Kemet C1825X393BFGACAUTO High voltage with flexible termination system (hv ft-cap), c0g dielectric, 500 - 3,000 vdc (automotive grade) Datasheet

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP),
C0G Dielectric, 500 – 3,000 VDC (Automotive Grade)
Overview
KEMET’s Automotive Grade High Voltage with Flexible Termination
(HV FT-CAP) surface mount MLCCs in C0G dielectric address the
primary failure mode of MLCCs– flex cracks, which are typically
the result of excessive tensile and shear stresses produced during
board flexure and thermal cycling. Featuring several of the highest
CV (capacitance/voltage) values available in the industry, these
devices utilize a pliable and conductive silver epoxy between the
base metal and nickel barrier layers of the termination system. The
addition of this epoxy layer inhibits the transfer of board stress to
the rigid ceramic body, therefore mitigating flex cracks which can
result in low IR or short circuit failures. Although flexible termination
technology does not eliminate the potential for mechanical damage
that may propagate during extreme environmental and handling
conditions, it does provide superior flex performance over standard
termination systems.
switching power supplies and lighting ballasts. Their exceptional
performance at high frequencies has made high voltage MLCC’s the
preferred dielectric choice of design engineers worldwide. In addition
to their use in power supplies, these capacitors are widely used in
industries related to automotive (hybrid), telecommunications, medical,
military, aerospace, semiconductors and test/diagnostic equipment.
Whether under-hood or in-cabin, these capacitors are designed to
provide reliable performance in mission and safety critical automotive
circuits. Stricter testing protocol and inspection criteria have been
established for automotive grade products in recognition of potentially
harsh environmental conditions. KEMET automotive grade series
capacitors meet the demanding Automotive Electronics Council’s
AEC-Q200 qualification requirements.
KEMET’s high voltage surface mount MLCCs in C0G dielectric
feature a 125°C maximum operating temperature and offers the most
stable voltage and temperature performance of all ceramic dielectric
materials. C0G (NP0) dielectric capacitors exhibit no change in
capacitance with respect to time and voltage and boasts a negligible
change in capacitance with reference to ambient temperature.
Capacitance change is limited to ±30ppm/ºC from −55°C to +125°C.
These devices exhibit low ESR at high frequencies and find
conventional use as snubbers or filters in applications such as
Click image above for interactive 3D content
Open PDF in Adobe Reader for full functionality
Ordering Information
C
2225
X
Case Size Specification/
Ceramic
(L" x W")
Series
0805
1206
1210
1808
1812
1825
2220
2225
1
2
X= Flexible
Termination
393
J
Capacitance
Code (pF)
Capacitance
Tolerance1
Two significant
digits +
number of zeros.
B = ±0.10 pF
C = ±0.25 pF
D = ±0.5 pF
F = ±1%
G = ±2%
J = ±5%
K = ±10%
M = ±20%
C
AUTO
Rated Voltage
Failure Rate/
Dielectric
(VDC)
Design
C
G
Termination
Finish2
Packaging/Grade (C-Spec)
C = 500
B = 630
D = 1,000
F = 1,500
G = 2,000
Z = 2,500
H = 3,000
C = 100%
Matte Sn
G = C0G
A
A = N/A
See
“Packaging C-Spec
Ordering Options Table”
below
Additional capacitance tolerance offerings may be available. Contact KEMET for details.
Additional termination finish options may be available. Contact KEMET for details.
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1081_C0G_HV_FT_AUTO_SMD • 2/29/2016 1
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP), C0G Dielectric, 500 – 3,000 VDC (Automotive Grade)
Packaging C-Spec Ordering Options Table
Packaging/Grade
Ordering Code (C-Spec)3
Packaging Type1
7" Reel
13" Reel / Unmarked
7" Reel/Unmarked/2 mm pitch2
13" Reel/Unmarked/2 mm pitch2
AUTO
AUTO7411 (EIA 0603 and smaller case sizes)
AUTO7210 (EIA 0805 and larger case sizes)
3190
3191
Reeling tape options (Paper or Plastic) are dependent on capacitor case size (L” x W”) and thickness dimension. See “Chip Thickness/Tape & Reel Packaging
Quantities” and “Tape & Reel Packaging Information”.
2
The 2 mm pitch option allows for double the packaging quantity of capacitors on a given reel size. This option is limited to EIA 0603 (1608 metric) case size
devices. For more information regarding 2 mm pitch option see “Tape & Reel Packaging Information”.
3
All Automotive packaging C-Specs listed exclude the option to laser mark components. Please contact KEMET if you require a laser marked option. For more
information see “Capacitor Marking”.
3
For additional Information regarding “AUTO” C-Spec options, see “Automotive C-Spec Information”.
1
Benefits
•
•
•
•
•
•
•
•
•
AEC-Q200 automotive qualified
−55°C to +125°C operating temperature range
Superior flex performance (up to 5 mm)
Lead (Pb)-Free, RoHS, and REACH compliant
EIA 0805, 1206, 1210, 1808, 1812, 1825, 2220 and 2225
case sizes
DC voltage ratings of 500 V, 630 V, 1 KV, 1.5 KV, 2 KV,
2.5 KV and 3 KV
Capacitance offerings ranging from 1 pF to 39 nF
Available capacitance tolerances of ±0.10 pF, ±0.25 pF,
±0.5 pF, ±1%, ±2%, ±5%, ±10% and ±20%
No piezoelectric noise
•
•
•
•
•
•
•
•
•
Extremely low ESR & ESL
High thermal stability
High ripple current capability
Preferred capacitance solution at line frequencies & into the
MHz range
No capacitance change with respect to applied rated DC voltage
Negligible capacitance change with respect to temperature from
−55°C to +125°C
No capacitance decay with time
Non-polar device, minimizing installation concerns
100% pure matte tin-plated termination finish allowing for
excellent solderability
Applications
Typical applications include switch mode power supplies (input filters, resonators, tank circuits, snubbed circuits, output filters), high
voltage coupling and DC blocking, lighting ballasts, voltage multiplier circuits, DC/DC converters and coupling capacitors in Ćuk
converters. Markets include power supply, LCD fluorescent backlight ballasts, HID lighting, telecom equipment, industrial and medical
equipment/control, LAN/WAN interface, analog and digital modems, and automotive.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1081_C0G_HV_FT_AUTO_SMD • 2/29/2016 2
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP), C0G Dielectric, 500 – 3,000 VDC (Automotive Grade)
Automotive C-Spec Information
KEMET Automotive Grade products meet or exceed the requirements outlined by the Automotive Electronics Council. Details regarding
test methods and conditions are referenced in document AEC–Q200, Stress Test Qualification for Passive Components. These
products are supported by a Product Change Notification (PCN) and Production Part Approval Process warrant (PPAP).
Automotive products offered through our distribution channel have been assigned an inclusive ordering code C-Spec, "AUTO". This
C-Spec was developed in order to better serve small and medium sized companies that prefer an automotive grade component without
the requirement to submit a customer Source Controlled Drawing (SCD) or specification for review by a KEMET engineering specialist.
This C-Spec is therefore not intended for use by KEMET’s OEM Automotive customers and are not granted the same “privileges” as
other automotive C-Specs. Customer PCN approval and PPAP request levels are limited (see details below).
Product Change Notification (PCN)
The KEMET Product Change Notification system is used to communicate primarily the following types of changes:
• Product/process changes that affect product form, fit , function, and /or reliability
• Changes in manufacturing site
• Product obsolescence
Customer Notification due to:
KEMET Automotive
C-Spec
1
Process/Product change
Obsolescence*
Days prior to
implementation
KEMET assigned1
Yes (with approval and
sign off)
Yes
180 days Minimum
AUTO
Yes (without approval)
Yes
90 days Minimum
KEMET assigned C-Specs require the submittal of a customer SCD or customer specification for review. For additional information contact KEMET.
Production Part Approval Process (PPAP)
The purpose of the Production Part Approval Process is:
• To ensure that supplier can meet the manufacturability and quality requirements for the purchased parts.
• To provide the evidence that all customer engineering design record and specification requirements are properly understood and
fulfilled by the manufacturing organization.
• To demonstrate that the established manufacturing process has the potential to produce the part
KEMET
Automotive
C-Spec
1
PPAP (Product Part Approval Process) Level
1
2
3
4
5
KEMET
assigned1
●
●
●
●
●
AUTO
○
○
KEMET assigned C-Specs require the submittal of a customer SCD or customer specification for review. For additional information contact KEMET.
● Part Number specific PPAP available
○ Product family PPAP only
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1081_C0G_HV_FT_AUTO_SMD • 2/29/2016 3
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP), C0G Dielectric, 500 – 3,000 VDC (Automotive Grade)
Dimensions – Millimeters (Inches)
L
W
B
T
S
EIA
Size
Code
Metric
Size
Code
B
Bandwidth
S
Separation
Minimum
0805
2012
2.00 (.079) ± 0.30 (.012) 1.25 (.049) ± 0.30 (.012)
0.50 (0.02) ± 0.25 (.010)
0.75 (.030)
1206
3216
3.30 (.130) ± 0.40 (.016) 1.60 (.063) ± 0.35 (.013)
0.60 (.024) ± 0.25 (.010)
1210
3225
3.30 (.130) ± 0.40 (.016) 2.60 (.102) ± 0.30 (.012)
0.60 (.024) ± 0.25 (.010)
1808
4520
1812
4532
4.70 (.185) ± 0.50 (.020) 2.00 (.079) ± 0.20 (.008) See Table 2 for 0.70 (.028) ± 0.35 (.014)
Thickness
4.50 (.178) ± 0.40 (.016) 3.20 (.126) ± 0.30 (.012)
0.70 (.028) ± 0.35 (.014)
1825
4564
4.60 (.181) ± 0.40 (.016) 6.40 (.252) ± 0.40 (.016)
0.70 (.028) ± 0.35 (.014)
2220
5650
5.90 (.232) ± 0.75 (.030) 5.00 (.197) ± 0.40 (.016)
0.70 (.028) ± 0.35 (.014)
2225
5664
5.90 (.232) ± 0.75 (.030) 6.40 (.248) ± 0.40 (.016)
0.70 (.028) ± 0.35 (.014)
L
Length
W
Width
T
Thickness
N/A
Mounting
Technique
Solder Wave or
Solder Reflow
Solder Reflow Only
Qualification/Certification
Automotive Grade products meet or exceed the requirements outlined by the Automotive Electronics Council. Details regarding test
methods and conditions are referenced in document AEC–Q200, Stress Test Qualification for Passive Components. For additional
information regarding the Automotive Electronics Council and AEC–Q200, please visit their website at www.aecouncil.com.
Environmental Compliance
Lead (Pb)-Free, RoHS, and REACH compliant without exemptions.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1081_C0G_HV_FT_AUTO_SMD • 2/29/2016 4
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP), C0G Dielectric, 500 – 3,000 VDC (Automotive Grade)
Electrical Parameters/Characteristics
Item
Parameters/Characteristics
Operating Temperature Range
Capacitance Change with Reference to +25°C and 0 VDC Applied (TCC)
Aging Rate (Maximum % Capacitance Loss/Decade Hour)
Dielectric Withstanding Voltage (DWV)
1
2
Dissipation Factor (DF) Maximum Limit at 25ºC
3
Insulation Resistance (IR) Limit at 25°C
−55°C to +125°C
±30 ppm/ºC
0%
150% of rated voltage for voltage rating of < 1,000 V
120% of rated voltage for voltage rating of ≥ 1,000 V
(5 ±1 seconds and charge/discharge not exceeding 50 mA)
0.1%
1,000 megohm microfarads or 100 GΩ
(500 VDC applied for 120 ±5 seconds at 25°C)
DWV is the voltage a capacitor can withstand (survive) for a short period of time. It exceeds the nominal and continuous working voltage of the capacitor.
Capacitance and dissipation factor (DF) measured under the following conditions:
1 MHz ±100 kHz and 1.0 Vrms ±0.2 V if capacitance ≤ 1,000 pF
1 kHz ±50 Hz and 1.0 Vrms ±0.2 V if capacitance > 1,000 pF
3
To obtain IR limit, divide MΩ-µF value by the capacitance and compare to GΩ limit. Select the lower of the two limits.
Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 and Agilent E4980 have a feature known as
Automatic Level Control (ALC). The ALC feature should be switched to “ON.”
1
2
Post Environmental Limits
High Temperature Life, Biased Humidity, Moisture Resistance
Dielectric
Rated DC
Voltage
Capacitance
Value
Dissipation Factor
(Maximum %)
C0G
All
All
0.5
Capacitance
Shift
Insulation
Resistance
0.3% or ±0.25 pF 10% of Initial Limit
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1081_C0G_HV_FT_AUTO_SMD • 2/29/2016 5
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP), C0G Dielectric, 500 – 3,000 VDC (Automotive Grade)
Table 1A – Capacitance Range/Selection Waterfall (0805 – 1808 Case Sizes)
2500
3000
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LA
LA
LA
LA
LA
LA
LA
LB
LB
LB
LB
LB
LB
LC
LC
LC
LC
LA
LA
LA
LA
LA
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LC
LC
LC
LC
LC
LC
LC
LC
LA
LA
LA
LA
LB
LB
LC
LC
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LC
LC
LC
LC
LC
LC
LC
LC
LC
LC
LC
LC
LC
LC
LC
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LC
LC
LC
LC
2500
1000
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LA
LA
LA
LA
LA
LA
LA
LA
LA
LA
LA
LA
LA
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
3000
630
2000
500
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LA
LA
LA
LA
LA
LA
LA
LA
LA
LA
LA
LA
LA
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
2000
2000
1500
1500
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LA
LA
LA
LA
LA
LA
LA
LA
LA
LA
LA
LA
LA
LA
LA
LA
LA
LA
LB
LB
LB
LB
LB
1500
H
1000
Z
630
G
500
F
2000
D
G
C
B
D
F
G
Z
H
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EF
EF
EF
EF
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EF
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
EU
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FZ
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FK
FK
FK
FK
FK
FS
FS
FS
FS
FS
FS
FM
FM
FY
FY
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FK
FK
FK
FS
FS
FS
FS
FS
FS
FS
FS
630
1000
1500
B
B
500
C
Case Size/Series
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
C
2000
Voltage Code
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
G
1500
Rated Voltage (VDC)
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
F
1000
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
D
630
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
B
1000
500
D
C
500
C
G
1000
Cap Code
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
DG
630
Capacitance
B
500
109 - 169*
100
110
120
130
150
160
180
200
220
240
270
300
330
360
390
430
470
510
560
620
680
750
820
910
101
111
121
131
151
161
181
201
221
241
271
301
331
361
391
431
471
511
561
621
681
751
821
911
102
F
Product Availability and Chip Thickness Codes
See Table 2 for Chip Thickness Dimensions
Capacitance Tolerance
1.0 - 9.1 pF*
10 pF
11 pF
12 pF
13 pF
15 pF
16 pF
18 pF
20 pF
22 pF
24 pF
27 pF
30 pF
33 pF
36 pF
39 pF
43 pF
47 pF
51 pF
56 pF
62 pF
68 pF
75 pF
82 pF
91 pF
100 pF
110 pF
120 pF
130 pF
150 pF
160 pF
180 pF
200 pF
220 pF
240 pF
270 pF
300 pF
330 pF
360 pF
390 pF
430 pF
470 pF
510 pF
560 pF
620 pF
680 pF
750 pF
820 pF
910 pF
1,000 pF
D
630
Rated Voltage (VDC)
B
500
C
2000
D
1500
B
C1808X
1000
C
C1210X
630
Voltage Code
1000
Cap Code
C1206X
630
Capacitance
C0805X
500
Case Size/Series
D
C
B
D
F
G
C
B
D
F
C0805X
C1206X
C1210X
C1808X
*Capacitance range Includes E24 decade values only. (i.e., 10, 11, 12, 13, 15, 16, 18, 20, 22, 24, 27, 30, 33, 36, 39, 43, 47, 51, 56, 62, 68, 75, 82 and 91)
KEMET reserves the right to substitute product with an improved temperature characteristic, tighter capacitance tolerance and/or higher voltage capability within
the same form factor (configuration and dimensions).
These products are protected under US Patents 7,172,985 and 7,670,981, other patents pending, and any foreign counterparts..
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1081_C0G_HV_FT_AUTO_SMD • 2/29/2016 6
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP), C0G Dielectric, 500 – 3,000 VDC (Automotive Grade)
Table 1A – Capacitance Range/Selection Waterfall (0805 – 1808 Case Sizes) cont’d
1500
2500
1000
3000
630
2500
500
3000
2000
2000
1500
2000
1000
H
1500
630
Z
1000
500
G
630
F
500
D
2000
B
1500
C
1000
G
630
F
500
500
D
2000
1000
B
1500
630
C
2000
Cap Code
G
1500
Capacitance
112
122
132
152
162
182
202
222
242
272
302
332
362
392
432
472
512
562
622
682
752
822
F
Rated Voltage (VDC)
Voltage Code
C
B
D
C
B
D
F
G
C
B
D
F
G
C
B
D
F
G
Z
H
Capacitance Tolerance
1,100 pF
1,200 pF
1,300 pF
1,500 pF
1,600 pF
1,800 pF
2,000 pF
2,200 pF
2,400 pF
2,700 pF
3,000 pF
3,300 pF
3,600 pF
3,900 pF
4,300 pF
4,700 pF
5,100 pF
5,200 pF
6,200pF
6,800pF
7,500pF
8,200pF
D
1000
Rated Voltage (VDC)
B
1000
C
630
D
630
B
500
C
C1808X
1000
Voltage Code
C1210X
630
Cap Code
C1206X
500
Capacitance
C0805X
500
Case Size/Series
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
Case Size/Series
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
EF
EF
EF
EF
EF
EF
EU
EU
EU
EU
EQ
EQ
ER
ER
ES
ES
C0805X
Product Availability and Chip Thickness Codes
See Table 2 for Chip Thickness Dimensions
EU
EU
EU
EU
EU
EU
EQ
EQ
EQ
EQ
EQ
EQ
ER
ER
ES
ES
FM
FM
FM
FK
FK
FK
FK
FK
FS
FS
FS
FS
FL
FL
FM
FM
FY
FY
FY
FY
FS
FS
FK
FK
FS
FS
FS
FS
FL
FL
FL
FL
FL
FM
FM
FY
FY
FY
FS
FS
FE
FE
FK
FK
FS
FS
FS
FS
FS
FS
FS
FS
FS
FS
C1206X
C1210X
LC
LC
LC
LC
LC
LC
LC
LC
LC
LC
LA
LA
LA
LA
LA
LA
LA
LB
LC
LC
LC
LC
LC
LC
LC
LC
LA
LA
LA
LA
LA
LA
LB
LB
LC
LC
LC
LC
LC
LC
LC
LC
LB
LB
LB
LC
LB
LC
LC
LC
C1808X
*Capacitance range Includes E24 decade values only. (i.e., 10, 11, 12, 13, 15, 16, 18, 20, 22, 24, 27, 30, 33, 36, 39, 43, 47, 51, 56, 62, 68, 75, 82 and 91)
KEMET reserves the right to substitute product with an improved temperature characteristic, tighter capacitance tolerance and/or higher voltage capability within
the same form factor (configuration and dimensions).
These products are protected under US Patents 7,172,985 and 7,670,981, other patents pending, and any foreign counterparts..
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1081_C0G_HV_FT_AUTO_SMD • 2/29/2016 7
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP), C0G Dielectric, 500 – 3,000 VDC (Automotive Grade)
Table 1B – Capacitance Range/Selection Waterfall (1812 – 2225 Case Sizes)
2000
2500
3000
500
630
1000
1500
2000
2500
3000
500
630
1000
1500
2000
2500
3000
2500
1500
3000
630
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GH
GH
GH
GH
GH
GH
GK
GK
GK
GK
GH
GH
GH
GH
GH
GH
GH
GH
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GH
GH
GH
GH
GH
GH
GK
GK
GK
GK
GH
GH
GH
GH
GH
GH
GH
GH
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GH
GH
GH
GH
GH
GH
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GH
GH
GH
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GH
GH
GH
GH
GH
GH
GH
GK
GK
GK
GH
GH
GH
GH
GK
GK
GM
GM
GO
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GM
GM
GM
GO
Rated Voltage (VDC)
1500
2000
2500
Voltage Code
C
B
D
F
G
Z
H
C
B
D
F
G
Z
C1812X
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JE
JE
JE
JE
JE
JK
JK
JK
JE
JE
JE
JE
JE
JE
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JE
JE
JE
JE
JE
JK
JK
JK
JE
JE
JE
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JE
JE
JE
JE
JE
JK
JK
JK
JE
JE
JE
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JE
JE
JE
JE
JE
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JE
JE
JE
JE
JE
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JE
JK
JK
JL
JL
JL
JL
JN
JN
JN
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KE
KE
KE
KE
KE
KE
KE
KF
KF
KF
KF
KF
KE
KE
KE
KE
KE
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KE
KE
KE
KE
KE
KE
KE
KF
KF
KF
KF
KF
KE
KE
KE
KE
KE
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KE
KE
KE
KE
KE
KE
KE
KF
KF
KF
KF
KF
KE
KE
KE
KE
KE
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KE
KE
KE
KE
KE
KE
KE
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KH
KH
KH
KJ
KJ
KJ
H
C
B
D
F
G
Z
H
C
B
D
F
G
Z
H
Product Availability and Chip Thickness Codes
See Table 2 for Chip Thickness Dimensions
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GH
GH
GH
GH
GH
GH
GK
GK
GK
GK
GH
GH
GH
GH
GH
GH
GH
GH
GH
Case Size/Series
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GM
GM
GM
GM
GM
GO
GO
GO
3000
H
2000
Z
2500
G
2000
F
1500
D
1000
B
1500
C
1000
H
630
Z
500
G
630
F
500
D
3000
B
2500
C
2000
H
1500
Z
1000
G
630
F
500
D
3000
B
1000
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
C
630
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
H
500
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
Z
3000
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
2500
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
2000
Capacitance
Tolerance
D
1000
Rated Voltage (VDC)
C2225X
B
1500
Cap
Code
C
630
Cap
100
110
120
130
150
160
180
200
220
240
270
300
330
360
390
430
470
510
560
620
680
750
820
910
101
111
121
131
151
161
181
201
221
241
271
301
331
361
391
431
471
511
561
621
681
751
821
911
102
112
Voltage Code
C2220X
1000
10 pF
11 pF
12 pF
13 pF
15 pF
16 pF
18 pF
20 pF
22 pF
24 pF
27 pF
30 pF
33 pF
36 pF
39 pF
43 pF
47 pF
51 pF
56 pF
62 pF
68 pF
75 pF
82 pF
91 pF
100 pF
110 pF
120 pF
130 pF
150 pF
160 pF
180 pF
200 pF
220 pF
240 pF
270 pF
300 pF
330 pF
360 pF
390 pF
430 pF
470 pF
510 pF
560 pF
620 pF
680 pF
750 pF
820 pF
910 pF
1,000 pF
1,100 pF
Cap
Code
C1825X
500
Cap
C1812X
500
Case Size/Series
HJ
HJ
HJ
HJ
HK
HK
HJ
HJ
HJ
HJ
HK
HK
HJ
HJ
HJ
HJ
HK
HK
HJ
HJ
HJ
HJ
HK
HK
HJ
HJ
HJ
HJ
HK
HK
HJ
HJ
HJ
HJ
HK
HK
HJ
HJ
HJ
HJ
HK
HK
HJ HJ HJ HJ HJ HJ
C1825X
C2220X
C2225X
*Capacitance range Includes E24 decade values only. (i.e., 10, 11, 12, 13, 15, 16, 18, 20, 22, 24, 27, 30, 33, 36, 39, 43, 47, 51, 56, 62, 68, 75, 82 and 91)
KEMET reserves the right to substitute product with an improved temperature characteristic, tighter capacitance tolerance and/or higher voltage capability within
the same form factor (configuration and dimensions).
These products are protected under US Patents 7,172,985 and 7,670,981, other patents pending, and any foreign counterparts..
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1081_C0G_HV_FT_AUTO_SMD • 2/29/2016 8
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP), C0G Dielectric, 500 – 3,000 VDC (Automotive Grade)
Table 1B – Capacitance Range/Selection Waterfall (1812 – 2225 Case Sizes) cont’d
2500
H
C
B
D
F
G
Z
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JE
JK
JK
JL
JL
JL
JN
JK
JK
JK
JK
JK
JE
JE
JE
JE
JE
JK
JK
JK
JK
JL
JL
JN
JN
JN
JK JL
JE JL
JE JL
JE JL
JE JN
JK
JK
JL
JL
JL
JN
JN
JN
H
C
B
D
F
G
Z
C1825X
C2220X
3000
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KF
KF
KF
KF
KE
KE
KE
KF
KF
KH
KJ
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KF
KF
KF
KF
KF
KF
KF
KF
KE
KE
KE
KE
KE
KF
KH
KJ
KJ
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KE
KF
KF
KF
KF
KF
KF
KF
KF
KF
KF
KH
KH
KH
KJ
KF
KF
KF
KF
KF
KF
KF
KE
KE
KE
KE
KF
KF
KF
KH
KH
KH
KJ
KJ
KF
KF
KF
KE
KE
KE
KF
KH
KH
KH
KJ
KJ
KJ
KF
KH
KH
KH
KH
KJ
KJ
3000
Z
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JE
JE
JE
JE
JE
JE
JK
JL
JL
JN
JN
2500
G
JE
JE
JE
JE
JE
JE
JE
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JK
JE
JE
JE
JE
JE
JK
JL
JN
2000
F
HJ
HJ
HK
HK
1500
D
HJ
HE
HE
HG
HG
HJ
HJ
HJ
HK
HK
1000
B
HJ
HE
HE
HG
HG
HE
HE
HE
HE
HE
HG
HG
HJ
HJ
HJ
HK
HK
630
C
HJ
HE
HE
HG
HG
HE
HE
HE
HE
HE
HG
HG
HJ
HJ
HJ
HG
HG
HG
HJ
HJ
HJ
HK
HK
500
Voltage Code
HJ
HE
HE
HG
HG
HE
HE
HE
HE
HE
HG
HG
HJ
HJ
HJ
HE
HE
HE
HE
HE
HE
HG
HG
HG
HJ
HK
3000
Rated Voltage (VDC)
HJ
HE
HE
HG
HG
HE
HE
HE
HE
HE
HG
HG
HJ
HJ
HJ
HE
HE
HE
HE
HE
HE
HE
HE
HE
HE
HG
HJ
HJ
HK
2500
GH GO
GH GO
GK GO
GK
GM
GM
GO
GO
GO
2000
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GM
GM
GO
GO
GO
GO
H
2000
Z
2500
G
2000
F
1500
2000
D
1000
1500
B
1500
1000
C
1000
630
H
630
500
Z
500
G
630
F
500
D
2500
B
3000
C
3000
H
3000
500
Z
2500
3000
G
2000
2500
F
1500
2000
1000
1500
630
630
1000
GK
GK
GK
GK
GK
GK
GK
GH
GH
GH
GH
GH
GH
GH
GH
GK
GK
GK
GM
GM
GO
GO
GO
C1812X
D
C2225X
H
C
B
D
F
G
Z
H
Product Availability and Chip Thickness Codes
See Table 2 for Chip Thickness Dimensions
GH
GH
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GK
GH
GH
GH
GH
GH
GH
GH
GK
GM
GM
GO
GO
Case Size/Series
B
1500
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
C
1000
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
H
630
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
Z
500
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
C2220X
3000
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
2500
Capacitance
Tolerance
D
2000
Cap
Cap
Code
Rated Voltage (VDC)
B
1500
122
132
152
162
182
202
222
242
272
302
332
362
392
432
472
512
562
622
682
752
822
912
103
123
153
183
223
273
333
393
C
630
1,200 pF
1,300 pF
1,500 pF
1,600 pF
1,800 pF
2,000 pF
2,200 pF
2,400 pF
2,700 pF
3,000 pF
3,300 pF
3,600 pF
3,900 pF
4,300 pF
4,700 pF
5,100 pF
5,600 pF
6,200 pF
6,800 pF
7,500 pF
8,200 pF
9,100 pF
10,000 pF
12,000 pF
15,000 pF
18,000 pF
22,000 pF
27,000 pF
33,000 pF
39,000 pF
Voltage Code
1000
Cap
Code
C1825X
500
Cap
C1812X
500
Case Size/Series
C2225X
*Capacitance range Includes E24 decade values only. (i.e., 10, 11, 12, 13, 15, 16, 18, 20, 22, 24, 27, 30, 33, 36, 39, 43, 47, 51, 56, 62, 68, 75, 82 and 91)
KEMET reserves the right to substitute product with an improved temperature characteristic, tighter capacitance tolerance and/or higher voltage capability within
the same form factor (configuration and dimensions).
These products are protected under US Patents 7,172,985 and 7,670,981, other patents pending, and any foreign counterparts..
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1081_C0G_HV_FT_AUTO_SMD • 2/29/2016 9
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP), C0G Dielectric, 500 – 3,000 VDC (Automotive Grade)
Table 2 – Chip Thickness/Tape & Reel Packaging Quantities
Paper Quantity
Plastic Quantity
Thickness
Code
Case
Size
Thickness ±
Range (mm)
7" Reel
13" Reel
7" Reel
13" Reel
DG
EQ
EF
EU
ER
ES
FE
FZ
FL
FM
FY
FK
FS
LA
LB
LC
GH
GK
GM
GO
HE
HG
HJ
HK
JE
JK
JL
JN
KE
KF
KH
KJ
805
1206
1206
1206
1206
1206
1210
1210
1210
1210
1210
1210
1210
1808
1808
1808
1812
1812
1812
1812
1825
1825
1825
1825
2220
2220
2220
2220
2225
2225
2225
2225
1.25 ± 0.15
0.78 ± 0.20
1.20 ± 0.15
1.60 ± 0.25
0.90 ± 0.20
1.00 ± 0.20
1.00 ± 0.10
1.25 ± 0.20
1.40 ± 0.15
1.70 ± 0.20
2.00 ± 0.20
2.10 ± 0.20
2.50 ± 0.30
1.40 ± 0.15
1.60 ± 0.15
2.00 ± 0.15
1.40 ± 0.15
1.60 ± 0.20
2.00 ± 0.20
2.50 ± 0.20
1.40 ± 0.15
1.60 ± 0.20
2.00 ± 0.20
2.50 ± 0.20
1.40 ± 0.15
1.60 ± 0.20
2.00 ± 0.20
2.50 ± 0.20
1.40 ± 0.15
1.60 ± 0.20
2.00 ± 0.20
2.50 ± 0.20
0
4000
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
10000
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
2,500
4,000
2,500
2,000
4,000
2,500
2,500
2,500
2,000
2,000
2,000
2,000
1,000
1,000
1,000
1,000
1,000
1,000
500
500
1,000
1,000
500
500
1,000
1,000
500
500
1,000
1,000
500
500
10,000
10,000
10,000
8,000
10,000
10,000
10,000
10,000
8,000
8,000
8,000
8,000
4,000
4,000
4,000
4,000
4,000
4,000
2,000
2,000
4,000
4,000
2,000
2,000
4,000
4,000
2,000
2,000
4,000
4,000
2,000
2,000
Thickness
Code
Case
Size
Thickness ±
Range (mm)
7" Reel
13" Reel
7" Reel
13" Reel
Paper Quantity
Plastic Quantity
Package quantity based on finished chip thickness specifications.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1081_C0G_HV_FT_AUTO_SMD • 2/29/2016 10
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP), C0G Dielectric, 500 – 3,000 VDC (Automotive Grade)
Table 3 – Chip Capacitor Land Pattern Design Recommendations per IPC–7351
EIA
Size
Code
Metric
Size
Code
0805
Density Level A:
Maximum (Most)
Land Protrusion (mm)
Density Level B:
Median (Nominal)
Land Protrusion (mm)
Density Level C:
Minimum (Least)
Land Protrusion (mm)
C
Y
X
V1
V2
C
Y
X
V1
V2
C
Y
X
V1
V2
2012
0.99
1.44
1.66
4.47
2.71
0.89
1.24
1.56
3.57
2.11
0.79
1.04
1.46
2.42
1.81
1206
3216
1.59
1.62
2.06
5.85
3.06
1.49
1.42
1.96
4.95
2.46
1.39
1.22
1.86
4.25
2.16
1210
3225
1.59
1.62
3.01
5.90
4.01
1.49
1.42
2.91
4.95
3.41
1.39
1.22
2.81
4.25
3.11
1808
4520
2.30
1.75
2.30
7.40
3.30
2.20
1.55
2.20
6.50
2.70
2.10
1.35
2.10
5.80
2.40
1812
4532
2.10
1.80
3.60
7.00
4.60
2.00
1.60
3.50
6.10
4.00
1.90
1.40
3.40
5.40
3.70
1825
4564
2.15
1.80
6.90
7.10
7.90
2.05
1.60
6.80
6.20
7.30
1.95
1.40
6.70
5.50
7.00
2220
5650
2.85
2.10
5.50
8.80
6.50
2.75
1.90
5.40
7.90
5.90
2.65
1.70
5.30
7.20
5.60
2225
5664
2.85
2.10
6.90
8.80
7.90
2.75
1.90
6.80
7.90
7.30
2.65
1.70
6.70
7.20
7.00
Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder
processes. KEMET only recommends wave soldering of EIA 0603, 0805 and 1206 case sizes.
Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes.
Density Level C: For high component density product applications. Before adapting the minimum land pattern variations the user should perform qualification
testing based on the conditions outlined in IPC Standard 7351 (IPC–7351).
Image below based on Density Level B for an EIA 1210 case size.
V1
Y
Y
X
C
V2
X
C
Grid Placement Courtyard
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1081_C0G_HV_FT_AUTO_SMD • 2/29/2016 11
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP), C0G Dielectric, 500 – 3,000 VDC (Automotive Grade)
Soldering Process
Recommended Soldering Technique:
• Solder wave or solder reflow for EIA case sizes 0603, 0805 and 1206
• All other EIA case sizes are limited to solder reflow only
Recommended Reflow Soldering Profile:
KEMET’s families of surface mount multilayer ceramic capacitors (SMD MLCCs) are compatible with wave (single or dual), convection,
IR or vapor phase reflow techniques. Preheating of these components is recommended to avoid extreme thermal stress. KEMET’s
recommended profile conditions for convection and IR reflow reflect the profile conditions of the IPC/J-STD-020 standard for moisture
sensitivity testing. These devices can safely withstand a maximum of three reflow passes at these conditions.
Termination Finish
Preheat/Soak
Temperature Minimum (TSmin)
Temperature Maximum (TSmax)
Time (tS) from TSmin to TSmax
Ramp-Up Rate (TL to TP)
SnPb
100% Matte Sn
100°C
150°C
60 – 120 seconds
150°C
200°C
60 – 120 seconds
183°C
217°C
Time Above Liquidous (tL)
60 – 150 seconds
60 – 150 seconds
Peak Temperature (TP)
235°C
260°C
Time Within 5°C of Maximum
Peak Temperature (tP)
20 seconds maximum
30 seconds maximum
Time 25°C to Peak
Temperature
TL
tP
Maximum Ramp Up Rate = 3°C/sec
Maximum Ramp Down Rate = 6°C/sec
tL
Tsmax
Tsmin
tS
3°C/second maximum 3°C/second maximum
Liquidous Temperature (TL)
Ramp-Down Rate (TP to TL)
TP
Temperature
Profile Feature
25
25° C to Peak
Time
6°C/second maximum 6°C/second maximum
6 minutes maximum
8 minutes maximum
Note 1: All temperatures refer to the center of the package, measured on the
capacitor body surface that is facing up during assembly reflow.
Storage and Handling
Ceramic chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in other
environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term
storage. In addition, packaging materials will be degraded by high temperature– reels may soften or warp and tape peel force may
increase. KEMET recommends that maximum storage temperature not exceed 40ºC and maximum storage humidity not exceed 70%
relative humidity. Temperature fluctuations should be minimized to avoid condensation on the parts and atmospheres should be free of
chlorine and sulfur bearing compounds. For optimized solderability chip stock should be used promptly, preferably within 1.5 years of
receipt.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1081_C0G_HV_FT_AUTO_SMD • 2/29/2016 12
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP), C0G Dielectric, 500 – 3,000 VDC (Automotive Grade)
Construction
Detailed Cross Section
Dielectric Material
(CaZrO3)
End Termination/
External Electrode
(Cu)
Epoxy Layer
(Ag)
Dielectric Material
(CaZrO3)
Barrier Layer
(Ni)
Termination Finish
(100% Matte Sn)
Inner Electrodes
(Ni)
End Termination/
External Electrode
(Cu)
Epoxy Layer
(Ag)
Barrier Layer
(Ni)
Inner Electrodes
(Ni)
Termination Finish
(100% Matte Sn)
Capacitor Marking (Optional):
Laser marking option is not available on:
•
•
•
•
C0G, Ultra Stable X8R and Y5V dielectric devices
EIA 0402 case size devices
EIA 0603 case size devices with Flexible Termination option.
KPS Commercial and Automotive grade stacked devices.
These capacitors are supplied unmarked only.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1081_C0G_HV_FT_AUTO_SMD • 2/29/2016 13
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP), C0G Dielectric, 500 – 3,000 VDC (Automotive Grade)
Tape & Reel Packaging Information
KEMET offers multilayer ceramic chip capacitors packaged in 8, 12 and 16 mm tape on 7" and 13" reels in accordance with EIA
Standard 481. This packaging system is compatible with all tape-fed automatic pick and place systems. See Table 2 for details on
reeling quantities for commercial chips.
Bar Code Label
Anti-Static Reel
®
Embossed Plastic* or
Punched Paper Carrier.
ET
KEM
Chip and KPS Orientation in Pocket
(except 1825 Commercial, and 1825 and 2225 Military)
Sprocket Holes
Embossment or Punched Cavity
8 mm, 12 mm
or 16 mm Carrier Tape
178 mm (7.00")
or
330 mm (13.00")
Anti-Static Cover Tape
(.10 mm (.004") Maximum Thickness)
*EIA 01005, 0201, 0402 and 0603 case sizes available on punched paper carrier only.
Table 5 – Carrier Tape Configuration, Embossed Plastic & Punched Paper (mm)
EIA Case Size
Tape
Size
(W)*
Embossed Plastic
7" Reel
13" Reel
Punched Paper
7" Reel
Pitch (P1)*
13" Reel
Pitch (P1)*
01005 – 0402
8
2
2
0603
8
2/4
2/4
0805
8
4
4
4
4
1206 – 1210
8
4
4
4
4
1805 – 1808
12
4
4
≥ 1812
12
8
8
KPS 1210
12
8
8
KPS 1812 & 2220
16
12
12
Array 0508 & 0612
8
4
4
*Refer to Figures 1 & 2 for W and P1 carrier tape reference locations.
*Refer to Tables 6 & 7 for tolerance specifications.
New 2 mm Pitch Reel Options*
Packaging
Ordering Code
(C-Spec)
C-3190
C-3191
C-7081
C-7082
Packaging Type/Options
Automotive grade 7" reel unmarked
Automotive grade 13" reel unmarked
Commercial grade 7" reel unmarked
Commercial grade 13" reel unmarked
* 2 mm pitch reel only available for 0603 EIA case size.
2 mm pitch reel for 0805 EIA case size under development.
Benefits of Changing from 4 mm to 2 mm Pitching Spacing
• Lower placement costs
• Double the parts on each reel results in fewer reel
changes and increased efficiency
• Fewer reels result in lower packaging, shipping and
storage costs, reducing waste
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1081_C0G_HV_FT_AUTO_SMD • 2/29/2016 14
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP), C0G Dielectric, 500 – 3,000 VDC (Automotive Grade)
Figure 1 – Embossed (Plastic) Carrier Tape Dimensions
P2
T
T2
ØDo
[10 pitches cumulative
tolerance on tape ± 0.2 mm]
Po
E1
Ao
F
Ko
B1
E2
Bo
S1
W
P1
T1
Center Lines of Cavity
ØD 1
Cover Tape
B 1 is for tape feeder reference only,
including draft concentric about B o.
Embossment
For cavity size,
see Note 1 Table 4
User Direction of Unreeling
Table 6 – Embossed (Plastic) Carrier Tape Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
Tape Size
D0
8 mm
12 mm
1.5 +0.10/-0.0
(0.059 +0.004/-0.0)
16 mm
D1 Minimum
Note 1
1.0
(0.039)
1.5
(0.059)
E1
P0
1.75 ±0.10
(0.069 ±0.004)
4.0 ±0.10
(0.157 ±0.004)
R Reference S1 Minimum
Note 2
Note 3
25.0
(0.984)
2.0 ±0.05
0.600
(0.079 ±0.002)
(0.024)
30
(1.181)
P2
T
Maximum
T1
Maximum
0.600
(0.024)
0.100
(0.004)
Variable Dimensions — Millimeters (Inches)
Tape Size
Pitch
8 mm
Single (4 mm)
12 mm
Single (4 mm) &
Double (8 mm)
16 mm
Triple (12 mm)
B1 Maximum
Note 4
4.35
(0.171)
8.2
(0.323)
12.1
(0.476)
E2
Minimum
6.25
(0.246)
10.25
(0.404)
14.25
(0.561)
F
P1
3.5 ±0.05
(0.138 ±0.002)
5.5 ±0.05
(0.217 ±0.002)
7.5 ±0.05
(0.138 ±0.002)
4.0 ±0.10
(0.157 ±0.004)
8.0 ±0.10
(0.315 ±0.004)
12.0 ±0.10
(0.157 ±0.004)
T2
Maximum
2.5
(0.098)
4.6
(0.181)
4.6
(0.181)
W
Maximum
8.3
(0.327)
12.3
(0.484)
16.3
(0.642)
A0,B0 & K0
Note 5
1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and
hole location shall be applied independent of each other.
2. The tape with or without components shall pass around R without damage (see Figure 6).
3. If S1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481 paragraph 4.3 section b).
4. B1 dimension is a reference dimension for tape feeder clearance only.
5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that:
(a) the component does not protrude above the top surface of the carrier tape.
(b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
(c) rotation of the component is limited to 20° maximum for 8 and 12 mm tapes and 10° maximum for 16 mm tapes (see Figure 3).
(d) lateral movement of the component is restricted to 0.5 mm maximum for 8 and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see Figure 4).
(e) for KPS Series product, A0 and B0 are measured on a plane 0.3 mm above the bottom of the pocket.
(f) see Addendum in EIA Standard 481 for standards relating to more precise taping requirements.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1081_C0G_HV_FT_AUTO_SMD • 2/29/2016 15
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP), C0G Dielectric, 500 – 3,000 VDC (Automotive Grade)
Figure 2 – Punched (Paper) Carrier Tape Dimensions
P2
T
Po
ØDo
[10 pitches cumulative
tolerance on tape ± 0.2 mm]
A0
F
P1
T1
T1
Top Cover Tape
W
E2
B0
Bottom Cover Tape
E1
G
Cavity Size,
See
Note 1, Table 7
Center Lines of Cavity
Bottom Cover Tape
User Direction of Unreeling
Table 7 – Punched (Paper) Carrier Tape Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
Tape Size
D0
E1
P0
P2
8 mm
1.5 +0.10 -0.0
(0.059 +0.004 -0.0)
1.75 ±0.10
(0.069 ±0.004)
4.0 ±0.10
(0.157 ±0.004)
2.0 ±0.05
(0.079 ±0.002)
G Minimum
0.10
(0.004)
Maximum
R Reference
Note 2
0.75
(0.030)
25
(0.984)
T Maximum
W Maximum
A0 B 0
1.1
(0.098)
8.3
(0.327)
8.3
(0.327)
T1 Maximum
Variable Dimensions — Millimeters (Inches)
Tape Size
Pitch
8 mm
Half (2 mm)
8 mm
Single (4 mm)
E2 Minimum
6.25
(0.246)
F
3.5 ±0.05
(0.138 ±0.002)
P1
2.0 ±0.05
(0.079 ±0.002)
4.0 ±0.10
(0.157 ±0.004)
Note 1
1. The cavity defined by A0, B0 and T shall surround the component with sufficient clearance that:
a) the component does not protrude beyond either surface of the carrier tape.
b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
c) rotation of the component is limited to 20° maximum (see Figure 3).
d) lateral movement of the component is restricted to 0.5 mm maximum (see Figure 4).
e) see Addendum in EIA Standard 481 for standards relating to more precise taping requirements.
2. The tape with or without components shall pass around R without damage (see Figure 6).
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1081_C0G_HV_FT_AUTO_SMD • 2/29/2016 16
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP), C0G Dielectric, 500 – 3,000 VDC (Automotive Grade)
Packaging Information Performance Notes
1. Cover Tape Break Force: 1.0 Kg minimum.
2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be:
Tape Width
Peel Strength
8 mm
0.1 to 1.0 Newton (10 to 100 gf)
12 and 16 mm
0.1 to 1.3 Newton (10 to 130 gf)
The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165° to 180°
from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 ±10 mm/minute.
3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA
Standards 556 and 624.
Figure 3 – Maximum Component Rotation
°
T
Maximum Component Rotation
Top View
Maximum Component Rotation
Side View
Typical Pocket Centerline
Tape
Width (mm)
8,12
16 – 200
Bo
Maximum
Rotation (
20
10
°
T)
Typical Component Centerline
Ao
Figure 4 – Maximum Lateral Movement
8 mm & 12 mm Tape
0.5 mm maximum
0.5 mm maximum
16 mm Tape
°
s
Tape
Maximum
Width (mm) Rotation (
8,12
20
16 – 56
10
72 – 200
5
°
S)
Figure 5 – Bending Radius
Embossed
Carrier
Punched
Carrier
1.0 mm maximum
1.0 mm maximum
R
Bending
Radius
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
R
C1081_C0G_HV_FT_AUTO_SMD • 2/29/2016 17
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP), C0G Dielectric, 500 – 3,000 VDC (Automotive Grade)
Figure 6 – Reel Dimensions
Full Radius,
See Note
W3 (Includes
Access Hole at
Slot Location
(Ø 40 mm minimum)
flange distortion
at outer edge)
W2 (Measured at hub)
D
A
(See Note)
N
C
(Arbor hole
diameter)
B
(see Note)
W1 (Measured at hub)
If present,
tape slot in core
for tape start:
2.5 mm minimum width x
10.0 mm minimum depth
Note: Drive spokes optional; if used, dimensions B and D shall apply.
Table 8 – Reel Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
Tape Size
A
B Minimum
C
D Minimum
8 mm
178 ±0.20
(7.008 ±0.008)
or
330 ±0.20
(13.000 ±0.008)
1.5
(0.059)
13.0 +0.5/-0.2
(0.521 +0.02/-0.008)
20.2
(0.795)
12 mm
16 mm
Variable Dimensions — Millimeters (Inches)
Tape Size
N Minimum
W1
W2 Maximum
W3
50
(1.969)
8.4 +1.5/-0.0
(0.331 +0.059/-0.0)
12.4 +2.0/-0.0
(0.488 +0.078/-0.0)
16.4 +2.0/-0.0
(0.646 +0.078/-0.0)
14.4
(0.567)
18.4
(0.724)
22.4
(0.882)
Shall accommodate tape width
without interference
8 mm
12 mm
16 mm
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1081_C0G_HV_FT_AUTO_SMD • 2/29/2016 18
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP), C0G Dielectric, 500 – 3,000 VDC (Automotive Grade)
Figure 7 – Tape Leader & Trailer Dimensions
Embossed Carrier
Carrier Tape
Punched Carrier
8 mm & 12 mm only
END
Round Sprocket Holes
START
Top Cover Tape
Elongated Sprocket Holes
(32 mm tape and wider)
Trailer
160 mm Minimum
Components
100 mm
Minimum Leader
400 mm Minimum
Top Cover Tape
Figure 8 – Maximum Camber
Elongated sprocket holes
(32 mm & wider tapes)
Carrier Tape
Round Sprocket Holes
1 mm Maximum, either direction
Straight Edge
250 mm
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1081_C0G_HV_FT_AUTO_SMD • 2/29/2016 19
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP), C0G Dielectric, 500 – 3,000 VDC (Automotive Grade)
KEMET Corporation
World Headquarters
Europe
Asia
Southern Europe
Sasso Marconi, Italy
Tel: 39-051-939111
Northeast Asia
Hong Kong
Tel: 852-2305-1168
Mailing Address:
P.O. Box 5928
Greenville, SC 29606
Skopje, Macedonia
Tel: 389-2-55-14-623
Shenzhen, China
Tel: 86-755-2518-1306
www.kemet.com
Tel: 864-963-6300
Fax: 864-963-6521
Central Europe
Landsberg, Germany
Tel: 49-8191-3350800
Corporate Offices
Fort Lauderdale, FL
Tel: 954-766-2800
Kamen, Germany
Tel: 49-2307-438110
North America
Northern Europe
Wyboston, United Kingdom
Tel: 44-1480-273082
Taipei, Taiwan
Tel: 886-2-27528585
Espoo, Finland
Tel: 358-9-5406-5000
Southeast Asia
Singapore
Tel: 65-6701-8033
2835 KEMET Way
Simpsonville, SC 29681
Northeast
Wilmington, MA
Tel: 978-658-1663
Southeast
Lake Mary, FL
Tel: 407-855-8886
Central
Novi, MI
Tel: 248-994-1030
Beijing, China
Tel: 86-10-5877-1075
Shanghai, China
Tel: 86-21-6447-0707
Seoul, South Korea
Tel: 82-2-6294-0550
Penang, Malaysia
Tel: 60-4-6430200
Bangalore, India
Tel: 91-806-53-76817
Irving, TX
Tel: 972-915-6041
West
Milpitas, CA
Tel: 408-433-9950
Mexico
Guadalajara, Jalisco
Tel: 52-33-3123-2141
Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not
assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of
KEMET Electronics Corporation.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1081_C0G_HV_FT_AUTO_SMD • 2/29/2016 20
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Voltage with Flexible Termination System (HV FT-CAP), C0G Dielectric, 500 – 3,000 VDC (Automotive Grade)
Disclaimer
All product specifications, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and
verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.
All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are
not intended to constitute – and KEMET specifically disclaims – any warranty concerning suitability for a specific customer application or use. The Information is intended for use only
by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise
provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained.
Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still
occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective
circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage.
Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not
be required.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1081_C0G_HV_FT_AUTO_SMD • 2/29/2016 21