RS GS1A THRU GS1M SURFACE MOUNT STANDARD RECOVERY RECTIFIER VOLTAGE - 50 TO 1000 VOLTS CURRENT - 1.0 AMPERE FEATURES SMA / DO-214AC Dim Min Max A 2.29 2.92 B 4.00 4.60 1.25 1.65 C 0.152 0.305 D 4.80 5.59 E 0.051 0.203 G 0.76 1.52 H 2.00 2.62 J All Dimensions in mm B C A D J H For surface mount applications Glass passivated junction Low profile package Built-in strain relief Easy pick and place Low forward voltage drop Plastic package has Underwriters Laboratory Flammability Classification 94V-0 High temperature soldering: 250oC/10 seconds at terminals G E MECHANICAL DATA Case: JEDEC DO-214AC molded plastic Terminals: Solder plated, solderable per MIL-STD-202, method 208 Polarity: Color band denotes cathode end Standard Package: 12mm tape (EIA STD EIA-481) Weight: 0.002 ounce, 0.064 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25oC ambient temperature unless otherwise specified Single phase half wave 60 Hz, resistive or inductive load For capacitive load, derate current by 20% Maximum Repetitive Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at TL = 100oC SYMBOL GS1A GS1B GS1D GS1G GS1J GS1K GS1M UNITS 50 100 200 400 600 VRRM 800 1000 Volts 35 70 140 280 420 VRMS 560 700 Volts 50 100 200 400 600 800 1000 Volts VDC I(AV) 1.0 Amps IFSM 30 Amps VF 1.1 Volts IR 5 50 A CJ 12 pF Peak Forward Surge Current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum Instantaneous Forward Voltage at 1.0A Maximum DC Reverse Current TA = 25oC at Rated DC Blocking Voltage TA = 125oC Typical Junction Capacitance (NOTE 1) Maximum Thermal Resistance (NOTE 2) Operating and Storage Temperature Range R R JA JL TJ, TSTG NOTES: 1. Measured at 1.0 MHz and applied reverse voltage of 4.0 volts 2. P.C.B. mounted on 0.2 x 0.2" (5.0 x 5.0mm) copper pad areas 75 30 -55 to +150 o C/W o C RS GS1A THRU GS1M P.C.B. MOUNTED ON 0.2 x 0.2" (5.0 x 5.0mm) COPPER PAD AREAS 1.0 SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 0.5 0 0 25 50 75 100 125 150 175 PEAK FORWARD SURGE CURRENT (AMPS) AVERAGE FORWARD CURRENT (AMPS) 30 1.5 O LEAD TEMPERATURE ( C) Figure 1. Typical Forward Current Derating Curve 25 8.3 MS SINGLE HALF SINE-WAVE JEDEC METHOD 20 15 10 5 0 100 10 1 NUMBER OF CYCLES AT 60Hz 100 100 10 1 TJ = 25OC PULSE WIDTH = 300 1% DUTY CYCLE TJ = 25OC f = 1.0MHz Vsig = 50mVp-p JUNCTION CAPACITANCE (pF) INSTANTANEOUS FORWARD CURRENT (AMPS) Figure 2. Maximum Non-Repetitive Peak Forward Surge Current S 0.1 10 1 0.01 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0.1 2.0 1.0 10 100 REVERSE VOLTAGE (VOLTS) Figure 4.Typical Junction Capacitance INSTANTANEOUS FORWARD VOLTAGE (VOLTS) Figure 3. Typical Instantaneous Forward Characteristics INSTANTANEOUS REVERSE CURRENT A) 10 THERMAL IMPEDANCE (OC / W) 1000 100 10 UNITS MOUNTED ON 0.2x0.2" (5.0x5.0mm) x 0.5mil. INCHES (0.013mm) THICK COPPER LAND AREAS TJ = 125 OC 1 TJ = 100 OC 0.1 TJ = 25 OC 0.01 1 0.01 0.1 1.0 10 HEATING TIME (SEC) Figure 5.Transient Thermal Impedance 100 0.001 0 20 40 60 80 PERCENT OF PEAK REVERSE VOLT AGE(%) Figure 6.Typical Reverse Characteristics 100