AD AD8692ARMZ-R7 Low cost, low noise, cmos, rro operational amplifier Datasheet

Low Cost, Low Noise, CMOS,
RRO Operational Amplifiers
AD8691/AD8692/AD8694
Data Sheet
PIN CONFIGURATIONS
APPLICATIONS
OUT 1
V– 2
V+
4
–IN
TOP VIEW
(Not to Scale)
+IN 3
Figure 1. 5-Lead TSOT
OUT A 1
AD8691
5
V+
4
–IN
V– 2
+IN A 3
Photodiode amplification
Battery-powered instrumentation
Medical instruments
Multipole filters
Sensors
Portable audio devices
5
AD8691
04991-030
Offset voltage: 400 µV typical
Low offset voltage drift: 6 µV/°C maximum (AD8692/AD8694)
Very low input bias currents: 1 pA maximum
Low noise: 8 nV/√Hz
Low distortion: 0.0006%
Wide bandwidth: 10 MHz
Unity-gain stable
Single-supply operation: 2.7 V to 6 V
Qualified for automotive applications
04991-031
FEATURES
Figure 2. 5-Lead SC70
AD8692
8
V+
–IN A 2
7
OUT B
+IN A 3
6
–IN B
V– 4
5
+IN B
GENERAL DESCRIPTION
04991-134
OUT A 1
TOP VIEW
(Not to Scale)
Figure 3. 8-Lead SOIC and 8-Lead MSOP
OUT A
1
14 OUT D
–IN A
2
13 –IN D
+IN A
3
AD8694
V+
4
TOP VIEW
(Not to Scale)
12 +IN D
11 V–
+IN B
5
–IN B
6
9
–IN C
OUT B
7
8
OUT C
10 +IN C
04991-156
The AD8691, AD8692, and AD8694 are low cost, single, dual,
and quad rail-to-rail output, single-supply amplifiers featuring
low offset and input voltages, low current noise, and wide signal
bandwidth. The combination of low offset, low noise, very low
input bias currents, and high speed make these amplifiers useful
in a wide variety of applications. Filters, integrators, photodiode
amplifiers, and high impedance sensors all benefit from this
combination of performance features. Audio and other ac
applications benefit from the wide bandwidth and low
distortion of these devices.
Figure 4. 14-Lead SOIC and 14-Lead TSSOP
Applications for these amplifiers include power amplifier (PA)
controls, laser diode control loops, portable and loop-powered
instrumentation, audio amplification for portable devices, and
ASIC input and output amplifiers.
The small SC70 and TSOT package options for the AD8691
allow it to be placed next to sensors, thereby reducing external
noise pickup.
The AD8691, AD8692, and AD8694 are specified over the
extended industrial temperature range of −40°C to +125°C.
The AD8691 single is available in 5-lead SC70 and 5-lead TSOT
packages. The AD8692 dual is available in 8-lead MSOP and
narrow SOIC surface-mount packages. The AD8694 quad is
available in 14-lead TSSOP and narrow 14-lead SOIC packages.
See the Ordering Guide section for automotive grades.
Rev. F
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2004–2013 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD8691/AD8692/AD8694
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Absolute Maximum Ratings ............................................................5
Applications ....................................................................................... 1
Thermal Characteristics ...............................................................5
General Description ......................................................................... 1
ESD Caution...................................................................................5
Pin Configurations ........................................................................... 1
Typical Performance Characteristics ..............................................6
Revision History ............................................................................... 2
Outline Dimensions ....................................................................... 11
Specifications..................................................................................... 3
Ordering Guide .......................................................................... 14
Electrical Characteristics ............................................................. 3
Automotive Products ................................................................. 14
REVISION HISTORY
9/13—Rev. E to Rev. F
Changes to Figure 3 and Figure 4 ................................................... 1
Delete Figure 4 and Figure 5; Renumbered Sequentially ............ 1
Changes to Ordering Guide .......................................................... 14
8/11—Rev. D to Rev. E
Changes to Figure 20 ........................................................................ 8
11/10—Rev. C to Rev. D
Changes to Features Section and General Descriptions
Section ................................................................................................ 1
Updated Outline Dimensions ....................................................... 11
Changes to Ordering Guide .......................................................... 14
Added Automotive Products Section .......................................... 14
3/05—Rev. A to Rev. B
Added AD8694 ................................................................... Universal
1/05—Rev. 0 to Rev. A
Added AD8691 ................................................................... Universal
Changes to Features ..........................................................................1
Added Figure 1 and Figure 2............................................................1
Changes to Electrical Characteristics .............................................3
Changes to Figure 6 caption.............................................................6
Changes to Figure 9 ...........................................................................6
Updated Outline Dimensions ....................................................... 11
Changes to Ordering Guide .......................................................... 11
10/04—Revision 0: Initial Version
5/07—Rev. B to Rev. C
Change to Figure 1 ........................................................................... 1
Changes to Large Signal Voltage Gain Values in Table 1 ............ 3
Change to Phase Margin Symbol in Table 1 ................................. 3
Change to TA Value for Table 2 ....................................................... 4
Changes to Large Signal Voltage Gain Values in Table 2 ............ 4
Change to Phase Margin Symbol in Table 2 ................................. 4
Changes to Table 4 ............................................................................ 5
Changes to Outline Dimensions................................................... 11
Changes to Ordering Guide .......................................................... 12
Rev. F | Page 2 of 16
Data Sheet
AD8691/AD8692/AD8694
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS
VS = 2.7 V, VCM = VS/2, TA = 25°C, unless otherwise noted.
Table 1.
Parameter
INPUT CHARACTERISTICS
Offset Voltage
Input Bias Current
Symbol
Test Conditions/Comments
VOS
VCM = −0.3 V to +1.6 V
VCM = −0.1 V to +1.6 V; −40°C < TA < +125°C
Min
IB
Typ
Max
Unit
0.4
2.0
3.0
1
50
260
0.5
20
75
+1.6
mV
mV
pA
pA
pA
pA
pA
pA
V
dB
dB
0.2
−40°C < TA < +85°C
−40°C < TA < +125°C
Input Offset Current
IOS
0.1
−40°C < TA < +85°C
−40°C < TA < +125°C
Input Voltage Range
Common-Mode Rejection Ratio
Large Signal Voltage Gain
AD8691/AD8692
AD8694
Offset Voltage Drift
AD8691
AD8692/AD8694
INPUT CAPACITANCE
Common-Mode Input Capacitance
Differential Input Capacitance
OUTPUT CHARACTERISTICS
Output Voltage High
Output Voltage Low
Short-Circuit Current
Closed-Loop Output Impedance
POWER SUPPLY
Power Supply Rejection Ratio
Supply Current/Amplifier
DYNAMIC PERFORMANCE
Slew Rate
Settling Time
Gain Bandwidth Product
Phase Margin
Total Harmonic Distortion + Noise
NOISE PERFORMANCE
Voltage Noise
Voltage Noise Density
Current Noise Density
CMRR
VCM = −0.3 V to +1.6 V
VCM = −0.1 V to +1.6 V; −40°C < TA < +125°C
−0.3
68
60
RL = 2 kΩ, VO = 0.5 V to 2.2 V
RL = 2 kΩ, VO = 0.5 V to 2.2 V
90
60
90
85
AVO
250
V/mV
V/mV
∆VOS/∆T
2
1.3
CCM
CDM
VOH
VOL
ISC
ZOUT
PSRR
ISY
IL = 1 mA
−40°C < TA < +125°C
IL = 1 mA
−40°C < TA < +125°C
2.64
2.6
pF
pF
2.66
V
V
mV
mV
mA
Ω
95
95
0.85
SR
tS
GBP
Øm
THD + N
RL = 2 kΩ
To 0.01%
G = 1, RL = 600 Ω, f = 1 kHz, VO = 250 mV p-p
5
1
10
60
0.003
en p-p
en
en
in
f = 0.1 Hz to 10 Hz
f = 1 kHz
f = 10 kHz
f = 1 kHz
1.6
8
6.5
0.05
Rev. F | Page 3 of 16
40
60
±20
12
80
75
µV/°C
µV/°C
5
2.5
25
f = 1 MHz, AV = 1
VS = 2.7 V to 5.5 V
−40°C < TA < +125°C
VO = 0 V
−40°C < TA < +125°C
12
6
0.95
1.2
dB
dB
mA
mA
V/µs
µs
MHz
Degrees
%
3.0
12
µV p-p
nV/√Hz
nV/√Hz
pA/√Hz
AD8691/AD8692/AD8694
Data Sheet
VS = 5.0 V, VCM = VS/2, TA = 25°C, unless otherwise noted.
Table 2.
Parameter
INPUT CHARACTERISTICS
Offset Voltage
Input Bias Current
Symbol
Test Conditions/Comments
VOS
VCM = −0.3 V to +3.9 V
VCM = −0.1 V to +3.9 V; −40°C < TA < +125°C
Min
IB
Typ
Max
Unit
0.4
2.0
3.0
1
50
260
0.5
20
75
+3.9
mV
mV
pA
pA
pA
pA
pA
pA
V
dB
dB
0.2
−40°C < TA < +85°C
−40°C < TA < +125°C
Input Offset Current
IOS
0.1
−40°C < TA < +85°C
−40°C < TA < +125°C
Input Voltage Range
Common-Mode Rejection Ratio
Large Signal Voltage Gain
AD8691/AD8692
AD8694
Offset Voltage Drift
AD8691
AD8692/AD8694
INPUT CAPACITANCE
Common-Mode Input Capacitance
Differential Input Capacitance
OUTPUT CHARACTERISTICS
Output Voltage High
Output Voltage Low
AD8691/AD8692
AD8694
AD8691/AD8692
AD8694
Short-Circuit Current
Closed-Loop Output Impedance
POWER SUPPLY
Power Supply Rejection Ratio
Supply Current/Amplifier
DYNAMIC PERFORMANCE
Slew Rate
Settling Time
Full Power Bandwidth
Gain Bandwidth Product
Phase Margin
Total Harmonic Distortion + Noise
NOISE PERFORMANCE
Voltage Noise
Voltage Noise Density
Current Noise Density
CMRR
VCM = −0.3 V to +3.9 V
VCM = −0.1 V to +3.9 V; −40°C < TA < +125°C
−0.3
70
67
VO = 0.5 V to 4.5 V, RL = 2 kΩ, VCM = 0 V
VO = 0.5 V to 4.5 V, RL = 2 kΩ, VCM = 0 V
250
150
95
95
AVO
2000
V/mV
V/mV
∆VOS/∆T
2
1.3
CCM
CDM
VOH
VOL
ISC
ZOUT
PSRR
ISY
IL = 1 mA
IL = 10 mA
−40°C to +125°C
IL = 1 mA
IL = 10 mA
IL = 10 mA
−40°C to +125°C
−40°C to +125°C
4.96
4.7
4.6
pF
pF
4.98
4.78
V
V
V
mV
mV
mV
mV
mV
mA
Ω
95
95
0.95
SR
tS
BWP
GBP
Øm
THD + N
RL = 2 kΩ
To 0.01%
<1% distortion
G = 1, RL = 600 Ω, f = 1 kHz, VO = 1 V p-p
5
1
360
10
65
0.0006
en p-p
en
en
in
f = 0.1 Hz to 10 Hz
f = 1 kHz
f = 10 kHz
f = 1 kHz
1.6
8
6.5
0.05
Rev. F | Page 4 of 16
40
210
240
290
370
±80
10
80
75
µV/°C
µV/°C
5
2.5
20
165
185
f = 1 MHz, AV = 1
VS = 2.7 V to 5.5 V
−40°C < TA < +125°C
VO = 0 V
−40°C < TA < +125°C
12
6
1.05
1.3
dB
dB
mA
mA
V/µs
µs
kHz
MHz
Degrees
%
3.0
12
µV p-p
nV/√Hz
nV/√Hz
pA/√Hz
Data Sheet
AD8691/AD8692/AD8694
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
THERMAL CHARACTERISTICS
Table 3.
θJA is specified for the worst-case conditions, that is, the device
soldered in the circuit board for surface-mount packages.
Parameter
Supply Voltage
Input Voltage
Differential Input Voltage
Output Short-Circuit Duration
to GND
Storage Temperature Range
Operating Temperature Range
Junction Temperature Range
Lead Temperature
(Soldering, 60 sec)
Rating
6V
VSS − 0.3 V to VDD + 0.3 V
±6 V
Observe derating curves
Table 4. Thermal Resistance
Package Type
8-Lead MSOP (RM-8)
8-Lead SOIC (R-8)
5-Lead TSOT (UJ-5)
5-Lead SC70 (KS-5)
14-Lead TSSOP (RU-14)
14-Lead SOIC (R-14)
−65°C to +150°C
−40°C to +125°C
−65°C to +150°C
300°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
Rev. F | Page 5 of 16
θJA
210
158
207
376
180
120
θJC
45
43
61
126
35
36
Unit
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
AD8691/AD8692/AD8694
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
VS = +5 V or ±2.5 V, unless otherwise noted.
300
2500
VS = 5V AND 2.7V
VS = 5V
VCM = –0.3V TO +3.9V
250
200
1500
IB (pA)
NUMBER OF AMPLIFIERS
2000
1000
150
100
50
500
0
–1.0
–0.5
0
0.5
1.0
1.5
2.0
VOS (mV)
–50
–40 –30 –20 –10
20
30
40
50
70
60
80
90 100 110 120
Figure 8. Input Bias Current vs. Temperature
1.0
30
VS = 5V AND 2.7V
VCM = 2.5V
TA = –40°C TO +125°C
0.8
SUPPLY CURRENT (mA)
25
20
15
10
0.6
0.4
0
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0
TCVOS (µV/°C)
0
04991-004
0
0
2
3
4
5
6
7
VS (V)
Figure 6. AD8692/AD8694 Input Offset Voltage Drift Distribution
Figure 9. Supply Current vs. Supply Voltage
2.5
2000
1600
1
04991-007
0.2
5
VS = ±2.5V AND ±1.35V
VS = 5V
TA = 25°C
ISY @ ±2.5V
2.0
SUPPLY CURRENT (mA)
1200
800
400
0
–400
–800
ISY @ ±1.35V
1.5
1.0
0.5
–1200
–2000
–0.3 0
0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 3.3 3.6 3.9
COMMON-MODE VOLTAGE (V)
04991-005
–1600
Figure 7. Input Offset Voltage vs. Common-Mode Voltage
0
–40
–20
0
20
40
60
80
100
120
TEMPERATURE (°C)
Figure 10. Supply Current vs. Temperature
Rev. F | Page 6 of 16
140
04991-008
NUMBER OF AMPLIFIERS
10
TEMPERATURE (°C)
Figure 5. Input Offset Voltage Distribution
INPUT OFFSET VOLTAGE (µV)
0
04991-006
–1.5
04991-003
0
–2.0
Data Sheet
AD8691/AD8692/AD8694
100
VS = ±2.5V, ±1.35V
RL = 2kΩ
CL = 15pF
VS = 5V
80
100
AD8691_92 SINK
10
AD8694 SINK
60
40
90
20
45
0
0
AD8691_92 SOURCE
1
0.1
1
10
100
LOAD CURRENT (mA)
–90
–40
1k
1M
10M
Figure 14. Open-Loop Gain and Phase vs. Frequency
35
120
VS = 5V
VS = 5V AND 2.7V
AD8691_92 (V DD – VOH)
30
100
AD8694 (V DD – VOH)
80
CMRR (dB)
20
AD8691_92 (V OL)
15
AD8694 (V OL)
60
40
10
–20
0
20
40
60
80
100
120
TEMPERATURE (°C)
0
04991-010
0
–40
1k
10k
Figure 12. Output Voltage Swing vs. Temperature (IL = 1 mA)
10M
120
VS = 5V
VS = 5V AND 2.7V
AD8691_92 (V DD – VOH)
300
100
AD8694 (V DD – VOH)
PSRR (dB)
80
200
AD8691_92 (V OL)
150
AD8694 (V OL)
100
60
40
20
–20
0
20
40
60
80
100
120
TEMPERATURE (°C)
04991-011
50
0
–40
1M
Figure 15. CMRR vs. Frequency
350
250
100k
FREQUENCY (Hz)
04991-013
20
5
Figure 13. Output Voltage Swing vs. Temperature (IL = 10 mA)
0
10
100
1k
10k
100k
FREQUENCY (Hz)
Figure 16. PSRR vs. Frequency
Rev. F | Page 7 of 16
1M
10M
04991-014
OUTPUT VOLTAGE SWING (mV)
100k
FREQUENCY (Hz)
Figure 11. Output Voltage to Supply Rail vs. Load Current
25
10k
04991-012
0.01
–45
–20
AD8694 SOURCE
0.1
0.001
OUTPUT VOLTAGE SWING (mV)
PHASE (Degrees)
OPEN-LOOP GAIN (dB)
1000
04991-009
OUTPUT VOLTAGE TO SUPPLY RAIL (mV)
10000
AD8691/AD8692/AD8694
Data Sheet
10000
VS = 5V
CL = 200pF
RL = ∞
AV = 1
VS = ±2.5V
1000
IMPEDANCE (Ω)
10
VOLTAGE (1V/DIV)
AV = 100
100
AV = 10
1
AV = 1
0.1
0.01
1k
10k
100k
1M
10M
FREQUENCY (Hz)
04991-018
0.0001
100
04991-015
0.001
TIME (400ns/DIV)
Figure 20. Large Signal Transient Response
Figure 17. Closed-Loop Output Impedance vs. Frequency
40
VS = 5V AND 2.7V
RL = ∞
AV = –1
35
VS = ±2.5V
AV = –50
VOUT (V)
25
20
0
–2.5
100
15
VIN (mV)
10
1
10
100
1k
LOAD CAPACITANCE (pF)
04991-016
0
04991-019
0
5
TIME (400ns/DIV)
Figure 18. Small Signal Overshoot vs. Load Capacitance
Figure 21. Positive Overload Recovery
VS = ±2.5V, ±1.35V
RL = 10kΩ
CL = 200pF
AV = 1
VOLTAGE (50mV/DIV)
VOUT (V)
VS = ±2.5V
AV = –50
2.5
0
VIN (mV)
0
TIME (200ns/DIV)
04991-017
–100
TIME (400ns/DIV)
Figure 22. Negative Overload Recovery
Figure 19. Small Signal Transient Response
Rev. F | Page 8 of 16
04991-020
OVERSHOOT (%)
30
Data Sheet
AD8691/AD8692/AD8694
1000
0.1
VS = ±2.5V AND ±1.35V
VS = ±2.5V
AV = 1
VIN = 1V p-p
BW = 20kHz
NOISE (nV/ Hz)
THD + N (%)
0.01
RL = 600Ω
RL = 1kΩ
0.001
100
10
1k
10k
FREQUENCY (Hz)
20k
1
04991-021
100
1
10
100
10000
1000
FREQUENCY (Hz)
Figure 23. THD + N vs. Frequency
04991-023
RL = 100kΩ
0.0001
20
Figure 25. Voltage Noise Density
150
+2.5V
VS = 5V AND 2.7V
CHANNEL SEPARATION (dB)
140
VOLTAGE NOISE (1µV/DIV)
R1
10kΩ
V+
A
VIN
28mV p-p
V–
V–
130
–2.5V
VOUT
R2
100Ω
B
V+
120
110
100
Figure 24. 0.1 Hz to 10 Hz Input Voltage Noise
80
1k
10k
100k
1M
10M
FREQUENCY (Hz)
Figure 26. AD8692/AD8694 Channel Separation
Rev. F | Page 9 of 16
04991-024
TIME (1s/DIV)
04991-022
90
AD8691/AD8692/AD8694
Data Sheet
VS = +2.7 V or ±1.35 V, unless otherwise noted.
60
1200
VS = 2.7V
VCM = –0.3V TO +1.6V
VS = 2.7V
AD8691_92 (V DD – VOH)
800
600
400
0
–2.0
–1.5
–1.0
0
–0.5
0.5
1.0
2.0
1.5
VOS (mV)
AD8694 (V DD – VOH)
40
30
AD8691_92 (V OL)
20
AD8694 (V OL)
10
0
–40
04991-025
200
50
–20
0
20
40
60
2000
120
VS = 2.7V
CL = 200pF
RL = ∞
AV = 1
VS = 2.7V
TA = 25°C
1200
VOLTAGE (500mV/DIV)
INPUT OFFSET VOLTAGE (µV)
100
Figure 30. Output Voltage Swing vs. Temperature (IL = 1 mA)
Figure 27. Input Offset Voltage Distribution
1600
80
TEMPERATURE (°C)
04991-028
OUTPUT VOLTAGE SWING (mV)
NUMBER OF AMPLIFIERS
1000
800
400
0
–400
–800
–1200
0
0.3
0.6
0.9
1.2
1.5 1.6
COMMON-MODE VOLTAGE (V)
Figure 31. Large Signal Transient Response
Figure 28. Input Offset Voltage vs. Common-Mode Voltage
VS = 2.7V
1k
100
AD8691_92 SINK
AD8694 SINK
AD8691_92 SOURCE
1
AD8694 SOURCE
0.1
0.001
0.01
0.1
1
10
LOAD CURRENT (mA)
04991-027
OUTPUT VOLTAGE TO SUPPLY RAIL (mV)
10k
10
TIME (400ns/DIV)
Figure 29. Output Voltage to Supply Rail vs. Load Current
Rev. F | Page 10 of 16
04991-029
–2000
–0.3
04991-026
–1600
Data Sheet
AD8691/AD8692/AD8694
OUTLINE DIMENSIONS
3.20
3.00
2.80
5.15
4.90
4.65
5
8
3.20
3.00
2.80
1
4
PIN 1
IDENTIFIER
0.65 BSC
0.95
0.85
0.75
15° MAX
1.10 MAX
0.80
0.55
0.40
0.23
0.09
6°
0°
0.40
0.25
10-07-2009-B
0.15
0.05
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-187-AA
Figure 32. 8-Lead Mini Small Outline Package [MSOP]
(RM-8)
Dimensions shown in millimeters
5.00 (0.1968)
4.80 (0.1890)
1
5
6.20 (0.2441)
5.80 (0.2284)
4
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
COPLANARITY
0.10
SEATING
PLANE
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
0.31 (0.0122)
0.50 (0.0196)
0.25 (0.0099)
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-012-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 33. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body (R-8)
Dimensions shown in millimeters and (inches)
Rev. F | Page 11 of 16
012407-A
8
4.00 (0.1574)
3.80 (0.1497)
AD8691/AD8692/AD8694
Data Sheet
2.20
2.00
1.80
1.35
1.25
1.15
5
1
2.40
2.10
1.80
4
3
2
0.65 BSC
0.40
0.10
1.10
0.80
0.10 MAX
COPLANARITY
0.10
0.46
0.36
0.26
0.22
0.08
SEATING
PLANE
0.30
0.15
072809-A
1.00
0.90
0.70
COMPLIANT TO JEDEC STANDARDS MO-203-AA
Figure 34. 5-Lead Thin Shrink Small Outline Package [SC70]
(KS-5)
Dimensions shown in millimeters
2.90 BSC
4
5
2.80 BSC
1.60 BSC
1
2
3
0.95 BSC
1.90
BSC
*1.00 MAX
0.10 MAX
0.50
0.30
0.20
0.08
SEATING
PLANE
8°
4°
0°
0.60
0.45
0.30
*COMPLIANT TO JEDEC STANDARDS MO-193-AB WITH
THE EXCEPTION OF PACKAGE HEIGHT AND THICKNESS.
Figure 35. 5-Lead Thin Small Outline Transistor Package [TSOT]
(UJ-5)
Dimensions shown in millimeters
Rev. F | Page 12 of 16
100708-A
*0.90 MAX
0.70 MIN
Data Sheet
AD8691/AD8692/AD8694
5.10
5.00
4.90
14
8
4.50
4.40
4.30
6.40
BSC
1
7
PIN 1
0.65 BSC
1.20
MAX
0.15
0.05
COPLANARITY
0.10
0.20
0.09
0.30
0.19
0.75
0.60
0.45
8°
0°
SEATING
PLANE
061908-A
1.05
1.00
0.80
COMPLIANT TO JEDEC STANDARDS MO-153-AB-1
Figure 36. 14-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-14)
Dimensions shown in millimeters
8.75 (0.3445)
8.55 (0.3366)
8
14
1
7
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0039)
COPLANARITY
0.10
0.51 (0.0201)
0.31 (0.0122)
6.20 (0.2441)
5.80 (0.2283)
0.50 (0.0197)
0.25 (0.0098)
1.75 (0.0689)
1.35 (0.0531)
SEATING
PLANE
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-012-AB
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 37. 14-Lead Standard Small Outline Package [SOIC_N]
Narrow Body (R-14)
Dimensions shown in millimeters and (inches)
Rev. F | Page 13 of 16
060606-A
4.00 (0.1575)
3.80 (0.1496)
AD8691/AD8692/AD8694
Data Sheet
ORDERING GUIDE
Model 1, 2
AD8691AUJZ-R2
AD8691AUJZ-REEL
AD8691AUJZ-REEL7
AD8691AKSZ-R2
AD8691AKSZ-REEL
AD8691AKSZ-REEL7
AD8691WAUJZ-R7
AD8691WAUJZ-RL
AD8692ARMZ-R7
AD8692ARMZ-REEL
AD8692ARZ
AD8692ARZ-REEL
AD8692ARZ-REEL7
AD8692WARMZ-REEL
AD8694ARUZ
AD8694ARUZ-REEL
AD8694WARUZ
AD8694WARUZ-REEL
AD8694ARZ
AD8694ARZ-REEL
AD8694ARZ-REEL7
AD8694WAC-P3
AD8694WAC-P7
1
2
Temperature Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Package Description
5-Lead TSOT
5-Lead TSOT
5-Lead TSOT
5-Lead SC70
5-Lead SC70
5-Lead SC70
5-Lead TSOT
5-Lead TSOT
8-Lead MSOP
8-Lead MSOP
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead MSOP
14-Lead TSSOP
14-Lead TSSOP
14-Lead TSSOP
14-Lead TSSOP
14-Lead SOIC_N
14-Lead SOIC_N
14-Lead SOIC_N
Die
Die
Package Option
UJ-5
UJ-5
UJ-5
KS-5
KS-5
KS-5
UJ-5
UJ-5
RM-8
RM-8
R-8
R-8
R-8
RM-8
RU-14
RU-14
RU-14
RU-14
R-14
R-14
R-14
Branding
ACA
ACA
ACA
ACA
ACA
ACA
ACA
ACA
APA
APA
APA
Z = RoHS Compliant Part.
W = Qualified for Automotive Applications.
AUTOMOTIVE PRODUCTS
The AD8691W/AD8692W/AD8694W models are available with controlled manufacturing to support the quality and reliability
requirements of automotive applications. Note that these automotive models may have specifications that differ from the commercial
models; therefore, designers should review the Specifications section of this data sheet carefully. Only the automotive grade products
shown are available for use in automotive applications. Contact your local Analog Devices account representative for specific product
ordering information and to obtain the specific Automotive Reliability reports for these models.
Rev. F | Page 14 of 16
Data Sheet
AD8691/AD8692/AD8694
NOTES
Rev. F | Page 15 of 16
AD8691/AD8692/AD8694
NOTES
©2004–2013 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D04991-0-9/13(F)
Rev. F | Page 16 of 16
Similar pages