Pan Jit GBU10A Glass passivated single-phase bridge rectifier Datasheet

DATA SHEET
GBU10A~GBU10K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
CURRENT 10 Amperes
VOLTAGE 50 to 800 Volts
GBU
Unit: inch (mm)
Recongnized File #E228882
FEATURES
.880(22.3)
.860(21.8)
.310(7.90)
.290(7.40)
• Reliable low cost construction utilizing molded plastic technique
.160(4.1)
.140(3.5)
.080(2.03)
.060(1.52)
• Surge overload rating: 200 Amperes peak
.075(1.90)R
260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
• Pb free product are available : 99% Sn above can meet Rohs environment substance
directive request
.085(2.16)
.065(1.65)
• High temperature soldering guaranteed:
.140(3.56)
.130(3.30)
.740(18.8)
.720(18.3)
• Ideal for printed circuit board
.710(18.0)
.690(17.5)
• Plastic material has Underwriters Laboratory Flammability Classification 94V-O
.040(1.02)
.030(0.76)
.030(0.75)
.017(0.45)
.100(2.54)
.085(2.16)
MECHANICALDATA
Case: Reliable low cost construction utilizing
.080(2.03)
.065(1.65)
molded plastic technique
Terminals: Leads solderable per MIL-STD-202, Method 208
.190(4.83)
.210(5.33)
Mounting position: Any
.050(1.27)
.040(1.02)
Mounting torque: 5 in. lb. Max.
Weight: 0.15 ounce, 4.0 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz. For Capacitive load derate current by 20%.
P A R A M E TE R
S YM B O L
G B U 10A
G B U 10B G B U 10D G B U 10G G B U 10J G B U 10K
U N IT S
M a xim um R e curre nt P e a k R e ve rse V o lta g e
V RRM
50
100
200
400
600
800
V
M a xim um R M S B rid g e Inp ut V o lta g e
V RM S
35
70
140
280
420
560
V
M a xim um D C B lo cking V o lta g e
VDC
50
100
200
400
600
800
V
M a xim um A ve ra g e F o rw a rd T C = 1 0 0 O C
R e ctifie d O utp ut C urre nt a t T A = 4 5 O C
IA V
1 0 .0
A
I2 t R a ting fo r fusing ( t< 8 .3 m s)
I2 t
166
A 2 se c
IF S M
200
A pk
M a xim um Insta nta ne o us F o rw a rd V o lta g e D ro p p e r
e le m e nt a t 5 .0 A
VF
1 .0
V pk
M a xim um R e ve rse L e a ka g e C urre nt a t R a te d @ T A = 2 5 O C
D c B lo cking V o lta g e @ T A = 1 0 0 O C
IR
5 .0
500
uA
R θ JA
R θ JC
8 .6
3 .1
T J,T S TG
-5 5 to + 1 5 0
P e a k F o rw a rd S urg e C urre nt sing le sine -w a ve sup e rim p o se d
o n ra te d lo a d (JE D E C m e tho d )
Typ ica l T he rm a l R e sista nce p e r le g (N o te 2 )
(N o te 3 )
O p e ra ting Junctio n a nd S to ra g e Te m p e ra ture R a ng e
O
C /W
O
C
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.
STAD-AUG.19.2004
PAGE . 1
10
HEAT-SINK
MOUNTING, TC
(4X4X0.15) INCH
COPPER PLATE
8
6
4
60Hz RESISTIVE OR
INDUCTIVE LOAD
MOUNTED ON 0.5X0.5 INCH
COPPER PC BOARD, TA
0.5"(12.7mm) LEAD LENGTH
2
0
0
50
100
150
FORWARD SURGE CURRENT, AMPERES pk
(HALF SINE-WAVE)
AVERAGE FORWARD CURRENT
AMPERES
RATING AND CHARACTERISTIC CURVES
200
160
120
80
40
0
1
10
3
10
2
10
10
T J =150 OC
1
0
O
T J =25 C
10
10
-1
-2
0
10
20
30
40
50
60
70
80
90
100 110
PERCENT OF PEAK REVERE VOLTAGE,%
Fig.3 - TYPICAL REVERSE CHARACTERISTICS
STAD-AUG.19.2004
20
40
60
100
Fig.2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
INSTANTANEOUS FORWARD CURRENT, AMPERES
REVERSE CURRENT,uA
Fig.1 - DERATING CURVE FOR OUTPUT
RECTIFIED CURRENT
4
10
NO. OF CYCLES AT 60Hz
O
TEMPERATURE, C
10
6
2
100
40
20
10
4.0
2.0
1.0
O
TJ=25 C
Pulse Width = 300us
1% DULY Cycle
0.4
0.2
0.1
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
INSTANTANEOUS FORWARD VOLTAGE, VOLTS
Fig.4 - TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS PER ELEMENT
PAGE . 2
Similar pages