Data Sheet VOLTAGE DETECTOR AZ70XX General Description Features The AZ70XX series ICs are under voltage detectors with a built in voltage threshold and low power consumption. The AZ70XX are specifically designed to accurately monitor power supplies. · · The AZ70XX use a precision on-chip voltage reference and a comparator to measure the input operating voltage. These ICs can accurately reset the system after detecting voltage at the time of switching power on and instantaneous power off in various CPU systems and other logic systems. The detect voltage thresholds are 2.3V/2.5V/2.7V/2.9V/3.1V/3.3V/4.2V/4.5Vfor AZ7023/25/27/29/31/33/42/45 respectively. Built in hysteresis helps to prevent erratic operation in the presence of noise. · · · Applications · · · · · The AZ70XX series are available in 2 standard packages: TO-92 (bulk or ammo packing) and SOT-89. TO-92(Bulk Packing) Low Current Consumption: ICCL=300µA Typical ICCH=30µA Typical Low Minimum Operating Voltage for Output Resetting: 0.8V Typical Built in Hysteresis Voltage: 50mV Typical Open Collector Output Extended Temperature Range: -40 to 85oC Low Battery Voltage Detector Power Fail Indicator Processor Reset Generator Battery Backup Control Home Electric Appliances TO-92(Ammo Packing) SOT-89 Figure 1. Package Types of AZ70XX Oct. 2011 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 1 Data Sheet VOLTAGE DETECTOR AZ70XX Pin Configuration Z Package (TO-92(Bulk Packing)) Z Package (TO-92(Ammo Packing)) 3 OUT 3 OUT 2 GND 2 GND 1 VCC 1 VCC R Package (SOT-89) 1 2 VCC 3 GND OUT Figure 2. Pin Configuration of AZ70XX (Top View) Functional Block Diagram VCC OUT + - GND Figure 3. Functional Block Diagram of AZ70XX Oct. 2011 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 2 Data Sheet VOLTAGE DETECTOR AZ70XX Ordering Information - AZ70 E1: Lead Free G1: Green Circuit Type TR: Tape and Reel or Ammo Blank: Bulk Detect Voltage 23: 2.3V 31: 3.1V 25: 2.5V 33: 3.3V 27: 2.7V 42: 4.2V 29: 2.9V 45: 4.5V Package Temperature Range Detect Voltage 2.3V 2.5V 2.7V 2.9V TO-92 -40 to 85oC 3.1V 3.3V 4.2V -40 to 85oC Part Number Lead Free Marking ID Green Lead Free Green Packing Type AZ7023Z-E1 AZ7023Z-G1 AZ7023Z-E1 AZ7023Z-G1 Bulk AZ7023ZTR-E1 AZ7023ZTR-G1 AZ7023Z-E1 AZ7023Z-G1 Ammo AZ7025Z-E1 AZ7025Z-G1 AZ7025Z-E1 AZ7025Z-G1 Bulk AZ7025ZTR-E1 AZ7025ZTR-G1 AZ7025Z-E1 AZ7025Z-G1 Ammo AZ7027Z-E1 AZ7027Z-G1 AZ7027Z-E1 AZ7027Z-G1 Bulk AZ7027ZTR-E1 AZ7027ZTR-G1 AZ7027Z-E1 AZ7027Z-G1 Ammo AZ7029Z-E1 AZ7029Z-G1 AZ7029Z-E1 AZ7029Z-G1 Bulk AZ7029ZTR-E1 AZ7029ZTR-G1 AZ7029Z-E1 AZ7029Z-G1 Ammo AZ7031Z-E1 AZ7031Z-G1 AZ7031Z-E1 AZ7031Z-G1 Bulk AZ7031ZTR-E1 AZ7031ZTR-G1 AZ7031Z-E1 AZ7031Z-G1 Ammo AZ7033Z-E1 AZ7033Z-G1 AZ7033Z-E1 AZ7033Z-G1 Bulk AZ7033ZTR-E1 AZ7033ZTR-G1 AZ7033Z-E1 AZ7033Z-G1 Ammo AZ7042Z-E1 AZ7042Z-G1 AZ7042Z-E1 AZ7042Z-G1 Bulk AZ7042ZTR-E1 AZ7042ZTR-G1 AZ7042Z-E1 AZ7042Z-G1 Ammo AZ7045Z-E1 AZ7045Z-G1 AZ7045Z-E1 AZ7045Z-G1 Bulk AZ7045ZTR-E1 AZ7045ZTR-G1 AZ7045Z-E1 AZ7045Z-G1 Ammo 2.3V AZ7023RTR-E1 AZ7023RTR-G1 E723 G70A Tape & Reel 2.5V AZ7025RTR-E1 AZ7025RTR-G1 E725 G70G Tape & Reel 2.7V AZ7027RTR-E1 AZ7027RTR-G1 E727 G70B Tape & Reel 2.9V AZ7029RTR-E1 AZ7029RTR-G1 E729 G70C Tape & Reel 3.1V AZ7031RTR-E1 AZ7031RTR-G1 E731 G70H Tape & Reel 3.3V AZ7033RTR-E1 AZ7033RTR-G1 E733 G70D Tape & Reel 4.2V AZ7042RTR-E1 AZ7042RTR-G1 E742 G70E Tape & Reel 4.5V AZ7045RTR-E1 AZ7045RTR-G1 E745 G70F Tape & Reel 4.5V SOT-89 Package Z: TO-92 R: SOT-89 BCD Semiconductor's Pb-free products, as designated with "E1" suffix in the part number, are RoHS compliant. Products with "G1" suffix are available in green packages. Oct. 2011 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 3 Data Sheet VOLTAGE DETECTOR AZ70XX Absolute Maximum Ratings (Note 1) Parameter Supply Voltage Symbol Value Unit VCC -0.3 to 20 V TO-92 Package: 400 Power Dissipation (Package Limitations, TA=25oC) PD Operating Junction Temperature TJ 150 oC TSTG -65 to 150 oC Storage Temperature Range SOT-89 Package: 500 mW Note 1: Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under"Recommended Operating Conditions" is not implied. Exposure to "Absolute Maximum Ratings" for extended periods may affect device reliability. Recommended Operating Conditions Parameter Supply Voltage Operating Temperature Range Symbol Min VCC TA -40 Max Unit 18 V 85 oC BCD Semiconductor Manufacturing Limited Oct. 2011 Rev. 2. 2 4 Data Sheet VOLTAGE DETECTOR AZ70XX Electrical Characteristics TA=25oC, unless otherwise specified. Parameter Detect Voltage Symbol VDET Conditions RL=200Ω (Note 2) VOL ≤ 0.4V Min Typ Max AZ7023R/Z 2.15 2.3 2.45 AZ7025R/Z 2.35 2.5 2.65 AZ7027R/Z 2.55 2.7 2.85 AZ7029R/Z 2.75 2.9 3.05 AZ7031R/Z 2.95 3.1 3.25 AZ7033R/Z 3.15 3.3 3.45 AZ7042R/Z 4.05 4.2 4.35 AZ7045R/Z 4.35 4.5 4.65 Unit V Low-level Output Voltage VOL VCC=VDET(min)-0.05V RL=200Ω (Note 2) 0.4 V Output Leakage Current IOH VCC=18V 0.1 µA 100 mV Hysteresis Voltage VHYS RL=200Ω (Note 2) 30 50 Detect Voltage Temperature Coefficient ∆VDET/(VDET Circuit Current at On Time ICCL VCC=VDET(min)-0.05V 300 500 µA Circuit Current at Off Time ICCH VCC=5.25V 30 50 µA Minimum Operating Voltage VOPR “L”Transmission Delay Time tpHL tpLH “H”Transmission Delay Time × ∆T) IOL Ⅰ Output Current at On Time IOL Ⅱ Thermal Resistance (Junction to Case) θJC ±0.01 RL=200Ω (Note 2) RL=200Ω (Note 2) % / oC 0.8 V VCC changed from 5.25V to VDET(min)-0.05V, RL=1.0KΩ, CL=100p (Note 3) 10 µs VCC changed from VDET(min)0.05V to 5.25V, RL=1.0KΩ, CL=100p (Note 3) 15 µs VOL ≤ 0.4V VCC=VDET(min)-0.05V 20 TA=25oC (Note 4) mA VCC=VDET(min)-0.05V TA=-40 to 85 oC (Note 4) 16 TO-92 72 SOT-89 74 o C/W Note 2: See test circuit 1 and Figure 12. Note 3: See test circuit 2 and Figure 12. Note 4: See test circuit 3. Adjusting the regulative power source until the reading value of voltage meter V is 0.4V, the reading value of current meter A is defined as "Output Current at On Time". BCD Semiconductor Manufacturing Limited Oct. 2011 Rev. 2. 2 5 Data Sheet VOLTAGE DETECTOR AZ70XX Electrical Characteristics (Continued) A1 A2 1 RL VCC AZ7029 V1 3 OUT + GND 2 10µF V2 Figure 4. Test Circuit 1 RL 1 VCC Input Pulse AZ7029 + OUT GND +5V 10µF 3 CL 2 Figure 5. Test Circuit 2 1 VDET(min)-0.05V + V CC 10µF AZ7029 OUT GND 2 3 A V Figure 6. Test Circuit 3 Oct. 2011 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 6 Data Sheet VOLTAGE DETECTOR AZ70XX Typical Performance Characteristics 1200 2.95 1100 Minimum Operating Voltage (mV) AZ7029 Detect Voltage (V) 2.90 VDET+ (VCC Rising) 2.85 VDET- (VCC Falling) 2.80 2.75 -40 -20 0 20 40 60 1000 AZ7029 900 800 700 600 500 400 -40 80 -20 0 40 60 80 Temperature ( C) Temperature ( C) Figure 7. Detect Voltage vs. Temperature Figure 8. Minimum Operating Voltage vs. Temperature 100 Low-level Output Voltage (mV) 70 Output Current at On Time (mA) 20 O O 60 50 AZ7029 40 30 75 AZ7029 50 25 20 10 -40 -20 0 20 40 60 0 -40 80 -20 0 20 40 60 80 O Temperature ( C) O Temperature ( C) Figure 9. Output Current at On Time vs. Temperature Figure 10. Low-level Output Voltage vs. Temperature BCD Semiconductor Manufacturing Limited Oct. 2011 Rev. 2. 2 7 Data Sheet VOLTAGE DETECTOR AZ70XX Typical Performance Characteristics (Continued) Time (s) Figure 11. Output Voltage Dynamic Response when VCC Increases and Decreases Operating Diagram VCC VDET+ VHYS VDETVOPR GND VOUT tpHL tpLH tpHL tpLH Figure 12. AZ70XX Timing Waveform (Note 5) Note 5: Detect voltage: VDETHysteresis voltage (VHYS): VDET+-VDET- Release voltage: VDET+ Minimum operating voltage: VOPR Oct. 2011 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 8 Data Sheet VOLTAGE DETECTOR AZ70XX Operating Diagram (Continued) typical). Below minimum operating voltage, the output is undefined. Figure 12 is a typical timing waveform for AZ70XX. In normal steady-state operation when VCC>VDET-, the output will be in a logic high state and VOUT is dependent upon the voltage that the pull-up resistor connected to. 3. During power-up, VOUT will remain undefined until VCC rises above VOPR, at which time the output will become valid. VOUT will be in its active low state while VOPR<VCC<VDET+ (VDET+=VDET-+VHYS). VDET+ is the release voltage. VHYS means the hysteresis voltage and is the difference voltage between the VDET+ and VDET-. Here is some explanations for AZ70XX's operation. 1. When the input voltage VCC falls below VDET-, the output will pull down to logic low after a delay time of tpHL. In general, at rated output current and VCC, VOUT can be pulled down to a voltage as low as within 0.4V from GND. (See the Electrical Characteristics section). The voltage level VDET- means the detect voltage. 4. When VCC rises above VDET+, the output will be in its inactive state. After a delay time of tpLH, VOUT will be in its logic high state . 2. The output, VOUT, will stay valid until VCC falls below the minimum operating voltage, VOPR (0.8V Typical Applications VCC +5V VCC R1 220 1 1 VCC AZ70XX VCC OUT GND R1 3.3k 3 AZ70XX OUT 2 Figure 13. Low Voltage Indicator RESET + GND LED 2 VCC 3 CPU GND C1 1 µF Figure 14. CPU Resetting Circuit BCD Semiconductor Manufacturing Limited Oct. 2011 Rev. 2. 2 9 Data Sheet VOLTAGE DETECTOR AZ70XX Mechanical Dimensions TO-92(Bulk Packing) Unit: mm(inch) 1.000(0. 039) 3.430(0.135) MIN 3.700(0.146) 3.300(0.130) 1.400(0. 055) 0.320(0. 013) 0.510(0. 020) 0. 000(0. 000) 0. 380(0. 015) Φ1. 600(0. 063) MAX 4.700(0.185) 1.270(0. 050) TYP 15.500(0.610) 0.360(0. 014) 0.760(0. 030) 12.500(0.492) 4.300(0.169) 4.400(0.173) 4.800(0.189) 2.420(0.095) 2.660(0.105) Oct. 2011 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 10 Data Sheet VOLTAGE DETECTOR AZ70XX Mechanical Dimensions (Continued) TO-92(Ammo Packing) Unit: mm(inch) 1. 100(0. 043) 3. 430(0.135) MIN 1.270(0.050) Typ 2.500(0.098) 4.000 (0.157 ) 0. 000(0.000) 0. 380(0.015) Φ1. 600(0. 063) Φ MAX 14.500(0.571) 12.500(0.492) 0.320(0. 013) 0. 510(0. 020) 3.800(0.150) 3.300(0.130) 1. 400(0.055) 4.700(0.185) 4.300(0.169) 4.400(0.173) 4.800 (0.189 ) 13.000(0. 512) 15.000 (0.591 ) 0.380(0.015) 0.550(0.022 ) 2.540(0.100) Typ Oct. 2011 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 11 Data Sheet VOLTAGE DETECTOR AZ70XX Mechanical Dimensions (Continued) SOT-89 1.550(0.061)REF Unit: mm(inch) 4.400(0.173) 4.600(0.181) 1.400(0.055) 1.600(0.063) 1.030(0.041)REF 45 2.300(0.091) 2.600(0.102) 3.950(0.156) 4.250(0.167) 2.060(0.081)REF 3 0.900(0.035) 1.100(0.043) 0.320(0.013) 0.520(0.020) 0.480(0.019) 0.320(0.013) 0.520(0.020) 10 0.350(0.014) 0.450(0.018) 3.000(0.118) TYP 1.500(0.059) 1.800(0.071) 0.320(0.013)REF 3 2.210(0.087)REF 1.620(0.064)REF R0.150(0.006) 10 Oct. 2011 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 12 BCD Semiconductor Manufacturing Limited http://www.bcdsemi.com IMPORTANT NOTICE IMPORTANT NOTICE BCD Semiconductor BCD Semiconductor Manufacturing Manufacturing Limited Limited reserves reserves the the right right to to make make changes changes without without further further notice notice to to any any products products or or specifispecifications herein. cations herein. BCD BCD Semiconductor Semiconductor Manufacturing Manufacturing Limited Limited does does not not assume assume any any responsibility responsibility for for use use of of any any its its products products for for any any particular purpose, particular purpose, nor nor does does BCD BCD Semiconductor Semiconductor Manufacturing Manufacturing Limited Limited assume assume any any liability liability arising arising out out of of the the application application or or use use of any of any its its products products or or circuits. circuits. BCD BCD Semiconductor Semiconductor Manufacturing Manufacturing Limited Limited does does not not convey convey any any license license under under its its patent patent rights rights or or other rights other rights nor nor the the rights rights of of others. others. MAIN SITE SITE MAIN - Headquarters BCD Semiconductor Manufacturing Limited BCD Semiconductor Manufacturing Limited - Wafer Fab No. 1600, Zi Xing Road, Shanghai ZiZhu Science-basedLimited Industrial Park, 200241, China Shanghai SIM-BCD Semiconductor Manufacturing Tel: Fax: +86-21-24162277 800,+86-21-24162266, Yi Shan Road, Shanghai 200233, China Tel: +86-21-6485 1491, Fax: +86-21-5450 0008 REGIONAL SALES OFFICE Shenzhen OfficeSALES OFFICE REGIONAL - Wafer FabSemiconductor Manufacturing Limited BCD Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd. - IC Design Group 800 Yi Shan Road, Shanghai 200233, China Corporation Advanced Analog Circuits (Shanghai) Tel: +86-21-6485 1491,YiFax: 0008200233, China 8F, Zone B, 900, Shan+86-21-5450 Road, Shanghai Tel: +86-21-6495 9539, Fax: +86-21-6485 9673 Taiwan Office Shanghai Semiconductor Manufacturing Co., Ltd., Shenzhen Office BCD Taiwan Semiconductor Shenzhen SIM-BCD Office Office (Taiwan) Company Limited Unit A Room 1203, Skyworth Bldg., Gaoxin Ave.1.S., Nanshan Shenzhen, 4F, 298-1, Guang Road,(Taiwan) Nei-Hu District, Taipei, Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd.District, Shenzhen Office BCDRui Semiconductor Company Limited China Taiwan Advanced Analog Circuits (Shanghai) Corporation Shenzhen Office 4F, 298-1, Rui Guang Road, Nei-Hu District, Taipei, Tel: +86-755-8826 Tel: +886-2-2656 2808 Room E, 5F, Noble 7951 Center, No.1006, 3rd Fuzhong Road, Futian District, Shenzhen 518026, China Taiwan Fax: +86-755-88267951 7865 Fax: +886-2-2656 28062808 Tel: +86-755-8826 Tel: +886-2-2656 Fax: +86-755-8826 7865 Fax: +886-2-2656 2806 USA Office BCD Office Semiconductor Corp. USA 30920Semiconductor Huntwood Ave.Corporation Hayward, BCD CA 94544, USA Ave. Hayward, 30920 Huntwood Tel :94544, +1-510-324-2988 CA U.S.A Fax:: +1-510-324-2988 +1-510-324-2788 Tel Fax: +1-510-324-2788