FUJITSU SEMICONDUCTOR DATA SHEET DS07-12548-3E 8-bit Original Microcontroller CMOS F2MC-8L MB89530 Series MB89537/537C/538/538C MB89F538L/P538/PV530 ■ DESCRIPTION The MB89530 series is a one-chip microcontroller featuring the F2MC-8L core supporting low-voltage and highspeed operation. Built-in peripheral functions include timers, serial interface, A/D converter, and external interrupt. This product is an ideal general-purpose one-chip microcontroller for a wide variety of applications from household to industrial equipment, as well as use in portable devices. ■ FEATURES • Wide range of package options • QFP package (1mm pitch) • Two types of LQFP packages (0.5mm pitch, 0.65mm pitch) • SH-DIP package • BCC package (0.5mm pitch) • Low voltage, high-speed operating capability • Minimum instruction execution time 0.32 µs (at base oscillator 12.5MHz) • F2MC-8L CPU Core • Instruction set optimized for controller operation • Multiplication/division instructions • 16-bit calculation • Branching instructions with bit testing • Bit operation instructions, etc. • Five timer systems • 8-bit PWM timer with 2 channels (usable as either interval timer of PWM timer) • Pulse width count timer (supports continuous measurement or remote control receiving applications) • 16-bit timer counter • 21-bit time base timer • Watch prescaler (17-bit) • UART • Synchronous or asynchronous operation, switchable • 2 serial interfaces (serial I/O) • Selection of transfer direction (specify MSB first or LSB first) for communication with a variety of devices (Continued) MB89530 Series (Continued) • 10-bit A/D converter (8 channels) • External clock input for startup support (except for MB89F538L) • Time base timer output for startup support • Pulse generators (PPG) with 2-program capability • 6-bit PPG with selection of pulse width and pulse period • 12-bit PPG (2 channels) with selection of pulse width and pulse period • I2C interface circuits • External interrupt 1 (single-clock : 4 channels, dual-clock : 3 channels) • 4 or 3 independent inputs, release enabled from standby mode (includes edge detection function) • External interrupt 2 (except for MB89F538L : 8 channels, MB89F538L : 7 channels) • 8 or 7 independent inputs, release enabled form standby mode (includes level edge detection function) • Standby modes (low power consumption modes) • Stop mode (oscillator stops, virtually no power consumed) • Sleep mode (CPU stops, power consumption reduced to one-third) • Sub clock mode • Watch mode • Watchdog timer reset • I/O ports • Maximum port single-clock : except for MB89F538L : 53 MB89F538L : 52 dual-clock : except for MB89F538L : 51 MB89F538L : 50 • 38 general-purpose I/O ports (CMOS) (MB89F538L : 37) • 2 general-purpose I/O ports (N-ch open drain) • 8 general-purpose output ports (N-ch open drain) • General-purpose input ports(CMOS)single-clock : except for MB89F538L : 5 dual-clock : except for MB89F538L : 3 2 MB89530 Series ■ PACKAGES 64-pin, Plastic SH-DIP 64-pin, Plastic LQFP 64-pin, Plastic QFP (DIP-64P-M01) (FPT-64P-M03) (FPT-64P-M06) 64-pin, Plastic LQFP 64-pin, Ceramic MDIP 64-pin, Ceramic MQFP (FPT-64P-M09) (MDP-64C-P02) (MQP-64C-P01) 64-pin, Plastic BCC (LCC-64P-M19) (LCC-64P-M16) 3 MB89530 Series ■ PRODUCT LINEUP Part number Parameter Type MB89537/ 537C MB89538/ 538C MB89F538L MB89P538 MB89PV530 FLASH One-time programmable Evaluation 48 K × 8-bit (built-in FLASH memory) (write from general purpose EPROM writer) 48 K × 8-bit (built-in ROM) (write from general purpose EPROM writer) 48 K × 8-bit (external ROM) *2 Mass produced (Mask ROM) ROM capacity 32 K × 8-bit (built-in ROM) RAM capacity 1 K × 8-bit 48 K × 8-bit (built-in ROM) Operating voltage 2.2 V to 3.6 V*1 (MB89537/538/ 537C/538C) CPU functions Basic instructions Instruction bit length Instruction length Data bit length Minimum instruction execution time Minimum interrupt processing time 2 K × 8-bit 2.4 V to 3.6 V*1 2.7 V to 5.5 V : 136 : 8-bits : 1 bit to 3 bits : 1, 8, 16-bits : 0.32 µs / 12.5 MHz : 2.88 µs / 12.5 MHz Input ports Peripheral functions Ports : single-clock 5 (4 also usable as external interrupts) dual-clock 3 (3 also usable as external interrupts) Output-only ports (N-ch open drain) : 8 (8 also usable as ADC input) I/O ports (N-ch open drain) : 2 (2 also usable as SO2/SDA or SI2/SCL) I/O ports (CMOS) : 38 (21 have no other function) (except for MB89F538L) I/O ports (CMOS) : 37 (21 have no other function) (MB89F538L) Total (except for MB89F538L) : single-clock 53, 2system clock 51 Total (MB89F538L) : single-clock 52, 2system clock 50 21 bits Time base timer Interrupt periods at main clock oscillation frequency of 12.5MHz (approx. 0.655 ms, 2.621 ms, 20.97 ms, 335.5 ms) Watchdog timer Reset period of approx. 167.8 ms to 335.6 ms at mail clock frequency of 12.5 MHz Reset period of approx. 500 ms to 1000 ms at sub clock frequency of 32.768 kHz. PWM timer 8-bit interval timer operation (supports square wave output, operating clock period : 1, 8, 16, 64 tinst*3) Pulse width measurement with 8-bit resolution (conversion period : 28 tinst*3 to 28 × 64 tinst*3) 2 channels (can also be used as interval timer, can also be used as ch1 output and ch2 count clock) Watch prescaler Interval times at 17-bit sub clock base frequency of 32.768 kHz (approx. 31.25 ms, 0.25 s, 0.50 s, 1.00 s, 2.00 s, 4.00 s) (Continued) 4 MB89530 Series (Continued) Part number Peripheral functions Parameter MB89537/537C MB89538/538C MB89F538L MB89P538 MB89PV530 Pulse width count timer 8-bit one-shot timer operation (supports underflow output, operating clock period : 1, 4, 32 tinst*3, external) 8-bit reload timer operation (supports square wave output, operating clock period : 1, 4, 32 tinst*3, external) 8-bit pulse width measurement operation (continuous measurement, H width measurement, L width measurement, rise-to-rise, fallto-fall, H width measurement and rise-to-rise) 16-bit timer/ counter 16-bit timer operation (operating clock period : 1 tinst*3, external) 16-bit event counter operation (select rising, falling, or both edges) 16-bit × 1 ch Serial I/O 8 bit length, Selection of LSB first or MSB first, Transfer clock (2, 8, 32 tinst*3, external) UART/SIO CLK synchronous/CLK asynchronous data transfer capability (8, 9 bit with parity bit, or 7,8 bit without parity bit) . Built-in baud rate generator provides selection of 14 baud rate settings. UART CLK synchronous/CLK asynchronous data transfer capability (4, 6, 7, 8 bit with parity bit, or 5, 7, 8, 9 bit without parity bit) . Built-in baud rate generator provides selection of 14 baud rate settings. External clock output, 2-channel 8-bit PWM timer output also available for baud rate settings. External interrupt 1 Single-clock : 4-channel independent, dual-clock : 3-channel independent Selection of rising, falling, or both edge detection. Can be used for recovery from standby mode (edge detection also available in stop mode) . External interrupt 2 Except for MB89F538L : 8-channel independent L level detection, MB89F538L : 7-channel independent L level detection Can be used for recovery from standby mode. 6-bit PPG, 12-bit PPG Can generate square wave signals with programmable period. 6-bit × 1 channel or 12-bit × 2 channels. 1-channel , compatible with Intel System Administrator bus version 1.0 and Philips I2C I2C bus interface specifications. 2-line communications (on MB89PV530/P538/F538L/537C/538C) A/D converter 10-bit resolution × 8 channels. A/D conversion functions (conversion time : 60 tinst *3) Supports repeated calls from external clock (except for MB89F538L) Supports repeated calls from internal clock. Standard voltage input provided (AVR) Standby modes (power saving modes) Sleep mode, stop mode, sub clock mode, watch mode. Process CMOS *1 : Depends on operating frequency. *2 : Using external ROM and MBM27C512. *3 : tinst represents instruction execution time. This can be selected as 1/4, 1/8, 1/16, 1/64 of the main clock cycle or 1/2 of the sub clock cycle. Note : MB89537/538 have no built-in I2C functions. To use I2C functions, choose the MB89PV530/P538/F538L/MB89537C/538C. 5 MB89530 Series ■ MODEL DIFFERENCES AND SELECTION CONSIDERATIONS Part number Package MB89537/537C MB89538/538C MB89F538L MB89P538 MB89PV530 DIP-64P-M01 O O O O X FPT-64P-M03 O O X X X FPT-64P-M06 O O O O X FPT-64P-M09 O O O O X LCC-64P-M19 X X O X X LCC-64P-M16 X X X O* X MDP-64C-P02 X X X X O MQP-64C-P01 X X X X O O : Model-package combination available X : Model-package combination not available * : Only for ES Conversion sockets for pin pitch conversion (manufactured by Sunhayato Corp.) can be used. Contact : Sunhayato Corp. : TEL : +81-3-3984-7791 FAX : +81-3-3971-0535 E-mail : [email protected] 6 MB89530 Series ■ DIFFERENCES AMONG PRODUCTS 1. Memory Capacity When this product is used in a piggy-back or other evaluation configuration, it is necessary to carefully confirm the differences between the model being used and the product it is evaluating. Particular attention should be given to the following (see " CPU core 1. Memory Space") . • The program ROM area starts from address 4000H on the MB89P538, MB89F538L and MB89PV530 models. • Note upper limits on RAM, such as stack areas, etc. 2. Current Consumption • On the MB89PV530, the additional current consumed by the EPROM is added at the connecting socket on the back side. • When operating at low speed, the current consumption in the one-time PROM or EPROM models is greater than on the mask ROM models. However, current consumption in sleep or stop modes is identical. For details, refer to “ ELECTRICAL CHARACTERISTICS”. 3. Mask Options The options available for use, and the method of specifying options, differ according to the model. Before use, check the “ MASK OPTIONS” specification section. 4. Wild Register Functions The following table shows areas in which wild register functions can be used. Wild Register Usage Areas Part number Address space MB89PV530 4000H to FFFFH MB89P538 4000H to FFFFH MB89F538L 4000H to FFFFH MB89537/537C 8000H to FFFFH MB89538/538C 4000H to FFFFH 7 MB89530 Series ■ PIN ASSIGNMENTS (TOP VIEW) P36/WTO P37/PTO1 P40/INT20/EC P41/INT21/SCK2 P42/INT22/SO2/SDA P43/INT23/SI2/SCL P44/INT24/UCK2 P45/INT25/UO2 P46/INT26/UI2 P47/INT27/ADST/MOD2*2 P50/AN0 P51/AN1 P52/AN2 P53/AN3 P54/AN4 P55/AN5 P56/AN6 P57/AN7 AVCC AVR AVSS P60/INT10 P61/INT11 P62/INT12 P63/INT13/X0A*3 P64/X1A*3 RST MOD0 MOD1 X0 X1 VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 *1 A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 O1 O2 O3 VSS 65 66 67 68 69 70 71 72 73 74 75 76 77 78 92 91 90 89 88 87 86 85 84 83 82 81 80 79 VCC A14 A13 A8 A9 A11 OE A10 CE O8 O7 O6 O5 O4 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 VCC P35/PWC P34/PTO2 P33/SI1 (UI1) P32/SO1 (UO1) P31/SCK1 (UCK1) /LMCO P30/PPG03/MCO C/NC *4 P00 P01 P02 P03 P04 P05 P06 P07 P10 P11 P12 P13 P14 P15 P16 P17 P20/PWCK P21/PPG01 P22/PPG02 P23 P24 P25 P26 P27 (DIP-64P-M01) (MDP-64C-P02) *1 : Package top pin assignments (MB89PV530 only) Pin no. Pin name Pin no. Pin name Pin no. Pin name Pin no. Pin name 65 A15 73 A1 81 O6 89 A8 66 A12 74 A0 82 O7 90 A13 67 A7 75 O1 83 O8 91 A14 68 A6 76 O2 84 CE 92 VCC 69 A5 77 O3 85 A10 70 A4 78 VSS 86 OE 71 A3 79 O4 87 A11 72 A2 80 O5 88 A9 N.C. : Internal connection only. Not for use. *2 : Pin 10 is P47/INT27/ADST pins except for MB89F538L and MOD2 pin for MB89F538L. *3 : Pin 25 and 26 are P63/INT13, P64 pins for single-clock and X0A, X1A pins for dual-clock. *4 : The function of pin 57 depends on the model. For details, see “■PIN DESCRIPTIONS” and “■HANDLING DEVICES”. (Continued) 8 MB89530 Series 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 P45/INT25/UO2 P44/INT24/UCK2 P43/INT23/SI2/SCL P42/INT22/SO2/SDA P41/INT21/SCK2 P40/INT20/EC P37/PTO1 P36/WTO VCC P35/PWC P34/PTO2 P33/SI1 (UI1) P32/SO1 (UO1) P31/SCK1 (UCK1) /LMCO P30/PPG03/MCO C/NC*3 (TOP VIEW) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 P00 P01 P02 P03 P04 P05 P06 P07 P10 P11 P12 P13 P14 P15 P16 P17 P63/INT13/X0A*2 P64/X1A*2 RST MOD0 MOD1 X0 X1 VSS P27 P26 P25 P24 P23 P22/PPG02 P21/PPG01 P20/PWCK 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 P46/INT26/UI2 P47/INT27/ADST/MOD2*1 P50/AN0 P51/AN1 P52/AN2 P53/AN3 P54/AN4 P55/AN5 P56/AN6 P57/AN7 AVCC AVR AVSS P60/INT10 P61/INT11 P62/INT12 (FPT-64P-M03) (FPT-64P-M09) *1 : Pin 2 is P47/INT27/ADST pins except for MB89F538L and MOD2 pin for MB89F538L. *2 : Pin 17 and 18 are P63/INT13, P64 pins for single-clock and X0A, X1A pins for dual-clock. *3 : The function of pin 49 depends on the model. For details, see “■PIN DESCRIPTIONS” and “■HANDLING DEVICES”. (Continued) 9 MB89530 Series 64 63 62 61 60 59 58 57 56 55 54 53 52 P44/INT24/UCK2 P43/INT23/SI2/SCL P42/INT22/SO2/SDA P41/INT21/SCK2 P40/INT20/EC P37/PTO1 P36/WTO VCC P35/PWC P34/PTO2 P33/SI1 (U1) P32/SO1/ (UO1) P31/SCK1 (UCK1) /LMCO (TOP VIEW) 84 83 82 81 80 79 78 *1 85 86 87 88 89 90 91 92 93 77 76 75 74 73 72 71 70 69 94 95 96 65 66 67 68 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 P30/PPG03/MCO C/NC*4 P00 P01 P02 P03 P04 P05 P06 P07 P10 P11 P12 P13 P14 P15 P16 P17 P20/PWCK RST MOD0 MOD1 X0 X1 VSS P27 P26 P25 P24 P23 P22/PPG02 P21/PPG01 20 21 22 23 24 25 26 27 28 29 30 31 32 P45/INT25/UO2 P46/INT26/UI2 P47/INT27/ADST/MOD2*2 P50/AN0 P51/AN1 P52/AN2 P53/AN3 P54/AN4 P55/AN5 P56/AN6 P57/AN7 AVCC AVR AVSS P60/INT10 P61/INT11 P62/INT12 P63/INT13/X0A*3 P64/X1A*3 (FPT-64P-M06) (MQP-64C-P01) *1 : Package top pin assignments (MB89PV530 only) Pin no. Pin name Pin no. Pin name 65 N.C. 73 A2 66 A15 74 A1 67 A12 75 A0 68 A7 76 N.C. 69 A6 77 O1 70 A5 78 O2 71 A4 79 O3 72 A3 80 VSS Pin no. 81 82 83 84 85 86 87 88 Pin name N.C. O4 O5 O6 O7 O8 CE A10 Pin no. 89 90 91 92 93 94 95 96 Pin name OE N.C. A11 A9 A8 A13 A14 VCC N.C. : Internal connection only. Not for use. *2 : Pin 3 is P47/INT27/ADST pins except for MB89F538L and MOD2 pin for MB89F538L. *3 : Pin 18 and 19 are P63/INT13, P64 pins for single-clock and X0A, X1A pins for dual-clock. *4 : The function of pin 50 depends on the model. For details, see “■PIN DESCRIPTIONS” and “■HANDLING DEVICES”. (Continued) 10 MB89530 Series (Continued) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 P00 P01 P02 P03 P04 P05 P06 P07 P10 P11 P12 P13 P14 P15 P16 P17 P63/INT13/X0A∗2 P64/X1A∗2 RST MOD0 MOD1 X0 X1 VSS P27 P26 P25 P24 P23 P22/PPG02 P21/PPG01 P20/PWCK 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 P46/INT26/UI2 P47/INT27/ADST/MOD2∗1 P50/AN0 P51/AN1 P52/AN2 P53/AN3 P54/AN4 P55/AN5 P56/AN6 P57/AN7 AVCC AVR AVSS P60/INT10 P61/INT11 P62/INT12 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 P45/INT25/UO2 P44/INT24/UCK2 P43/INT23/SI2/SCL P42/INT22/SO2/SDA P41/INT21/SCK2 P40/INT20/EC P37/PTO1 P36/WTO VCC P35/PWC P34/PTO2 P33/SI1 (UI1) P32/SO1 (UO1) P31/SCK1 (UCK1) /LMCO P30/PPG03/MCO C/NC∗3 (TOP VIEW) (LCC-64P-M19) (LCC-64P-M16) *4 *1 : Pin 2 is P47/INT27/ADST pins except for MB89F538L and MOD2 pin for MB89F538L. *2 : Pin 17 and 18 are P63/INT13, P64 pins for single-clock and X0A, X1A pins for dual-clock. *3 : The function of pin 49 depends on the model. For details, see “■PIN DESCRIPTIONS” and “■HANDLING DEVICES”. *4 : Only for ES 11 MB89530 Series ■ PIN DESCRIPTIONS Pin no. SH-DIP*1 MDIP*2 QFP*3 MQFP*4 LQFP*5 BCC*6 Pin name 30 23 22 X0 31 24 23 X1 28 21 20 MOD0 29 22 21 MOD1 I/O circuit type Function A Connecting pins to crystal oscillator circuit or other oscillator circuit. The X0 pin can connect to an external clock. In that case, X1 is left open. B Input pins for memory access mode setting. Connect directly to Vss. 27 20 19 RST C Reset I/O pin. This pin has pull-up resistance with CMOS I/O or hysteresis input. At an internal reset request, an ’L’ signal is output. An ’L’ level input initializes the internal circuits. 56 to 49 49 to 42 48 to 41 P00 to P07 D General purpose I/O ports. 48 to 41 41 to 34 40 to 33 P10 to P17 D General purpose I/O ports. 40 33 32 P20/PWCK E General purpose I/O port.Resource I/O pin (hysteresis input).Hysteresis input. This pin also functions as a PWC input. 39 32 31 P21/ PPG01 D General purpose I/O port.This pin also functions as the PPG01 output. 38 31 30 P22/ PPG02 D General purpose I/O port.This pin also functions as the PPG02 output. 37 30 29 P23 D General purpose I/O port. 36 29 28 P24 D General purpose I/O port. 35 28 27 P25 D General purpose I/O port. 34 27 26 P26 D General purpose I/O port. 33 26 25 P27 D General purpose I/O port. 58 51 50 P30/ PPG03/ MCO D General purpose I/O port.This pin also functions as the PPG03 output. 59 52 51 P31/SCK1 (UCK1) / LMCO E General purpose I/O port.Resource I/O pin (hysteresis input).This pin also functions as the UART/SIO clock input/output pin. 60 53 52 P32/SO1 (UO1) D General purpose I/O port.This pin also functions as the UART/SIO clock input/output pin. 61 54 53 P33/SI1 (UI1) E General purpose I/O port.Resource input/output pin (hysteresis input).This pin also functions as the UART/ SIO serial data input pin. 62 55 54 P34/PTO2 D General purpose I/O port.This pin also functions as the PWM time 2 output pin. 63 56 55 P35/PWC E General purpose I/O port.Resource I/O pin (hysteresis input).This pin also functions as a PWC input. (Continued) 12 MB89530 Series Pin no. QFP*3 MQFP*4 LQFP*5 BCC*6 Pin name I/O circuit type Function 1 58 57 P36/WTO D General purpose I/O port.Resource output.This pin also functions as the PWC output pin. 2 59 58 P37/PTO1 D General purpose I/O port.Resource output.This pin also functions as the PWM timer 1 output pin. 3 60 59 P40/INT20/ EC E General purpose I/O port.Resource I/O pin (hysteresis input)This pin also functions as an external interrupt input or 16-bit timer/counter input. 4 61 60 P41/INT21/ SCK2 E General purpose I/O port.Resource I/O pin (hysteresis input)This pin also functions as an external interrupt input or SIO clock I/O pin. 61 P42/INT22/ SO2/SDA G N-ch open drain output. Resource I/O pin (hysteresis only for INT22 input) . This pin also functions as an external interrupt input, SIO serial data output, or I2C data line. 62 P43/INT23/ SI2/SCL G N-ch open drain output. Resource I/O pin (hysteresis only for INT23 input) . This pin also functions as an external interrupt, SIO serial data input, or I2C clock I/O pin. 63 P44/INT24/ UCK2 E General purpose I/O port. Resource I/O pin (hysteresis input) . This pin also functions as an external interrupt input or UART clock I/O pin. 64 P45/INT25/ UO2 E General purpose I/O port. Resource I/O pin (hysteresis input) . This pin also functions as an external interrupt input or UART data output pin. 1 P46/INT26/ UI2 E General purpose I/O port. Resource I/O pin (hysteresis input) . This pin also functions as an external interrupt input or UART data input pin. P47/INT27/ ADST E except for MB89F 538L MOD2 B MB89F Input pin for memory access mode setting. 538L Connect to VSS directly. SH-DIP* MDIP*2 1 5 6 7 8 9 10 62 63 64 1 2 3 2 General purpose I/O port. Resource I/O pin (hysteresis input) . This pin also functions as an external interrupt input or A/D converter clock input pin. 11 to 18 4 to 11 3 to 10 P50/AN0 to P57/AN7 H N-ch open drain output port. This pin also functions as an A/D converter analog input pin. 22 to 24 15 to 17 14 to 16 P60/INT10 to P62/INT12 I General purpose input port. Resource input pin (hysteresis input) . This pin also functions as an external interrupt input pin. (Continued) 13 MB89530 Series (Continued) Pin no. SH-DIP* MDIP*2 25 1 QFP*3 MQFP*4 18 17 Pin name I/O circuit type Function P63/INT13 I Single-clock General purpose input port. Resource input pin (hysteresis input) . This pin also functions as an external interrupt. X0A A Dual-clock Connected pin for sub clock. P64 J Single-clock General purpose input port. X1A A Dual-clock Connected pin for sub clock. 26 19 18 64 57 56 VCC Power supply pin. 32 25 24 VSS Ground pin (GND) . 19 12 11 AVCC A/D converter power supply pin. 20 13 12 AVR A/D converter reference voltage input pin. 21 14 13 AVSS A/D converter power supply pin. Used at the same voltage level as the Vss supply. 57 50 *1 : DIP-64P-M01 *2 : MDP-64C-P02 *3 : FPT-64P-M06 *4 : MQP-64C-P01 *5 : FPT-64P-M03/M09 *6 : LCC-64P-M19/M16 14 LQFP*5 BCC*6 49 C MB89P538 Fixed at Vss. MB89PV530 MB89F538L MB89537/537C MB89538/538C N.C. pin MB89530 Series External EPROM Socket Pin Function Descriptions (MB89PV530 only) Pin no. I/O Circuit Pin name type 1 2 MQFP* MDIP* Function 65 66 67 68 69 70 71 72 73 74 66 67 68 69 70 71 72 73 74 75 A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 O Address output pins. 75 76 77 77 78 79 O1 O2 O3 I Data input pins. 78 80 VSS O Power supply pin (GND) . 79 80 81 82 83 82 83 84 85 86 O4 O5 O6 O7 O8 I Data input pins. 84 87 CE O ROM chip enable pin. Outputs an “H” level signal in standby mode. 85 88 A10 O Address output pin. 86 89 OE O ROM output enable pin. Outputs “L” at all times. 87 88 89 91 92 93 A11 A9 A8 O 90 94 A13 O 91 95 A14 O 92 96 VCC O EPROM power supply pin. 65 76 81 90 N.C. O Internally connected. These pins always left open. Address output pins. *1 : MDP-64C-P02 *2 : MQP-64C-P01 15 MB89530 Series ■ I/O CIRCUIT TYPES Type Circuit Remarks Oscillator feedback resistance • High speed side = approx. 1 MΩ • Low speed side = approx. 10 MΩ X1 (X1A) Nch A Pch Pch X0 (X0A) Nch • Hysteresis input • Pull-down resistance built-in to MB89537/537C MB89538/538C B • Pull-up resistance approx. 50 kΩ • Hysteresis input R Pch C Nch R Pull-up control resistor Pch • CMOS I/O • Software pull-up resistance can be used. Approx. 50 kΩ Pch D Nch R Pull-up control resistors Pch • CMOS I/O • Software pull-up resistance can be used. Approx. 50 kΩ Pch E Nch Port input Resource input (Continued) 16 MB89530 Series (Continued) Type Circuit Remarks • N-ch open drain output • Hysteresis input • CMOS input Nch G Resource input Port input • N-ch open drain output • Analog input (A/D converter) Pch H Nch Analog input R Pch Pull-up control resistors I • Hysteresis input • CMOS input • Software pull-up resistance can be used. Approx. 50 kΩ Resource Port R Pch Pull-up control resistors • CMOS input • Software pull-up resistance can be used. Approx. 50 kΩ J Port 17 MB89530 Series ■ HANDLING DEVICES 1. Preventing Latchup Care must be taken to ensure that maximum voltage ratings are not exceeded (to prevent latchup) . When CMOS integrated circuit devices are subjected to applied voltages higher than Vcc at input and output pins (other than medium- and high-withstand voltage pins), or to voltages lower than Vss, as well as when voltages in excess of rated levels are applied between Vcc and Vss, the phenomenon known as latchup can occur. When a latchup condition occurs, supply current can increase dramatically and may destroy semiconductor elements. In using semiconductor devices, always take sufficient care to avoid exceeding maximum ratings. Also when switching power on or off to analog systems, care must be taken that analog power supplies (AVCC, AVR) and analog input signals do not exceed the level of the digital power supply. 2. Power Supply Voltage Fluctuations Keep supply voltage levels as stable as possible. Even within the warranted operating range of the Vcc supply voltage, sudden changes in supply voltage can cause abnormal operation. As a measure for stability, it is recommended that the Vcc ripple fluctuation (peak to peak value) should be kept within 10% of the reference Vcc value on commercial power supply (50 Hz-60 Hz), and instantaneous voltage fluctuations such as at power-on and shutdown should be kept within a transient variability limit of 0.1V/ms. 3. Treatment of Unused Input Pins If unused input pins are left open, abnormal operation may result. Any unused input pins should be connected to pull-up or pull-down resistance. 4. Treatment of N.C. Pins Any pins marked ’NC’ (not connected) must be left open. 5. Treatment of Power Supply Pins on Models with Built-in A/D Converter Even when A/D converters are not in use, pins should be connected so that AVCC = VCC, and AVSS = AVR = VSS. 6. Precautions for Use of External Clock Even when an external clock signal is used, an oscillator stabilization wait period is used after power-on reset, or escape from sub clock mode or stop mode. 7. Execution of Programs on RAM Debugging of programs executed on RAM cannot be performed even when using the MB89PV530. 8. Wild Register Functions Wild registers cannot be debugged with the MB89PV530 and tools. To verify operations, actual in-device testing on the MB89P538 or MB89F538L is advised. 18 MB89530 Series 9. Details on Handling C Terminal of MB89530 Series The MB89530 series contains the following products. The regulator integrated model and the regulator-less model have different performance characteristics. Part No. Operation Voltage integrated model Terminal type Terminal treatments MB89PV530 MB89P538 MB89537/537C MB89538/538C MB89F538L Not included 2.7 V to 5.5 V 2.2 V to 3.6 V N.C terminal Included Not included C terminal N.C terminal Not required Fixed to VCC Fixed to VSS Not required 2.3 V to 3.6 V Although these product models have the same internal resources, the operation sequence after a power-on reset is different between the regulator integrated model and regulator-less model. The operation sequence after a power-on reset of each model is shown below. Power supply (VCC) Voltage step-down circuit stabilization time + oscillation stabilization time (219/Fch) CPU operation of regulator integrated model Oscillation stabilization time (218/Fch) CPU operation of regurator-less model CPU started on regulator-less model (Reset vector) CPU started on regulator integrated model (Reset vector) Fch : Crystal oscillator frequency As above, the regulator integrated model starts the CPU behind the regulator-less model. This is because the regulator requires a settling time for normal operation. The MB89P538 offers a choice of regulator-integrated and regulator-less models selectable depending on the C-terminal treatment. Use the right one for your mask board. 10. Note to Noise In the External Reset Pin (RST) If the reset pulse applied to the external reset pin (RST) does not meet the specifications, it may cause malfunctions. Use caution so that the reset pulse less than the specifications will not be fed to the external reset pin (RST) . 19 MB89530 Series ■ PROGRAMMING AND ERASING FLASH MEMORY ON THE MB89F538L 1. Flash Memory The flash memory is located between 4000H and FFFFH in the CPU memory map and incorporates a flash memory interface circuit that allows read access and program access from the CPU to be performed in the same way as mask ROM. Programming and erasing flash memory is also performed via the flash memory interface circuit by executing instructions in the CPU. This enables the flash memory to be updated in place under the control of the CPU, providing an efficient method of updating program and data. 2. Flash Memory Features • • • • • • • • 48 K byte×8-bit configuration : (16 K+8 K+8 K+16 K sectors) Automatic programming algorithm (Embedded algorithm* : Equivalent to MBM29LV200) Includes an erase pause and restart function Data polling and toggle bit for detection of program/erase completion Detection of program/erase completion via CPU interrupt Compatible with JEDEC-standard commands Sector Erasing (sectors can be combined in any combination) No. of program/erase cycles : 10,000 (Min) * : Embedded Algorithm is a trademark of Advanced Micro Devices. 3. Procedure for Programming and Erasing Flash Memory Programming and reading flash memory cannot be performed at the same time. Accordingly, to program or erase flash memory, the program must first be copied from flash memory to RAM so that programming can be performed without program access from flash memory. 4. Flash Memory Register • Control status register (FMCS) Address 007AH 20 bit7 bit6 bit5 bit4 INTE RDYINT WE RDY R/W R/W R/W R bit3 bit2 ReReserved served R/W R/W bit1 bit0 Reserved R/W Initial value 000X00-0B MB89530 Series 5. Sector Configuration The table below shows the sector configuration of flash memory and lists the addresses of each sector for both during CPU access a flash memory programming. • Sector configuration of flash memory FLASH Memory CPU Address Programmer Address* 16 K bytes FFFFH to C000H 1FFFFH to 1C000H 8 K bytes BFFFH to A000H 1BFFFH to 1A000H 8 K bytes 9FFFH to 8000H 19FFFH to 18000H 16 K bytes 7FFFH to 4000H 17FFFH to 14000H * : The programmer address is the address to be used instead of the CPU address when programming data from a parallel flash memory programmer. Use the programmer address on programming or erasing using a generalpurpose parallel programmer. 6. ROM Programmer Adaptor and Recommended ROM Programmers Part number Package Adaptor Part No. Recommended Programmer Manufacturer and Model Sunhayato Corp. Ando Electric Co., Ltd. MB89F538L-101PF MB89F538L-201PF FPT-64P-M06 FLASH-64QF-32DP-8LF MB89F538L-101PFM MB89F538L-201PFM FPT-64P-M09 FLASH-64QF2-32DP-8LF2 MB89F538L-101P-SH MB89F538L-201P-SH DIP-64P-M01 FLASH-64SD-32DP-8LF MB89F538L-101PV4 MB89F538L-201PV4 LCC-64P-M19 FLASH-64BCC-32DP-8LF AF9708* AF9709* * : For the version of the programmer, contact the Flash Support Group, Inc. • Enquiries Sunhayato Corp. : TEL FAX E-mail Flash Support Group, Inc. : FAX E-mail : +81-3-3984-7791 : +81-3-3971-0535 : [email protected] : +81-53-428-8377 : [email protected] 21 MB89530 Series ■ ONE-TIME WRITING SPECIFICATIONS WITH PROM AND EPROM MICROCONTROLLERS The MB89P538 has a PROM mode with functions equivalent to the MBM27C1001, allowing writing with a general purpose ROM writer using a proprietary adapter. Note, however, that the use of electronic signature mode is not supported. • ROM writer adapters With some ROM writers, stability of writing performance is enhanced by placing an 0.1µF capacitor between the Vcc and Vss pins. The following table lists adapters for use with ROM writers. ROM Writer Adapters Part number Package Compatible adapter MB89P538-101PF MB89P538-201PF FPT-64P-M06 ROM-64QF-32DP-8LA2*1 MB89P538-101PFM MB89P538-201PFM FPT-64P-M09 ROM-64QF2-32DP-8LA MB89P538-101P-SH MB89P538-201P-SH DIP-64P-M01 ROM-64SD-32DP-8LA2*1 MB89P538-101P-PV MB89P538-201P-PV LCC-64P-M16*2 ROM-64BCC-32DP-8LA-FJ Inquiries should be addressed to Sunhayato Corp. : TEL : +81-3-3984-7791 FAX : +81-3-3971-0535 E-mail : [email protected] *1 : Version 3 or later should be used. *2 : Only for ES • Memory map for EPROM mode The following illustration shows a memory map for EPROM mode. There are no PROM options. Normal operating mode 0000H EPROM mode (corresponding addresses on EPROM writer) 0000H I/O 0080H RAM 0100H 0200H 0880H General purpose register Prohibited Prohibited 4000H 4000H Program (EPROM) ROM FFFFH FFFFH Prohibited 1FFFFH 22 MB89530 Series • Recommended screening conditions Before one-time writing of microcontroller programs to PROM, high temperature aging is recommended as a screening process for chips before they are mounted. The following diagram shows the flow of the screening process. Program, verify High temperature aging +150 °C, 48 h Read Mount • About writing yields The nature of chips before one-time writing of microcontroller programs to PROM prevents the use of all-bit writing tests. Therefore it is not possible to guarantee writing yields of 100% in some cases. 23 MB89530 Series ■ EPROM WRITING TO PIGGY-BACK/EVALUATION CHIPS This section describes methods of writing to EPROM on piggy-back/evaluation chips. • EPROM model MBM27C512-20TV • Writer adapter For writing to EPROM using a ROM writer, use one of the writer adapters shown below (manufactured by Sunhayato Corp.) . Package Adapter socket model LCC-32 (rectangular) ROM-32LC-28DP-YG Inquiries should be addressed to Sunhayato Corp. : TEL : +81-3-3984-7791 FAX : +81-3-3971-0535 E-mail : [email protected] • Memory Space Piggy-back/Evaluation Memory Map Normal operating mode 0000H (Corresponding address on ROM writer) 0000H I/O 0080H Prohibited RAM 0880H Prohibited 4000H 4000H PROM 48 KB FFFFH EPROM FFFFH • Writing to EPROM 1) Set up the EPROM writer for the MBM27C512. 2) Load program data to the ERPOM writer, in the area 4000H - FFFFH. 3) Use the EPROM writer to write to the area 4000H - FFFFH. 24 MB89530 Series Low voltage oscillator circuit (32.786 kHz) P64/X1A*2 CMOS I/O port Port 0 Sub clock P63/INT13/X0A*2 8 Port 1 ■ BLOCK DIAGRAM 8 P00 ∼ P07 Clock control P60/INT10 ∼ P62/INT12 Port 6 Watch prescaler CMOS I/O port 4 External interrupt 1 (edge) CMOS I/O port Main clock 6-bit PPF03 P31/SCK1 (UCK1) /LMCO 8-bit PWM timer 2 P34/PTO2 8-bit PWM timer 1 UART/SIO P35/PWC P23 ∼ P27 CMOS I/O port P40/INT20/EC SIO P41/INT21/SCK2 UART I2C P42/INT22/ SO2/SDA P43/INT23/ SI2/SCL 16-bit timer/ counter 1 P44/INT24/UCK2 External interrupt 2 (level) P45/INT25/UO2 P46/INT26/UI2 P47/INT27/ADST*1 CMOS I/O port PWC P36/WTO P37/PTO1 P22/PPG02 N-ch output CMOS I/O port 1KB RAM/2KB RAM 8 10-bit A/D converter F2MC-8L CPU Port 5 P33/SI1 (UI1) Port 3 P30/PPG03/MCO P21/PPG01 N-ch I/O 21-bit time base timer P20/PWCK Port 4 (watchdog timer) Internal databus Reset circuit RST P32/SO1 (UO1) 12-bit PPG02 Oscillator circuit Clock controller Port 2 12-bit PPG01 X0 X1 P10 ∼ P17 8 P50/AN0 ∼ P57/AN7 AVCC AVR AVSS Wild register 32KB ROM/48KB ROM Other pins MOD0, MOD1, MOD2*1, C, VCC, VSS, C/NC *1 : P47/INT27/ADST pins except for MB89F538L, MOD2 pin for MB89F538L *2 : P63/INT13, P64 pins for single-clock, X0A, X1A pins for dual-clock 25 MB89530 Series ■ CPU CORE 1. Memory Space The MBM89530 series has 64 KB of memory space, containing all I/O, data areas, and program areas. The I/ O area is located at the lowest addresses, with the data area placed immediately above. The data area can be partitioned into register areas, stack areas, or direct access areas depending on the application. The program area is located at the opposite end of memory, closest to the highest addresses, and the highest part of this area is assigned to the tables of interrupt and reset vectors and vector call instructions. The following diagram shows the structure of memory space in the MB89530 series. • Memory Map MB89PV530 MB89P538/F538L MB89538/538C MB89537/537C 0000H 0000H I/O 0080H I/O 0080H RAM 0100H 0200H RAM 0100H General purpose register 0200H General purpose register 0480H Open 0C80H 0C91H 0880H Open 0C80H Wild register 0C91H Wild register Open Open 4000H 8000H ROM External ROM*1 ROM FFC0H FFC0H Vector tables*2 FFFFH *1 : The external ROM area is on the MBM89PV530 only. *2 : Vector tables (reset, interrupt, vector call instructions) 26 FFFFH Vector tables*2 MB89530 Series 2. Registers The F2MC-8L series has two types of registers, dedicated-use registers within the CPU, and general-purpose registers in memory. The dedicated-use registers are the following. Program counter (PC) : 16-bit length, shows the location where instructions are stored. Accumulator (A) : 16-bit length, a temporary memory register for calculation operations. The lower byte is used for 8-bit data processing instructions. Temporary accumulator (T) : 16-bit length, performs calculations with the accumulator. The lower byte is used for 8-bit data processing instructions. Index register (IX) : 16-bit length, a register for index modification. Extra pointer (EP) : 16-bit length, a pointer indicating memory addresses. Stack pointer (SP) : 16-bit length, indicates stack areas. Program status (PS) : 16-bit length, contains register pointer and condition code. 16 bits Initial value FFFDH : Program counter PC A : Accumulator Not fixed T : Temporary accumulator Not fixed IX : Index register Not fixed EP : Extra pointer Not fixed SP : Stack pointer Not fixed PS : Program status I-flag = 0, IL1, 0 = 11 Other bits not fixed In addition, the PS register can be divided so that the upper 8 bits are used as a register bank pointer (RP), and the lower 8 bits as a condition code register (CCR). (See the following illustration.) • Program status register configuration 15 PS 14 13 12 RP RP 11 7 6 5 4 3 2 1 0 Open Open Open H 10 9 8 I IL1 IL0 N Z V C CCR 27 MB89530 Series The RP register shows the address of the register bank currently being used, so that the RP value and the actual address are related by the conversion rule shown in the following illustration. • General purpose register area real address conversion principle Operation code lower RP upper "0" Address generated "0" "0" "0" "0" "0" A15 A14 A13 A12 A11 A10 "0" "1" R4 A9 A8 A7 R3 A6 R2 A5 R1 A4 R0 A3 b2 A2 b1 b0 A1 A0 The CCR register has bits that show the content of results of calculations and transferred data, and bits that control CPU operation during interrupts. H-flag I-flag IL1, 0 N-flag Z-flag V-flag C-flag : Set to 1 if calculations result in carry or borrow operations from bit 3 to bit 4, otherwise set to 0. This flag is used for decimal correction instructions. : This flag is set to 1 if interrupts are enabled, and 0 if interrupts are prohibited. The default value at reset is 0. : Indicates the level of the currently permitted interrupts. Only interrupt requests having a more powerful level than the value of these bits will be processed. : : : : IL1 IL0 Interrupt level 0 0 0 1 1 0 2 1 1 3 1 Strength Strong Weak Set to 1 if the highest bit is 1 after a calculation, otherwise cleared to 0. Set to 1 if a calculation result is 0, otherwise cleared to 0. Set to 1 if a two’s complement overflow results during a calculation, otherwise cleared to 0. Set to 1 if a calculation results in a carry or borrow operation from bit 7, otherwise cleared to 0. This is also the shift-out value in a shift instruction. In addition, the following general purpose registers are available. General purpose registers: 8-bit length, used to contain data. The general purpose registers are 8-bit registers located in memory. There are eight such registers per bank, and the MB89530 series have up to 32 banks for use. The bank currently in use is indicated by the register bank pointer (RP). 28 MB89530 Series •Register bank configuration Address at this location = 0100H + 8 × (RP) R0 R1 R2 R3 R4 R5 R6 R7 32 banks Memory area 29 MB89530 Series ■ I/O MAP Address Register name 00H PDR0 Port 0 data register 01H DDR0 Port 0 direction register 02H PDR1 Port 1 data register 03H DDR1 Port 1 direction register Register description 04H to 06H Write/Read Initial value R/W XXXXXXXXB W 0 0 0 0 0 0 0 0B R/W XXXXXXXXB W 0 0 0 0 0 0 0 0B (Reserved area) 07H SYCC System clock control register R/W X -1 MM1 0 0B 08H STBC Standby control register R/W 0 0 0 1 0 - - -B 09H WDTC Watchdog control register R/W 0 - - - XXXXB 0AH TBTC Time base timer control register R/W 0 0 - - - 0 0 0B 0BH WPCR Watch prescaler control register R/W 0 0 - - 0 0 0 0B 0CH PDR2 Port 2 data register R/W XXXXXXXXB 0DH DDR2 Port 2 direction register R/W 0 0 0 0 0 0 0 0B 0EH PDR3 Port 3 data register R/W XXXXXXXXB 0FH DDR3 Port 3 direction register R/W 0 0 0 0 0 0 0 0B 10H PDR4 Port 4 data register R/W XXXX 1 1 XXB 11H DDR4 Port 4 direction register R/W 0 0 0 0 - - 0 0B 12H PDR5 Port 5 data register R/W 11111111B 13H PDR6 Port 6 data register R XXXXXXXXB 14H to 21H (Reserved area) 22H SMC11 Serial mode control register 1 (UART) R/W 0 0 0 0 0 0 0 0B 23H SRC1 Serial route control register (UART) R/W - - 0 1 1 0 0 0B 24H SSD1 Serial status and data register (UART) R/W 0 0 1 0 0 - 1XB 25H SIDR1/ SODR1 Serial input/output data register (UART) R/W XXXXXXXXB 26H SMC12 Serial mode control register 2 (UART) R/W - - 1 0 0 0 0 1B 27H CNTR1 PWM control register 1 R/W 0 0 0 0 0 0 0 0B 28H CNTR2 PWM control register 2 R/W 0 0 0 - 0 0 0 0B 29H CNTR3 PWM control register 3 R/W - 0 0 0 - - - -B 2AH COMR1 PWM compare register 1 W XXXXXXXXB 2BH COMR2 PWM compare register 2 W XXXXXXXXB 2CH PCR1 PWC pulse width control register 1 R/W 0 0 0 - - 0 0 0B 2DH PCR2 PWC pulse width control register 2 R/W 0 0 0 0 0 0 0 0B 2EH RLBR PWC reload buffer register R/W XXXXXXXXB 2FH SMC21 Serial mode control register 1 (UART/SIO) R/W 0 0 0 0 0 0 0 0B 30H SMC22 Serial mode control register 2 (UART/SIO) R/W 0 0 0 0 0 0 0 0B 31H SSD2 Serial status and data register (UART/SIO) R/W 0 0 0 0 1 - - -B 32H SIDR2/ SODR2 Serial data register (UART/SIO) R/W XXXXXXXXB (Continued) 30 MB89530 Series Address Register name 33H SRC2 34H Register description Write/Read Initial value Baud rate generator reload register R/W XXXXXXXXB ADC1 A/D control register 1 R/W 0 0 0 0 0 0 - 0B 35H ADC2 A/D control register 2 R/W - 0 0 0 0 0 0 1B 36H ADDL A/D data register low R/W XXXXXXXXB 37H ADDH A/D data register high R/W - - - - - - 0 0B 38H PPGC2 PPG2 control register (12-bit PPG) R/W 0 0 0 0 0 0 0 0B 39H PRL22 PPG2 reload register 2 (12-bit PPG) R/W 0X0 0 0 0 0 0B 3AH PRL21 PPG2 reload register 1 (12-bit PPG) R/W XX0 0 0 0 0 0B 3BH PRL23 PPG2 reload register 3 (12-bit PPG) R/W XX0 0 0 0 0 0B 3CH TMCR 16-bit timer control register R/W - - 0 0 0 0 0 0B 3DH TCHR 16-bit timer counter register high R/W 0 0 0 0 0 0 0 0B 3EH TCLR 16-bit timer counter register low R/W 0 0 0 0 0 0 0 0B 3FH EIC1 External interrupt 1 control register 1 R/W 0 0 0 0 0 0 0 0B 40H EIC2 External interrupt 1 control register 2 R/W 0 0 0 0 0 0 0 0B R/W - - - - - - - 0B R/W 0 0 0 0 0 0 0 0B 41H to 48H 49H (Reserved area) DDCR DDC select register 4AH to 4BH (Reserved area) 4CH PPGC1 4DH PRL12 PPG1 reload register 2 (12-bit PPG) R/W 0X0 0 0 0 0 0B 4EH PRL11 PPG1 reload register 1 (12-bit PPG) R/W XX0 0 0 0 0 0B 4FH PRL13 PPG1 reload register 3 (12-bit PPG) R/W XX0 0 0 0 0 0B R/W - - - - - 0 0 0B 50H IACR PPG1 control register (12-bit PPG) 2 I C address control register 2 51H IBSR I C bus status register R 0 0 0 0 0 0 0 0B 52H IBCR I2C bus control register R/W 0 0 0 0 0 0 0 0B 2 R/W 0 0 0 XXXXXB 2 R/W - XXXXXXXB 2 53H 54H ICCR IADR I C clock control register I C address register 55H IDAR I C data register R/W XXXXXXXXB 56H EIE2 External interrupt 2 control register R/W 0 0 0 0 0 0 0 0B 57H EIF2 External interrupt 2 flag register R/W - - - - - - - 0B 58H RCR1 6-bit PPG control register 1 R/W 0 0 0 0 0 0 0 0B 59H RCR2 6-bit PPG control register 2 R/W 0X0 0 0 0 0 0B 5AH CKR Clock output control register R/W - - - - - - 0 0B R/W 0 0 0 0 0 0 0 0B 5BH to 6FH 70H (Reserved area) SMR Serial mode register (SIO) 71H SDR Serial data register (SIO) R/W XXXXXXXXB 72H PURR0 Port 0 pull-up resistance register R/W 11111111B 73H PURR1 Port 1 pull-up resistance register R/W 11111111B 74H PURR2 Port 2 pull-up resistance register R/W 11111111B 75H PURR3 Port 3 pull-up resistance register R/W 11111111B (Continued) 31 MB89530 Series (Continued) Address Register name 76H PURR4 77H Register description Write/Read Initial value Port 4 pull-up resistance register R/W 1 1 1 1 - -1 1 B WREN Wild register enable register R/W - - 0 0 0 0 0 0B 78H WROR Wild register data test register R/W - - 0 0 0 0 0 0B 79H PURR6 Port 6 pull-up resistance register R/W ---11111B 7AH FMCS FLASH control status register R/W 000X00 - 0 B 7BH ILR1 Interrupt level setting register 1 W 1 1 1 1 1 1 1 1B 7CH ILR2 Interrupt level setting register 2 W 1 1 1 1 1 1 1 1B 7DH ILR3 Interrupt level setting register 3 W 1 1 1 1 1 1 1 1B 7EH ILR4 Interrupt level setting register 4 W 1 1 1 1 1 1 1 1B 7FH ITR Interrupt test register C80H WRARH1 Upper address setting register 1 R/W XXXXXXXX C81H WRARL1 Lower address setting register 1 R/W XXXXXXXX C82H WRDR1 Data setting register 1 R/W XXXXXXXX C83H WRARH2 Upper address setting register 2 R/W XXXXXXXX C84H WRARL2 Lower address setting register 2 R/W XXXXXXXX C85H WRDR2 Data setting register 2 R/W XXXXXXXX C86H WRARH3 Upper address setting register 3 R/W XXXXXXXX C87H WRARL3 Lower address setting register 3 R/W XXXXXXXX C88H WRDR3 Data setting register 3 R/W XXXXXXXX C89H WRARH4 Upper address setting register 4 R/W XXXXXXXX C8AH WRARL4 Lower address setting register 4 R/W XXXXXXXX C8BH WRDR4 Data setting register 4 R/W XXXXXXXX C8CH WRARH5 Upper address setting register 5 R/W XXXXXXXX C8DH WRARL5 Lower address setting register 5 R/W XXXXXXXX C8EH WRDR5 Data setting register 5 R/W XXXXXXXX C8FH WRARH6 Upper address setting register 6 R/W XXXXXXXX C90H WRARL6 Lower address setting register 6 R/W XXXXXXXX C91H WRDR6 Data setting register 6 R/W XXXXXXXX • Description of write/read symbols : R/W : read/write enabled R : Read only W : Write only • Description of initial values : 0 : This bit initialized to “0”. 1 : This bit initialized to “1”. X : The initial value of this bit is not determined. M : The initial value of this bit is a mask option. - : This bit is not used. Note : Do not use reserved spaces. 32 Access prohibited XXXXXX0 0B MB89530 Series ■ ELECTRICAL CHARACTERISTICS 1. Absolute Maximum Ratings Parameter Symbol (AVss = Vss = 0 V) Rating Unit Remarks Min Max VCC AVCC VSS − 0.3 VSS + 4.0 V AVR VSS − 0.3 VSS + 4.0 V VCC AVCC VSS − 0.3 VSS + 6.0 V AVR VSS − 0.3 VSS + 6.0 V VSS − 0.3 VCC + 0.3 V Other than P42, P43 VSS − 0.3 VSS + 6.0 V Only P42, P43 VSS − 0.3 VCC + 0.3 V Other than P42, P43 VSS − 0.3 VSS + 6.0 V Only P42, P43 − 2.0 + 2.0 mA *2 Total maximum clamp current ∑| ICLAMP | 20 mA *2 “L” level maximum output current IOL 15 mA “L” level average output current IOLAV 4 mA “L” level maximum total output current ΣIOL 100 mA ΣIOLAV 40 mA IOH −15 mA “H” level average output current IOHAV −4 mA “H” level maximum total output current ΣIOH −50 mA ΣIOHAV −20 mA Current consumption PD 300 mW Operating temperature TA −40 +85 °C Tstg −55 +150 °C Supply voltage Input voltage VI Output voltage VO Maximum clamp current “L” level average total output current “H” level maximum output current “H” level average total output current Storage temperature ICLAMP MB89537/538 MB89537C/538C MB89F538L MB89P538 MB89PV530 *1 *1 Average value (operating current × operating duty) Average value (operating current × operating duty) Average value (operating current × operating duty) Average value (operating current × operating duty) *1 : AVcc and Vcc are to be used at the same potential. AVR should not exceed AVcc + 0.3 V. *2 : • Applicable to pins : P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40, P41, P44 to P47, P50 to P57, P60 to P64 • Use within recommended operating conditions. • Use at DC voltage (current) . (Continued) 33 MB89530 Series (Continued) • The +B signal should always be applied with a limiting resistance placed between the +B signal and the microcontroller. • The value of the limiting resistance should be set so that when the +B signal is applied the input current to the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods. • Note that when the microcontroller drive current is low, such as in the power saving modes, the +B input potential may pass through the protective diode and increase the potential at the VCC pin, and this may affect other devices. • Note that if a +B signal is input when the microcontroller current is off (not fixed at 0 V) , the power supply is provided from the pins, so that incomplete operation may result. • Note that if the +B input is applied during power-on, the power supply is provided from the pins and the resulting supply voltage may not be sufficient to operate the power-on result. • Care must be taken not to leave the +B input pin open. • Note that analog system input/output pins other than the A/D input pins (LCD drive pins, comparator input pins, etc.) cannot accept +B signal input. • Sample recommended circuits : • Input/Output Equivalent circuits Protective diode VCC Limiting resistance P-ch +B input (0 V to 16 V) N-ch R WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings. 34 MB89530 Series 2. Recommended Operating Conditions Parameter Value Symbol VCC, AVCC Supply voltage Operating temperature (AVss = Vss = 0 V) Unit Remarks Min Max 2.2* 3.6 V Range warranted for normal operation 1.5 3.6 V RAM status in stop mode 2.4 3.6 V Range warranted for normal operation 1.5 3.6 V RAM status in stop mode 2.7* 5.5 V Range warranted for normal operation 1.5 5.5 V RAM status in stop mode AVR 2.4 AVCC V TA −40 +85 °C MB89537/538 MB89537C/ 538C MB89F538L MB89P538 MB89PV530 * : Varies according to frequency used, and instruction cycle. See “Operating voltage vs. operating frequency (MB89537/MB89538/MB89537C/MB89538C) and (MB89P538/ MB89PV530) ” and “5. A/D Converter Electrical Characteristics”. Operating voltage vs. operating frequency (MB89537/MB89538/MB89537C/MB89538C) Operating voltage VCC (V) Range of warranted analog precision : VCC = AVCC = 2.4 V to 3.6 V 4.0 3.6 3.0 2.4 2.2 2.0 1.0 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 12.5 Operating frequency (MHz) (at instruction cycle = 4 / Fc) 4.0 2.0 0.8 0.4 0.32 Minimum instruction execution time (Instruction cycles) (µs) 35 MB89530 Series Operating voltage vs. operating frequency (MB89F538L) Operating voltage VCC (V) Range of warranted analog precision : VCC = AVCC = 2.4 V to 3.6 V 4.0 3.6 3.0 2.4 2.0 1.0 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 12.5 Operating frequency (MHz) (at instruction cycle = 4 / Fc) 4.0 2.0 0.8 0.4 0.32 Minimum instruction execution time (Instruction cycles) (µs) 36 MB89530 Series Operating voltage vs. operating frequency (MB89P538/MB89PV530) Range of warranted analog precision : VCC = AVCC = 3.5 V to 5.5 V 5.5 Operating voltage VCC (V) 5.0 4.0 3.5 3.0 2.7 2.2 2.0 1.0 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 12.5 Operating frequency (MHz) (at instruction cycle = 4 / Fc) 4.0 2.0 0.8 0.4 0.32 Minimum instruction execution time (Instruction cycles) (µs) indicates warranted operation at TA = −10 °C to +55 °C WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device’s electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their FUJITSU representatives beforehand. 37 MB89530 Series 3. DC Characteristics Parameter “H” level input voltage (AVCC = VCC = 3.0 V, AVss = Vss = 0 V, TA = −40 °C to +85 °C) Symbol Pin name Condition VIH P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P60 to P64, SI1, SI2 VIHS RST, MOD0, MOD1, INT20 to INT27, UCK1, UI1, INT10 to INT13, SCK1, EC, PWCK, PWC, SCK2, UCK2, UI2, ADST Value Unit Typ Max 0.7 VCC VCC + 0.3 V 0.8 VCC VCC + 0.3 V VSS + 1.4 VSS + 5.5 V With SMB input buffer selected* 0.7 VCC VSS + 5.5 V With I2C input buffer selected* VIL P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P60 to P64, SI1, SI2 VSS − 0.3 0.3 VCC V VILS RST, MOD0, MOD1, INT20 to INT27, UCK1, UI1, INT10 to INT13, SCK1, EC, PWCK, PWC, SCK2, UCK2, UI2, ADST VSS − 0.3 0.2 VCC V VSS − 0.3 VSS + 0.6 V With SMB input buffer selected* VSS − 0.3 0.3 VCC V With I2C input buffer selected* VSS − 0.3 VCC + 0.3 V VSS + 5.5 V 2.4 V P00 to P07, P10 to P17, P20 to P27, P30 to P37, IOL = P40 to P47, P50 to P57, 4.0 mA RST 0.4 V P00 to P07, P10 to P17, P20 to P27, P30 to P37, 0.0 V < VI P40 to P47, P50 to P57, < VCC P60 to P64 −5 +5 µA VIHSMB SCL, SDA VIHI2C “L” level input voltage VILSMB SCL, SDA VILI2C Open drain output applied voltage “H” level output voltage VD1 P50 to P57 VD2 P42, P43 VOH P00 to P07, P10 to P17, IOH = P20 to P24, P30 to P37, −2.0 mA P40, P41, P44 to P47 P25 to P27 “L” level output voltage Input leak current (Hi-Z output leak current) Remarks Min VOL ILI IOH = −3.0 mA With no pull-up resistance specified (Continued) 38 MB89530 Series (Continued) Parameter Open drain output leak current Pull-up resistance Symbol Pin name (AVCC = VCC = 3.0 V, AVss = Vss = 0 V, TA = −40 °C to +85 °C) Value Condition Unit Remarks Min Typ Max 0.0 V < VI < VSS + 5.5 V ILIOD P42, P43 RPULL P00 to P07, P10 to P17, P20 to P27, VI = 0.0 V P30 to P37, P40, P41, P44 to P47, P60 to P64, RST ICCS1 ICCS2 ICCL VCC Supply current +5 µA With pull-up resistance is selected. kΩ The RST signal is excluded. 50 100 6 10 45 1.5 3 mA 2 4 mA Sleep mode 1 2 mA Sleep mode FCL = 32.768 kHz 1 3 mA FCL = 32.768 kHz TA = +25 °C 35 90 µA FCL = 32.768 kHz 20 50 µA FCL = 32.768 kHz 15 30 µA FCL = 32.768 kHz TA = +25 °C 15 30 µA FCL = 32.768 kHz 5 15 µA 5 15 µA 1 5 µA FCH = 10.0 MHz 1 3 mA TA = +25 °C 1 5 µA 5 15 pF FCH = 10.0 MHz tinst = 6.4 µs FCH = 10.0 MHz tinst = 0.4 µs FCH = 10.0 MHz tinst = 6.4 µs ICC2 25 FCH = 10.0 MHz tinst = 0.4 µs ICC1 mA Normal operation FLASH memory mA programming/erase MB89F538L ICCLS ICCT FCL = 32.768 kHz TA = +25 °C TA = +25 °C ICCH IA IAH Input capacitance CIN AVCC Except VCC, VSS, f = 1 MHz AVCC, AVSS Sub mode MB89P538/PV530 Sub mode MB89F538L Sub mode MB89537/538 MB89537C/538C Sub, sleep modes Except MB89F538L Watch mode, main stop MB89F538L Watch mode, main stop Except MB89F538L Sub, sleep modes MB89F538L Sub, stop modes A/D conversion running A/D stopped * : The MB89PV530/P538/F538L/537C/538C have a built-in I2C function, and a choice of input buffers by software setting. The MB89537/538 have no built-in I2C functions, and therefore this standard does not apply. 39 MB89530 Series 4. AC Characteristics (1) Reset Timing (VCC = 3.0 V, AVss = Vss = 0 V, TA = −40 °C to +85 °C) Parameter RST “L” pulse width Symbol Condition tZLZH Value Min Max 48 tHCYL Unit Remarks ns Notes : • tHCYL is the main clock oscillator period. • If the reset pulse applied to the external reset pin (RST) does not meet the specifications, it may cause malfunctions. Use caution so that the reset pulse less than the specifications will not be fed to the external reset pin (RST) . tZLZH RST 0.2 VCC 0.2 VCC (2) Power-on Reset (AVss = Vss = 0 V, TA = −40 °C to +85 °C) Parameter Power on time Power shutoff time Symbol Condition tR tOFF Value Unit Min Max 0.5 50 ms 1 ms Remarks For repeated operation Note : Be sure that the power supply will come on within the selected oscillator stabilization period. Also, when varying the supply voltage during operation, it is recommended that the supply voltage be increased gradually. tR tOFF 2.2 V VCC 0.2 V 40 0.2 V 0.2 V MB89530 Series (3) Clock Timing Standards Parameter (AVss = Vss = 0 V, TA = −40 °C to +85 °C) Symbol Pin name Condition Clock frequency Clock cycle time Input clock pulse width Input clock rise, fall time Value Min Typ Max Unit Remarks FCH X0, X1 1 12.5 FCL X0A, X1A 32.768 kHz Sub clock tHCYL X0, X1 80 1000 ns Main clock tLCYL X0A, X1A 30.5 µs Sub clock PWH PWL X0 20 ns External clock PWHH PWLL X0A 15.2 µs External clock tCR tCF X0 10 ns External clock MHz Main clock • X0, X1 timing and application conditions tHCYL PWH PWL tCR tCF 0.8 VCC 0.8 VCC X0 0.2 VCC 0.2 VCC 0.2 VCC • Clock application conditions Using a crystal oscillator or ceramic oscillator X0 X1 X0 FCH C1 Using an external clock signal C2 X1 Open FCH 41 MB89530 Series • X0A, X1A timing and application conditions tLCYL PWLH PWLL tCR tCF 0.8 VCC 0.8 VCC X0A 0.2 VCC 0.2 VCC 0.2 VCC • Clock application conditions Using a crystal oscillator or ceramic oscillator X0A Using an external clock signal X1A X0A Open FCL C1 FCL C2 (4) Instruction Cycle Parameter Instruction cycle (minimum instruction execution time) 42 X1A (AVss = Vss = 0 V, TA = −40 °C to +85 °C) Symbol Rated value Unit Remarks 4/FCH, 8/FCH, 16/FCH, 64/FCH µs Operating at FCH = 12.5 MHz (4/FCH) tinst = 0.32 µs 2/FCL µs Operating at FCL = 32.768 kHz tinst = 61.036 µs tinst MB89530 Series (5) Serial I/O Timing Parameter (VCC = 3.0 V, AVss = Vss = 0 V, TA = −40 °C to +85 °C) Symbol Pin name Condition Serial clock cycle time tSCYC SCK, UCK SCK↓→SO tSLOV SCK, SO, UCK, UO Valid SI→SCK↑ tIVSH SI, SCK, UI, UCK SCK↑→ valid SI hold time tSHIX SCK, SI, UCK, UI Serial clock “H” pulse width tSHSL ÉSerial clock “L” pulse width tSLSH SCK↓→SO time tSLOV SCK, SO, UCK, UO Valid SI→SCK↑ tIVSH SI, SCK, UI, UCK SCK↑→ valid SI hold time tSHIX SCK, SI, UCK, UI Internal clock operation SCK, UCK External clock operation Value Unit Remarks Min Max 2 tinst µs −200 +200 ns 200 ns 200 ns 1 tinst µs 1 tinst µs 0 200 ns 200 ns 200 ns Note : For tinst see “ (4) Instruction Cycle”. Internal shift clock mode tSCYC SCK UCK 2.4 V 0.8 V 0.8 V tSLOV SO UO 2.4 V 0.8 V tIVSH tSHIX 0.8 VCC 0.2 VCC SI UI 0.8 VCC 0.2 VCC External shift clock mode tSLSH tSHSL SCK UCK 0.8 VCC 0.2 VCC 0.8 VCC 0.2 VCC tSLOV SO UO 2.4 V 0.8 V tIVSH SI UI 0.8 VCC 0.2 VCC tSHIX 0.8 VCC 0.2 VCC 43 MB89530 Series (6) Peripheral Input Timing Parameter (VCC = 3.0 V, AVss = Vss = 0 V, TA = −40 °C to +85 °C) Symbol Pin name Peripheral input “H” level pulse width 1 tILIH1 Peripheral input “L” level pulse width 1 tIHIL1 INT10 to INT13, INT20 to INT27, EC, PWC, PWCK Peripheral input “H” level pulse width 2 tILIH2 Peripheral input “L” level pulse width 2 tIHIL2 Condition Value Max 2 tinst µs 2 tinst µs 28 tinst µs 28 tinst µs ADST Note : For tinst see “ (4) Instruction Cycle”. tIHIL1 EC, INT, PWC, PWCK tILIH1 0.8 VCC 0.2 VCC tILIH2 0.8 VCC 0.2 VCC 0.8 VCC 0.2 VCC tIHIL2 ADST 44 Unit Min 0.2 VCC 0.8 VCC Remarks MB89530 Series (7) I2C Timing Parameter (VCC = 3.0 V, AVss = Vss = 0 V, TA = −40 °C to +85 °C) Symbol Pin Condition name Value Min Max 1 / 4 tinst × m × n − 20 1 / 4 tinst × m × n + 20 Unit Remarks ns Master only Master only Start condition output tSTA SCL SDA Stop condition output tSTO SCL SDA 1 / 4 tinst × 1 / 4 tinst × (m × n + 8) − 20 (m × n + 8) + 20 ns Start condition detection tSTA SCL SDA 1 / 4 tinst × 6 + 40 ns Stop condition detection tSTO SCL SDA 1 / 4 tinst × 6 + 40 ns Restart condition output tSTASU SCL SDA 1 / 4 tinst × 1 / 4 tinst × (m × n + 8) − 20 (m × n + 8) + 20 ns Restart condition detection tSTASU SCL SDA 1 / 4 tinst × 4 + 40 ns SCL output “L” width tLOW SCL 1 / 4 tinst × m × n − 20 1 / 4 tinst × m × n + 20 ns Master only SCL output “H” width tHIGH SCL 1 / 4 tinst × 1 / 4 tinst × (m × n + 8) − 20 (m × n + 8) + 20 ns Master only SDA output delay time tDO SDA 1 / 4 tinst × 4 − 20 1 / 4 tinst × 4 + 20 ns Setup after SDA output interrupt interval tDOSU SDA 1 / 4 tinst × 4 − 20 ns SCL input “L” width tLOW SCL 1 / 4 tinst × 6 + 40 ns SCL input “H” width tHIGH SCL 1 / 4 tinst × 2 + 40 ns SDA input setup tSU SDA 40 ns SDA input hold tHO SDA 0 ns Master only Notes : • For tinst see “ (4) Instruction Cycle”. • The value “m” in the above table is the value from the shift clock frequency setting bits (CS4-CS3) in the clock control register “ICCR”. For details, refer to the register description in the hardware manual. • The value ’n’ in the above table is the value from the shift clock frequency setting bits (CS2-CS0) in the clock control register “ICCR”. For details, refer to the register description in the hardware manual. • tDOSU appears when the interrupt period is longer than the SCL “L” width. • The rated values for SDA and SCL assume a start up time of 0 ns. 45 MB89530 Series • I2C interface [Data sending (master/slave) ] tSU tDO tDO tSU tDOSU SDA ACK tSTASU tSTA tLOW SCL tHO 1 9 • I2C interface [Data sending (master/slave) ] tSU tHO tDO tDO tDOSU SDA ACK tHIGH tLOW tSTO SCL 6 46 7 8 9 MB89530 Series 5. A/D Converter Electrical Characteristics (1) MB89537/538/537C/538C Parameter Symbol Pin name (VCC = 2.4 V to 3.6 V, AVSS = VSS = 0 V, TA = −40 °C to +85 °C) Value Condition Unit Remarks Min Typ Max Resolution capability Total error Linear error Differential linear error Zero transition voltage VOT Full scale transition voltage VFST AVR = AVCC Inter-channel variation Conversion time Sampling time Analog input current IAIN Analog input voltage VAIN Reference voltage Reference voltage supply current IR 10 bit ±3.0 LSB ±2.5 LSB ±1.9 LSB AVSS − 1.5 AVSS + 0.5 AVSS + 2.5 LSB LSB LSB mV AVR − 3.5 AVR − 1.5 AVR + 1.5 LSB LSB LSB mV 4.0 LSB 60 tinst µs 16 tinst µs 10 µA AVSS AVR V AN0 to AN7 AVSS + 2.4 AVCC V AVR A/D running 200 µA A/D off 5 µA IRH AVCC = VCC * * : Includes sampling time (2) MB89F538L Parameter Symbol Pin name Resolution capability Total error Linear error (VCC = 2.4 V to 3.6 V, AVSS = VSS = 0 V, TA = −40 °C to +85 °C) Value Condition Unit Remarks Min Typ Max Differential linear error Zero transition voltage VOT Full scale transition voltage VFST Analog input voltage VAIN Reference voltage Reference voltage supply current IR IRH AN0 to AN7 AVR bit ±3.0 LSB ±2.5 LSB ±1.9 LSB AVR − 3.5 AVR − 1.5 AVR + 1.5 LSB LSB LSB mV 4.0 LSB 60 tinst µs 16 tinst µs 10 µA 0 AVR V AVSS + 2.4 AVCC V A/D running 200 µA A/D off 5 µA Sampling time IAIN 10 mV Analog input current AVR = AVCC AVSS − 1.5 AVSS + 0.5 AVSS + 2.5 LSB LSB LSB Inter-channel variation Conversion time AVCC = VCC * * : Includes sampling time 47 MB89530 Series (3) MB89P538/PV530 Parameter Symbol Pin name Resolution capability Total error Linear error (VCC = 2.4 V to 3.6 V, AVSS = VSS = 0 V, TA = −40 °C to +85 °C) Value Condition Unit Remarks Min Typ Max Differential linear error Zero transition voltage VOT Full scale transition voltage VFST AVR = AVCC Inter-channel variation Conversion time Sampling time Analog input current IAIN Analog input voltage VAIN Reference voltage Reference voltage supply current IR * : Includes sampling time 48 IRH 10 bit ±3.0 LSB ±2.5 LSB ±1.9 LSB AVSS − 1.5 AVSS + 0.5 AVSS + 2.5 LSB LSB LSB mV AVR − 3.5 AVR − 1.5 AVR + 1.5 LSB LSB LSB mV 4.0 LSB 60 tinst µs 16 tinst µs 10 µA 0 AVR V AN0 to AN7 AVSS + 3.5 AVCC V AVR A/D running 400 µA A/D off 5 µA AVCC = VCC * MB89530 Series (4) A/D Converter Terms and Definitions • Resolution The level of analog variation that can be distinguished by the A/D converter. • Linear error (unit : LSB) The deviation between the value along a straight line connecting the zero transition point (“00 0000 0000”←→“00 0000 0001”) of a device and the full-scale transition point (“11 1111 1110”←→“11 1111 1111”) , compared with the actual conversion values obtained. • Differential linear error (Unit : LSB) The deviation from the theoretical input voltage required to produce a change of 1 LSB in output code. • Total error (Unit : LSB) The difference between theoretical conversion value and actual conversion value. Theoretical input/output characteristics Total error VFST 3FF 3FF 3FE 1.5 LSB 3FD 004 003 VOT 002 Digital output Digital output 3FE 3FD Actual conversion characteristics (1 LSB I N + 0.5 LSB) 004 VNT 003 002 1 LSB 001 001 0.5 LSB AVSS AVR AVSS Analog input 1 LSB = VFST − VOT 1022 (V) Actual conversion characteristics Theoretical characteristics AVR Analog input Total error in digital output N = VNT − {1 LSB × N + 0.5 LSB} 1 LSB (Continued) 49 MB89530 Series (Continued) Zero transition error 004 Full-scale transition error Theoretical characteristics Actual conversion characteristics 3FF 002 Actual conversion characteristics 001 Digital output Digital output 003 VOT (actual measurement value) 3FF Digital output 3FE Actual conversion characteristics AVR Analog input Linear error Differential linear error Actual conversion characteristics Theoretical characteristics N+1 (1 LSB × N + VOT) VFST (actual VNT measure004 ment value) Actual conversion characteristics 003 002 Theoretical characteristics VOT (actual measurement value) AVSS AVR Analog input Analog input linear = error in digital output N 50 VFST (actual measurement value) 3FD Analog input 3FD 001 3FE 3FC VNT − {1 LSB × N + VOT} 1 LSB Digital output AVSS Actual conversion characteristics Actual conversion characteristics V (N + 1) T N N−1 N−2 AVSS VNT Actual conversion characteristics Analog input AVR Differential linear = V (N + 1) T − VNT −1 1 LSB error in digital output N MB89530 Series (5) Precautionary Information • Input Impedance of Analog Input Pins The A/D converter has a sample & hold circuit as shown below, which uses a sample-and-hold capacitor to obtain the voltage at the analog input pin for 8 instruction cycles following the start of A/D conversion. For this reason if the external circuits providing the analog input signal have high output impedance, the analog input voltage may not stabilize within the analog input sampling time. It is therefore recommended that the output impedance of external circuits be reduced to 10 kΩ or less. • MB89537/537C/538/538C/F538L Analog Input Equivalent Circuit Sample-and-hold circuit C = 49 pF Analog input pin If analog input impedance is 10 kΩ or more, the use of a capacitor of approximately 0.1 µF is recommended. Comparator R = 7.1 kΩ Closes 8 instruction cycles after the start of A/D conversion Analog channel selector • MB89P538 and MB89PV530 Analog Input Equivalent Circuit Sample-and-hold circuit C = 64 pF Analog input pin If analog input impedance is 10 kΩ or more, the use of a capacitor of approximately 0.1 µF is recommended. Comparator R = 3 kΩ Closes 8 instruction cycles after the start of A/D conversion Analog channel selector • About error The smaller the absolute value |AVR - AVss| is, the greater the relative error becomes. 51 MB89530 Series 6. Flash Memory • Flash memory programming/erase characteristics Parameter Conditions Per 1 sector, Sector erase Constant value indetime pendent with sector caTA = +25 °C, pacitance VCC = 3.3 V ProgramPer 1 byte ming time Chip erase time Program/Erase cycle * : Excludes internal programming time before erase. 52 Value Unit Min Typ Max 1 15 s 8 3600 µs 5 s 10,000 cycle Remarks * * MB89530 Series ■ EXAMPLE CHARACTERISTICS (1) Power Supply Current (External Clock) MB89538 ICCS1 vs. VCC MB89538 ICC1 vs. VCC 7 2.5 12.5 MHz (TA = 25 ˚C) 6 (TA = 25 ˚C) 10 MHz ICCS1 (mA) ICC1 (mA) 5 8 MHz 4 3 12.5 MHz 2 5 MHz 10 MHz 1.5 8 MHz 1 5 MHz 2 0.5 2 MHz 1 2 MHz 1 MHz 1 MHz 0 0 1 2 3 4 1 5 2 3 4 5 VCC (V) VCC (V) (2) “H” Level Input Voltage/ “L” Level Input Voltage (CMOS Input) MB89538 VIN vs. VCC 4 (TA = 25 ˚C) VIN (V) 3 2 1 0 2 2.5 3 3.5 4 VCC (V) (3) “H” Level Input Voltage / ”L” Level Input Voltage (Hysteresis Input) MB89538 VIN vs. VCC 3 (TA = 25 ˚C) VIH VIN (V) 2 VIL 1 0 2 2.5 3 3.5 4 VCC (V) 53 MB89530 Series (4) AD Converter Characteristic Example MB89538 Linearity Error 3 2.5 (VCC = AVR = 3 V, Fc = 10 MHz) 2 1.5 Error (LSB) 1 0.5 0 -0.5 -1 -1.5 -2 -2.5 -3 0 128 256 384 512 640 768 896 1024 Conversion characteristic MB89538 Differential linearity error 2.5 2 (VCC = AVR = 3 V, Fc = 10 MHz) Error (LSB) 1.5 1 0.5 0 -0.5 -1 -1.5 -2 -2.5 0 128 256 384 512 640 768 896 1024 Conversion characteristic MB89538 Total Error 4 Error (LSB) 3 (VCC = AVR = 3 V, Fc = 10 MHz) 2 1 0 -1 -2 -3 -4 0 128 256 384 512 640 Conversion characteristic 54 768 896 1024 MB89530 Series ■ MASK OPTIONS Part number MB89537 MB89537C MB89538 MB89538C MB89F538L-101 MB89F538L-201 MB89P538-101 MB89P538-201 MB89PV530-101 MB89PV530-201 Method of specification Specify at time of mask order Setting not possible Setting not possible Setting not possible No 1 Main clock Select oscillator stabilization wait period (FCH * = 10 MHz) approx.214/FCH * 218/FCH * 218/FCH * 218/FCH * Selection available (approx.1.6 ms) (approx. 26.2 ms) (approx. 26.2 ms) (approx. 26.2 ms) approx.217/FCH * (approx.13.1 ms) approx.218/FCH * (approx.26.2 ms) 2 Clock mode selection • 2-system clock mode • 1-system clock mode Selection available • 101 : 1-system clock mode • 201 : 2-system clock mode * : FCH : Main clock frequency 55 MB89530 Series ■ ORDERING INFORMATION Part number Remarks MB89537P MB89537CP MB89538P MB89538CP MB89F538L-101P MB89F538L-201P MB89P538-101P MB89P538-201P DIP-64P-M01 MB89537P and MB89538P do not have I2C functions. MB89537PF MB89537CPF MB89538PF MB89538CPF MB89F538L-101PF MB89F538L-201PF MB89P538-101PF MB89P538-201PF FPT-64P-M06 MB89537PF and MB89538PF do not have I2C functions. MB89537PFM MB89537CPFM MB89538PFM MB89538CPFM MB89F538L-101PFM MB89F538L-201PFM MB89P538-101PFM MB89P538-201PFM FPT-64P-M09 MB89537PFM and MB89538PFM do not have I2C functions. MB89537PFV MB89537CPFV MB89538PFV MB89538CPFV FPT-64P-M03 MB89537PFV and MB89538PFV do not have I2C functions. MB89F538L-101PV4 MB89F538L-201PV4 LCC-64P-M19 MB89F538-101PV* MB89F538-201PV* LCC-64P-M16* MB89PV530C-101 MB89PV530C-201 MDP-64C-P02 MB89PV530CF-101 MB89PV530CF-201 MQP-64C-P01 * : Only for ES 56 Package MB89530 Series ■ PACKAGE DIMENSIONS 64-pin, Plastic SH-DIP (DIP-64P-M01) Note: Pins width and pins thickness include plating thickness. +0.22 +.009 58.00 –0.55 2.283 –.022 INDEX-1 17.00±0.25 (.669±.010) INDEX-2 +0.70 4.95 –0.20 +.028 .195 –.008 +0.50 0.70 –0.19 +.020 .028 –.007 0.27±0.10 (.011±.004) +0.20 3.30 –0.30 .130 +.008 –.012 +0.40 1.378 –0.20 +.016 .0543 –.008 C 1.778(.0700) 0.47±0.10 (.019±.004) 19.05(.750) +0.50 0.25(.010) M 1.00 –0 +.020 0~15° .039 –.0 2001 FUJITSU LIMITED D64001S-c-4-5 Dimensions in mm (inches). Note: The values in parentheses are reference values (Continued) 57 MB89530 Series 64-pin, Plastic LQFP (FPT-64P-M03) Note 1) * : These dimensions do not include resin protrusion. Note 2) Pins width and pins thickness include plating thickness. Note 3) Pins width do not include tie bar cutting remainder. 12.00±0.20(.472±.008)SQ * 10.00±0.10(.394±.004)SQ 48 0.145±0.055 (.006±.002) 33 49 32 Details of "A" part 0.08(.003) +0.20 1.50 –0.10 +.008 .059 –.004 INDEX 64 0˚~8˚ 17 (Mounting height) 0.10±0.10 (.004±.004) (Stand off) "A" LEAD No. 1 16 0.50(.020) C 0.20±0.05 (.008±.002) 0.08(.003) M 0.50±0.20 (.020±.008) 0.60±0.15 (.024±.006) 0.25(.010) 2003 FUJITSU LIMITED F64009S-c-5-8 Dimensions in mm (inches). Note: The values in parentheses are reference values (Continued) 58 MB89530 Series 64-pin, Plastic QFP (FPT-64P-M06) Note 1) * : These dimensions do not include resin protrusion. Note 2) Pins width and pins thickness include plating thickness. Note 3) Pins width do not include tie bar cutting remainder. 24.70±0.40(.972±.016) * 20.00±0.20(.787±.008) 51 0.17±0.06 (.007±.002) 33 52 32 18.70±0.40 (.736±.016) *14.00±0.20 (.551±.008) INDEX Details of "A" part +0.35 3.00 –0.20 +.014 .118 –.008 64 (Mounting height) 20 0~8˚ 1 19 1.00(.039) 0.42±0.08 (.017±.003) 0.20(.008) +0.15 M 0.25 –0.20 1.20±0.20 (.047±.008) +.006 .010 –.008 (Stand off) "A" 0.10(.004) C 2003 FUJITSU LIMITED F64013S-c-5-5 Dimensions in mm (inches). Note: The values in parentheses are reference values (Continued) 59 MB89530 Series 64-pin, Plastic LQFP (FPT-64P-M09) Note 1) * : These dimensions do not include resin protrusion. Note 2) Pins width and pins thickness include plating thickness. Note 3) Pins width do not include tie bar cutting remainder. 14.00±0.20(.551±.008)SQ * 12.00±0.10(.472±.004)SQ 48 0.145±0.055 (.0057±.0022) 33 49 32 0.10(.004) Details of "A" part +0.20 1.50 –0.10 +.008 .059 –.004 (Mounting height) 0.25(.010) INDEX 0~8˚ 64 17 1 0.65(.026) C "A" 16 0.32±0.05 (.013±.002) 0.13(.005) 0.50±0.20 (.020±.008) 0.60±0.15 (.024±.006) 0.10±0.10 (.004±.004) (Stand off) M 2003 FUJITSU LIMITED F64018S-c-3-5 Dimensions in mm (inches). Note: The values in parentheses are reference values (Continued) 60 MB89530 Series 64-pin, Ceramic MDIP (MDP-64C-P02) 0°~9° 56.90±0.64 (2.240±.025) 15.24(.600) TYP 18.75±0.30 (.738±.012) 2.54±0.25 (.100±.010) 33.02(1.300)REF INDEX AREA 0.25±0.05 (.010±.002) 1.27±0.25 (.050±.010) 10.16(.400)MAX 1.778±0.25 (.070±.010) C 19.05±0.30 (.750±.012) +0.13 0.46 –0.08 +.005 .018 –.003 55.12(2.170)REF 0.90±0.13 (.035±.005) 3.43±0.38 (.135±.015) 1994 FUJITSU LIMITED M64002SC-1-4 Dimensions in mm (inches). Note: The values in parentheses are reference values (Continued) 61 MB89530 Series 64-pin, Ceramic MQFP (MQP-64C-P01) 18.70(.736)TYP INDEX AREA 16.30±0.33 (.642±.013) 15.58±0.20 (.613±.008) 12.00(.472)TYP +0.40 1.20 –0.20 .047 1.00±0.25 (.039±.010) +.016 –.008 1.00±0.25 (.039±.010) 1.27±0.13 (.050±.005) 22.30±0.33 (.878±.013) 24.70(.972) TYP 0.30(.012) TYP 1.27±0.13 (.050±.005) 18.12±0.20 12.02(.473) (.713±.008) TYP 10.16(.400) 14.22(.560) TYP TYP 0.30(.012)TYP 7.62(.300)TYP 18.00(.709) TYP 0.40±0.10 (.016±.004) 0.40±0.10 (.016±.004) +0.40 1.20 –0.20 +.016 .047 –.008 9.48(.373)TYP 11.68(.460)TYP 0.50(.020)TYP C 10.82(.426) 0.15±0.05 MAX (.006±.002) 1994 FUJITSU LIMITED M64004SC-1-3 Dimensions in mm (inches). Note: The values in parentheses are reference values (Continued) 62 MB89530 Series 64-pin, Plastic BCC (LCC-64P-M19) 49 8.20(.323)TYP 8.10(.319)TYP (0.80(.031)MAX) (Mount height) 9.00±0.10(.354±.004) 33 0.50(.020) TYP 33 0.50±0.10 (.020±.004) 49 0.50(.020) TYP 8.25(.325) REF INDEX AREA 9.00±0.10 (.354±.004) 8.20(.323) TYP 8.10(.319) TYP 7.00(.276) REF 0.50±0.10 (.020±.004) "A" 1 17 0.075±0.025 17 "C" (.003±.001) (Stand off) Details of "A" part 0.05(.002) C 2002 FUJITSU LIMITED C64019S-c-1-1 0.60±0.06 (.024±.002) 0.30±0.06 (.012±.002) 0.14(.006)MIN. 0.70±0.06 (.028±.002) 0.30±0.06 (.012±.002) 7.00(.276)REF "B" 1 8.25(.325)REF Details of "B" part 0.55±0.06 (.022±.002) C0.2(.008) 0.55±0.06 (.022±.002) Details of "C" part 0.55±0.06 (.022±.002) 0.55±0.06 (.022±.002) Dimensions in mm (inches). Note: The values in parentheses are reference values (Continued) 63 MB89530 Series (Continued) 64-pin, Plastic BCC (LCC-64P-M16) 8.20(.323)TYP 7.00(.276)REF 9.00±0.10(.354±.004) 49 (0.80(.031)MAX) (Mount height) 0.50(.020) TYP 33 33 0.50±0.10 (.020±.004) 49 0.50(.020) TYP 8.15(.321) REF 7.00(.276) REF 8.20(.323) TYP 9.00±0.10 (.354±.004) INDEX AREA 0.50±0.10 (.020±.004) 1 17 17 0.075±0.025 (.003±.001) (Stand off) Details of "A" part 0.14(.006) MIN "B" "A" "C" Details of "B" part 0.40±0.06 (.016±.002) 1 8.15(.321)REF C0.2(.008) Details of "C" part 0.45±0.06 (.018±.002) 0.45±0.06 (.018±.002) 0.05(.002) 0.30±0.06 (.012±.002) C 0.45±0.06 (.018±.002) 0.45±0.06 (.018±.002) 2001 FUJITSU LIMITED C64016S-c-2-1 Dimensions in mm (inches). Note: The values in parentheses are reference values 64 MB89530 Series FUJITSU LIMITED All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of Fujitsu semiconductor device; Fujitsu does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. Fujitsu assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of Fujitsu or any third party or does Fujitsu warrant non-infringement of any third-party’s intellectual property right or other right by using such information. Fujitsu assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that Fujitsu will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be required for export of those products from Japan. F0303 FUJITSU LIMITED Printed in Japan