE ERROR (dB)
–30
–40
ΔVOUT, dm/ΔVIN, cm
–50
–60
–70
–40
–50
VS = +5V
–60
–70
01072-029
ΔVOUT, cm/ΔVIN, cm
1
ΔVOUT, dm = 2V p-p
ΔVOUT, cm/ΔVOUT, dm
10
100
FREQUENCY (MHz)
–80
1000
VS = ±5V
1
Figure 30. CMRR vs. Frequency
01072-032
VS = ±5V
VIN, cm = 1V p-p
–30
CMRR (dB)
AD8131
100Ω
1500Ω
–80
750Ω
100Ω
10
100
FREQUENCY (MHz)
1000
Figure 33. Output Balance Error vs. Frequency
100
15
SINGLE-ENDED OUTPUT
VS = ±5V
SUPPLY CURRENT (mA)
10
1
VS = +5V
VS = ±5V
11
VS = +5V
9
7
0.1
1
10
FREQUENCY (MHz)
5
–50
100
Figure 31. Single-Ended ZOUT vs. Frequency
01072-034
01072-030
IMPEDANCE (Ω)
13
–20
10
40
70
TEMPERATURE (°C)
100
Figure 34. Quiescent Current vs. Temperature
Rev. B | Page 13 of 20
130
AD8131
–20
110
VS = ±5V
ΔVOUT, cm
VS = ±5V
ΔVOCM
–30
90
ΔVOCM = 600mV p-p
70
CMRR (dB)
NOISE (nV/√Hz)
–40
50
–50
ΔVOCM = 2V p-p
–60
–70
30
1k
10k
100k
1M
FREQUENCY (Hz)
10M
01072-037
01072-035
10
0.1k
–80
–90
100M
1
10
100
FREQUENCY (MHz)
1000
Figure 37. VOCM CMRR vs. Frequency
Figure 35. Voltage Noise vs. Frequency
6
VS = ±5V
ΔVOUT, cm
VS = 5V
VOCM = –1V TO +1V
ΔVOCM
ΔVOCM = 600mV p-p
VOUT, cm
0
–3
ΔVOCM = 2V p-p
–9
1
10
100
FREQUENCY (MHz)
400mV
5ns
1000
Figure 38. VOCM Transient Response
Figure 36. VOCM Gain Response
Rev. B | Page 14 of 20
01072-038
–6
01072-036
GAIN (dB)
3
AD8131
OPERATIONAL DESCRIPTION
RF
RG
+IN
VOCM
–DIN
–OUT
AD8131
RG
–IN
VOUT ,cm = (V+OUT + V−OUT ) 2
–OUT
RL, dm VOUT, dm
+OUT
RF
+OUT
01072-039
+DIN
Common-mode voltage refers to the average of two node
voltages. The output common-mode voltage is defined as
Figure 39. Circuit Definitions
Differential voltage refers to the difference between two node
voltages. For example, the output differential voltage (or
equivalently output differential-mode voltage) shown in
Figure 39 is defined as
VOUT ,dm = (V+OUT − V−OUT )
Balance is a measure of how well differential signals are
matched in amplitude and exactly 180 degrees apart in phase.
Balance is most easily determined by placing a well-matched
resistor divider between the differential voltage nodes and
comparing the magnitude of the signal at the divider’s midpoint
with the magnitude of the differential signal. By this definition,
output balance is the magnitude of the output common-mode
voltage divided by the magnitude of the output differentialmode voltage.
V+OUT and V–OUT refer to the voltages at the +OUT and −OUT
terminals with respect to a common reference.
Rev. B | Page 15 of 20
Output Balance Error =
VOUT , cm
VOUT , dm
AD8131
THEORY OF OPERATION
The AD8131 differs from conventional op amps in that it has
two outputs whose voltages move in opposite directions. Like
an op amp, it relies on high open-loop gain and negative
feedback to force these outputs to the desired voltages. The
AD8131 behaves much like a standard voltage feedback op amp
and makes it easy to perform single-ended-to-differential
conversion, common-mode level-shifting, and amplification of
differential signals.
Previous discrete and integrated differential driver designs used
two independent amplifiers and two independent feedback
loops, one to control each of the outputs. When these circuits
are driven from a single-ended source, the resulting outputs are
typically not well balanced. Achieving a balanced output
typically required exceptional matching of the amplifiers and
feedback networks.
DC common-mode level shifting has also been difficult with
previous differential drivers. Level shifting required the use of a
third amplifier and feedback loop to control the output
common-mode level. Sometimes the third amplifier has also
been used to attempt to correct an inherently unbalanced
circuit. Excellent performance over a wide frequency range has
proven difficult with this approach.
The AD8131 uses two feedback loops to separately control the
differential and common-mode output voltages. The differential
feedback, set by internal resistors, controls only the differential
output voltage. The common-mode feedback controls only the
common-mode output voltage. This architecture makes it easy
to arbitrarily set the common-mode output level. It is forced, by
internal common-mode feedback, to be equal to the voltage
applied to the VOCM input, without affecting the differential
output voltage.
The AD8131 architecture results in outputs that are very highly
balanced over a wide frequency range without requiring
external components or adjustments. The common-mode
feedback loop forces the signal component of the output
common-mode voltage to be zeroed. The result is nearly
perfectly balanced differential outputs, of identical amplitude
and exactly 180 degrees apart in phase.
be assumed to be zero. Starting from these two assumptions,
any application circuit can be analyzed.
CLOSED-LOOP GAIN
The differential mode gain of the circuit in Figure 39 can be
described by the following equation:
VOUT, dm
V IN, dm
RF
=2
RG
where RF = 1.5 kΩ and RG = 750 Ω nominally.
ESTIMATING THE OUTPUT NOISE VOLTAGE
Similar to the case of a conventional op amp, the differential
output errors (noise and offset voltages) can be estimated by
multiplying the input referred terms, at +IN and −IN, by the
circuit noise gain. The noise gain is defined as
⎛R
G N = 1 + ⎜⎜ F
⎝ RG
⎞
⎟=3
⎟
⎠
The total output referred noise for the AD8131, including the
contributions of RF, RG, and op amp, is nominally 25 nV/√Hz
at 20 MHz.
CALCULATING THE INPUT IMPEDANCE OF AN
APPLICATION CIRCUIT
The effective input impedance of a circuit such as that in
Figure 39, at +DIN and −DIN, will depend on whether the
amplifier is being driven by a single-ended or differential signal
source. For balanced differential input signals, the input
impedance (RIN, dm) between the inputs (+DIN and −DIN) is
R IN , dm = 2 × RG = 1.5 kΩ
In the case of a single-ended input signal (for example if −DIN is
grounded and the input signal is applied to +DIN), the input
impedance becomes
R IN , dm
ANALYZING AN APPLICATION CIRCUIT
The AD8131 uses high open-loop gain and negative feedback to
force its differential and common-mode output voltages in such
a way as to minimize the differential and common-mode error
voltages. The differential error voltage is defined as the voltage
between the differential inputs labeled +IN and −IN in
Figure 39. For most purposes, this voltage can be assumed to be
zero. Similarly, the difference between the actual output
common-mode voltage and the voltage applied to VOCM can also
=
⎛
⎞
⎜
⎟
R
⎜
⎟
G
=⎜
⎟ = 1.125 kΩ
RF
⎜⎜ 1 −
⎟
2 × (RG + R F ) ⎟⎠
⎝
The input impedance is effectively higher than it would be for a
conventional op amp connected as an inverter because a
fraction of the differential output voltage appears at the inputs
as a common-mode signal, partially bootstrapping the voltage
across the input resistor RG.
Rev. B | Page 16 of 20
AD8131
INPUT COMMON-MODE VOLTAGE RANGE IN
SINGLE-SUPPLY APPLICATIONS
The AD8131 is optimized for level-shifting ground referenced
input signals. For a single-ended input this would imply, for
example, that the voltage at −DIN in Figure 39 would be zero
volts when the amplifier’s negative power supply voltage (at V−)
was also set to zero volts.
SETTING THE OUTPUT COMMON-MODE VOLTAGE
The AD8131’s VOCM pin is internally biased at a voltage
approximately equal to the midsupply point (average value of
the voltages on V+ and V−). Relying on this internal bias results
in an output common-mode voltage that is within about 25 mV
of the expected value.
In cases where more accurate control of the output commonmode level is required, it is recommended that an external
source, or resistor divider (made up of 10 kΩ resistors), be used.
DRIVING A CAPACITIVE LOAD
A purely capacitive load can react with the pin and bondwire
inductance of the AD8131 resulting in high frequency ringing
in the pulse response. One way to minimize this effect is to
place a small resistor in series with the amplifier’s outputs as
shown in Figure 26.
Rev. B | Page 17 of 20
AD8131
APPLICATIONS
TWISTED-PAIR LINE DRIVER
3 V SUPPLY DIFFERENTIAL A-TO-D DRIVER
The AD8131 has on-chip resistors that provide for a gain of 2
without any external parts. Several on-chip resistors are
trimmed to ensure that the gain is accurate, the common-mode
rejection is good, and the output is well balanced. This makes
the AD8131 very suitable as a single-ended-to-differential
twisted-pair line driver.
Many newer ADCs can run from a single 3 V supply, which can
save significant system power. In order to increase the dynamic
range at the analog input, they have differential inputs, which
double the dynamic range with respect to a single-ended input.
An added benefit of using a differential input is that the
distortion can be improved.
Figure 40 shows a circuit of an AD8131 driving a twisted-pair
line, like a Category 3 or Category 5 (Cat3 or Cat5), that is
already installed in many buildings for telephony and data
communications. The characteristic impedance of such a
transmission line is usually about 100 Ω. The outstanding
balance of the AD8131 output will minimize the commonmode signal and therefore the amount of EMI generated by
driving the twisted pair.
The low distortion and ability to run from a single 3 V supply make
the AD8131 suited as an A-to-D driver for some 10-bit, singlesupply applications. Figure 41 shows a schematic for a circuit for an
AD8131 driving an AD9203, a 10-bit, 40 MSPS ADC.
3V
3V
0.1 F
+
10 F
0.1 F
28
This back-termination of the transmission line divides the
output signal by two. The fixed gain of 2 of the AD8131 will
create a net unity gain for the system from end to end.
3
LPF
8
49.9Ω
2
0.1 F
In this case, the input signal is provided by a signal generator
with an output impedance of 50 Ω. This is terminated with a
49.9 Ω resistor near +DIN of the AD8131. The effective parallel
resistance of the source and termination is 25 Ω.The 24.9 Ω
resistor from −DIN to ground matches the +DIN source
impedance and minimizes any dc and gain errors.
If +DIN is driven by a low-impedance source over a short
distance, such as the output of an op amp, then no termination
resistor is required at +DIN. In this case, the −DIN can be directly
tied to ground.
+5V
0.1μF
+
10μF
10kΩ
10kΩ
24.9Ω
1
3
5
100Ω RECEIVER
AD8131
6
4
49.9Ω
0.1μF
10μF
+
–5V
25
6
110Ω
20pF
AINP
AVSS
27
DIGITAL
OUTPUTS
DRVSS
1
Figure 42 shows an FFT plot that was taken from the combined
devices at an analog input frequency of 2.5 MHz and a 40 MSPS
sampling rate. The performance of the AD8131 compares very
favorably with a center-tapped transformer drive, which has
typically been the best way to drive this ADC. The AD8131 has
the advantage of maintaining dc performance, which a
transformer solution cannot provide.
01072-040
2
49.9Ω
AD9203
VOCM
Figure 41. Test Circuit for AD8131 Driving an AD9203, 10-Bit, 40 MSPS ADC
49.9Ω
8
24.9Ω
2
DRVDD
20pF
AD8131
1
+3V
26 AVDD
AINN
110Ω
01072-041
The two resistors in series with each output terminate the line at
the transmit end. Since the impedances of the outputs of the
AD8131 are very low, they can be thought of as a short-circuit,
and the two terminating resistors form a 100 Ω termination at
the transmit end of the transmission line. The receive end is
directly terminated by a 100 Ω resistor across the line.
The common mode of the AD8131 output is set at midsupply
by the voltage divider connected to VOCM, and ac-bypassed with
a 0.1 μF capacitor. This provides for maximum dynamic range
between the supplies at the output of the AD8131. The 110 Ω
resistors at the AD8131 output, along with the shunt capacitors
form a one pole, low-pass filter for lowering noise and
antialiasing.
Figure 40. Single-Ended-to-Differential 100 Ω Line Driver
Rev. B | Page 18 of 20
AD8131
10
+5V
0
–10
0.1 F
+
10 F
INPUT
–20
–40
8
–50
49.9Ω
–60
2
5
AD8131
1
–70
–OUT
3
6
4
+OUT
–80
–90
0.1 F
–110
–120
2.0
2.1
2.2
2.3
2.4
2.5 2.6
2.7
FREQUENCY (MHz)
2.8
2.9
10 F
+
–5V
01072-042
–100
01072-043
POUT (dBm)
–30
Figure 43. Unity Gain, Single-Ended-to-Differential Amplifier
3.0
Figure 42. FFT Plot for AD8131/AD9203
UNITY-GAIN, SINGLE-ENDED-TO-DIFFERENTIAL
DRIVER
If it is not necessary to offset the output common-mode voltage
(via the VOCM pin), then the AD8131 can make a simple unitygain single-ended-to-differential amplifier that does not require
any external components. Figure 43 shows the schematic for
this circuit.
As shown above, when −DIN is left floating, there is 100%
feedback of +OUT to −IN via the internal feedback resistor.
This contrasts with the typical gain of 2 operation where −DIN is
grounded and one third of the +OUT is fed back to −IN. The
result is a closed-loop differential gain of 1.
Upon careful observation, it can be seen that only +DIN and VOCM
are referenced to ground. The ground voltage at VOCM is the
reference for this circuit. In this unity gain configuration, if a dc
voltage is applied to VOCM to shift the common-mode voltage, a
differential dc voltage will be created at the output, along with the
common-mode voltage change. Thus, this configuration cannot
be used when it is desired to offset the common-mode voltage of
the output with respect to the input at +DIN.
Rev. B | Page 19 of 20
AD8131
OUTLINE DIMENSIONS
5.00 (0.1968)
4.80 (0.1890)
8
5
4.00 (0.1574)
3.80 (0.1497) 1
4
3.00
BSC
6.20 (0.2440)
5.80 (0.2284)
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
8
3.00
BSC
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
COPLANARITY
SEATING 0.31 (0.0122)
0.10
PLANE
0.50 (0.0196)
× 45°
0.25 (0.0099)
1
5
4.90
BSC
4
PIN 1
0.65 BSC
8°
0.25 (0.0098) 0° 1.27 (0.0500)
0.40 (0.0157)
0.17 (0.0067)
1.10 MAX
0.15
0.00
COMPLIANT TO JEDEC STANDARDS MS-012-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
Figure 44. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-8)
Dimensions shown in millimeters and (inches)
0.38
0.22
COPLANARITY
0.10
0.23
0.08
0.80
0.60
0.40
8°
0°
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-187-AA
Figure 45. 8-Lead Mini Small Outline Package [MSOP]
(RM-8)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD8131AR
AD8131AR-REEL
AD8131AR-REEL7
AD8131ARZ 1
AD8131ARZ-REEL1
AD8131ARZ-REEL71
AD8131ARM
AD8131ARM-REEL
AD8131ARM-REEL7
AD8131ARMZ1
AD8131ARMZ-REEL1
AD8131ARMZ-REEL71
1
Temperature Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Package Description
8-Lead Standard Small Outline Package [SOIC_N]
8-Lead SOIC, 13” Tape and Reel
8-Lead SOIC, 7” Tape and Reel
8-Lead Standard Small Outline Package [SOIC_N]
8-Lead SOIC, 13” Tape and Reel
8-Lead SOIC, 7” Tape and Reel
8-Lead Mini Small Outline Package [MSOP]
8-Lead MSOP, 13” Tape and Reel
8-Lead MSOP, 7” Tape and Reel
8-Lead Mini Small Outline Package [MSOP]
8-Lead MSOP, 13” Tape and Reel
8-Lead MSOP, 7” Tape and Reel
Z = Pb-free part, # denotes Pb-free part; may be top or bottom marked.
©2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C01072–0–6/05(B)
Rev. B | Page 20 of 20
Package Option
R-8
R-8
R-8
R-8
R-8
R-8
RM-8
RM-8
RM-8
RM-8
RM-8
RM-8
Branding
HJA
HJA
HJA
HJA#
HJA#
HJA#