GF1A THRU GF1M 50V-1000V 1.0A SURFACE MOUNT GLASS PASSIVATED JUNCTION RECTIFIER FEATURES l l l l l l l l l Plastic package has Underwriters Laboratory Flammability Classification 94V-0 Ideal for surface mount automotive applications High temperature metallurgically bonded construction Glass passivated cavity-free junction High temperature soldering guaranteed: 450°C/5 seconds at terminals Complete device submersible temperature of 265°C for 10 seconds in solder bath MECHANICAL DATA Case: JEDEC DO-214BA molded plastic over glass body Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.0048 ounces, 0.120 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS Device marking code GF1A GF1B GF1D GF1G GF1J GF1K GF1M UNITS GA GB GD GG GJ GK GM Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 Volts Maximum average forward rectified current at TL=125°C I(AV) 1.0 Amp Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 30.0 Amps VF 1.10 IR 5.0 50.0 Maximum instantaneous forward voltage at 1.0A Maximum DC reverse current at rated DC blocking voltage TA=25°C TA=125°C 1.20 Volts µA Typical reverse recovery time (NOTE 1) trr 2.0 µs Typical junction capacitance (NOTE 2) CJ 15.0 pF RΘJA RΘJL 80.0 26.0 °C/W TJ, TSTG -65 to +175 °C Typical thermal resistance (NOTE 3) Operating junction and storage temperature range NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied VR=4.0 Volts (3) Thermal resistance from junction to ambient and from junction to lead P.C.B. mounted on 0.2 x 0.2” (5.0 x 5.0mm) copper pad areas E-mail: [email protected] 1 of 2 Web Site: www.taychipst.com GF1A THRU GF1M 50V-1000V 1.0A SURFACE MOUNT GLASS PASSIVATED JUNCTION RECTIFIER RATINGS AND CHARACTERISTIC CURVES FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 30 60 HZ RESISTIVE OR INDUCTIVE LOAD P.C.B. MOUNTED on 0.2 x 0.2” (5.0 x 5.0mm) COPPER PAD AREAS PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 1 - FORWARD CURRENT DERATING CURVE 1.0 0.5 0 100 110 120 130 140 150 160 GF1A THRU GF1M 175 TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 25 20 15 10 5.0 0 LEAD TEMPERATURE, °C 1 10 100 NUMBER OF CYCLES AT 60 HZ FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 10 FIG. 4 - TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 1 0.1 1 TJ=100°C 0.1 TJ=25°C 0.01 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 10 TRANSIENT THERMAL IMPEDANCE (°C/W) JUNCTION CAPACITANCE, pF TJ=25°C f=1.0 MHZ Vsig=50mVp-p 10 100 60 80 100 100 MOUNTED ON 0.20 x 0.27” (5 x 7mm) COPPER PAD AREAS 10 1 0.1 0.01 0.1 1 10 100 t, PULSE DURATION, sec REVERSE VOLTAGE, VOLTS E-mail: [email protected] 40 FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE FIG. 5 - TYPICAL JUNCTION CAPACITANCE 30 1 20 PERCENT OF RATED PEAK REVERSE VOLTAGE, % INSTANTANEOUS FORWARD VOLTAGE, VOLTS 1 0 2 of 2 Web Site: www.taychipst.com